Ikelite Universal Fiber Optic Mount Kit User manual

Ikelite
Brand
Ikelite
Model
Universal Fiber Optic Mount Kit
Category
Underwater camera housings
Type
User manual

Ikelite Universal Fiber Optic Mount Kit provides an easy way to add fiber optic ports to almost any existing housing. Simply cut to size and adhere to the top of the housing above the camera's built-in flash. Provides two ports for the attachment of one or two fiber optic cords.

This mount is compatible with a variety of fiber optic cords, including:

  • Ikelite 4501 Fiber Optic Coiled Cord
  • Sea&Sea Fiber Optic Cable (L-type) Product No. 50107
  • INON Optical D Cable "Non-wireless type" L-Connector
  • Olympus UW Fiber Optic Cable PTCB-E02
  • Nauticam Optical Fiber Cable No. 26211 Nauticam to INON

Ikelite Universal Fiber Optic Mount Kit provides an easy way to add fiber optic ports to almost any existing housing. Simply cut to size and adhere to the top of the housing above the camera's built-in flash. Provides two ports for the attachment of one or two fiber optic cords.

This mount is compatible with a variety of fiber optic cords, including:

  • Ikelite 4501 Fiber Optic Coiled Cord
  • Sea&Sea Fiber Optic Cable (L-type) Product No. 50107
  • INON Optical D Cable "Non-wireless type" L-Connector
  • Olympus UW Fiber Optic Cable PTCB-E02
  • Nauticam Optical Fiber Cable No. 26211 Nauticam to INON
Thank you for your purchase of Ikelite equipment. Please read these instructions completely
before attempting to operate or dive with this product.
This Mount provides an easy way to add fiber optic ports to almost any existing housing. Simply
cut to size and adhere to the top of the housing above the camera's built-in flash. Provides two
ports for the attachment of one or two fiber optic cords. For
best results, use in conjunction with
your housing's flash deflector to avoid backscatter.
4402 Universal Fiber Optic Mount
Attaching Universal Fiber Optic Mount to a Housing
1. Insert one end of a compatible fiber optic cord into one of the two circular port openings in the
Mount on the velcro side. Insert the other end of the compatible fiber optic cord into the
functioning strobe that you intend to trigger.
2. Hold the Mount over the housing where you intend to attach it. Choose an area that will allow
good adhesion an
d allow the Fiber Optic Cord to easily see the camera flash.
3. With the camera inside the housing, fire the camera flash several times to make sure the
strobe is properly triggered. A properly charged strobe will fire along with each camera flash.
4. Remove the fiber optic cord from the Mount. Using scissors, trim any excess Velcro material
from the Mount which could interfere with housing controls
or functions. Note: Only trim what
is necessary to assure good adhesion to the housing - Diagram A.
Velcro with adhesive backing
Universal Fiber Optic Mount
Contents
Diagram A
Diagram B
Cut away excess Velcro that
may interfere with camera controls
or functions BEFORE attaching
to camera housing
Fiber Optic Cord
Adhesive
Backing
Velcro
Port Mount
Ikelite Underwater Systems
50 West 33rd Street
Indianapolis, IN 46208 USA
www.ikelite.com
Universal Mount Optical Port Kit_01-0813
© 2013 Ikelite Underwater Systems
Ikelite Underwater Systems
Service Department
50 West 33rd St.
Indianapolis, IN 46208 USA
Email: [email protected]
Phone: 317-923-4523
This Ikelite product is warranted against any manufacturing defects for a period of one (1)
year from the origi
nal date of purchase. Defective products should be returned to Ikelite
postage paid. Ikelite will, at its sole discretion, repair or replace such products, and will return
to customer postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this Ikelite product.
Customer Support
Limited Warranty
Evidence of purchase date must be provided to obtain warranty service.
No prior authorization is required. You may return directly to us or through your dealer.
Please include a brief description of the problem, any relevant email correspondence, and/or
instructions. Always include name, shipping address, email address, and phone number
inside of the package. Send postage paid to:
Ikeli
te Underwater Systems
Attention: Service Department
50 West 33 Street
Indianapolis, IN 46208 USA
No reimbursements for postage paid will be issued.
Note: Ikelite does not repair this item. A 4402 Mount sent in for service that is found to be
defective will be replaced.
Returning Products for Service
- Ikelite 4501 Fiber Optic Coiled Cord
- INON Optical D Cable "Non-wireless type" L-Connector
- Sea&Sea Fiber Optic Cable (L-type) Product No. 50107
- Olympus UW Fiber Optic Cable PTCB-E02
- Nauticam Optical Fiber Cable No. 26211 Nauticam to INON
- Nauticam Optical Fiber Cable No. 26212 Nauticam to Sea&Sea
Compatible Fiber Optic Cords
5. Remove the adhesive backing from the Velcro and attach the Mount to the housing area
determined in step 2 - Diagram B.
6. Re-attach fiber optic cord and test fire strobe.
Attaching Ports Mount to a Housing (continued)
  • Page 1 1
  • Page 2 2

Ikelite Universal Fiber Optic Mount Kit User manual

Ikelite
Brand
Ikelite
Model
Universal Fiber Optic Mount Kit
Category
Underwater camera housings
Type
User manual

Ikelite Universal Fiber Optic Mount Kit provides an easy way to add fiber optic ports to almost any existing housing. Simply cut to size and adhere to the top of the housing above the camera's built-in flash. Provides two ports for the attachment of one or two fiber optic cords.

This mount is compatible with a variety of fiber optic cords, including:

  • Ikelite 4501 Fiber Optic Coiled Cord
  • Sea&Sea Fiber Optic Cable (L-type) Product No. 50107
  • INON Optical D Cable "Non-wireless type" L-Connector
  • Olympus UW Fiber Optic Cable PTCB-E02
  • Nauticam Optical Fiber Cable No. 26211 Nauticam to INON
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents