Edge ED305 User manual

Edge
Brand
Edge
Model
ED305
Type
User manual

This manual is also suitable for

INTRODUCTION
This instruction manual is for your safety and must be adhered to at all times. Please read and
ensure that you fully understand the installation and set up procedures as explained. If you
are unclear on the installation or set up of your EDGE speakers please contact your nearest
authorised EDGE dealer.
Contents
2 x EDGE woofers
2 x EDGE tweeters
2 x EDGE crossovers
2 x woofer grills.
8 x Fixing screws.
1 x Cut out template.
2 x Lengths of speaker cable.
Warranty card
WARNING
DO NOT EXPOSE THIS PRODUCT TO DAMP OR MOISTURE - doing so may result in re,
shock or damage to the product.
BEFORE WIRING DISCONNECT THE CABLE FROM THE POSITIVE BATTERY TERMINAL -
failure to do so may result in electric shock or injury.
ENSURE GOOD AND CORRECT CONNECTIONS - failure to make the correct connections
may result in re or damage to the product.
DO NOT USE ANY FUNCTIONS OF THIS EQUIPMENT THAT MAY TAKE YOUR
CONCENTRATION AWAY FROM DRIVING YOUR VEHICLE - do not set up your amplier
whilst driving, doing so may result in an accident. For prolonged setting up, make sure that
your vehicle is stationary and in a safe location.
KEEP THE VOLUME AT A LEVEL SO YOU CAN STILL HEAR OUTSIDE NOISE - failure to do
this may result in an accident. EDGE equipment is capable of producing sound levels that can
permanently damage your hearing. EDGE recommends caution when listening at high volume.
For safe and enjoyable listening the sound should be comfortable and clear without distortion.
CAUTION
Never connect any speaker lead to the car chassis. This can cause severe damage to your
speaker /car radio /amplier.
Before drilling or cutting any holes, investigate the layout of your vehicle thoroughly.
Use caution when working near the fuel / hydraulic lines and electrical wiring.
Observe the correct polarity when wiring, improper phasing may cause a loss of bass
response.
Ensure that no moving parts catch on the speaker or grill (e.g. window or door handles, or
window glass inside the door)
Woofer Installation
Using the template provided nd a suitable mounting location
for the woofer.
Mark the mounting holes and pre drill the xing hole with a
2mm drill bit. If the grill is too be tted then place it over the
speaker and screw through both the grill and the speaker
using the provided screws. Be careful not to over tighten the
screws as it may cause the grill to break.
Tweeter Installation Guidelines
The tweeter can either be tted ush mount or surface
mount. Try and take into account the following when locating
a suitable position. For optimum staging try and locate a
position that is higher than the woofer but within twelve inches (maximum) of it.
It is vital that the tweeter is adjusted so that it is focused towards the listener.
Surface Mount Tweeter Installation
After nding a suitable position for the tweeters place the base of the tweeter casing in the
correct position.
Using this base mark the two mounting holes and the hole for the wire to pass through.
Cut out these holes using a 2mm drill for the xing screws and at least an 8mm hole for the
cable, ensure that the hole cut for the cable is big enough and will not cause the cable to
become chaffed in any way.
Pass the tweeter cable through the bottom of the case and through the previously drilled hole.
Secure the bass of the tweeter housing with the screws provided.
Finally, angle the tweeter so that it is focused towards the listener.
CROSSOVER
CROSSOVER
CROSSOVER
CROSSOVER
Flush Mount Tweeter Installation
For ease of installation there are two ways of xing the tweeters in place.
The rst requires the use of the metal ring provided. (See Figure A)
After nding a suitable position for the tweeters place the cut out template for the tweeter in
position and mark around it.
Before cutting the holes double check that no brake, fuel lines or wiring harnesses are likely to
get damaged.
Ensure that the tweeter when tted will not catch on any moving parts such as door / window
handles.
If mounting in a door check that the window can still be fully lowered before installing.
Cut out the hole carefully.
Place the entire tweeter into the cut out hole.
From the back push the metal ring over the rear of the casing until it is tight into the hole.
The second requires the use of the metal strip provided. (See Figure B)
After nding a suitable position for the tweeters place the cut out template for the tweeter in
position and mark around it.
Before cutting the holes double check that no brake, fuel lines or wiring harnesses are likely
to get damaged.
Ensure that the tweeter when tted will not catch on any moving parts such as door / window
handles.
If mounting in a door check that the window can still be fully lowered before installing.
Cut out the hole carefully.
Position the metal strip xing strip centrally, behind the cut out hole.
Using the xing screws attach the base of the tweeter case to the metal strip.
Pass the tweeter cable through the hole in the centre in the bottom of the case and the metal
xing strip.
Pull the cable tight until the tweeter sits in the base.
Screw the top of the tweeter casing to the base.
Caution do not over tighten.
Wiring Examples
Model ED204 ED205 ED206 ED209
Type Coaxial Coaxial Coaxial Coaxial
Configuration 4 way 4 way 4 way 4 way
Speaker size 4” (100mm) 5.25” (130mm) 6.5” (165mm) 6x9” (150 x 220mm)
RMS power 40 watts 50 watts 60 watts 100 watts
Peak power 120 watts 150 watts 180 watts 300 watts
Minimum input 20 wRMS 25 wRMS 30 wRMS 50 wRMS
Sensitivity 83.9dB 86.2dB 86.2dB 86.1 dB
Frequency response 100Hz – 20KHz 80Hz – 20KHz 65hz – 20KHz 45Hz- 20KHz
Mounting depth 43mm 47mm 55mm 72mm
Mounting diameter 94mm 118mm 144mm 150x220mm
Recommended ED7400/7800 ED7400/7800 ED7400/7800 ED7400/7800
amplifier ED71600 ED71600 ED71600 ED71600
Model ED305 ED306
Type component component
Configuration 2 way 2 way
Speaker size 5.25” (130mm) 6.5” (165mm)
RMS power 70 watts 80 watts
Peak power 210 watts 240 watts
Minimum input 35 watts RMS 40 watts RMS
Sensitivity 91dB 91dB
Frequency response 80Hz – 20KHz 65hz – 20KHz
Mounting depth 54mm 57mm
Mounting diameter 118mm 144mm
Recommended ED7400/7800 ED7400/7800
amplifier ED71600 ED71600
Model ED7400 ED7800 ED71600 ED71200 ED72500
Type 2/1 channel 4/3/2 channel 4/3/2 channel Monoblock Monoblock
Class AB AB AB D D
4 ohm stereo 2 x 75 watts RMS 4 x 75 watts RMS 4 x 120 watts RMS N/A N/A
2 ohm stereo 2 x 100 watts RMS 4 x 100 watts RMS 4 x 200 watts RMS N/A N/A
4 ohm mono 1 x 200 watts RMS 2 x 200 watts RMS 2 x 400 watts RMS 1 x 200 watts RMS 1 x 400 watts RMS
2 ohm mono N/A N/A N/A 1 x 400 watts RMS 1 x 800 watts RMS
1 ohm mono N/A N/A N/A 1 x 600 watts RMS 1 x 1250 watts RMS
Max power 400 watts 800 watts 1600 watts 1200 watts 2500 watts
Frequency respo 20Hz – 20KHZ 20Hz – 20KHz 20Hz – 20KHz 20Hz – 300Hz 20 Hz – 300Hz
Height 68mm 68mm 68mm 68mm 68mm
Width 225mm 325mm 445mm 330mm 405mm
Depth 244mm 244mm 244mm 244mm 244mm
Model ED510 ED512 ED515
Type subwoofer subwoofer subwoofer
Speaker size 10” (272mm) 12” (324mm) 15” (397mm)
RMS power 250 watts 300 watts 350 watts
Peak power 750 watts 900 watts 1050 watts
Minimum input 125 watts RMS 150 watts RMS 175 watts RMS
Sensitivity 89dB 90dB 90dB
Frequency response 30Hz - 1700Hz 25Hz – 1500KHz 20hz – 850Hz
Mounting diameter 235mm 285mm 350mm
Mounting depth 125mm 144mm 148mm
Voice coil 2 ohm DVC 2 ohm DVC 2 ohm DVC
Recommended ED71200/72500 ED71200/72500 ED71200/72500
amplifier ED7400/7800/71600 ED7400/7800/71600 ED7400/7800/71600
Model ED610 ED612 ED612T ED615
Driver ED510 ED512 2 x ED512 ED515
Enclosure impedance 1 or 4 Ohm 1 or 4 Ohm 1, 4 or 8 Ohm 1 or 4 Ohm
RMS power 250 watts 300 watts 600 watts 350 watts
Peak power 750 watts 900 watts 1800 watts 1050 watts
Recommended ED71200/72500/ ED71200/72500/ ED71200/72500/ ED71200/72500/
amplifier ED7400/7800/71600 ED7400/7800/71600 ED7400/7800/71600 ED7400/7800/71600
Model ED pack 10 ED pack 12
ED pack 12 twin
enclosure ED610 ED612 ED612T
amplifier ED7400 ED7400 ED71200
Speaker size 10” (272mm) 12” (324mm) 15” (397mm)
RMS power 250 watts 300 watts 600 watts
Peak power 750 watts 900 watts 1800 watts
Amplifier wiring kit 10AWG included 10AWG included 8AWG include
d
Model ED402 ED404 ED405 ED406 ED408
Type bullet tweeter bullet tweeter Midrange Midrange midrange
Configuration 1 way 1 way 1 way 1 way 1 way
Speaker size 2” (50mm) 4” (100mm) 5.25” (130mm) 6.5” (165mm) 8” (200mm)
RMS power 40 watts 50 watts 80 watts 300 watts 450 watts
Peak power 120 watts 150 watts 240 watts 100 watts 150 watts
Minimum input 20 watts RMS 25 watts RMS 40 watts RMS 50 watts RMS 75 watts RMS
Sensitivity 106dB 107dB 96dB 97dB 98dB
Frequency response 5KHz – 20KHz 4.5KHZ – 20KHz 80Hz – 6KHz 65hz – 6KHz 55Hz – 6KHz
Mounting diameter 43mm 90mm 114mm 146mm 183mm
Mounting depth 40mm 70mm 49mm 55mm 82mm
Recommended ED7400/7800/ ED7400/7800/ ED7400/7800/ ED7400/7800/ ED7400/7800/
amplifier ED71600 ED71600 ED71600 ED71600 ED71600
Model ED710 ED712 ED715 ED718
Type woofer woofer woofer woofer
Speaker size 10” (272mm) 12” (324mm) 15” (397mm) 18” (457mm)
RMS power 400 watts 500 watts 600 watts 900 watts
Peak power 1200 watts 1500 watts 1800 watts 2700 watts
Minimum input 200 watts RMS 150 watts RMS 300 watts RMS 450 watts
Sensitivity 97dB 98dB 99dB 02dB
Frequency response 30Hz – 5.5KHz 25Hz – 5.5KHz 20hz – 5KHz 15Hz – 5KHz
Mounting diameter 234mm 284mm 352mm 428mm
Mounting depth 113mm 130mm 128mm 186mm
Voice coil 2 ohm DVC 2 ohm DVC 2 ohm DVC 2 ohm DVC
Recommended ED71200/ED72500 ED71200/72500 ED71200/72500 ED71200/72500
amplifier ED7400/7800/71600 ED71600 ED71600 ED72500
Limited Warranty
All EDGE goods are covered by a full 12 months
manufacturers warranty. Valid from the date of the
original receipt and proof of purchase. In order to
validate this warranty, the warranty card should be
returned to EDGE within seven days of the original
purchase date. The original receipt and packaging
should also be kept for this 12 month period.
If at any stage during the warranty period you have a
problem with the product then it should be returned
to the point of purchase in its original packaging,
complete and with no items missing.
If the store is unable to x the product it may have
to be returned to EDGE this process takes around 7
working days.
A full description of EDGE’s warranty information
can be found on our website:
www.edgecaraudio.com/warranty
A written version can also be obtained from
EDGE warranty department
PO Box 11000
B75 7WG
Copyright
All content included in this manual such as text, graphics,
logos, icons, images data, the selection and arrangement
thereof, are the property of EDGE Audio (herein referred
to as “EDGE”, “us” or “we”) and its afliate or their
content and technology providers, and are protected by
United Kingdom and International copyright laws. All
rights reserved.
Trademarks
EDGE ED2
TM
, EDGE ED3
TM
, EDGE ED4
TM
, EDGE ED5
TM
EDGE ED6
TM
, EDGE ED7
TM
, EDGE Street
TM
and
EDGE Loud
TM
and all stylised representations of
product names, or the abbreviations of product names,
as logos are all trademarks of EDGE. Graphics and
logos are trademarks or trade dress of EDGE Audio or
its subsidiaries.
EDGE’s trademarks and trade dress may not be used in
connection with any product or service that is not EDGE’s,
in any manner that is likely to cause confusion among
customers or in any manner that disparages or discredits
EDGE. All other trademarks not owned by EDGE or its
subsidiaries that appear in this manual are the property
of their respective owners, who may or may not be
afliated with, connected to, or sponsored by EDGE or
its subsidiaries.
We reserve the right to make needed changes or
improvements to the produc and this manualt , without
informing the customer about this in advance
CROSSOVER
CROSSOVER
ED206 connected to ED901 CD/Tuner
ED209 connected to amplier (ED7400/
ED7800/ED71600)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Edge ED305 User manual

Edge
Brand
Edge
Model
ED305
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents