Hotpoint DSD60S.0 Dual Fuel Cooker User manual

Brand: Hotpoint

Model: DSD60S.0 Dual Fuel Cooker

Category: Microwaves

Type: User manual

This manual is also suitable for

Instructions for

Installation and Use

60cm DUAL FUEL COOKER

Contents

Introduction, 2

Safety Information, 3

Installation, 4-7

Features, 8

The Controls, 9

Clock/ Minute Minder Operation, 10

Hotplate, 11

Top Oven Cookery Notes, 12

Main Oven Cookery Notes, 13

Grilling, 14

Oven Cooking Charts, 15-16

Care and Cleaning, 17-19

Something Wrong With Your Cooker?, 20

If Something Still Goes Wrong, 21

Disposal of Your Appliance, 21

Hotpoint Service Cover, 22-23

Guarantee Information, 24

English, 2

GBGB

HUD 61

DSD 60 S

Introduction

Technical Characteristics

Top Oven

Usable Volume: 35 Litres

ENERGY LABEL - Top Oven

Directive 2002/40/EC on the label of electric ovens

Norm EN 50304

Declared energy consumption for

Natural convection Class

heating mode: Conventional

Main Oven

Usable Volume: 65 Litres

ENERGY LABEL - Main Oven

Directive 2002/40/EC on the label of electric ovens

Norm EN 50304

Declared energy consumption for

Natural convection Class

heating mode: Fan Oven

Voltage and Frequency

230-240V~ 50/60Hz

To the Installer:

Before installation, fill in the product details on the

back cover of this book.

The information can be found on the rating plate.

To the User:

You must read the instructions prior to installing and

using the appliance and then retain them for future

reference.

! Before operating your new appliance please read

this instruction booklet carefully. It contains

important information concerning the safe operation,

installation and maintenance of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

Retention of this Instruction Book

This Instruction Book must be kept handy for

reference as it contains important details on the safe

and proper use of the appliance.

If you sell or pass the appliance to someone else, or

move house and leave it behind, make sure this

Book is also provided so the new owner can become

familiar with the appliance and safety warnings.

Your new appliance is guaranteed* and will give

lasting service. This guarantee is only applicable if

the appliance has been installed in accordance with

the installation instructions detailed in this booklet.

To help make best use of your cooking equipment,

please read this booklet carefully.

The cooker is designed specifically for domestic use

and responsibility will not be accepted for use in any

other installation.

When the cooker is first used an odour may be

emitted, this will cease after a period of use.

When first using the cooker ensure that the room is

well ventilated (e.g. open a window or use an

extractor fan) and that persons who may be

sensitive to the odour avoid any fumes.

It is suggested that any pets be removed from the

room until the smell has ceased. This odour is due

to temporary finish on oven liners and elements and

also any moisture absorbed by the insulation.

Your new cooker is guaranteed and will give lasting

service.

The guarantee is only applicable if the cooker has

been installed in accordance with the Installation

Instructions.

The cooker is designed specifically for domestic use

and responsibility will not be accepted for use in any

other installation.

Your new cooker is guaranteed and will give lasting

service.

The guarantee is only applicable if the cooker has

been installed in accordance with the Installation

Instructions.

The cooker is designed specifically for domestic use

and responsibility will not be accepted for use in any

other installation.

* The guarantee is subject to the provisions that

the appliance:

(a) Has been used solely in accordance with

the Users Instruction Book.

(b) Has been properly connected to a suitable

supply voltage as stated on the rating plate

attached to this equipment.

accident or been modified or repaired by

any person other than the authorised employee or

agent.

(d) Has been correctly installed.

Our policy is one of continual improvement in design

and development, therefore strict accuracy of

illustrations and descriptions cannot be guaranteed.

Please read the precautions below before using your

cooker.

ALWAYS . . .

ALWAYS make sure you understand the controls before

using the cooker.

ALWAYS check that all controls on the cooker are turned

off after use.

ALWAYS stand back when opening an oven door to allow

heat to disperse.

ALWAYS use dry, good quality oven gloves when

removing items from the ovens.

ALWAYS take care when removing items from the top

oven/grill when the main oven is on, as the

contents may be hot.

ALWAYS keep the oven and grill doors closed when the

cooker is not in use.

ALWAYS place pans centrally over the hotplate burners

and position them so that the handles cannot

accidentally be caught or knocked or become

heated by other burners.

ALWAYSALWAYS

ALWAYS

keep the cooker clean, as a build up ofkeep the cooker clean, as a build up of

keep the cooker clean, as a build up of

grease or fat from cooking can cause agrease or fat from cooking can cause a

grease or fat from cooking can cause a

fire.fire.

fire.

ALWAYS allow the cooker to cool before cleaning.

ALWAYS follow the basic principles of food handling and

hygiene to prevent the possibility of bacterial

growth.

ALWAYS keep ventilation slots clear of obstructions.

ALWAYS turn off the electricity supply before cleaning or

replacing an oven lamp.

ALWAYS refer servicing to Gas Safe registered appliance

service engineers.

ALWAYS The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions outlined in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous. The

manufacturer may not be held liable for any

damage resulting from improper, incorrect and

unreasonable use of the appliance.

SAFETY ADVICE IN CASE OF A CHIP-PAN FIRE

In the event of a chip pan fire or any other pan fire.

1.TURN OFF THE COOKER APPLIANCE AT THE WALL

SWITCH.

2.COVER THE PAN WITH A FIRE BLANKET OR DAMP

CLOTH, this will smother the flames and extinguish the

fire.

3.LEAVE THE PAN TO COOL FOR AT LEAST 60

MINUTES BEFORE MOVING IT. Injuries are often caused

by picking up a hot pan and rushing outside with it.

NEVER USE A FIRE EXTINGUISHER TO PUT OUT A PAN

FIRE as the force

of the extinguisher is likely to tip the pan over.

Never use water to extinguish oil or fat fires.

NEVER . . .

NEVER leave children unsupervised where the cooker

is installed as all surfaces will get hot during

and after use.

NEVER allow anyone to sit or stand on any part of the

cooker.

NEVER store items that children may attempt to reach

above the cooker.

NEVER heat up unopened food containers as pressure

can build up causing the container to burst.

NEVER store chemicals, food stuffs, pressurised

containers in or on the cooker, or in cabinets

immediately above or next to the cooker.

NEVER fill a deep fat frying pan more than 1/3 full of oil,

and never use a lid. DO NOT LEAVE

UNATTENDED WHILE COOKING.

NEVER place flammable or plastic items on or near the

hotplate.

NEVER use proprietary spillage collectors on the

hotplate.

NEVER use the cooker as a room heater.

NEVER dry clothes or place other times over or near to

the hotplate or oven/gril doors.

NEVER wear garments with long flowing sleeves whilst

cooking.

NEVER let children play with the appliance.

NEVER should the appliance be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the

very least, be supervised by someone who

assumes responsibility for their safety or

receive preliminary instructions relating to the

operation of the appliance.

NOTE:NOTE:

NOTE: The use of a gas cooking appliance results in the

production of heat and moisture in the room in which it is

installed. Always ensure that the kitchen is well ventilated;

keep natural ventilation holes open or install a mechanical

ventilation device (mechanical extractor hood).

In particular when using the grill or more than one hotplate

burner, open a window if a mechanical ventilation device

is not operating.

!for their safety or receive preliminary instructions relating

to the operation of the appliance.

Safety Information

Installation

WARNING - THIS APPLIANCE MUST

BE EARTHED.

Mains Connection

Your cooker should have been checked to ensure

that the voltage corresponds with your supply

voltage, this is stated on the rating plate, which is

situated on the outer rear panel.

The model number and serial number are located on

the front of the cooker, as shown on the Feature's

page.

The cooker must be connected by a competent

person such as one who is a, NICEIC registered

contractor to a suitable double-pole control unit with

a minimum rating of 32A and a minimum contact

clearance of 3mm (applicable to newer properties,

older properties where a 30A double pole control unit

and a minimum contact clearance of 3mm is

acceptable).

The double pole control unit should be fitted

adjacent to the cooker, in accordance with IEE

regulations. The control unit must be within 2 metres

of but not directly above the appliance and should

be easily accessible in the event of an emergency.

The power supply cable should conform to B.S.6004

with a conductor size of 6mm2, minimum.

Access to the mains terminals is gained by

removing the rear access cover. The mains cable

must pass through the cable clamp adjacent to the

terminal block. Sufficient cable should be used to

allow the cooker to be pulled out for servicing.

Ensure that the mains cable is routed away

from any brackets affixed to the rear panel and

is not trapped to the rear wall when pushing the

cooker into position between cabinets.

Levelling

Four feet are fitted which can be adjusted up or

down to set the height (900mm - 930mm) and level

the cooker.

The feet can be simply screwed in or out to lower or

raise the cooker.

After the correct height is achieved, lock the feet

into position by tightening the locking nut using an

open ended spanner.

CAUTION:CAUTION:

CAUTION: Some soft floor coverings may get

damaged if the cooker is not moved carefully.

NOTE:NOTE:

NOTE: Ensure oven shelves are level by using a

spirit level on the rod shelves.

Siting the Cooker

The cooker is designed to fit between kitchen

cabinets spaced 600mm apart. The space either

side need only be sufficient to allow withdrawal of

the cooker for servicing and cleaning.

It can be used with cabinets one side or both as well

as in an angled corner setting. It can also be used

freestanding.

Adjacent side walls which project above hob level,

must not be nearer to the cooker than 150mm and

should be protected by heat resistant material. Any

overhanging surface or cooker hood should not be

nearer than 650mm.

Note: This appliance must NOT be fitted on a

platform.

Moving the Cooker

Before moving your cooker, switch off at the cooker

control unit, ensure that it is cool.

Open the grill door sufficiently to allow a comfortable

grip on the underside front edge of the oven roof,

avoiding any grill elements.

Radio Interference

This appliance conforms to EN 55014 regarding

suppression of radio and television interference.

Note: Take care in moving the cooker as it is

heavy. Take care to ensure that any floor

covering is not damaged.

The cooker is fitted with a safety

chain that must be attached to a

hook, secured to the wall behind the

appliance.

This appliance conforms with the followingThis appliance conforms with the following

This appliance conforms with the following

European Economic Community directives:European Economic Community directives:

European Economic Community directives:

- 2006/95/

EC EC

EC of 12/12/06 (Low Voltage) and

subsequent modifications;

- 2004/108/

ECEC

EC of 15/12/04 (Electromagnetic

Compatibility) and subsequent modifications;

- 2009/142/

ECEC

EC of 30/11/09 (Gas) and subsequent

modifications (only for models which use gas);

- 93/68/

EECEEC

EEC of 22/07/93 and subsequent

modifications.

- 2002/96/

ECEC

- 1275/2008 (Stand-by/ Off Mode)

Prior to installation, ensure that the local distribution

conditions (nature of the gas and gas pressure) and

the adjustment conditions are compatible. The

adjustment conditions for this appliance are stated

on the data badge which is fitted on the back panel.

This appliance is not designed to be connected to a

combustion products evacuation device. It must be

installed and connected in accordance with current

installation regulations. particular attention should be

given to the relevant requirements regarding

ventilation.

MODEL NUMBERS HUD61

Category II2H3+ (GB)

These models are set to burn NATURAL GAS (G20)

at 20 mbar but can be converted for use on BUTANE

(G30) at 28-30mbar or PROPANE (G31) at 37mbar

with the use of the LPG conversion kit that can be

obtained free of charge, if you contact our Genuine

Parts and Accessories department (see back page).

GAS SAFETY (INSTALLATION & USE)

REGULATIONS

It is the law that all gas appliances are installed by

competent persons in accordance with the current

edition of the above regulations. It is in your interest

and that of safety to ensure compliance with the law.

In the UK,Gas Safe registered installers work to safe

standards of practice. The cooker must also be

installed in accordance with BS 6172. Failure to

install the cooker correctly could invalidate the

warranty liability claims and could lead to

prosecution.

LOCATION

The cooker may be located in a kitchen, kitchen/

diner or a bed-sitting room, but not in a room

containing a bath or shower. The cooker must not be

installed in a bed-sitting room of less than 20m

When adjusted for use on Butane (G30) or Propane

(G31), the cooker must not be installed in a room or

internal space below ground level, e.g. in a

basement.

