Sloan SG-7019 Installation guide

Brand: Sloan

Model: SG-7019

Type: Installation guide

WARNING: Risk of personal injury or product damage. Handle with care.

SKU Description M12 Rack Bolt M16 Rack Bolt Wall Bracket M12 Chair Bracket In Wall Tank frame

1213309-0 1223947-0 1224238-0 1225108-0 97504IN-NA

1213309-1CP-0 1223947-1CP-0

1213309-1BLM-0 1223947-1BLM-0

SKU Code

SG-7019

Compact Rear

Inlet Urinal

BEFORE YOU BEGIN

RECOMMENDED TOOLS AND MATERIALS:-

INSTALLATION INSTRUCTIONS

•Vitreous China can break or chip if the bolts and nuts are over-

tightened, or if the product is handled carelessly.

•Observe all local plumbing and building codes.

•Check for any damage to the new urinal before installation.

•Make sure the wall is strong enough to support the new urinal prior

to installation. Reinforce or install a urinal carrier if necessary.

√Minimum Flowing Pressure: 25 PSI

WARNING: hazardous gases can escape through the waste pipe

if new urinal is not installed quickly. A temporary fix: place a rag in

the waste pipe hole.

INSTALLATION GUIDELINE

Gasket

(Included)

Outlet Flange

(Included)

2” NPT

•

Remove the temporary rag (if used) from the

waste pipe hole.

•

Apply thread sealant to waste pipe threads

and install new outlet flange on pipe.

1. INSTALL OUTLET FLANGE AND GASKET

Silicone

•FOR BEST PERFORMANCE OF YOUR

SLOAN® URINAL, USE SLOAN®

TRUFLUSH FLUSHOMETERS

Rev-00 03-21

Code:08160021

SLOAN INDIA PRIVATE LIMTED

344, PHASE-II, UDYOG VIHAR, GURGAON 122015 Phone: (+91) 124-601333

Note:-All vitreous china dimensions shown in

these drawings are nominal. Dimensions can

vary within the tolerances established in the

governing BIS standard. Please take this into

consideration when planning rough-in and

plumbing layouts.

Product illustrations shown are representative

only; actual products may vary.

Sloan reserves the right to make changes in

product characteristics, packaging or

availability at any time without notice.

CAUTION : Do not use white cement or high

lime-content cement to install this toilet.

The expansion of cement due to rise in

temperature may cause the toilet to crack or

damage. Sloan is not responsible for any

damage due to installation with the use of

cement.

Inds

LIMITED WARRANTY

Sloan Valve Company warrants its vitreous china products to be made of first class materials, free from defects of material or workmanship under normal

use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period

of five years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus

defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be

allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s

products directly from Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HERE OF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR

ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER. NOTE: IN NO EVENT SHALL THE SLOAN VALVE COMPANY BE LIABLE FOR INCIDENTAL

DAMAGES, RESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE OR ALTERATION.

INSTALLATION GUIDELINE

2. INSTALL NEW WALL HANGER BRACKET (INCLUDED)

13 3/8”

(340 mm) 19”

(483mm)

11 5/8”

(295 mm)

18 3/8”

(467 mm)

24”

(610 mm)

14 3/4”

(375 mm)

Rubber Gasket

16 3/4”

(425mm)

•

Concrete Wall must be properly reinforced to support urinal.

•

Determine position for new wall hanger bracket and mark

hole locations.

•

Drill holes in wall (use wall anchors if needed).

•

Mount and level wall hanger bracket using mounting screws

and washers (included).

Hand tighten

hex acorn nut into

one end of each

bolt before carefully

securing and

tightening them

Note: Check if

urinal is level. If not,

adjust bracket.

CAUTION!

Do not

overtighten the

bolts. Breakage

and chipping of

vitreous china

can occur.

4. COMPLETING THE INSTALLATION

•Install flush valve(not included) to manufacturer’s installation

instructions.

•Turn on water supply valve.

•Flush urinal a few times and check all connections for water seepage.

•Use Silicon on urinal perimeter where urinal meets the wall surface to

provide a suitable hygienic seal.

5. CARE AND CLEANING OF VITREOUS CHINA:-

•Clean urinals with a cleaner safe for vitreous

china . Spray and wipe clean using soft cloth.

Soft abrasive cleaners may be used to remove

stains.

16.71” (424 mm)

Center to Center

Reinforced

wall framing/

urinal carrier

Holes

10 1/4”

(260 mm)

5”

(127 mm)

13 3/16”

(335 mm)

Rear water

supply inlet

4”

(102 mm)

12 1/2”

(317 mm)

3. INSTALL NEW URINAL

•

Install urinal on wall hanger bracket and secure bottom

of urinal with bolts.

13 3/8”

(340 mm) 19”

(483 mm)

5/8”11

(295 mm)

18 3/8”

mm)(467

24”

(610 mm)

14 3/4”

(375 mm)

3/4” Spud

16 3/4”

(425 mm)

•

With extended connector use only Rubber

Gasket

•

For flexible connection use 3/4" brass

connector which exist with product.

-2-

SLOAN INDIA PRIVATE LIMTED

344, PHASE-II, UDYOG VIHAR, GURGAON 122015 Phone: (+91) 124-601333

Outlet

Rev-00 03-21

Code:08160021

Note: Product illustrations shown are representative only; actual products may vary.

Sloan SG-7019 Installation guide

Sloan SG-7019 Installation guide

Sloan SG-7019 Installation guide

Related papers

Other documents