Kohler K-702100-G55-SHP Installation guide

Kohler
Brand
Kohler
Model
K-702100-G55-SHP
Type
Installation guide

Kohler K-702100-G55-SHP is a bypass shower and bath door designed for easy installation and smooth operation. Here are some of its capabilities:

  • Adjustable height: The door panels can be raised or lowered to accommodate different shower or bath heights.
  • Reversible design: The door can be installed on either the left or right side of the shower or bath.
  • Frameless design: The door has a frameless design that gives it a sleek and modern look.
  • Durable construction: The door is made of high-quality materials that are resistant to rust and corrosion.
  • Easy to clean: The door is easy to clean with a mild soap and water solution.

Kohler K-702100-G55-SHP is a bypass shower and bath door designed for easy installation and smooth operation. Here are some of its capabilities:

  • Adjustable height: The door panels can be raised or lowered to accommodate different shower or bath heights.
  • Reversible design: The door can be installed on either the left or right side of the shower or bath.
  • Frameless design: The door has a frameless design that gives it a sleek and modern look.
  • Durable construction: The door is made of high-quality materials that are resistant to rust and corrosion.
  • Easy to clean: The door is easy to clean with a mild soap and water solution.
Bypass Shower and Bath Doors
K-702100, K-702102, K-702104
Installation Guide
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Reposition both wall jambs. Secure the wall jambs
with screws. Attach a bumper at the top and
bottom locations.
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not cut the top track the same
length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
Parts Identification
7
89
5
2
3
4
Required Tools
1
6
Model Number:______________
1177733-2-A
Apply 100% silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade
Miter Box
Number 2 Pencil
3/16"
5/16" Masonry Bit for Tile
5/16"
1036386**
Hardware Skin Pack
1/4" (6 mm)
Cut Line
"A" Mark
Notch
1
2
3
Screw Cover
Screw Cover
#8-18 x 1-1/2"
A
A
Groove
Tin Snips
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the
bottom-track leg to the outside. Tape the bottom
track in place and mark the position.
Measure distance "A." Subtract 1/4" (6 mm) or
the width of a number 2 pencil from "A" and cut
the bottom track.
Important! The bottom track and wall jamb must
sit flat against the shower ledge and the wall. If
needed, trim and file the wall jamb. Use a coin to
match and to transfer the corner radius of the
shower to the wall jamb.
1
#8-18 x 3/8"
#8-32 x 3/8"
Wall Jamb
Notch
#8-18 x 1-1/2"
Wall Jamb
Notch
Model Number Label
x2
x2
x2
Top Track
B
B
"B" Mark
Cut Line
1/32" (1 mm)
Measure distance “B” above the wall jambs.
Subtract 1/32" (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Bottom-Track
Leg
Bypass Bath Doors Bypass Shower Doors
(K-702104)1038763-03**
(K-702102)1038763-02**
(K-702100)
1038763-01**
Top Track
1013942
(5/64")
Key
1077762
Anchor
Screw Cover
1031943**
Screw Cover
1031943**
Screw Cover
1031943**
Bushing
1059792
Blind Nut
1050048-B
Roller
1044585
Screw
1051142-A
Outside Panel
1036970-**-* (K-702100)
1036972-**-* (K-702104)
1036973-**-* (K-702102)
Screw
1048208-C (Silver)
1048208-F (Brass)
Towel Bar
(Includes Hardware)
1036203-01**
[20" (508 mm)]
1036203-02**
[24" (610 mm)]
Wall Jamb
1172141-04** [56-13/16" (1443 mm)]
1172141-07** [68-13/16" (1748 mm)]
Bottom Track
10070.01 (Silver)
10070.02 (Brass)
10070.92 (Bronze)
10076.76 (Nickel)
Inside-Panel Guide
1017813-01** [27-7/16" (697 mm)]
1017813-02** [21-7/16" (545 mm)]
1048208-K (Brass)
Screw
1048208-B (Silver)
Inside Panel
1036975-**-* (K-702100)
1036977-**-* (K-702104)
1036978-**-* (K-702102)
1031943**
Screw Cover
Bumper
1131838**
8-32 x 1/4"
Sex Bolt
1077763-A
*When ordering the outside or inside
panel, glass pattern must be specified.
Rhapsody™
GC53
Portrait™
GC55
USA/Canada: 1-800-4KOHLER
Mexico: 001-800-456-4537
www.kohler.com
Hanger Bracket
10082.09 (Bronze)
1077761-01** (Silver, Brass, Nickel)
23
Outside the shower, use 100% silicone sealant to
seal along the entire length of the wall jambs and
the bottom track.
Inside the shower, use 100% silicone sealant to
seal along the entire length of the wall jambs and
in the corners where the wall jambs meet the
bottom track.
Position the top track over the wall jambs. Either
side of the top track can face out.
For both doors, insert a bushing into each hole at
the top of the glass panels. Install the hanger
brackets over the glass panels. Align the hanger
brackets with the mounting holes.
Insert a blind nut through each hanger bracket
and bushing. Secure with a sex bolt. Do not use
power tools! Do not overtighten!
10 11
12
1177733-2-A
Bushing
Blind Nut
Hanger
Bracket
Sex Bolt
Hanger
Bracket
8-32 x 1/4"
x2x2
22
20
© 2011 Kohler Co.
2
Reversible
x2
Towel Bar
Setscrew
14
Uncoated Side
#8-32 x 3/8"
Roller
Label
Screw
Door-Frame Holes
On the inside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the door-frame holes.
Outside-Panel
Leg
Uncoated
Side
Screw
Label
Roller
x2
#8-32 x 3/8"
13
On the outside panel, assemble a roller to the
middle hole of each hanger bracket. Place the
rollers on the same side as the outside-panel leg.
Lay flat.
#8-18 x 3/8"
Screw Cover
15
Lay the inside panel flat and partially thread the
screws into the panel. Install screw covers over
the side screws.
16
From the outside of the shower, install the
outside panel. The uncoated side faces the outside
of the shower. The outside-panel leg fits over the
bottom-track leg.
From the inside of the shower, install the inside
panel. The uncoated side faces the outside of the
shower.
17
19
If either panel needs adjustment, remove the door
and position the rollers in a new hole to raise or
lower the glass.
18
Install the inside-panel guide onto the partially
threaded screws. The inside-panel guide fits into
the bottom-track slot.
#8-18 x 3/8"
Screw Cover
Raise the glass.
Lower the glass.
Recommended Action
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 18.
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 18.
A. Determine whether door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
Recommended Action
A. When showering, make sure the inside panel is against the showerhead wall.
A. Adjust the door panel to line up with the wall jamb.
A. Check for proper silicone sealant application. See steps 22 and 23. Apply more silicone sealant in the leak location.
A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure
proper watertight seal. See step 23.
Recommended Action
A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.
B. Ensure the panel is properly engaged over the bottom track. See step 17.
C. Ensure the rollers are properly installed. See steps 13 and 14.
D. Clean any debris in the top track groove.
A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.
B. Ensure the inside-panel guide is properly secured to the bottom frame screws. See step 19.
C. Ensure the rollers are properly installed. See steps 13 and 14.
D. Clean any debris in the top track groove.
Symptom: Alignment
1. The top of the door panel is tilted away from the
wall.
2. The bottom of the door panel is tilted away from
the wall.
3. The door panel does not touch the bumper.
Symptom: Water Leaks
1. Water leaks between panels.
2. Water leaks between the wall jamb and
the door panel.
3. Water leaks under the bottom track.
4. Water leaks around the wall jamb area.
Symptom: Operation (open/close)
1. The outside panel is difficult to move.
2. The inside panel is difficult to move.
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from
date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses
any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for
removal or installation costs. Use of in-tank toilet cleaners will void the warranty.
To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or
E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by
calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within
Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com
in Mexico.
IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER
CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the
exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not
apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from
state/province to state/province.
This is Kohler Co.'s exclusive written warranty.
ONE-YEAR LIMITED WARRANTY
21
Install both towel bars. Insert the spacers. Use a
hex wrench to tighten the screws. Do not
overtighten!
Assemble both towel bars. The flat side of the
towel bar faces down. Tighten the setscrews
against the flat side of the towel bars.
1/4"-20 Screw
Spacers
x2
Flat Side
TROUBLESHOOTING
  • Page 1 1
  • Page 2 2

Kohler K-702100-G55-SHP Installation guide

Kohler
Brand
Kohler
Model
K-702100-G55-SHP
Type
Installation guide

Kohler K-702100-G55-SHP is a bypass shower and bath door designed for easy installation and smooth operation. Here are some of its capabilities:

  • Adjustable height: The door panels can be raised or lowered to accommodate different shower or bath heights.
  • Reversible design: The door can be installed on either the left or right side of the shower or bath.
  • Frameless design: The door has a frameless design that gives it a sleek and modern look.
  • Durable construction: The door is made of high-quality materials that are resistant to rust and corrosion.
  • Easy to clean: The door is easy to clean with a mild soap and water solution.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents