TotalLEDS 5981 Installation guide

Brand
TotalLEDS
Model
5981
Type
Installation guide

This manual is also suitable for

TotalLEDS 5981 is a magnetic retrofit kit that allows you to easily convert your existing fluorescent fixtures to energy-efficient LED technology. With its simple installation process and a variety of features, this kit is perfect for both residential and commercial applications. The kit includes a magnetic driver, LED boards, a color temperature switch, and all necessary hardware for a quick and hassle-free installation.

TotalLEDS 5981 is a magnetic retrofit kit that allows you to easily convert your existing fluorescent fixtures to energy-efficient LED technology. With its simple installation process and a variety of features, this kit is perfect for both residential and commercial applications. The kit includes a magnetic driver, LED boards, a color temperature switch, and all necessary hardware for a quick and hassle-free installation.

STEP 1: Turn off power and remove
the lamps and ballast cover.
Disconnect the incoming power from
the ballast, trim the tombstone wires,
and remove the ballast if desired or
required by law.
STEP 3: Place the RetroStrip magnetic
driver into the fixture, and ground driver.
Where required, driver and boards should
be permanently affixed to the fixture with
self-tapping screws provided.
STEP 4: Connect the new driver to
the incoming power.
STEP 7: Magnets are built-in for easy
installation. Magnets holders also slide
out. To permanently adhere to the
fixture, use self-tapping screws
provided.
STEP 8: Place the magnetized LED boards
into the fixture evenly and align with
existing lamp sockets/tombstones. Use
self-tapping screws where required. LED
bars “Plug and Play” connection whips
should face the same direction that the
driver harness is coming out of the ballast
cover for connection.
STEP 5: Apply the retrofit sticker. STEP 6: Select your color temperature
on the magnetized switch on harness.
See color kelvin temperature
suggestion chart in kit. Place
magnetized switch into the fixture.
STEP 2: Select your wattage on the
driver DIP switch. See detailed
instruction on back of sheet on how to
select and change your wattage. Default
wattage is set as per kit part number.
*Please read safety instructions before starting. Always have a qualified electrician install kits.
(856) 444-0662 • [email protected] • www.totalleds.com
OPTIONS: 35K, 40K, 50K
STEP 9: Connect wire harness to the
“Plug and Play” boards. Replace the
ballast cover and connect the wire
harness so it is accessible through
the end of ballast cover.
*Two bar fixture
*Two bar fixture
MAGNETIC RETROFIT KIT INSTALLATION
STEP 10: Turn on your power to
test your newly retrofitted fixture.
STEP 11: Installation is complete. Enjoy!
HOW TO USE THE DIP SWITCH ON DRIVER
EXAMPLE  20 WATT DRIVER SWITCH SELECTION CHART
NO.1  NO.3 CHANNEL SWITCH OUTPUT CURRENT
PIN
8W
10W
IRATED
0190mA
0240mA
URATED
38V
38V
1
-
ON
2
-
-
3
-
-
14W
16W
0320mA
0370mA
38V
38V
-
-
ON
-
-
ON
18W
20W
0410mA
0470mA
38V
38V
ON
-
-
ON
ON
ON
22W 0510mA 38V ON ON ON
UP (-)
DOWN (ON)
DOWN (ON)
MAGNETIC RETROFIT KIT INSTALLATIONMAGNETIC RETROFIT KIT INSTALLATION
(856) 444-0662 • [email protected] • www.totalleds.com
  • Page 1 1
  • Page 2 2

TotalLEDS 5981 Installation guide

Brand
TotalLEDS
Model
5981
Type
Installation guide
This manual is also suitable for

TotalLEDS 5981 is a magnetic retrofit kit that allows you to easily convert your existing fluorescent fixtures to energy-efficient LED technology. With its simple installation process and a variety of features, this kit is perfect for both residential and commercial applications. The kit includes a magnetic driver, LED boards, a color temperature switch, and all necessary hardware for a quick and hassle-free installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents