Black & Decker KS950SW Owner's manual

Page is loading ...

5

ENGLISH

English

Intended use

Your Black & Decker jigsaw has been designed for sawing

wood, plastics and sheet metal. This tool is intended for

consumer use only.

General safety rules

Warning! Read all safety warnings and all

instructions. Failure to follow all instructions may

result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR

FUTURE REFERENCE.

The term "power tool" in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered and dark

areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personal injury.

b. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

c. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invites accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

e. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of these devices

can reduce dust related hazards

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

!

6

ENGLISH

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Specific safety instructions for jigsaws

X Hold the tool by the insulated gripping surfaces when

performing an operation where the cutting tool may contact

hidden wiring or its own cord. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock the

operator.

X Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body leaves it unstable and may lead

to loss of control.

X Keep hands away from cutting area. Never reach

underneath the work piece any reason. Do not insert

fingers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

X Keep blades sharp. Dull or damaged blades may cause the

saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

X When cutting pipe or conduit, make sure that they are free

from water, electrical wiring, etc.

X Do not touch the workpiece or the blade immediately after

operating the tool. They can become very hot.

X Be aware of hidden hazards, before cutting into walls,

floors or ceilings, check for the location of wiring and pipes.

X The blade will continue to move after releasing the switch.

Always switch the tool off and wait for the saw blade to

come to a complete standstill before putting the tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specifically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

X This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Additional safety instructions for non-rechargeable

batteries

X Never attempt to open for any reason.

X Do not store in locations where the temperature may

exceed 40 °C.

X When disposing of batteries, follow the instructions given in

the section "Protecting the environment".

Do not incinerate the batteries.

X Under extreme conditions, battery leakage may occur.

When you notice liquid on the batteries, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin

contact.

Additional safety instructions for lasers

X This laser complies with class 2 according to IEC

60825+A1+A2:2001. Do not replace a laser diode with a

different type. If the laser is damaged, have the laser

repaired by an authorised repair agent.

X Do not use the laser for any purpose other than projecting

laser lines.

Read all of this manual carefully.

This product is not to be used by

children under 16.

Laser radiation.

Do not look into the laser beam.

Do not use optical tools to view the

laser beam.

7

ENGLISH

X An exposure of the eye to the beam of a class 2 laser is

considered safe for a maximum of 0.25 seconds. Eyelid

reflexes will normally provide adequate protection. At

distances greater than 1m, the laser complies with class 1

and is therefore considered completely safe.

X Never look into the laser beam directly and intentionally.

X Do not use optical tools to view the laser beam.

X Do not set up the tool where the laser beam can cross any

person at head height.

X Do not let children come near the laser.

Features

1. Lock-on button

2. On/off switch

3. Blade storage compartment cover

4. Shoe plate locking lever

5. Dust extraction outlet

6. Dust extraction adaptor

7. Shoe plate

8. Auto Select

TM

dial

9. Blade support roller

10. Tool-free blade clamp

Additional features (fig. A)

Additional features may be applicable depending upon the

product purchased. The additional features applicable to the

catalogue number purchased are shown in fig. A.

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and

that the saw blade has stopped. Used saw blades may be

hot.

Fitting the saw blade (fig. B)

X Hold the saw blade (11) as shown, with the teeth facing

forward.

X Push and hold the blade clamp (10) down.

X Insert the shank of the saw blade into the blade holder (12)

as far as it will go.

X Release the blade clamp (10).

Saw blade storage (fig. C)

Saw blades (11) can be stored in the storage compartment

located on the side of the tool.

X Open the cover (3) of the saw blade storage compartment

by holding the tab on the top of the cover (3) and pulling it

outward.

X The blades are retained in the compartment by a magnetic

strip. To remove a blade, press down on one end of the

blade to raise the other end, and remove.

X Close the cover (3) of the saw blade storage compartment

and make sure that it is latched closed.

Warning! Close the compartment door securely before

operating the saw.

Connecting a vacuum cleaner to the tool (fig. D)

An adaptor is required to connect a vacuum cleaner or dust

extractor to the tool. The dust extraction adaptor (6) can be

purchased from your local Black & Decker retailer.

X Push the adaptor (6) into the dust extraction outlet (5).

X Connect the vacuum cleaner hose to the adaptor (6).

Use

Adjusting the shoe plate for bevel cuts (fig. E and F)

Warning! Never use the tool when the shoe plate is loose or

removed.

The shoe plate (7) can be set to a left or right bevel angle of

up to 45°.

X Pull the shoe plate locking lever (4) outwards to unlock the

shoe plate (7) from the 0 deg position (fig. E).

X Pull the shoe plate (7) forward and set the required bevel

15°, 30° and 45° indicated in the bevel angle window.

X Push the shoe plate locking lever (4) back towards the saw

to lock the shoe plate (7).

To reset the shoe plate (7) for straight cuts:

X Pull the shoe plate locking lever (4) outwards to unlock the

shoe plate (7).

X Set the shoe plate (7) to an angle of 0° and push the shoe

plate backwards.

X Push the shoe plate locking lever (4) back towards the saw

to lock the shoe plate (7).

8

ENGLISH

How to use the Auto Select

TM

dial (fig. G)

This tool is fitted with a unique Auto Select

TM

Dial (8) to set the speed and the pendulum blade action for various cutting

applications. To select the optimum speed and pendulum blade action for the type of material being cut, turn the dial (8) as

shown in the table below:

Switching on and off

X To switch the tool on, press the on/off switch (2).

X To switch the tool off, release the on/off switch (2).

X For continuous operation, press the lock-on button (1) and

release the on/off switch (2).

X To switch the tool off when in continuous operation, press

the on/off switch (2) and release it.

Sawing

Hold the tool firmly with both hands while cutting.

The shoe plate (7) should be held firmly against the material

being cut. This will help prevent the saw from jumping,

reduce vibration and minimise blade breakage.

X Let the blade run freely for a few seconds before starting

the cut.

X Apply only a gentle pressure to the tool while performing

the cut.

Operating the laser (fig. H - K) (‘L’ units only)

Installing the batteries (fig. H)

Detach the laser module (14) from the jigsaw by removing

the screw (13) and pulling the laser module forward. Insert

two new 1.5 Volt AAA alkaline batteries, making sure to

match the (+) and (-) terminals correctly. Re-attach the laser

module (14).

Adjusting the laser side-to-side (fig. I)

Note: The laser is intended as a cutting aid and does not

guarantee a precise cut.

Warning! Do not adjust the laser with the jigsaw plugged in.

X Use the laser adjustment screw (15) to align the laser line

with the saw blade if needed.

The laser visibility (power) will be reduced if the jigsaw is

overheated. The laser may not be visible when the saw is

overloaded for a prolonged period of time. The laser visibility

Icon Application Speed/Pendulum Blade Type

Kitchen work surfaces,

work tops, laminate

board

Fast speed, No

pendulum

General wood

Scrolling/curves/

craftwork, hardwoods,

decking, flooring

Fast speed, No

pendulum

Scrolling wood

General wood

Plywood and wood

panels

Fast speed, medium

pendulum

General wood

General timber, soft

wood, fast rip cutting

Fast speed, max

pendulum

General wood

Plastics, Perspex, PVC

Medium speed,

medium pendulum

General purpose

Sheet metal tin plate,

ceramic tile, fibreglass

sheet

Low speed, No

pendulum

Metal or ceramic or

fibreglass blade

Slow speed, precision

start

Slow speed, No

pendulum

Choose the correct

blade for the

application

9

ENGLISH

will gradually return to normal when the tool cools down even

when the tool is unplugged.

Warning! Do not leave the overheated laser switched ON.

Make sure that the switch is in the OFF position and remove

the batteries to remove power from the laser.

Using the laser (fig. J and K)

The laser projects the line of cut (18) on to the surface of the

workpiece.

X To switch the laser on, press the button (16).

X To switch the laser off, press the button (16) again.

Viewing from directly above the jigsaw, the line of cut (17)

can be easily followed. Should this view be restricted for any

reason, the laser can be used as an alternative cutting guide.

X Use a pencil to mark the cutting line (17).

X Position the jigsaw over the line (17).

X Switch on the laser.

Operating the work light (fig. L and M) ('W' units only)

Units that include a 'W' in the catalogue number are provided

with an LED light (19) to illuminate the area around the

blade.

X To switch the work light on, slide the switch (20) to the on

position (I).

X To switch the work light off, slide the switch (20) to the

off position (0).

Hints for optimum use

Sawing laminates

When cutting laminates, splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate

is sitting on the presentation surface either use a saw blade

that cuts on the downward stroke or:

X Use a fine-tooth saw blade.

X Saw from the back surface of the workpiece.

X To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Sawing metal

Be aware that sawing metal takes much more time than

sawing wood.

X Use a saw blade suitable for sawing metal.

X When cutting thin sheet metal, clamp a piece of scrap wood

to the back surface of the workpiece and cut through this

sandwich.

X Spread a film of oil along the intended line of cut.

Maintenance

Your Black & Decker tool has been designed to operate over

a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

X Regularly clean the ventilation slots in your tool using a soft

brush or dry cloth.

X Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid get inside the tool and never immerse any part of

the tool into liquid.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your tool needs

replacement, or if it is of no further use to you,

think of the protection of the environment. Black

& Decker repair agents will accept old Black &

Decker tools and ensure that they are disposed

of in an environmentally safe way.

Separate collection of used products and

packaging allows materials to be recycled and

used again. Re-use of recycled materials helps

prevent environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection of

electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and

recycling of Black & Decker products once they have

reached the end of their working life. To take advantage of

this service please return your product to any authorised

repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair

agent by contacting your local Black & Decker office at the

address indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full details of

our after-sales service and contacts are available on the

Internet at: www.2helpU.com.

At the end of their useful life, discard batteries with

due care for our environment. Remove the

batteries as described above.

X Place the batteries in suitable packaging to ensure that the

terminals cannot be short-circuited.

X Take the batteries to a local recycling station.

10

ENGLISH

Technical data

EC declaration of conformity

KS900 Series, KS950 Series

Black & Decker declares that these products conform to:

98/37/EC, 89/336/EEC, EN 60745, EN 55014, EN61000,

IEC 60825+A1+A2:2001

L

pA

(sound pressure) 87 dB(A),

L

WA

(acoustic power) 98 dB(A),

hand/arm weighted vibration <6.87 m/s

2

K

pa

(sound pressure uncertainty 3 dB(A),

K

wa

(sound power uncertainty 3 dB(A),

Kevin Hewitt

Director of Consumer Engineering

Spennymoor, County Durham

DL16 6JG,

United Kingdom

24-06-2007

Guarantee

Black & Decker is confident of the quality of its products and

offers an outstanding guarantee. This guarantee statement

is in addition to and in no way prejudices your statutory

rights. The guarantee is valid within the territories of the

Member States of the European Union and the European

Free Trade Area.

If a Black & Decker product becomes defective due to faulty

materials, workmanship or lack of conformity, within

24 months from the date of purchase, Black & Decker

guarantees to replace defective parts, repair products

subjected to fair wear and tear or replace such products to

make sure of the minimum inconvenience to the customer

unless:

X The product has been used for trade, professional or hire

purposes.

X The product has been subjected to misuse or neglect.

X The product has sustained damage through foreign

objects, substances or accidents.

X Repairs have been attempted by persons other than

authorised repair agents or Black & Decker service staff.

To claim on the guarantee, you will need to submit proof of

purchase to the seller or an authorised repair agent. You can

check the location of your nearest authorised repair agent by

contacting your local Black & Decker office at the address

indicated in this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our after-

sales service and contacts are available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.co.uk to

register your new Black & Decker product and to be kept up

to date on new products and special offers. Further

information on the Black & Decker brand and our range of

products is available at www.blackanddecker.co.uk.

KS900 Series KS950 Series

Voltage Vac 230 230

Rated input W 620 650

No-load speed min

-1

800-3200 800-3200

Max. depth of cut

Wood mm 85 85

Steel mm 5 5

Aluminium mm 15 15

Weight kg 2.8 2.8

(with laser) kg 3.1 3.1

Page is loading ...

Black & Decker KS950SW Owner's manual

Black & Decker KS950SW Owner's manual

in other languages

Related papers

Other documents