Super Lighting LED V1-L Operating instructions

V1-L
Brand
Super Lighting LED
Model
V1-L
Type
Operating instructions
User Manual Ver 1.0.4
Dimming data
Dimming range
RF 2.4GHz + Push Dim
30m
4096 levels
0-100%
Technical Parameters (Common Data)
Output power 180W/360W
(12V/24V)
Output voltage 12-24VDC
Output current 1CH,15A
Input and Output
Input voltage 12-24VDC
Input current 15.5A
Safety and EMC
EMC standard (EMC) EN301 489,EN 62479
Radio Equipment(RED) EN300 328
Certification CE,EMC,LVD,RED
EN60950
Safety standard(LVD)
Output type Constant voltage
Warranty and Protection
2years
Protection Reverse Polarity
Warranty
Input signal
Control distance
Dimming level
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
Tc:
+85
O
C
LVD
Single Color LED Controller
Features
●4096 levels 0-100% dimming smoothly without any flash.
●Match with Skydance’s 2.4G single zone or multiple zone dimming remote control.
●One RF controller accept up to 10 remote control.
●Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
●Synchronize on multiple number of controllers.
●Connect with external push switch to achieve on/off and 0-100% dimming function.
Additional features for professional version V1-L/P: ●
Logarithmic or linear dimming curve selectable.
●PWM frequency 250Hz, 500Hz, 2kHz or 8kHz selectable.
V1-L, V1-L/P Single Color LED Controller
Page 1
Mechanical Structures and Installations
27mm
175mm
160mm
45mm
Match key
Push switch common
Power input -
Power input +
LED output +
Push switch
Dip switch setting
(Only V1-L/P)
LED indicator
MATCH
IN PUT
12-24VDC
+
-
+
-
+
-
1 2
3
12 1 2 1 2
3
logarithmlinear
250Hz500Hz2KHz8KHz
PWM Frequency
Dimming Curve
123
LED output -
RED
Installation rack
●Connect with push switch
●Match with dimming remote
AC100-240V Power Supply
12-24VDC
Constant Voltage
MATCH
INPUT
12-24VDC
+
-
+
-
+
-
Single color LED strip
+
AC100-240V Power Supply
12-24VDC
Constant Voltage
MATCH
INPUT
12-24VDC
+
-
+
-
+
-
Single color LED strip
+
Push Switch
V1-L
V1-L
RF remote
Wiring Diagram
Standard version
V1-L
Professional version
V1-L/P
Standard Version: V1-L
Professional Version: V1-L/P
The standard version is single channel constant voltage RF controller with push-dim, and output current up to 15A.
The professional version has standard function, in addition to has 3 bit DIP switch to set output PWM frequency and
dimming curve.
User Manual V e r 1.0.4
V1-L, V1-L/P Single Color LED Controller
Page 2
Match Remote Control (two match ways)
Use the controller’s Match key
Match:
Short press match key, immediately press on/off
key (single zone remote) or zone key (multiple zone
remote) of the remote.
Use Power Restart
Match:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 3 times on the remote.
The light blinks 3 times means match is successful.
. Delete:
Switch off the power, then switch on power again,
immediately short press on/off key (single zone remote)
or zone key (multiple zone remote) 5 times on the remote.
The light blinks 5 times means all matched remotes were
deleted.
Delete:
Press and hold match key for 5s to delete all match,
The light blinks 5 times means all matched remotes
were deleted.
End usercanchoose thesuitable match/delete ways. Tw o optionsareoffered for selection:
Linear dimming curve Logarithmic dimming curve
100
90
80
70
60
50
40
30
20
10
PWMduty(%)
100
90
80
70
60
50
40
30
20
10
PWMduty(%)
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.6
50 60 70 80 90 100
Brightness(%)
10 20 30 40
Gamma=1.0
3 3
100
90
80
70
60
50
40
30
20
10
PWMduty(%)
W e can select four PWM frequency: 250Hz, 500Hz, 2kHz or 8kHz.
Higher PWM frequency, will cause lower output current, higher power noise,
but more suitable for camera(No flickers for video).
12121212
250Hz500Hz2KHz8KHz
Push Dim Function
●Short press:
T u r n onorofflight.
●Longpress (1-6s):
Press and holdtostep-less dimming,
Withevery other long press, the light level goestotheopposite direction.
●Dimming memory:
Light returns totheprevious dimming level whenswitched offand onagain, evenatpower failure.
●Synchronization:
Ifmorethan onecontroller areconnected tothesamepushswitch, doalong press for morethan10s,
then thesystem issynchronized and all lights inthegroup dimupto100%.
Thismeans thereisnoneedforany additional synchrony wire inlarger installations.
We recommend thenumberofcontrollers connected toapushswitch does not exceed 25pieces,
Themaximum length ofthewires frompushtocontroller should benomore than20meters.
The provided Push-Dim interface allows forasimpledimming method usingcommercially available non-latching
(momentary) wallswitchs.
Application notes
1. All the receivers in the same zone.
2. Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.
Zone 1 Zone 2 Zone 3
RF remote
30m 30m
Zone 4
RF remote
Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m,
as long as there is a receiver within 30m, the remote control distance can be limitless.
Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled
by the same remote.
Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range.
Strong signal sources such as WiFi routers and microwave ovens will affect the range.
W e recommend for indoor applications that receiver placements should be no further apart than15m.
30m
30m30m
Dimming curvesetting
Profession version V1-L/P DIP switch setting
PWM frequency setting
  • Page 1 1
  • Page 2 2

Super Lighting LED V1-L Operating instructions

V1-L
Brand
Super Lighting LED
Model
V1-L
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents