Mircom FA-103 Conventional Fire Alarm Control Panels User manual
- Category
- Fire protection
- Type
- User manual
Mircom FA-103 Conventional Fire Alarm Control Panels are designed to provide reliable and effective fire protection for a variety of applications. With three input circuits, two output circuits, and a dome switch design, the FA-103 is easy to use and install. The FA-103 also meets the latest ULC-S527-11 standard, ensuring that it provides the highest level of protection.
Some of the key features of the FA-103 include:
- Three input circuits for connecting smoke detectors, heat detectors, and other fire alarm devices
- Two output circuits for controlling fire alarm notification devices, such as horns, strobes, and bells
Mircom FA-103 Conventional Fire Alarm Control Panels are designed to provide reliable and effective fire protection for a variety of applications. With three input circuits, two output circuits, and a dome switch design, the FA-103 is easy to use and install. The FA-103 also meets the latest ULC-S527-11 standard, ensuring that it provides the highest level of protection.
Some of the key features of the FA-103 include:
- Three input circuits for connecting smoke detectors, heat detectors, and other fire alarm devices
- Two output circuits for controlling fire alarm notification devices, such as horns, strobes, and bells
Mircom Group of Companies
25 Interchange Way | Vaughan (Toronto) ON L4K 5W3 | T 905 660-4655 | F 905 660-4113 | www.mircom.com
PRODUCT INTRODUCTIONS
Conventional Fire Alarm Control Panels
FA-103 & FA-106
March 3, 2017
The Mircom Group of Companies is pleased to announce the introduction of four new
products to the FA-100 series of Conventional Fire Alarm Control Panels. Namely,
Three-Zone Fire Alarm Unit, FA-103, in beige
Three-Zone Fire Alarm Unit, FA-103R, in red
Six-Zone Fire Alarm Unit, FA-106, in beige
Six-Zone Fire Alarm Unit, FA-106R, in red
These four new products are being offered in order to meet the requirements of ULC-S527-
11 (3rd Edition) and ensure seamless supply of product. These new products hold a very
similar feature set to previous and now obsolete, FA-100 series lineup of products (including
FA-101T, FA-102T, FA-1025T and all variations) with several enhancements including:
Meeting ULC-S527-11 standard
Three (FA-103) and Six (FA-106) Input Circuits
Two Output Circuits
Dome Switches
New Printed Circuit Board (PCB)
All four new products can now be ordered with an estimated availability date of April 28,
2017.
For more information about these new products, please refer to the attached Frequently
Asked Questions (FAQ) and the Mircom website.
firealarmresources.com
FA-100 Series FAQ
2017
FA-100 Series FAQ, March 2017
2
#
Question
Answer
1
Why is the FA-100 Series changing?
New ‘Listing’ requirements drove our initiative to obsolete the old FA-100 Series line-up and replace it
with the new FA-103 and FA-106.
2
What is happening to the old FA-100 Series
products?
The old FA-100 Series products are now Obsolete. Our inventory will be sold until depleted.
3
Is the new FA-100 Series available in all
markets?
Our target markets for the FA-100 Series remain unchanged. It will continue to be available to the
Canadian and International markets.
4
Is the new FA-100 Series listed?
The new FA-100 Series meets the latest ULC -S527-11 standard.
5
Where can I get more product information
regarding the new FA-100 Series products?
Datasheets as well as Installation Manual are posted on the Mircom website:
https://www.mircom.com/product-listing/fire-alarm-detection/conventional-fire-alarm/fa-100-fire-
alarm-control-systems
6
What does the new FA-100 Series consist
of?
There are four Fire Control Alarm Panels as follows:
Three-Zone Fire Alarm Unit, FA-103, in beige
Three-Zone Fire Alarm Unit, FA-103R, in red
Six-Zone Fire Alarm Unit, FA-106, in beige
Six-Zone Fire Alarm Unit, FA-106R, in red
firealarmresources.com
FA-100 Series FAQ
2017
FA-100 Series FAQ, March 2017
3
7
What is the difference between the old and
new FA-100 Series:
This table summarizes the differences:
Feature
Old
New
Comments
Output
Total output of 1.7Amps
Total output of 2.0Amps (1.25
max per circuit)
Improvement
Construction
New PCB
Improvement
Construction
New Dead front
Improvement
Annunciator support
Remote Annunciator support
No Remote Annunciator support
Better supported by
other product(s)
Non-latching alarm
Non-latching alarm support
No non-latching alarm support
ULC requirement
ULC
Meets ULC-527-2011 standard
Meets
requirements
Switches
Slide switches
Dome switches
Improvement
Configuration
Configuration via jumper
Configuration via DIP switch
Improvement
Input Circuits
One (FA-101T), two (FA-
102T) and five (FA-1025T)
Three (FA-103) and six (FA-106)
Improvement
Output Circuits
One (FA-101T), One (FA-
102T) and two (FA-1025T)
Two (FA-103) and two (FA-106)
Improvement
8
When can I order the new FA-100 Series
products?
We will accept all new orders effective immediately. Estimated availability date is April 28, 2017.
firealarmresources.com
FA-100 Series FAQ
2017
FA-100 Series FAQ, March 2017
4
9
Is there a recommended ‘go-forward’
conversion model recommendation?
Yes, the following table is the ‘go-forward’ model conversion recommendation:
Old
New
FA-101T
FA-103
FA-1025T
FA-106
FA-1025T-RED
FA-106R
FA-102T
FA-103
FA-102T-RED
FA-103R
10
Whom do I contact for technical support or
inquiries?
Please continue to contact the Mircom Technical Support team toll-free at 1-888-647-2665.
firealarmresources.com
-
1
-
2
-
3
-
4
Mircom FA-103 Conventional Fire Alarm Control Panels User manual
- Category
- Fire protection
- Type
- User manual
Mircom FA-103 Conventional Fire Alarm Control Panels are designed to provide reliable and effective fire protection for a variety of applications. With three input circuits, two output circuits, and a dome switch design, the FA-103 is easy to use and install. The FA-103 also meets the latest ULC-S527-11 standard, ensuring that it provides the highest level of protection.
Some of the key features of the FA-103 include:
- Three input circuits for connecting smoke detectors, heat detectors, and other fire alarm devices
- Two output circuits for controlling fire alarm notification devices, such as horns, strobes, and bells
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Mircom LT-493 FA-1025T Operating instructions
-
-
-
-
Mircom LT-657 FX-2000 Operating instructions
-
-
-
-
-
