ViewSonic XG2401 User guide

Brand: ViewSonic

Model: XG2401

Type: User guide

This manual is also suitable for

XG2401-S

ViewSonic XG2401-S is a high-performance gaming monitor designed to provide immersive and seamless gaming experiences. With its rapid 1ms response time and blazing-fast 240Hz refresh rate, this monitor ensures smooth and fluid gameplay without motion blur or ghosting, even in fast-paced action sequences. The XG2401-S also boasts a stunning Full HD 1080p resolution and an impressive 100% sRGB color coverage, delivering vibrant and lifelike visuals for both gaming and multimedia content.

XG2401/VG2401mh-PRO

Display

User Guide

Model No. VS16265

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Thank you for choosing ViewSonic

With over 25 years as a world leading provider of visual solutions,

ViewSonic is dedicated to exceeding the world’s expectations for

technological evolution, innovation, and simplicity. At ViewSonic, we

believe that our products have the potential to make a positive impact

in the world, and we are confident that the ViewSonic product you have

chosen will serve you well.

Once again, thank you for choosing ViewSonic !

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding

regulations. Confirmed corresponding applications shall refer to nameplate labels

and relevant markings on unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage

Directive 2006/95/EC.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and

Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates

the requirement NOT to dispose the equipment as unsorted municipal

waste, but use the return and collection systems according to local law.

TCO Information

Congratulations!

This product is TCO Certified – for Sustainable IT

TCO Certified is an international third party sustainability certification for IT

products. TCO Certified ensures that the manufacture, use and recycling of IT

products reflect environmental, social and economic responsibility. Every TCO

Certified product model is verified by an accredited independent test

laboratory.

This product has been verified to meet all the criteria in TCO Certified, including:

Corporate Social Responsibility

Socially responsible production - working conditions and labor law in manufacturing country

Energy Efficiency

Energy efficiency of product and power supply. Energy Star compliant, where applicable.

Environmental Management System

Manufacturer must be certified according to either ISO 14001 or EMAS.

Minimization of Hazardous Substances

Limits on cadmium, mercury, lead & hexavalent chromium including requirements for mercury-free

products, halogenated substances and hazardous flame retardants.

Design for Recycling

Coding of plastics for easy recycling. Limit on the number of different plastics used.

Product Lifetime, Product Take Back

Minimum one-year product warranty. Minimum three-year availability of spare parts. Product take-

back.

Packaging

Limits on hazardous substances in product packaging. Packaging prepared for recycling

Ergonomic, User-centered design

Visual ergonomics in products with a display. Adjustability for user comfort (displays, headsets)

Acoustic performance – protection against sound spikes (headsets) and fan noise (projectors, com-

puters) Ergonomically designed keyboard (notebooks)

Electrical Safety, minimal electro-magnetic Emissions

Third Party Testing

All certified product models have been tested in an independent, accredited laboratory.

A detailed criteria set is available for download at www.tcodevelopment.com, where you can also find

a searchable database of all TCO Certified IT products.

TCO Development, the organization behind TCO Certified, has been an international driver in the

field of Sustainable IT for 20 years. Criteria in TCO Certified are developed in collaboration with

scientists, experts, users and manufacturers. Organizations around the world rely on TCO Certified as

a tool to help them reach their sustainable IT goals. We are owned by TCO, a non-profit organization

representing office workers. TCO Development is headquartered in Stockholm, Sweden, with regional

presence in North America and Asia.

For more information, please visit

www.tcodevelopment.com

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive) and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr

) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.

(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India) This product complies

with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers in

concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for

the exemptions set in Schedule 2 of the Rule.

Cautions and Warnings

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings and follow all instructions.

4. Sit at least 18” / 45cm from the LCD display.

5. Always handle the LCD display with care when moving it.

6. Never remove the rear cover. This LCD display contains high-voltage parts. You

may be seriously injured if you touch them.

7. Do not use this equipment near water. Warning: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

8. Avoid exposing the LCD display to direct sunlight or another heat source. Orient

the LCD display away from direct sunlight to reduce glare.

9. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the

Display” in this guide for further instructions.

10. Avoid touching the screen. Skin oils are difficult to remove.

11. Do not rub or apply pressure to the LCD panel, as it may permanently damage

the screen.

12. Do not block any ventilation openings. Install the equipment in accordance with

the manufacturer’s instructions.

13. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including amplifiers) that produce heat.

14. Place the LCD display in a well ventilated area. Do not place anything on the

LCD display that prevents heat dissipation.

15. Do not place heavy objects on the LCD display, video cable, or power cord.

16. If smoke, an abnormal noise, or a strange odor is present, immediately switch

the LCD display off and call your dealer or ViewSonic. It is dangerous to continue

using the LCD display.

17. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade

and the third prong are provided for your safety. If the plug does not fit into your

outlet, consult an electrician for replacement of the outlet.

18. When connecting to a power outlet, DO NOT remove the ground prong. Please

ensure grounding prongs are NEVER REMOVED.

19. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet

is located near the equipment so that it is easily accessible.

20. Only use attachments/accessories specified by the manufacturer.

(Continued on next page)

21. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the equipment. When a cart is used,

use caution when moving the cart/equipment combination to avoid

injury from tipping over.

22. Unplug this equipment when it will be unused for long periods of time.

23. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

24. Usage of other than specified head- or earphones can result in hearing loss due

to excessive sound pressures.

Contents

Compliance Information

FCC Compliance Statement ................................................................................... i

Industry Canada Statement .................................................................................... i

CE Conformity for European Countries ..................................................................i

TCO Information ....................................................................................................ii

Declaration of RoHS2 Compliance ....................................................................... iii

Indian Restriction of Hazardous Substances........................................................ iii

Cautions and Warnings ........................................................................................iv

Product Registration ..............................................................................................2

For Your Records ..................................................................................................2

Getting Started

Package Contents .................................................................................................3

Quick Installation ...................................................................................................4

Additional Software Installation (Optional).............................................................5

Wall Mounting (Optional) .......................................................................................5

Using the LCD Display

Setting the Timing Mode........................................................................................6

OSD and Power Lock Settings ..............................................................................6

Adjusting the Screen Image ..................................................................................7

Main Menu Controls ..............................................................................................8

Main Menu Explanation .........................................................................................8

Power Management ..............................................................................................9

Other Information

Specifications ......................................................................................................10

Cleaning the LCD Display ...................................................................................11

Troubleshooting ...................................................................................................12

Customer Support ...............................................................................................13

Limited Warranty .................................................................................................14

Mexico Limited Warranty .....................................................................................16

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS, DisplayPort, and DDC are trademarks of VESA.

NERGY STAR

is a registered trademark of the U.S. Environmental Protection

Agency (EPA).

As an ENERGY STAR

partner, ViewSonic Corporation has determined that this

product meets the ENERGY STAR

guidelines for energy efficiency.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

the right to change product specifications without notice. Information in this

document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

The ViewSonic CD also provides an opportunity for you to print the product

registration form. Upon completion, please mail or fax to a respective ViewSonic

office. To find your registration form, use the directory “:\CD\Registration”.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

Your LCD displays serial number is located on the rear side of the display.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

XG2401/VG2401mh-PRO

ViewSonic Widescreen LCD Display

VS16265

XG2401/VG2401mh-PRO_UG_ENG Rev. 1A 09-23-15

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing.

Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Getting Started

Congratulations on your purchase of a ViewSonic

LCD display.

Important! Save the original box and all packing material for future shipping needs.

NOTE: The word “Windows” in this user guide refers to Microsoft Windows operating

system.

Package Contents

Your LCD display package includes:

• LCD display

• Power cord

• DP cable

• USB cable

• Quick Start Guide

• ViewSonic CD

- User Guide

- INF/ICM files*

- Registration information

- Additional software (Optional)

NOTE:

* The INF file ensures compatibility with Windows operating systems, and the

ICM file (Image Color Matching) ensures accurate on-screen colors. ViewSonic

recommends that you install both the INF and ICM files.

* The video cables included in your package may vary depending on your country.

Please contact your local reseller for more information.

Quick Installation

1. Connect video cable

• Make sure both the LCD display and computer are turned OFF.

• Remove rear panel covers if necessary.

• Connect the video cable from the LCD display to the computer.

Macintosh users: Models older than G3 require a Macintosh adapter. Attach the

adapter to the computer and plug the video cable into the adapter.

To order a ViewSonic

Macintosh adapter, contact ViewSonic Customer Support.

2. Connect power cord (and AC/DC adapter if required)

1315

46810

1214

161820

Power Cord

Audio Out

HDMI

DisplayPort

USB

3. Turn ON LCD display and computer

Turn ON the LCD display, then turn ON the computer. This sequence (LCD

display before computer) is important.

NOTE: Windows users may receive a message asking them to install the INF file.

To access the file, please use the directory ":\CD\vsfiles".

4. Insert the ViewSonic CD into the computer’s CD drive.

If your computer does not have a CD-ROM drive, please refer to Customer

Support page.

5. Windows users: Set the timing mode (example: 1024x768)

For instructions on changing the resolution and refresh rate, see the graphics

card’s user guide.

6. Installation is complete. Enjoy your new ViewSonic LCD display.

Additional Software Installation (Optional)

1. Load the ViewSonic CD on your CD/DVD drive.

2. Double click on the "Software" folder and choose an application, if desired.

3. Double click on the Setup.exe file and follow the onscreen instructions to

complete the simple installation.

Wall Mounting (Optional)

NOTE: For use only with UL Listed Wall Mount Bracket.

To obtain a wall-mounting kit or height adjustment base, contact ViewSonic

your local dealer. Refer to the instructions that come with the base mounting kit. To

convert your LCD display from a desk-mounted to a wall-mounted display, do the

following:

4. Verify that the power button is turned Off, then disconnect the power cord.

5. Lay the LCD display face down on a towel or blanket.

6. Remove the base. (Screws removal might be required.)

7. Find and identify one of the following VESA mount interfaces (a,b,c) located on

the back of your display (refer to “Specifications” page for your displays mounting

interface). Attach the mounting bracket from the VESA compatible wall mounting

kit using screws of the appropriate length.

a. b. c.

75mm

100mm

200mm

8. Attach the LCD display to the wall, following the instructions in the wall-mounting

kit.

Using the LCD Display

Setting the Timing Mode

Setting the timing mode is important for maximizing the quality of the screen image

and minimizing eye strain. The timing mode consists of the resolution (example

1024 x 768) and refresh rate (or vertical frequency; example 60 Hz). After setting

the timing mode, use the OSD (On-screen Display) controls to adjust the screen

image.

For optimal picture quality, please use the recommended timing mode specific to

your LCD display listed on the “Specification” page.

To set the Timing Mode:

• Setting the resolution: Access "Appearance and Personalization" from Control

Panel via the Start Menu, and set the resolution.

• Setting the refresh rate: See your graphic card’s user guide for instructions.

IMPORTANT: Please make sure that your graphics card is set to 60Hz vertical

refresh rate as the recommended setting for most LCD displays. Choosing a non-

supported timing mode setting may result in no image being displayed, and a

message showing “Out of Range” will appear on screen.

OSD and Power Lock Settings

• OSD Lock: Press and hold [1] and the up arrow ▲ for 10 seconds. If any buttons

are pressed the message OSD Locked will display for 3 seconds.

• OSD Unlock: Press and hold [1] and the up arrow ▲ again for 10 seconds.

• Power Button Lock: Press and hold [1] and the down arrow ▼ for 10 seconds.

If the power button is pressed the message Power Button Locked will display

for 3 seconds. With or without this setting, after a power failure, your LCD

display’s power will automatically turn ON when power is restored.

• Power Button Unlock: Press and hold [1] and the down arrow ▼ again for 10

seconds.

Adjusting the Screen Image

Use the buttons on the front control panel to display and adjust the OSD controls

which display on the screen.

Standby Power On/Off

Power light

Blue = ON

Orange = Power Saving

[1]

Displays the Main Menu or exits the control screen and saves

adjustments.

[2]

Displays the control screen for the highlighted control.

Also a shortcut to toggle analog and digital connection.

▲/▼

Scrolls through menu options and adjusts the displayed control.

Audio Adjust (▼) / Game Mode (

/▲)

Do the following to adjust the display setting:

1. To display the Main Menu, press button [1].

NOTE: All OSD menus and adjustment screens disappear automatically after

about 15 seconds. This is adjustable through the OSD timeout setting in the

setup menu.

2. To select a control to adjust, press ▲ or ▼ to scroll up or down in the Main

Menu.

3. After the desired control is selected, press button [2].

4. To save the adjustments and exit the menu, press button [1] until OSD

disappear.

The following tips may help you optimize your display:

• Adjust the computer’s graphics card to support a recommended timing mode

(refer to “Specifications” page for recommended setting specific to your LCD

display). To find instructions on “changing the refresh rate”, please refer to the

graphics card’s user guide.

• If necessary, make small adjustments using H. POSITION and V. POSITION

until the screen image is completely visible. (The black border around the edge

of the screen should barely touch the illuminated “active area” of the LCD

display.)

Main Menu Controls

Adjust the menu items by using the up ▲ and down ▼ buttons.

NOTE: Check the Main Menu items on your LCD OSD and refer to Main Menu

Explanation below.

Main Menu Explanation

NOTE: The Main Menu items listed in this section indicates whole Main Menu items

of all models. The actual Main Menu details corresponding to your product please

refer to your LCD OSD Main Menu items.

Audio Adjust

adjusts the volume, mutes the sound, or toggles between inputs if you

have more than one source.

Advanced Image Adjust

The [Advanced Image Adjust] menu appears. You can execute various

adjustments and settings of advanced image quality.

Brightness

adjusts background black level of the screen image.

Color Adjust

provides several color adjustment modes, including preset color

temperatures and a User Color mode which allows independent

adjustment of red (R), green (G), and blue (B). The factory setting for this

product is native.

Contrast

adjusts the difference between the image background (black level) and

the foreground (white level).

Information

displays the timing mode (video signal input) coming from the graphics

card in the computer, the LCD model number, the serial number, and

the ViewSonic

website URL. See your graphics card’s user guide

for instructions on changing the resolution and refresh rate (vertical

frequency).

NOTE: VESA 1024 x 768 @ 60Hz (example) means that the resolution is

1024 x 768 and the refresh rate is 60 Hertz.

Input Select

toggles between inputs if you have more than one computer connected

to the LCD display.

Manual Image Adjust

displays the Manual Image Adjust menu. You can manually set a variety

of image quality adjustments.

Memory Recall

returns the adjustments back to factory settings if the display is operating

in a factory Preset Timing Mode listed in the Specications of this

manual.

Exception: This control does not affect changes made with the

Language Select or Power Lock setting.

Setup Menu

adjusts On-screen Display (OSD) settings.

Power Management

This product will enter to Sleep/Off mode with black screen and reduce power

consumption within 5 minutes of no signal input.

Other Information

Specifications

LCD Type

Display Size

Color Filter

Glass Surface

TFT (Thin Film Transistor), Active Matrix 1920 x 1080 LCD,

0.277 mm x 0.277 mm pixel pitch

Metric: 61 cm

Imperial: 24” (24” viewable)

RGB vertical stripe

Anti-Glare

Input Signal Video Sync HDMI x 2 (HDMI.TMDS digital, 100ohms)

Display port x 1

USB 3.0 x 2

:15-180 kHz, f

:24-120 Hz

Compatibility PC

Macintosh

Up to 1920 x 1080 Non-interlaced

Power Macintosh up to 1920 x 1080

Resolution

Recommended

Supported

1920 x 1080 @ 120 Hz

1920 x 1080 @ 50, 60, 100 Hz

1680 x 1050 @ 60 Hz

1600 x 1200 @ 60 Hz

1440 x 900 @ 60, 75 Hz

1280 x 1024 @ 60, 75 Hz

1280 x 960 @ 60Hz

1024 x 768 @ 60, 70, 72, 75 Hz

800 x 600 @ 56, 60, 72, 75 Hz

640 x 480 @ 60, 67,72,75 Hz

720 x 400 @ 70 Hz

Power Adaptor

Input Voltage 100-240 VAC, 50/60 Hz (auto switch)

Display area Full Scan 531.36 mm (H) x 298.89 mm (V)

20.92” (H) x 11.77” (V)

Operating

conditions

Temperature

Humidity

Altitude

+32 °F to +104 °F (0 °C to +40 °C)

20% to 90% (non-condensing)

To 10,000 feet

Storage

conditions

Temperature

Humidity

Altitude

-4 °F to +140 °F (-20 °C to +60 °C)

10% to 80% (non-condensing)

To 40,000 feet

Dimensions Physical 566 mm (W) x 432 mm (H) x 231 mm (D)

22.28” (W) x 17” (H) x 9.09” (D)

Wall Mount Distance 100 x 100 mm

Weight Physical 14.46 lb (6.5 kg)

Power saving

modes

Off

32W (typical, without Audio and USB)

<0.5W

Macintosh computers older than G3 require a ViewSonic

Macintosh adapter. To order an adapter, contact

ViewSonic.

Do not set the graphics card in your computer to exceed these timing mode; doing so may result in permanent

damage to the LCD display.

Please use the power adaptor from ViewSonic

or authorized source only.

Cleaning the LCD Display

• MAKE SURE THE LCD DISPLAY IS TURNED OFF.

• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR

CASE.

To clean the screen:

1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other

particles.

2. If the screen still not clean, apply a small amount of non-ammonia, non-alcohol

based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.

To clean the case:

1. Use a soft, dry cloth.

2. If the case still not clean, apply a small amount of a non-ammonia, non-alcohol

based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe

the surface.

Disclaimer

• ViewSonic

does not recommend the use of any ammonia or alcohol-based

cleaners on the LCD display screen or case. Some chemical cleaners have been

reported to damage the screen and/or case of the LCD display.

• ViewSonic will not be liable for damage resulting from use of any ammonia or

alcoholbased cleaners.

Troubleshooting

No power

• Make sure power button (or switch) is ON.

• Make sure A/C power cord is securely connected to the LCD display.

• Plug another electrical device (like a radio) into the power outlet to verify that the

outlet is supplying proper voltage.

Power is ON but no screen image

• Make sure the video cable supplied with the LCD display is tightly secured to

the video output port on the back of the computer. If the other end of the video

cable is not attached permanently to the LCD display, tightly secure it to the LCD

display.

• Adjust brightness and contrast.

• If you are using an Macintosh older than G3, you need a Macintosh adap

Wrong or abnormal colors

• If any colors (red, green, or blue) are missing, check the video cable to make

sure it is securely connected. Loose or broken pins in the cable connector could

cause an improper connection.

• Connect the LCD display to another computer.

• If you have an older graphics card, contact ViewSonic

for a non-DDC adapter.

Control buttons do not work

• Press only one button at a time.

Page is loading ...

ViewSonic XG2401 User guide

Brand: ViewSonic

Model: XG2401

Type: User guide

This manual is also suitable for

XG2401-S

Download PDF

report

ViewSonic XG2401 User guide

This manual is also suitable for

ViewSonic XG2401 User guide

Related papers

Other documents