Electrolux E42BS75EPS Owner's manual

Brand: Electrolux

Model: E42BS75EPS

Category: Fridges

Type: Owner's manual

This manual is also suitable for

E42BS75ETT

www.ElectroluxUSA.com

Safety Instructions ........... 2-4

Operating Instructions

Automatic Ieemaker ........... 10

Care and Cleaning .......... 12, 13

Drawers and Baskets ............ 9

Ice and Water Dispenser ..... 10, 11

Refrigerator Doors ............. 8

Replacing the Light Bulbs ....... 14

Shelves and Bins ............... 7

Temperature Controls ........... 5

Water Filter ................... 6

Installation Instructions

Anti-Tip Brackets .............. 30

Dimensions, Clearances ........ 17

Door, Grille Panels ......... 32, 33

Installation Space ............. 17

Leveling ..................... 31

Panel Dimensions .......... 21-26

Stainless Steel Handles ......... 34

Water Line ................... 29

Water Supply ................. 35

Troubleshooting Tips ....... 38 40

Normal Operating Sotnlds ...... 37

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 43

State of California Water

Treatment Device Certificate ..... 44

Warranty (Canadian) ........... 41

Warranty (U.S.) ............... 42

Write the model and serial numbers here:

Model #

Serial #

Find these numbers on a label inside

tile refl'igerator coinpartinent at tile

top on the right side.

Model42

Electrolux Icon C6te a C6te

ROfrigOrateurs

La section franGaise commence a la page 45

Electrolux Icon Lado a Lado

Refrigeradores

ta seccion en espat)ol empieza en la pagina 88

DA99-00689C REV(0,0)

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

a, WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following."

This refiigerator must be properly hlstalled

a]ld located in accordance with tile Installation

Instructions before it is used.

Do not allow children to climb, stgu_dor hang

on the shelves in the refligerator. They could

dmnage the refligerator and seriously injure

theinselves.

Do not touch the cold surfaces in the fl'eezer

coinpartinent when hands are damp or wet. Skin

may stick to these extreinely cold surfaces.

Do not store or use gasoline or other fleaninable

vapors ea_d licit, Ms in the vicinity of this or may

other appliealce.

In refligerators with autoinatic iceinakei3,

avoid contact with the moving pea'ts of the

ejector inechanism, or with the heating element

located on the bottoin of the iceinaker. Do not

place fingers or hgulds on the autoinatic

icemaking mechallisin while the refligerator

is plugged in.

Kee I) fingers out of the "pinch point" areas;

clearances between the doors fund between

the doors and cabinet are necesseaily small.

Be careful closh_g doors when children are

h_ the area.

Set the master power switch to the 0 (off) position

before cleaning or maMng repairs.

NOTE."Westronglyrecommendthatany,servicingbe

performedbya qualifiedindividual

Do not refreeze frozen foods that have

thawed coinpletely.

ElectmluxUSA.com

DANGER!RISK OFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Child entrapment and suffocation ewe not problems

of the past. Junked or abandoned refl'igerators ewe

still dangerous...even if they will sit for '_ust a few

days." If you are getting rid of your old refl'igerator,

please follow the instructions below to help prevent

accidents.

Before You Throw Away YourOld Refrigerator

or Freezer:

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refl'igeration product, check with the

company handling the disposal about what

to do.

Take off the doors.

Leave the shelves in place so that children iilay

not easily cliinb inside.

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

WARNING!

HOWTOCONNECTELECTRICITY

Donot, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

Tile power coid of this appliance i.sequipped

with a 3-prong (grounding) plug, which mates

with a staaldard 3-prong (grounding) wall outlet

to mhlimize the possibility of electric shock hazard

fl'om tilts appliaalce.

Have the wall outlet aid circuit checked by a

qualified electricial to make sure the outlet is

properly grounded.

If the outlet is a staldgu'd 2-prong outlet, it i.syour

personal responsibility auld obligation to have it

replaced with a properly grounded 3-prong wall

outlet.

Tile refl'igerator should always be plugged into its

own hldividual electrical outlet which has a voltage

rating that matches the rating plate.

This provides tile best performance guld also

prevents overloading house wiring circuits, which

could cause a fire hazard fl'oin overheated wires.

Never unplug your refl'igerator by pullhlg on tile

power cord. Alwaysgrip plug fh'mly and pull straight

out fl'om the outlet.

Repair or replace immediately all power cords that

have become fl'ayed or otherwise daanaged. Do not

use a cord that shows cracM or abrasion damage

along its length or at either end.

When moving the refl'igeratoL be cax'eflfl not to roll

over or daanage the power cord.

DONOTUSEANADAPTERPLUGOREXTENSIONCORD

(Adapterplugsnotpermittedin Canada)

Donot use an adapter plug to connect the refrigerator to a 2-prong outlet.

Do not use an extension cord with this appliance.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthetemperaturecontrols. ElectroluxUSA.com

--_l ]l

The temperature controls are preset in the factory at 37°F for the

refrigerator compartment and O°F for the freezer compartment. Allow

24 hours for the temperature to stabilize to the preset recommended

settings.

The actual temperature may vary slightly from the set temperature

based on usage and operating environment.

NOTE: The refrigerator is shipped with protective film covering the

temperature controls, if this film was not removed during installation,

remove it now.

To change the teinperature, press and release the

up or drawn arrow button. To change tile

temperature, tap either tile up alTOW for wariner

temperatures or the down al'row for colder

temperatures until the desh'ed temperature is

displayed. Refl'igerator teinperatures call be

adjusted between 34 °F and 46°F alld the fl'eezer

teinperatures call be adjusted between -6 °F alld +

6°F.

Once tile desh'ed teinperature has been set,

the temperature display will clear after 60 seconds.

To display the teinperature, the Disp romp button

inay be tapped.

Several adjustinents Inay be required. Each thne you

adjust controls, allow 24 hours for the refl'igerator to

reach the teinperature you have set.

PerformanceAir FlowSystem

Tile Perfonnallce AipFlow SysteIn is designed to

inaxiinize temperature control in the refl'igerator

and fl'eezer compartments. This unique special

feature consists of the Air Tower along the back

wall of tile refl'igerator and tile fl'eezer. Placing food

hi fl'ont of the louvers on these components will not

affect performallce.

About the water filter. (o.somemodels)

Water Filter Cartridge

The water filter is located in tile fresh food

compea'tment ha the upper right side.

When to Replace the Filter

There is a replacement indicator light for

the water filter cea'tridge on the dispenser.

Tilts light will turn ainber to tell you that

you need to replace the filter soon.

The filter cartridge shotdd be replaced

when the replacement indicator light turns

red or if the flow of water to the dispenser

or icemaker decreases.

Installing the Filter Cartridge

The filter cartridge is designed to filter for

approximately 6 months under normal

household usage

O If you are replacing the cartridge,

first remove the old one by

depressing the ejection button

O Insert the new filter with

approximately 1 lb. of force so that

the filter is coinpletely seated

NOTE:If the filter is not seated properly,

water inay leak fl'oin the filtration systein or

no water will be dispensed.

O Run water fl'om the dispenser for

3 minutes (about l l/zgallons) to clear

the systein and prevent sputtering.

Press mid hold the [_button on the

dispenser for 3 seconds.

NOTE:The dispenser and the icemaker

will not operate without the filter.

Replacement Filters:

Toorderadditional filter cartridges

in the UnitedStates, visit our Website,

ElectroluxUSA.com or carl 1-877-

4ELECTROLUX

Abouttheshelvesandbins. Elec ol,xUSAcom

Not all features are on all models.

Refrigera[or olns

Refrigerator Door Bins and Freezer Door Bins

All door bins, except for the deep gallon

door bin and fl'eezer bins, ewe adjustable

and can be inoved up and down to ineet

your storage needs. The deep gallon door

bhl guld the fl'eezer bins can be reinoved

for cleealh_g.

Toremoveanybin:Lift the bin up eald pull

it towai'd you.

Toreplace or relocate: Engage the back side

of the bin in tile Inolded supports on the

dooI: Then push down on the fl'ont of the

bhl. Bin will lock in place.

The snugger helps prevent tipph_g, spillh_g

or slidh_g of sinall iteins stored on the door

shelf. Place a fh_ger on either side of the

snugger near the rear and inove it back

and forth to fit your needs.

Donotblock

Top freezer bin

CAUTION: Make

surethat items do

not btockor fall into

) theicechute.

Spillproof Shelves and Freezer Shelves

The special edges are designed to help

prevent spills fl'om dripping to lower

shelves.

Toremove shelves:

Tilt shelf up at fI'Ollt, then lift it up _u'_dout

of tracM on mew wall of refl'igerator.

Toreplace shelves:

Select desired shelf height. With shelf front

raised slightly, engage top lugs h_ tracks at

rear of cabhlet. Then lower fl'ont of shelf

until it locks into position.

Make sureyou push the shelves all the way back

in before you close the doo_

Abouttherefrigeratordoors.

Refrigerator Doors

The refrigerator doors may feel different

thm_ the ones you ewe used to. Tile special

door opening/closing feature inakes sure

the doors close all the way mlcl are securely

sealed.

When opening ea_d closing the door,

you will notice a stop position. When the

door is at the 90 ° stop position, it will

autoinatically close.

The resistance you feel at the stop

position will be reduced as the door

is loaded with food.

When thedoor is at 90°open,

it will automatically close,

Beyondthis step thedoor wilt stayopen,

DoorAlignment

If doors ewe uneven, adjust the refrigerator

dooI'.

Usln a **

0 ' g 7/32 socket wrench, turnthe

door adjusting screw clockwise to raise

the dooi; counterclockwise to lower

the door. (A @on plug, imbedded in

the tl_'eads of the pin, prevents the pin

fi'om turning unless a wrench is used.)

After one or two turns of the wrench,

open and close the refl'igerator door

ealcl check the alignment at the top

of the clooi3.

Aboutthedrawersandbaskets. Elec oluxUSAcom

Not all features are on all models.

Fruit and Vegetable Drawers

Excess water that inay accumulate in the

bottoin of the clrawei3 should be wiped dry.

crisper

0_ humidity con_ro

Adjustable Humidity Drawers

S1Me the control all the way to the Hlsetth_g

to provide high humidity recommended for

inost vegetables.

Slide the control all the way to the LO

setting to provide lower humidity levels

recoininended for inost fl'uits.

How to Remove and Replace the Drawers and Freezer Baskets

Toremove freshfood drawers: Toreplace freshfooddrawers:

O Pull the desired drawer out to the O Tip the back rollers of the drawer

stop position, behhld the rollers in the track.

O Lift up slightly on the front of the

drawer.

Lower the front of the drawer into

normal position.

Pull the drawer slightly forward and

out of the refl'igerator.

Slide the drawer to the back of the

refl'igeratoi:

Toremovefreezer baskets:

Pull the desh'ed basket out to the

stop position.

Lift up slightly on the front of the

basket.

Pull the basket slightly forwaa'd and

out of the fl'eezer.

Toreplace freezer baskets:

Place the back corners in the rail

with the basket tilted up.

Lower the basket clown to the norinal

position.

Slide the basket to the back of the

fl'eezei:

Abouttheice and water dispenserandautomaticicemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

AccessDoor/_.--

IceStorag_Bin //-

"L2

Ice Storage Bin

Toremove:

Lift up the access door to reach the

icemaker. Set tile iceinaker power switch

to the O (0f/) position. With the access

door closed, support the storage bin at

the bottom while slightly lifting. Pull bin

straight out.

Mechanism

Toreplace:

Slkle the bin back until the tab on

the bin locks into the slot on the shelf.

If the bin does not go all the way back,

reinove it and rotate tile drive mechanisin

1/4 turn. Then push the bin back again.

Important facts about your

ice and water dispenser

Do not add ice fl'oln trays or bags to tile

storage bin. It inay not crush or dispense

well.

Avoid overfilling glass with ice eald use of

narrow or extra-tall glasses. Backed-up ice

can jam tile chute or cause tile door in

tile chute to freeze shut. If ice Lsblocking

tile chute, poke it through with a wooden

spoon.

Beverages and foods should not be

quick-chilled M tile ice storage bin.

Caals, bottles or food packages in the

storage bin may cause the iceinaker

or auger to jean.

{{{{{{To keep dispensed ice fl'om missing

the glass, put the glass close to, but not

touchMg, the dispenser opening.

{{{{{{Some crushed ice may be dispensed

even though you selected Cubed Ice.

This hal)pens occasionally when a few

cubes accidentally get dit'ected to the

cI'usheI',

{{{{{{After crushed ice is dispensed, soine

water inay drip fl'oin the chute.

{{{{{{The first glass of water dispensed may

be wariner than the following ones.

This is norinal.

Automatic Icemaker

A newly-installed refrigerator may take 12-24

hours tobegin making ice.

Tile iceinaker will produce seven cubes per r

cycle--approxitnately 15 cycles or more in

a 24-hour period, depending on fl'eezer

colnpartlnent tenlperature, i'OOlil

temperature, number of door openings

ealcl other use conditions.

Green

If tile refl'igerator is operated before tile

water connection is inade to tile iceinakei;

set the power switch to O (off).

When the refl'igerator has been connected

to the water supply, set the power switch to

! (on). Tile green light will come on.

Throw away the fit'st fldl bucket of ice.

Be sure nothing interferes with the sweep

of the feeler re'In.

When tile bin fills to tile level of tile feeler

aa'in, the iceinaker will stop producing ice.

It is normal for several cubes to bejoined

together.

Power

PowerLight FeelerArm

If ice is not used fl'equently, old ice cubes

will becoine cloudy, taste stale and shrMk.

After tile icemaker has been turned on

again, there will be a delay of about 45

illitlutes before tile iceinaker resumes

operations.

NOTE: In homes with lower-than-average

water pressure, you inay heaa" the icemaker

water valve cycle on several tithes when

inakitlg one batch of ice. Recommended

water pressure is 60psi.

Abouttheiceand water dispenser. ElectroluxUSA.com

SpillShelf

To Use the Dispenser

Select CubedIce [ , CrushedIce[],

or Water [.

Press the glass gemly agahlst the middle

of the dispenser pad,

The spill shelf is not self-dran_ing.

To reduce water spottn_g, the shelf and

its grille should be cleaned regularly.

If no water N dispensed when the

refrigerator is first installed, there may be

Express Ice

DoorAlarm

When you need ice

h_ a hurry, press this

button to speed up ice

production. This will

h_crease ice production

for the following

48 houiB oi" until you

press the button agahl.

air in the water line system. Press the

dispenser arm for at least two minutes to

remove trapped air from the water line

and to fill the water system. Toflush out

impurities in the water line, throw away

the first six glassfuls of water.

k, CAUTION:Neverputfingers

or any other objects into the ice crusher

discharge opening.

Locking the Dispenser

Press the LOCK/LIGHT

button for 3 seconds

to lock the dispenser

eald control pealel. To

unlock, press and hold

the button again for

3 seconds.

To tun_ the Door Alea'in

on, press the DOOR

R/ARM button once.

The ACr/l/Elight will

come on. To turn it off,

press it agahl. When the

DOORALARM is active,

the ACrll/Elight will

flash if you open the

door fund beep if you

keep the door open for

inore thgu_ 2 mh_utes.

The light goes out fund

the beeping stops when

you close the dooi:

Dispenser Light

This button turns

the night light on the

dispenser 011and off.

The light also comes

on when the dispenser

pad is pressed. If this

light burl'lS out, it should

be replaced with a 6 watt

12V maximum bulb.

Careandcleaningoftherefrigerator.

Dispenser drip area,

Cleaning the Outside

The spill sheff and the area beneath it should

be cleaned perkxlically with a illild lklukl dish

deteigent.

Dispenserpad. Before clemling, lock

tile di.spenser by pressing tile LOCK/LIGHT

button fox"3 seconds to prevent activathlg

the di.spenser. Clean with warm water

eald a mild liquid dish deteigent. Rinse

thoroughly and wipe dry. Unlock the

dispenser by pressMg the LOgJ6q_IGHT

button for 3 seconds.

Doorhandles.Clean with a cloth deanpened

with soapy water. DU with a soft cloth.

Keeptheoutsideclean.Wipe with a clean

cloth lightly deanpened with inild liquid

dish detergent. Dry with a clean, soft cloth.

Do not wipe tile refl'igerator with a soiled

dish cloth oi" wet towel. These inay leave a

residue that can dainage the finish. Do not

use scouring pads, powdered cleaners,

bleach oi" cleaners containing bleach

because these products coal scratch and

dainage tile fintsh.

Stainless steel Regulea'ly cleeal and

polish the Stainless Steel Dooi_ with a

cominercially available stainless steel

clegulei'.

Do not use appliance wax oi" polish

on the stainless steel.

Cleaning the Inside

Turnoff power at the circuit breaker or fuse

box before cleaning. If tilts is not practical,

wI'ing excess moisture out of sponge oi"

cloth when cleealMg ea'ound switches, lights

oi" controls.

Use wealn water eald baking soda solution

about a tablespoon (15 ml) of baMng soda

to a quea't (1 liter) of water. This both

cleans and neutralizes odors. Thoroughly

rinse eald wipe dry.

Otherparts of the refrigerator,including door

gaskets, snack pan and vegetable drawei_,

ice storage bin and all plastic pea'ts, coal be

cleealed the saine way.

Do not wash the tray or any plastic

refl'igerator pea'ts in tile dtshwashei:

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them tobreak. Handle

glassshelves carefully. Bumpingtempered

glass can cause it toshatter.

ElectmluxUSA.com

Preparing for Vacation

For long vacations or absences, reinove

food guld tnlplug tile refrigerator. Cleeal tile

hlterior with a bakhlg soda solution of one

tablespoon (15 ml) of baking soda to one

quea't (1 liter) of water. Leave the dooI3

open.

Set the iceinaker power switch to the 0 (ofO

position guld shut off the water supply to

tile refl'igerator.

If tile teinperature can drop below fl'eezing,

have a qualified servicer drain tile water

supply system to prevent serious property

deanage due to flooding.

Preparing to Move

Secure all loose items such as shelves ealct

drawers by taping them securely in place

to prevent damage.

CAUTION:Due tothe weight

andsizeofthisrefrigerator,andtoreducethe

riskofpersonalinjuryordamagetothe

produc_AMINIMUM OF4PEOPLEARE

REQUIREDTOBRINGTHEUNITINTOTHE

HOMEAND2 PEOPLEAREREQUIREDFOR

PROPERINSTALLATION.

Besuretheretrigerotorstoysin onup@t

positionduringmoving.

Replacingthelightbulbs.

Setting the controls to OFF does not remove power to the light circuit.

Refrigerator Compartment--Upper Light

(appearance may vary)

O Raise the grille panel, set the master

power switch to the 0 (on) position eaK1

allow leanps to cool.

O To remove the light shield, press on the

Left side of the shieM and pull down.

O Replace the bulbs with appliance bulbs

of the saine or lower wattage. Replace

the shield by engaging the bottoin tab

into the slot guld applyh_g light forward

pressure until the shield snaps hi place.

Set the master power switch to the ](on)

position and close the grille pealel.

Refrigerator Compartment--Lower Light

Thislight is located above the top draweL

Raise the grille panel, set the master

power switch to the 0 (off) position and

allow lmnps to cool.

Remove iteins fl'om the shelf above the

light shield. Remove the shelf.

Use both hgu_ds to grasp each end of

the light shield. Press h_ on the bottom

of the shield with your thuInbs while

rotating the cover up guld out.

Replace the bulb with ea_appliealce

bulb of the saine or lower wattage.

Replace the shield by engaging the

bottom tab into the slot and applying

light forward pressure until the shield

snaps hi place.

Set the master power switch to the ](on)

position and close the grille panel.

Freezer Compartment

Raise the grille pgu_el, set the master

power switch to the 0 (off) position eald

allow lamps to cool.

Remove the iteins fl'oin the shelf just

below the light sh>ld. Reinove the

shelf.

To remove the light shield, press clown

on the top of the shield and pull the

tabs out of the slots. Tilt the shield

forward eaKl out.

Replace the bulb with an appliance

bulb of the same or lower wattage,

and reinstall the light shield. Replace

the shield by engaging the bottom tab

into the slot eald applyh_g light forward

pressure until the shield snaps hi place.

Set the master power switch to the ](on)

position and close the grille pealel.

Dispenser

O Raise the grille pgu_el, set the master

power switch to the 0 (off) position eald

allow lamps to cool.

The bulb is located in the dispenser

under the control panel. Remove the

two screws fl'om the light shield. Slide

the light shield toward the dispenser to

disengage the tabs, then remove the

light shield. Remove the light bulb by

turning it counterclockwise.

Replace the bulb with a bulb of the

same size and wattage. Replace the

light shield by sliding the tabs into

the slots in the front of the dispenser.

Replace the two screws.

Set the master power switch to the I(on)

position and close the grille pealel.

Installation

Instructions

Built-In Side-By-Side

Refrigerators

I If you have questions, call 1-877-4ELECTROLUX 877-435-3287 or visit our website at: I

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions for the consumer's and local

inspector's use.

• Note to Consumer - Keep these instructions

with your Owner's Manual for future reference.

• Skill Level - Installation of this refrigerator

requires basic mechanical, carpentry and

plumbing skills. Proper installation is the

responsibility of the installer, Product failure

due to improper installation is not covered

under the Electrolux Home Products

Warranty. See warranty information,

• Completion Time - 90 minutes (new

installations require more time than

replacement installations).

%2/-

CAUTION:

Due to the weight and size of this refrigerator,

and to reduce the risk of personal injury or

damage to the product, A MINIMUM OF 4

PEOPLE ARE REQUIRED TO BRING THE UNIT

INTO THE HOME AND 2 PEOPLE ARE

REQUIRED FOR PROPER INSTALLATION.

WARNING:

• These refrigerators are top-heavy and must

be secured to prevent the possibility of

tipping forward. Anti-Tip protection is

required. See Step 4 on page 30 for details,

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric power

supply cords that become frayed or damaged,

• Set the Master Power switch to the

O (OFF) position before cleaning or making

repairs,

• Repairs should be made by a qualified

service technician.

For local service in your area, call

1-877-4ELECTROLUX or 877-435-3287

For parts and accessories, call

1-877-4ELECTROLUX or 877-435-3287

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Instructions

HARDWARE SUPPLIED

• Anti-Tip brackets

Anti-Tip Brackets

MATERIALS REQUIRED

• 36" long, 2" x 4" wood block for Anti-Tip

bracket installation

• #12 or #14 wood screws for Anti-Tip bracket

• Screws to secure refrigerator to cabinets

• 1/4" O.D. copper water line tubing.

• Water shutoff valve

• Custom panels for doors and grille panel

(if installing custom panels)

• Special 3M Dual Lock adhesive strips for

1/4" side panels (if installing side panels)

3B" Wood Block

WaterShutoffValve

1/4" 0.D.CopperWater Line

Tubing

#12or #14

WoodScrews

Screws

Special 3M Dual Lock

Adhesive Strips

Custom Panels

TOOLS REQUIRED

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance dolly

• Tubing cutter

• Flathead screwdriver

• 1/2"open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 7/32", 1/2" sockets

• Safety glasses

• 7/16" open-end wrench

• Pliers

Appliance Dolly

Stepladder

Drill& Bits

SaFetyGlasses

FlatheadScrewdriver

PhillipsHead

Screwdriver

Sockets

Open-endWrenches

Tubing Cutter

Level

Bucket

Pliers

Tinsnips

Installation Instructions

THE INSTALLATION SPACE

_ Finished Width

74"

FromFloor

to Bottom

0fElectrical

*The finished cutout width must be:

41-1/2" for 42" models

Water and Electrical Locations

The opening must be prepared with the

electrical and water supply located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slightly

beyond adjacent cabinets, depending on

your installation.

Additional Specifications

• A 120 volt, 60Hz, 15 or 20 amp power

supply is required. An individual properly

grounded branch circuit or circuit breaker

is recommended. Install a properly

grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must

be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not

recommended.

Water line can enter the opening through

the floor or rear wall. The water line

installed should be 1/4" O.D. copper tubing

between the cold water line and water

connection location. The line should be

long enough to extend to the front of the

refrigerator. Installation of an easily

accessible shutoff valve in the water line is

required.

DIMENSIONS AND CLEARANCES

25-3/8" Case Depth

"81-3/

atRe_

*Shipping height

The front height

maybe adjusted

from 83-1/2"to 84-1/2"

byadjusting front and

rear leveling legsa

maximumof 1".

Depth Including

Handles26-7/8"

Product Clearances

These refrigerators are equipped with a 2

position door stop. The factory set 130 ° door

swing can be adjusted to 90 ° if clearance to

adjacent cabinets or walls is restricted.

130 ° Door Swing 90 ° Door Swing

/ Behind

Flame

x _JL iI'T

"... ,/ i.Dj J

_D4

Models A B C D

42" 12-3/16" 16" 24" 4"

Allow minimum clearances for Freezer

door (Dimension A) and Fresh Food door

(Dimension B) for a full 130 ° door swing

and to allow for drawer removal.

Four inch (4") minimum clearance is required

when door swing is adjusted to 90 °. If the 90 °

door stop position is used, drawer access is

maintained, but drawer removal is restricted.

See illustrations, pages 18 and 19, to

determine door swing interaction with

adjacent cabinets or countertops.

Installation Instructions

Refrigerator r23_7/8 ,,From

i i Rearof

z_:E_ Refrigerat°r

Case

|lr!m

1/2"

1/4"

3/4"CustomPanel

(NominalSize)

FreshFood

Door

BackerPane

Top View

130 ° Door Swing

(factory setting)

Scale 1:1

Installation Instructions

Refrigerator

Top View

90 ° Door Swing

(optional setting)

Scale 1:1

FreshFood

Door

CaseTrim

23-7/8"

FromRearof

Refrkerator

Installation Instructions

CUSTOMIZATION BASICS:

Stainless Steel Wrapped Models

Stainless Steel Wrapped Refrigerators

Stainless Steel wrapped refrigerators have

wrapped doors and grille panels, and beveled

edges. These models are shipped ready for

installation.

Trimmed Models

3/4" Framed Custom Panels

3/4" framed custom panels are secured

to a 1/4" finished backer panel. They are

designed to slide into the factory installed

trim, no kits required. The backer panel

will be exposed on the handle side and

therefore must be finished.

Trimmed Refrigerator Panels

Trimmed refrigerators are designed to be

customized with decorative panels. Field

installed custom door and grille panels are

required. There are three custom panel

options. You can install a 1/4" framed panel,

a 3/4" framed custom panel or a 3/4" full-

width overlay custom panel.

1/4" Framed Panels

You may install 114" thick custom panels from

your cabinet manufacturer. The decorative

panel slides into the factory installed trim.

DoorHandles

3/4" Full-Width Overlay Custom Panels

3/4" full-width overlay custom panels are

designed to slide into the factory installed

trim, no kits required. In this design, you

can achieve a nearly trimless appearance. A

spacer panel must be installed between the

finished backer and appearance panel. The

backer panel will be exposed on the handle

side and therefore must be finished.

FramedPanel _/

DoorHandles

1/4" Thick Backer PaneF

Door Handles On Trimmed Refrigerators

The handles can be used to accommodate

both framed or custom panels.

NOTE: For 3/4" custom panels, please refer

to diagrams on page 23 for optimum handle

clearance.

Page is loading ...

Electrolux E42BS75EPS Owner's manual

Brand: Electrolux

Model: E42BS75EPS

Category: Fridges

Type: Owner's manual

This manual is also suitable for

E42BS75ETT

Download PDF

report

Electrolux E42BS75EPS Owner's manual

This manual is also suitable for

Electrolux E42BS75EPS Owner's manual

Related papers

Other documents