Gladiator GAAC68PSDG Operating instructions

Type
Operating instructions

This manual is also suitable for

Gladiator GAAC68PSDG features a 15-amp, fused, grounded electrical supply with nine electrical outlets and a visual over-current protection switch. This heavy-duty power strip is designed to be permanently installed on 6' or 8' Gladiator® workbenches. It's ideal for use in the garage, providing a safe and convenient power source for your power tools, chargers, and other equipment. Plus, the included tool caddies offer additional storage for your tools and accessories.

Gladiator GAAC68PSDG features a 15-amp, fused, grounded electrical supply with nine electrical outlets and a visual over-current protection switch. This heavy-duty power strip is designed to be permanently installed on 6' or 8' Gladiator® workbenches. It's ideal for use in the garage, providing a safe and convenient power source for your power tools, chargers, and other equipment. Plus, the included tool caddies offer additional storage for your tools and accessories.

WORKBENCH POWER STRIP SAFETY
2253730A
IT'S TIME TO RETHINK THE GARAGE.™
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
LE GARAGE REPENSÉ.™
WORKBENCH POWER STRIP
Installation Instructions
CONTACTO MÚLTIPLE PARA
MESA DE TRABAJO
Instrucciones de Instalación
BARRE MULTIPRISE POUR ÉTABLI
Instructions d’installation
TABLE OF CONTENTS/ÍNDICE/TABLE DES MATIÈRES
WORKBENCH POWER STRIP SAFETY...... 1
INSTALLATION REQUIREMENTS ............... 2
Tools and Parts ........................................... 2
Electrical Requirements .............................. 2
Power Strip Use Requirements .................. 2
INSTALL POWER STRIP............................... 3
6 ft (1.8 m) Workbench................................ 3
8 ft (2.4 m) Workbench................................ 3
INSTALL TOOL CADDIES............................. 4
TROUBLESHOOTING ................................... 5
WARRANTY ................................................... 5
SEGURIDAD DEL CONTACTO
MÚLTIPLE PARA MESA DE TRABAJO....... 6
REQUISITOS DE INSTALACIÓN.................. 6
Herramientas y piezas ................................ 6
Requisitos eléctricos................................... 7
Requisitos de uso del contacto múltiple.... 7
INSTALACIÓN DEL
CONTACTO MÚLTIPLE................................ 7
Mesa de trabajo de 6 pies (1,8 m).............. 7
Mesa de trabajo de 8 pies (2,4 m).............. 8
INSTALACIÓN DE LOS ESTUCHES PARA
HERRAMIENTAS........................................... 8
SOLUCIÓN DE PROBLEMAS ...................... 9
GARANTÍA ................................................... 10
SÉCURITÉ DE LA BARRE
MULTIPRISE POUR ÉTABLI.......................11
EXIGENCES D'INSTALLATION ..................11
Outillage et pièces.....................................11
Spécifications électriques .........................11
Utilisation de la barre multiprise................12
INSTALLATION DE LA
BARRE MULTIPRISE...................................12
Établi de 6 pi (1,8 m)..................................12
Établi de 8 pi (2.4 m)..................................13
INSTALLATION DES PORTE-OUTILS .......13
DÉPANNAGE................................................14
GARANTIE ....................................................15
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read
and follow the instructions provided with any tools listed here.
Tools Needed:
Parts Supplied:
Electrical Requirements
IMPORTANT: Be sure you have the proper electrical connection
before you install the power strip on the workbench.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only, 15-amp, fused, grounded electrical
supply is required. Use an outlet that cannot be turned off by a
switch. Do not use an extension cord.
NOTE: Before moving or cleaning the work bench disconnect the
power strip from the electrical source. When you are finished,
reconnect the power strip to the electrical source.
Over-Current Circuit Protection
The power strip is designed with a visual over-current protection
switch that operates as follows:
Over-current protection switch is in the ON position and
the green light is lit
The circuit has not tripped and the power strip can be used.
Over-current switch has been tripped
The green light will go out, and the over-current protection switch will
move to the OFF position. Unplug all items from the power strip. To
restore power, push the over-current protection switch back to the
ON position. Plug items back in one at a time, while watching to see
if the green light goes out and the over-current protection switch
moves to the OFF position again. If it does, unplug items until you are
sure that the green light is remaining lit and the over-current
protection switch is remaining in the ON position.
Power Strip Use Requirements
Intended for use in a garage.
The 6 ft (1.8 m) power strip is designed to be permanently
installed on the Gladiator
®
workbench.
There are nine electrical outlets on the power strip. All outlets are
connected to the over-current protection switch.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
To reduce the risk of fire, electric shock, or injury when using your power strip, follow these basic precautions:
SAVE THESE INSTRUCTIONS
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Unplug before servicing.
Replace all parts and panels before operating.
⁷⁄₁₆" Socket wrench
³⁄₁₆" Wood drill bit
¹⁄₁₆" Wood drill bit
Drill
Phillips screwdriver
Flat-blade screwdriver
Tape measure
Tool caddies (2)
#8 x ¹⁄₄" Phillips-head
screws (4)
¹⁄₄" x ³⁄₄" Lag bolts (6)
#8 x ¹⁄₂" Phillips-head
screws (2)
#8 x ¹⁄₄" Phillips-
head screws (4)
#8 x ¹⁄₂" Phillips-
head screws (2)
¹⁄₄" x ³⁄₄" Lag
bolts (6)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
3
INSTALL POWER STRIP
The workbench power strip can be installed on either the 6 ft (1.8 m) or the 8 ft (2.4 m) workbench. Before installing the power strip, verify the
size of your workbench (6 ft or 8 ft) (1.8 m or 2.4 m) and follow the corresponding installation instructions.
6 ft (1.8 m) Workbench
1. Remove the power strip and tool caddies from the box. Locate
the hardware packed in one of the tool caddies, and verify
contents. See Parts Supplied.
2. Place and align the power strip on the back edge of the
workbench.
3. Hold the power strip in place. Using the six holes in the power
strip back panel as a template, mark the workbench.
Before Installation
4. Using a ³⁄₁₆" wood drill bit, drill ³⁄₄" to 1" deep starter holes where
marked.
NOTE: While drilling, hold the drill level.
5. Using the six ¹⁄₄" lag bolts (provided), attach the power strip to
the workbench.
NOTE: Hand tighten each lag bolt. When all six lag bolts are in
place, tighten them completely with a ⁷⁄₁₆" socket wrench. Do not
overtighten.
After Installation
8 ft (2.4 m) Workbench
1. Remove the power strip and tool caddies from the box. Locate
the hardware packed in one of the tool caddies, and verify
contents. See Parts Supplied.
2. Measure 12" (30.48 cm) from an edge of the workbench and
mark a line.
3. Use the line as a guide to center the power strip on the back
edge of the workbench.
Before Installation
4. Hold the power strip in place. Using the six holes in the power
strip back panel as a template, mark the workbench.
5. Using a ³⁄₁₆" wood drill bit, drill ³⁄₄" to 1" deep starter holes where
marked.
NOTE: While drilling, hold the drill level.
6. Using the six ¹⁄₄" lag bolts (provided), attach the power strip to
the workbench.
NOTE: Hand tighten each lag bolt. When all six lag bolts are in
place, tighten them completely with a ⁷⁄₁₆" socket wrench. Do not
overtighten.
After Installation
A. Front
B. Back
A
B
A. Front
A
A. Front
B. Back
12"
(30.48 cm)
12"
(30.48 cm)
A
B
A. Front
A
4
INSTALL TOOL CADDIES
The tool caddies can either be mounted on the 8 ft (2.4 m) workbench (one caddy on each side of the power strip), or mounted on Gladiator
®
GearWall
®
panels or GearTrack channels.
Option 1: Mount on 8 ft Workbench
The tool caddies are reversible. They can be mounted on the
workbench with the larger holes toward the front or back as desired.
1. Screw the four #8 x ¹⁄" Phillips-head screws (provided) into the
two holes on each end of the power strip. Do not completely
tighten.
2. Align the eyelet holes with the two screws on each side of the
power strip and slide the tool caddies into position.
3. At the bottom of each tool caddy, locate the eyelet hole closest
to the corner of the workbench. Using the hole as a template,
mark the workbench. Remove the tool caddies.
Before Installation
4. Using a ¹⁄₁₆" wood drill bit, drill starter holes into the workbench
where marked.
NOTE: While drilling, hold the drill vertical.
5. Reattach the tool caddies to the power strip by aligning the
eyelet holes with the two power strip screws on each side and
sliding the tool caddies into position.
6. Screw one #8 x ¹⁄" Phillips-head screw (provided), into each
starter hole in the workbench.
7. Completely tighten all the screws. Do not overtighten.
After Installation
Option 2: Mount on Gladiator
®
GearWall
®
Panels or
GearTrack Channels
1. Insert the bracket top into the wall track.
2. Push down on the bracket bottom to lock into place.
A. Tool caddies
B. Eyelet hole
12" (30.48 cm)
A
B
5
TROUBLESHOOTING
Power Strip will not Operate
Is the power cord unplugged? Plug into a grounded
3 prong outlet.
Has a household fuse blown, or has a circuit breaker
tripped? Replace the fuse or reset the circuit breaker. If the
problem continues, call an electrician.
Is the over-current protection on the power strip tripped? If
the power on/off switch is not lit, the over-current protection may
be tripped. See Over-Current Circuit Protection.
GLADIATOR
®
GARAGEWORKS POWER STRIP WARRANTY
ONE-YEAR LIMITED WARRANTY
For one year from the date of purchase, when this product is operated and maintained according to the instructions attached to or furnished
with the product, Gladiator
®
GarageWorks will replace or repair the defective product or parts to correct defects in materials or workmanship.
Gladiator
®
GarageWorks will not pay for:
1. Service calls to correct the installation of any Gladiator
®
GarageWorks products or to instruct you on how to use or install them.
2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, fire, flood, improper
installation, acts of God, neglect, corrosion, modification or mishandling.
3. Shipping or freight fees to deliver replacement products or to return defective products.
4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial environment or
handled in any way inconsistent with the installation instructions included with the product.
5. Cosmetic damage including scratches, dings, dents or cracks that do not affect the structural or functional capability of the product.
6. Replacement parts or product for Gladiator
®
GarageWorks products operated outside the United States and Canada.
7. In Canada, travel or transportation expenses for customers who reside in remote areas.
8. Any labor costs during the limited warranty period.
9. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE
LIMITED TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS
OR EXCLUSIONS ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Gladiator
®
GarageWorks dealer to determine
if another warranty applies.
If you need service, call the Gladiator
®
GarageWorks Customer eXperience Center, 1-866-342-4089 (toll-free), from anywhere in the U.S.A. In
Canada, contact your Whirlpool Canada LP designated service company or call 1-800-807-6777.
In the United States, Gladiator
®
GarageWorks means Whirlpool Corporation, Benton Harbor, Michigan 49022. In Canada, Gladiator
®
GarageWorks means Whirlpool Canada LP, Mississauga, ON L5N 3A7.
8/05
Keep this book and your sales slip together for future reference.
You must provide proof of purchase or installation date for in-
warranty service.
Write down the following information about your Power Strip to
better help you obtain assistance or service if you ever need it. You
will need to know your complete model number and serial number.
You can find this information on the model and serial label located on
the back of the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Gladiator GAAC68PSDG Operating instructions

Type
Operating instructions
This manual is also suitable for

Gladiator GAAC68PSDG features a 15-amp, fused, grounded electrical supply with nine electrical outlets and a visual over-current protection switch. This heavy-duty power strip is designed to be permanently installed on 6' or 8' Gladiator® workbenches. It's ideal for use in the garage, providing a safe and convenient power source for your power tools, chargers, and other equipment. Plus, the included tool caddies offer additional storage for your tools and accessories.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI