Halsey Taylor OVL_EBP_SBP_SEBP_FR Owner's manual

Brand: Halsey Taylor

Model: OVL_EBP_SBP_SEBP_FR

Type: Owner's manual

97811C (Rev. F - 9/10)PAGE 1

OVLEBPFR, OVLSBPFR, OVLSEBPFR

Halsey Taylor Owners Manual

Non-Refrigerated Freeze Resistant Fountains

Halsey Taylor Fountains are among the easiest to install Fountains on the market today.

To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE

INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-

TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE

CODES. After installation, leave these instructions with the Fountain for future

reference. This Freeze Resistant Fountain(s) is shipped in two separate cartons. The

second carton(s) contains the Freeze Resistant Package(s) HTFRB1 that are installed

on an interior heated wall. The interior space must maintain a minimum temperature of

50° F (10° C). Refer to the Freeze Resistant Package for the rough-in dimensions for

installation.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

OVLEBPFR

OVLSBPFR

OVLSEBPFR

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES

IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN

ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE

WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN

FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE

FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

Installer

97811C (Rev. F - 9/10) PAGE 2

OVLEBPFR, OVLSBPFR, OVLSEBPFR

OVL - EBPFR/SBPFR/SEBPFR COOLER INSTALLATION

The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior

heated area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess

mounted the surface of the cover must be flush with the interior wall surface. The package is furnished with screws for

mounting the cover to the box. If the box is recess mounted, do not fasten the top and bottom of the cover to the box. Use the

holes on the front only.

1. Fountains using the MPW Mounting Plate refer to Fig's. 7, 8, 9, or 10 for hanger bracket location and rough-in dimensions.

NOTE: Review separate installation instructions for details of the MPW Mounting Plate.

Fountains using the Wall Plate Assy. refer to Fig's. 1, 2, 3, 4, 5, or 6 for rough-in dimensions.

2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight for single fountain and

300 lbs. for dual fountains). These dimensions are required for compliance with ANSI Standard A117.0.

3. Installing back panel.

Ftn. w/MPW Mounting Plate: Refer to Fig. 15 for placement of braces onto back panel. Place the upper edge of the panel

above hanger bracket. Slide the panel down until it engages the hanger bracket. Be sure back panel is firmly engaged

before releasing it.

Ftn. w/Wall Plate Assy.: Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it

engages the hanger. Be sure back panel is firmly engaged before releasing it.

4. Remove bottom access panel from fountain basin and save the screws.

Ftn. w/MPW Mounting Plate: Install the fountain to the back panel and wall using (4) 5/16 “ x 6” long threaded rods,

washers, and nuts (provided). Tighten securely.

Ftn. w/Wall Plate Assy.: Install the fountain to the back panel and wall using (4) 5/16" x 3/4" long bolts and washers

(provided) thru holes in back panel. A washer is used on the bottom two (2) holes only. Tighten securely.

5. Assemble the operating cable to the fountain bracket. (Fountain should be mounted to exterior wall) Create a loop in the

cable and thread the free end of the cable through the wall into the freeze resistant box. The adjustment nuts should be in

the middle of threaded area on the operating cable. See Figure 11.

6. Connect free end of operating cable to the valve-operating bracket. The end of the cables must be recessed into the

indents on the pivot brackets. Remove cable free play by adjusting the jam nuts on the ends of the operating cable.

See Figure 11.

7. Connect water line from fountain bubbler into freeze resistant box. The connection to the box uses a quick connect water

fitting. Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing, in the

exterior line, can freeze . See Fig. 18.

To insert tubing, push tube straight into fitting until it reaches a positive stop. To remove tubing from the fittings, relieve

water pressure, push in on dark gray collar while pulling out on the tubing. See Figure 17.

8. Connect drain and water supply lines to the freeze resistant fountain. Refer to Figure's 1 thru 10 for component positions.

Inline strainer must be used on the inlet water line. See Fig. 16.

Start-up

1. Turn on building water supply and check all connections for leaks. Repair as required.

2. Stream height is factory set at 35 PSI. If stream height (See Fig. 19) needs to be changed adjust the regulator in the freeze

resistant package. Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.

3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve

operation. If the system is too tight the valve will stay in the on position creating constant water flow. Too much free play will

result in non-operation of the valve with the push-buttons.

4. Note: Water from the drain back tube in the freeze resistant package, will continue to run while the valve is actuated.

5. After cable system is adjusted properly stuff flexible insulation into any openings between the outside wall and the

interior box.

6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).

97811C (Rev. F - 9/10)PAGE 3

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 1

FIG. 2

TOP VIEW ROUGH-IN FOR OVL-SBPFR/OVL-EBP-FR

97811C (Rev. F - 9/10) PAGE 4

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 3

LEGEND:

A = 1-1/4" O.D. Waste Tube (Trap And Elbow Provided)

B = 1/4" O.D. Freeze Resistant Cable

C = 1/4" O.D. Plastic Tube (Bubbler Water Supply)

D = 1/4" (6mm) DIA. Holes For Mounting Plate To Wall

ROUGH-IN FOR OVL-EBPFR

13 1/4"

337mm

14 1/4"

362mm

17 3/4"

451mm

28 11/16"

728mm

2 5/8"

67mm

3 5/8"

92mm

12"

305mm

MAX. WALL

THICKNESS

7 1/16"

180mm

5/8"

16mm

17 7/8"

454mm

FINISHED FLOOR

28 11/16"

728mm

25 3/4"

654mm

43 5/8"

1108mm

152mm

16"

406mm

5 1/4"

133mm

5 1/4"

133mm

203mm

1/2"

13mm

25mm

3/8" DIA. (10)

10mm

"B"

"A"

BACK PANEL

WALL PLATE

ASSEMBLY

"D"

1 1/4"

32mm

"C"

2" X 3-1/2" SLOT

FOR A, B, & C

- STUDS REQUIRED

FOR FRAME WALL

CONSTRUCTION

203mm

97811C (Rev. F - 9/10)PAGE 5

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 4

LEGEND:

A = 1-1/4" O.D. Waste Tube (Trap And Elbow Provided)

B = 1/4" O.D. Freeze Resistant Cable

C = 1/4" O.D. Plastic Tube (Bubbler Water Supply)

D = 1/4" (6mm) DIA. Holes For Mounting Plate To Wall

ROUGH-IN FOR OVL-SBPFR

33"

838mm

7 1/16"

180mm

12"

305mm

MAX. WALL

THICKNESS

2 5/8"

67mm

3 5/8"

92mm

20 1/4"

514mm

23 3/4"

603mm

19 1/4"

489mm

34 11/16"

880mm

FINISHED FLOOR

5/8"

16mm

13 3/16"

335mm

31 7/8"

810mm

34 11/16"

881mm

43 5/8"

1108mm

25mm

1/2"

13mm

5 1/4"

133mm

5 1/4"

133mm

203mm

1 1/4"

32mm

152mm

16"

406mm

- STUDS REQUIRED

FOR FRAME WALL

CONSTRUCTION

BACK PANEL

WALL PLATE

ASSEMBLY

"A"

"B"

"C"

"D"

2" X 3-1/2" SLOT

FOR A, B, & C

97811C (Rev. F - 9/10) PAGE 6

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 5

TOP VIEW ROUGH-IN FOR OVL-SEBPFR

97811C (Rev. F - 9/10)PAGE 7

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 6

LEGEND:

A = 1-1/4" O.D. Waste Tube (Trap And Elbow Provided)

B = 1/4" O.D. Freeze Resistant Cable

C = 1/4" O.D. Plastic Tube (Bubbler Water Supply)

D = 1/4" (6mm) DIA. Holes For Mounting Plate To Wall

ROUGH-IN FOR OVL-SEBPFR

5/8"

16mm

13 3/16"

335mm

17 7/8"

454mm

2 5/8"

67mm

3 5/8"

92mm

12"

305mm

MAX. WALL

THICKNESS

FINISHED FLOOR

27"

686mm

ADA

REQUIREMENT

7 1/16"

179mm

33"

837mm

14 1/4"

362mm

13 1/4"

337mm

17 3/4"

451mm

20 1/4"

514mm

23 3/4"

603mm

28 11/16"

729mm

34 11/16"

881mm

- STUDS REQUIRED

FOR FRAME WALL

CONSTRUCTION

5 1/4"

133mm

5 1/4"

133mm

5 1/4"

133mm

5 1/4"

133mm

203mm

16"

406mm

16"

406mm

1/2"

13mm

1/2"

13mm

25mm

1 1/4"

32mm

25mm

1 1/4"

32mm

2 3/4"

70mm

18 3/4"

476mm

2" X 3-1/2" SLOT

FOR A,B, & C (2)

"A"

"B"

"C"

"D"

WALL PLATE

ASSEMBLY

31 7/8"

810mm

152mm

34 11/16"

881mm

25 3/4"

654mm

152mm

28 11/16"

729mm

43 5/8"

1108mm

BACK PANEL

97811C (Rev. F - 9/10) PAGE 8

OVLEBPFR, OVLSBPFR, OVLSEBPFR

7 1/4"

184mm

12 1/8"

307mm

12"

305mm

MAX. WALL

THICKNESS

TOP VIEW ROUGH-IN FOR OVL-EBPFR WITH MPW100 MOUNTING PLATE

FIG. 7

97811C (Rev. F - 9/10)PAGE 9

OVLEBPFR, OVLSBPFR, OVLSEBPFR

43 7/8"

1114mm

28 11/16"

729mm

25mm

1 1/4"

32mm

1/2"

13mm

1 7/8"

47mm

203mm

16"

406mm

203mm

MPW100

MTG. PLT.

HANGER

BRACKET

BACK

PANEL

FINISHED FLOOR

LEGEND:

A = 1-1/4" O.D. Waste Tube (Trap And Elbow Provided)

B = 1/4" O.D. Freeze Resistant Cable

C = 1/4" O.D. Plastic Tube (Bubbler Water Supply)

D = 3/8" (10mm) DIA. Holes For Mounting Hanger Bracket To Wall

ROUGH-IN FOR OVL-EBPFR WITH MPW100 MOUNTING PLATE

FIG. 8

28 11/16"

728mm

27"

686mm

ADA

REQUIREMENT

7 1/16"

180mm

13 1/4"

337mm

12"

305mm

MAX. WALL

THICKNESS

5/8"

16mm

17 7/8"

454mm

FINISHED FLOOR

14 1/4"

362mm

17 3/4"

451mm

2 5/8"

66mm

3 5/8"

91mm

MPW100 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

FINISHED WALL

97811C (Rev. F - 9/10) PAGE 10

OVLEBPFR, OVLSBPFR, OVLSEBPFR

7 1/4"

184mm

12 1/8"

307mm

7 1/4"

184mm

12 1/8"

307mm

12"

305mm

MAX. WALL

THICKNESS

TOP VIEW ROUGH-IN FOR OVL-SEBPFR WITH MPW200 MOUNTING PLATE

FIG. 9

97811C (Rev. F - 9/10)PAGE 11

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FINISHED FLOOR

28 11/16"

729mm

34 11/16"

881mm

43 7/8"

1114mm

3 1/4"

82mm

16"

406mm

32"

813mm

6 5/8"

168mm

18 3/4"

476mm

25mm

1 1/4"

32mm

1 1/4"

32mm

25mm

HANGER BRACKET

BACK PANEL

MPW200

MTG. PLT.

1/2"

13mm

1/2"

13mm

LEGEND:

A = 1-1/4" O.D. Waste Tube (Trap And Elbow Provided)

B = 1/4" O.D. Freeze Resistant Cable

C = 1/4" O.D. Plastic Tube (Bubbler Water Supply)

D = 3/8" (10mm) DIA. Holes For Mounting Hanger Bracket To Wall

ROUGH-IN FOR OVL-SEBPFR WITH MPW200 MOUNTING PLATE

FIG. 10

FINISHED FLOOR

12"

305mm

MAX. WALL

THICKNESS

5/8"

16mm

13 3/16"

335mm

17 7/8"

454mm

28 11/16"

728mm

33"

838mm

14 1/4"

362mm

13 1/4"

337mm

17 3/4"

451mm

34 11/16"

881mm

20 1/4"

515mm

23 3/4"

604mm

27"

686mm

ADA

REQUIREMENT

7 1/16"

180mm

2 5/8"

66mm

3 5/8"

91mm

MPW200 MTG. PLT.

REF. SEPARATE

INSTALLATION

INSTRUCTIONS

FOR DETAILS

FINISHED WALL

97811C (Rev. F - 9/10) PAGE 12

OVLEBPFR, OVLSBPFR, OVLSEBPFR

CABLE SHEATH ADJUSTMENT

To Increase Free Play

To Reduce Free Play

FIG. 11

FIG. 12

FIG. 13

97811C (Rev. F - 9/10)PAGE 13

OVLEBPFR, OVLSBPFR, OVLSEBPFR

OPERATION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN

TUBE TO ATTACH

TUBE IS SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE.

1/4" O.D. TUBE

WATER INLET

NOTE: WATER FLOW DIRECTION

BUILDING WATER

INLET

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

SERVICE STOP

(NOT FURNISHED)

FIG. 14

FIG. 17

FIG. 16

SEE FIG. 8

SEE FIG. 9

Installing Back Panel: When installing back panel

assy. (Item 32) with MPW (Mounting Plate), attach

channel braces as shown above. Remove the

protective backing from the tape installed on the

braces. Line up the corresponding holes in the

braces and back panel and press firmly in place.

FIG. 15

97811C (Rev. F - 9/10) PAGE 14

OVLEBPFR, OVLSBPFR, OVLSEBPFR

FIG. 18

14, 15

97811C (Rev. F - 9/10)PAGE 15

OVLEBPFR, OVLSBPFR, OVLSEBPFR

DESCRIPTION

27688C

27689C

50595C

51546C

100322740560

160270508640

101570540560

51575C

110346220550

101637451550

161637308640

15008C

100023340560

161570808550

45663C

75672C

27006C

27000C

112627543890

55919C

45662C

55001138

55001139

27945C

27946C

40045C

40206000

56092C

70425C

50198C

51667C

22797C

22799C

26958C

28120C

28121C

28168C

28838C

28811C

27089C

27090C

45730C

75541C

111577243890

PART NO.

Bottom Cover (OVL-S)

Bottom Cover (OVL-E)

Bushing - Snap

Bubbler

Gasket - Black

Strainer Plate

Drain Gasket

Packing Ring

Lock Nut - 1-1/2"-11-1/2

Friction Ring

Drain Plug

Bubbler Nipple Assembly

Gasket - Neoprene

Slip Nut

Push Button Sleeve

Screw - Cap

Basin

Basin Liner

Screw # 10-24 x 1/2" Long

Push Button Extension

Push Button

Arm (OVL-S-FR)

Arm (OVL-E-FR)

Basin Bracket

Basin Pivot Bracket

Nut - Hex (unplated)

Retainer

Tube - Poly (cut to length)

Rod - Pivot

Bushing Snap

Bumper - Reg. Valve Assy

Back Panel (OVL-EBP)

Back Panel (OVL-SBP)

Back Panel (OVL-SEBP)

Wall Plate Assembly - OVL-SBP

Wall Plate Assembly - OVL-SEBP

Wall Plate Assembly - OVL-EBP

Back Panel Assembly - OVL-EBP

Back Panel Assembly - OVL-SEBP

Hanger Bracket - OVL-EBP

Hanger Bracket - OVL-SEBP

Drain Tube

Washer-Flat .339/.359ID Steel

Screw-Mach. 5/16-18 x 3/4" Long

ITEM NO.

PARTS LIST

2222 CAMDEN COURT

OAK BROOK, IL 60523

630.574.3500

PRINTED IN U.S.A.

TROUBLE SHOOTING AND MAINTENANCE

Orifice Assy: Mineral deposits on orifice can cause water flow

to spurt or not regulate. Mineral deposits may be removed

from the orifice with a small round file or small diameter wire.

CAUTION: DO NOT file or cut orifice material.

Stream Regulator: If orifice is clean, regulate flow as in

“STREAM HEIGHT ADJUSTMENT” instructions on page 2. If

replacement is necessary, see parts list for correct regulator

part number.

Actuation of Quick Connect Water Fittings: Fountain is

provided with lead-free connectors which utilize an o-ring water

seal. To remove tubing from the fitting, relieve water pressure,

push in on the gray collar while pulling on the tubing.

(See Fig.17) To insert tubing, push tube straight into fitting until

it reaches a positive stop, approximately 3/4".

FIG. 19

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM

Halsey Taylor OVL_EBP_SBP_SEBP_FR Owner's manual

Halsey Taylor OVL_EBP_SBP_SEBP_FR Owner's manual

Halsey Taylor OVL_EBP_SBP_SEBP_FR Owner's manual

Related papers

Other documents