PROVISION FOR VENTILATION

The room containing the cooker should have an air

supply in accordance with BS 5440: Part 2.

The room must have an opening window or

equivalent; some rooms may also require a

permanent vent. If the room has a volume between 5

and 10m

, it will require an air vent of 50cm

effective area unless it has a door which opens

directly to outside. If the room has a volume of less

than 5m

, it will require an air vent of 100cm

effective area. If there are other fuel burning

appliances in the same room, BS 5440: Part 2

should be consulted to determine air vent

requirements.

TECHNICAL DATA

Gas connection Rp ½ (½" BSP female)

Pressure test point Front left hotplate injector

Gas rate adjustment None

Aeration adjustment None

Electrical connection 6mm

twin and earth

230/240V a.c. 50Hz.

Installation









HEAT INPUT INJECTOR HEAT INPUT INJECTOR

HOTPLATE

Front Left and Rear Right

3.05 kW 116 3.0 kW (220g/h) 86

HOTPLATE

Front Right and Rear Left

2.0 kW 103 2.0 kW (145g/h) 70

GRILL 2.2 / 2.4 kW

MAIN OVEN 1.8 / 2.0 kW

TOP OVEN 1.7 / 1.9 kW

Installation

SPACE FOR FIXING

The cooker can be close fitted below hotplate level.

This requires a minimum distance of 600mm between

cupboard units of hotplate height.

When installing next to a tall cupboard, partition or

wall, for a minimum distance of 400mm above hotplate

level, allow a side clearance of at least 65mm.

The diagram below illustrates the minimum

clearance between the cooker and adjacent walls,

cupboards etc.

The wall behind the cooker, 50mm below and 450mm

above, and the width of the cooker, must be a non-

combustible material such as ceramic wall tiles.

If the cooker is to be fitted close to a corner on the

left hand side, ensure that there is a clearance of at

least 50mm to allow the main oven door to open fully

for when removing oven shelves.

65 mm Min

840 mm Min

400 mm Min

600 mm Min

750mm Min

COOKER HOODS

If a cooker hood is to be installed, refer to the

cooker hood manufacturers' instructions regarding

fixing height.

UNPACKING THE COOKER

Unpack the components from inside the grill and

oven.

Check that the following parts are present:

Grill pan and grid Aluminium burner bodies(4)

Baking dish Pan supports

Main oven shelves (2) Enamelled burner caps (5)

Top oven/grill shelf (1) Literature

LEVELLING

Four skid feet are fitted which can be adjusted up or

down to level the cooker.

CONVERSION FOR USE ON BUTANE

(G30) OR PROPANE (G31)

Each burner requires the injector to be replaced and

bypass screws adjusted or replaced as follows:

1. Remove the loose hotplate burner parts.

2. Using a 7mm socket, replace the hotplate injectors

as appropriate (see table on previous page).

3. Re-position the loose burner parts.

4. Carefully pull off the hotplate control knobs.

5. Using a narrow flat bladed screwdriver rotate the

bypass screws fully clockwise. The hotplate tap

bypass screws are located down the centre of the

spindle.

6. Re-assemble the control panel parts.

7. Secure the self-adhesive LPG conversion label over

the gas details on the data badge.

STABILITY CHAIN

A hole in the gas inlet valve bracket can be used to

engage a stability chain.

CONNECTING TO GAS SUPPLY

300

670

Connection to the cooker should be made with an

approved appliance flexible connection to BS 669. A

length of 0.9 to 1.25m is recommended. The length

of hose chosen should be such that when the cooker

is in situ, the hose does not touch the floor.

Those cookers converted to use on LPG should be

connected with a hose suitable for LPG and capable

of withstanding a pressure of 50 mbar.

An adaptor backplate should be fitted within the

shaded area shown, to allow the cooker to be

pushed fully to the wall and to ensure that the

flexible hose is only likely to come into contact with

areas at the rear of the cooker that do not exceed a

temperature rise of 70°C.

Electrical Connection

Warning - THIS APPLIANCE MUST BE EARTHED

The cooker must be connected by a qualified

electrician to a suitable double - pole control unit

with a minimum rating of 32A and a minimum

contact clearance of 3mm, which should be fitted

adjacent to (but not above) the cooker, in

accordance with IEE regulations.

The power supply cable should conform to BS6004

with a conductor size of 6mm

The control unit should be easily accessible in the

event of an emergency.

This appliance conforms to EN55014 regarding

suppression of radio and television interference.

Access to the cooker terminals is by un-clipping the

cover. The mains cable must pass through the cable

clamp and the screws must be fully tightened.

Sufficient cable should be used to allow the cooker

to be pulled out for servicing. Ensure that the cover

is fully closed and secure afterwards.

Take care not to trap the mains cable when pushing

the cooker into its final position.

Operational Checks

After installation, check for gas soundness. The

supply pressure can be checked at one of the

hotplate burner injectors.

Check that the hotplate burners ignite correctly

and burn with a steady flame.

Check for a steady flame at the low setting.

Instruct the user on the operation of the cooker.

WARNING – THIS APPLIANCE MUST BEWARNING – THIS APPLIANCE MUST BE

WARNING – THIS APPLIANCE MUST BE

EARTHED.EARTHED.

EARTHED.

Electrical connection

Electric cookers come without a power supply cable.

The cooker is designed to operate on an electricity

supply which conforms to the electrical data shown

on the Rating Plate. The cooker can be connected to

the mains only after removing the back panel of the

cooker itself with a screwdriver.

N.B.:N.B.:

N.B.: the following installation procedure must be

carried out by a qualified electrician. The electrical

installation must comply with the IEE Regulations,

Building & local By-Lays.

For the installation of the feeding cable carry out the

following operations:

1 Open the terminal

board by inserting a

screwdriver into the

side tabs of the cover.

Use the screwdriver as

a lever by pushing it

down to open the cover

(see diagram).

2 Loosen the cable

clamp screw and

remove it, using a

screwdriver as a lever

(see figure).

3 Remove the wire

contact screws L-N-

then fasten the wires

under the screw heads,

respecting the colour

code: Black/Blue (N),

Red/Brown (L) and Bare Wire/Yellow-Green (

)

l Once the connections have been made, tighten

all the terminal screws fully.

l Fasten the supply cable in place with the clamp

and close the cover of the terminal board.

Features

NOTE: To keep the controls cool when the appliance is used, a flow of air may be blown from beneath the

control panel. If the appliance is still warm, this cooling fan will run on when all controls have been turned off.

This is normal and is not a fault.

The fan will stop once the appliance has cooled.

NOTE: Children should not be allowed to play with the appliance or tamper with the controls.

Timer

Grill pan handle

fixed/detachable

Top oven

rod shelf

Inner door glass

Oven light

Oven fan

Door Switch

'Stay Clean' liners

Main oven

rod shelf

Model number &

Serial number label

Inner door glass

Main Oven door

Top Oven door

'Stay Clean' liners

Control panel

Grill pan and

food support

Conventional Grill

Glass cover

The controls

Switch on the electricity supply to the cooker at the Cooker Control Unit.

ELECTRONIC

TIMER/

MAIN

OVEN

TOP OVEN

LEFT

FRONT

PLATE

LEFT

REAR

PLATE

RIGHT

REAR

PLATE

RIGHT

FRONT

PLATE

GRILL

PILOT LIGHT

TOP OVEN

PILOT LIGHT

MAIN OVEN

PILOT LIGH

ELECTRONIC IGINTION

BUTTON*

Control Knobs for the gas burners

The position of the gas burner controlled by each

one of the knobs is shown by a solid ring

•

. To

light one of the burners press down and turn the

corresponding knob counter clockwise to the

maximum maximum

maximum

setting. Each burner can be operated

at its maximum, minimum or intermediate power.

Shown on the knob are the different symbols for off

•

(the knob is on this setting when the symbol

corresponds with the reference mark on the control

panel), for

maximum maximum

maximum

and

minimum minimum

minimum

. To

obtain these settings, turn the knob counter

clockwise with respect to the off position. To turn off

the burner, turn the knob clockwise until it stops

(corresponding again with the

•

symbol).

! Should the burner flames accidentally go out,

turn off the control knob and wait at least 1

minute before trying to relight.

Main Oven Light

The main oven light can be switched on, when the

oven is not in use, by pressing the oven light button

on the display. The oven light will also operate

whenever the main oven door is opened.

NOTE: The oven light can be switched off when

the door is opened by pressing the oven light

button on the display, or by closing the door.

Cooling Fan

The cooling fan operates with the ovens and grill.

The fan will operate at full speed for a few seconds

and then reduce to a lower speed. The cooling fan

will only increase to full speed if the temperature

inside the cooker reaches above a certain limit.

Grill Control

The grill control will not operate unless the top oven

control is in the 'O' off position.

The grill control provides fully variable heat control

for either the twin grill or single (left hand side) grill

by selecting any number between 1 & 4.

When turned clockwise the twin grill will be switched

on and any power setting from 1 - 4 can be

selected. The power level numbers are indicated on

the control knob.

When turned anti-clockwise the single grill will be

switched on and any power setting from 1 - 4 can be

selected. The power level numbers are indicated on

the control knob.

The off position is identified by an 'O'.

*Available only in certain models.

/PROGRAMMER*

Clock/Minute

Minder Operation

DISPLAY

SET TIME

button

END OF

COOKING icon

CLOCK icon

DURATION

icon

TIMER icon

DECREASE TIME

button

INCREASE TIME

button

•• ••

! The Top Oven and Main Oven can be controlled by

the automatic timer. When the timer control has been

set for one oven, it is possible to use the other oven

only during the same automatic cooking programme.

! NEVER operate the grill when the ovens are

set to cook automatically because the oven

cavity can become warm and this may cause

bacterial growth in food.

Setting the clock

! The clock may be set when the oven is switched off

or when it is switched on, provided that the end time of

a cooking cycle has not been programmed previously.

After the appliance has been connected to the mains,

or after a blackout, the icon and the four numerical

digits on the DISPLAY will begin to flash.

1. Press the

button several times until the icon

and the four digits on the display begin to flash.

2. Use the “+” and “-” buttons to adjust the time; if you

press and hold either button, the display will scroll

through the values more quickly, making it quicker and

easier to set the desired value.

3. Wait for 10 seconds or press the

button again to

finalise the setting.

Setting the minute minder

! This function does not interrupt cooking and does not

affect the oven; it is simply used to activate the buzzer

when the set amount of time has elapsed.

1. Press the

button several times until the icon

and the three digits on the display begin to flash.

2. Use the “+” and “-” buttons to set the desired time;

if you press and hold either button, the display will

scroll through the values more quickly, making it

quicker and easier to set the value.

3. Wait for 10 seconds or press the

button again to

finalise the setting.

The display will then show the time as it counts down.

When this period of time has elapsed the buzzer will

be activated.

Programming cooking*

! A cooking mode must be selected before

programming can take place.

Programming the cooking duration

1. Press the

button several times until the icon

and the three digits on the DISPLAY begin to flash.

2. Use the “+” and “-” buttons to set the desired

duration; if you press and hold either button, the

display will scroll through the values more quickly,

making it quicker and easier to set the value.

3. Wait for 10 seconds or press the

button again to

finalise the setting.

4. When the set time has elapsed, the text END

appears on the DISPLAY, the oven will stop cooking

and a buzzer sounds. Press any button to stop the

buzzer and turn all control knobs to the 0 position.

• For example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed. The programme

will stop automatically at 10:15 a.m.

Setting the end time for a cooking mode

! A cooking duration must be set before the cooking

end time can be scheduled.

1. Follow steps 1 to 3 to set the duration as detailed

above.

2. Next, press the

button until the icon and the

four digits on the DISPLAY begin to flash.

3. use the “+” and “-” buttons to adjust the cooking

end time; if you press and hold either button, the

display will scroll through the values more quickly,

making it quicker and easier to set the desired value.

4. Wait for 10 seconds or press the

button again to

finalise the setting.

5. When the set time has elapsed, the text END

appears on the DISPLAY, the oven will stop cooking

and a buzzer sounds.

Press any button to stop it.

Programming has been set when the and buttons

are illuminated. The DISPLAY shows the cooking end

time and the cooking duration alternately.

• For example: It is 9:00 a.m. and a duration of 1

hour has been programmed. 12:30 is scheduled

as the end time. The programme will start

automatically at 11:30 a.m.

Cancelling a programme

To cancel a programme:

• press the

button until the icon corresponding

to the setting you wish to cancel and the digits on

the display are flashing. Press the “-” button until

the digits 00:00 appear on the display.

• Press and hold the “+” and “-” buttons; this will

cancel all the settings selected previously,

including timer settings.

*Available only in certain models.

The hotplate lid is fitted with a safety device which

cuts off the gas supply to the hotplate burners

unless the lid is fully open. Do not use the safety

device as a means of controlling the hotplate

burners.

The hotplate has two high speed burners and two

simmering burners which will accommodate pans

between 100mm (4") and 240mm (91/2") diameter.

All pans should be positioned centrally over the

burners.

TO USE THE HOTPLATE

1. Remove any items or spillage from the top of the

lid and then raise it to its fully open position.

2. Push in and turn the control knob of the chosen

burner anti-clockwise to the large flame symbol.

Continue to press the ignition button* until the sparks

light the gas.

3. Turn the control knob anti-clockwise to reduce the

heat input. Only turn the control knob between the

large flame symbol and the small flame symbol

when adjusting the setting.

4. To turn off, turn the control knob fully clockwise to

the symbol O.

DO NOT use the hotplate unless all pan supports

are in position.

DO NOT use mis-shapen pans which may be

unstable.

DO NOT use round base woks directly on the pan

supports.

DO NOT use the glass lid as a working surface.

Each burner is fitted with a spark ignitor for lighting

the gas. To ensure rapid lighting of the burners

every time they are used, the ignitors must be kept

clean and dry. Remove any food spillage or

cleaning materials from the ignitor using a small

nylon brush such as a tooth brush. Access to the

ignitor can be achieved by lifting off the loose burner

parts carefully when the burners are cool.

When the hotplate burner bodies and caps are

removed for cleaning, be careful not to drop any

food particles or cleaning materials into the burner

bases, to avoid the possibility of blocking the gas

jets.

If aluminium based pans are used, a silvery deposit

may appear on the top edge of the pan support

fingers. See 'Care and Cleaning' section for cleaning

information.

SAFETY REQUIREMENTS FOR DEEP FAT FRYING

1. Never fill chip pans more than one third full with oil

or fat.

2. Never leave oil or fat unattended during the heating

or cooling period.

3. Never heat fat or fry with a lid on the pan.

4. Always dry food thoroughly before frying, and lower

it slowly into the hot oil or fat. Frozen foods in

particular will cause frothing and spitting if added

too quickly.

5. Always keep the outside of the pan clean and free

from streaks of oil or fat.

HOW TO DEAL WITH A FAT FIRE

1. Do not move the pan.

2. Turn off the hotplate burners.

3. Smother the flames with a fire blanket or damp cloth

to extinguish the fire. Do not use water or a fire

extinguisher as the force of it may spread the

burning fat or oil over the edge of the pan.

4. Leave the pan for at least 60 minutes before moving

it.

Models with Hob Gas Burner Safety Devices to

Prevent Leaks

These models

can be identified

by the presence

of the device

itself.

! Since the hob

burners are

equipped with a

safety device,

you must hold the control knob in for about 3-7

seconds after the burner has been lighted to allow

the gas to pass until the safety thermocouple has

heated.

HOB GAS BURNER

SAFETY DEVICE

ELECTRONIC

LIGHTING DEVICE

Hotplate

*Available only in certain models.

The top oven should be used to cook small

quantities of food.The oven is designed so that the

grill element operates at a reduced heat output, this

is combined with a heating element situated

underneath the floor of the oven.

To ensure even cooking of the food it is important

that cooking utensils are positioned correctly on the

oven shelf so that the element is directly above.

There are two cooking positions, the shelf placed on

runner 1 or 2 (from the base), do not use shelves

upside down.

Food/utensils must not be placed directly on the

oven floor.

There should always be at least 25mm (1in) between

the top of the food and the grill element.

Warning: Items stored in top oven will get hot when

main oven is in use.

Top Oven

Cookery Notes

Operation

To heat the oven, turn the control knob

clockwise.The top oven pilot light will come on and

remain on until the oven reaches the required

temperature.The pilot light will automatically go on

and off during cooking as the thermostat maintains

the correct temperature.

Cooking meat/poultry

Small joints of meat up to 1.5kg (3 lbs), or poultry,

up to 3.6kg (8 lbs) (60cm cookers) in weight can be

roasted in a small meat pan in the top oven. Larger

joints of meat/poultry weighing more than 3.6kg (8

lbs) (60cm cookers) should be roasted in the main

oven.

Do not use the grill pan as a meat pan in the

top oven as air circulation will be seriously

restricted.

Top oven as a warming compartment for plates

Place the plates/dishes on the shelf, positioned on

runner 1, turn top oven control to 100°C for 10-15

minutes.Never use grill control.

The oven is fitted with wirework shelf supports and

two rod shelves.

To heat the oven turn the knob clockwise, selecting

the require temperature between 80°C (176°F) and

230°C (450°F) as recommended in the temperature

chart. The pilot light will immediately come on and

remain on until the oven reaches the required

temperature. This light will then automatically go off

and on during cooking as the oven thermostat

maintains the correct temperature.

It should be noted that at the end of the cooking

period there may be a momentary puff of steam

when the oven door is opened. This will disperse in

a few seconds and is a perfectly normal

characteristic of an oven with a good door seal.

Since a circulaire fan oven heats up more

quickly,and generally cooks food at a lower

temperature than a conventional oven, pre-heating is

often unnecessary.However, foods such as bread,

scones,Yorkshire pudding,do benefit from being

placed in a pre-heated oven.

The 'oven temperature charts' are a guide only,

giving approximate cooking temperatures and

times.To suit personal taste and requirements, it

may be necessary to increase or decrease

temperatures by 10°C.

Unless otherwise indicated in the charts food should

be placed in a cold oven, i.e. without pre-heating. If

food is placed in an already hot oven, the

suggested cooking time should be reduced,

depending on the type and quantity of food being

cooked.

Main Oven

Cookery Notes

Oven positions

Since the distribution of heat in the circulaire fan

oven is very even, most foods will cook satisfactorily

on any shelf position, but the shelves should be

evenly spaced.

The top oven rod shelf can be used in the main oven

when cooking large quantities of food. Additional

shelves can be purchased through your oven

supplier or our Parts Department (see Key Contacts,

back page).

Food or utensils should Never be placed

directly an the floor of the oven for cooking.

Never use more than 3 shelves in the oven as air

circulation will be seriously restricted.To ensure oven

circulation do not use meat pans larger than 390 x

300mm (15"x12") and baking trays no larger than

330 x 255mm (13"x 10"), these should be positioned

centrally on the oven shelf.

Food should not be placed directly on the floor of

the oven. To avoid unnecessary cleaning, rod

shelves which are not in use, should be removed

from the oven.

Temperature and time

When all three shelves are used to cook large

quantities of food for home freezing or parties, it

may be necessary to increase the cooking times

given in the temperature charts by a few minutes, to

allow for the loss of heat due to extra time taken to

load the oven, and the larger mass of food. Baking

trays should have an equal gap at either side of the

oven.

Frozen meat and poultry

Joints of meat and whole birds should be defrosted

slowly, preferably in a domestic refrigerator (allowing

5-6 hours per 450g (1 lb), or at room temperature

(allowing 2-3 hours per 450g (1 lb).

Grilling

Grill Pan Handle

The grill pan handle is detachable from the pan to

facilitate cleaning and storage. Fix the pan handle

securely before use:

1. Fit the handle to the grill pan so that the external

‘hooks’ embrace the edge of the pan (fig. 1)

2. Make sure that the middle part of the handle fits

exactly the protruding support of the pan (fig .2)

and holds the pan from the bottom.

The food must be placed on the rack in the grill pan.

Position the grill pan on top of the oven rack. The

best results are achieved by placing the oven rack

on the uppermost shelves. Pouring a little water into

the grill pan will make the collection of grease

particles more efficient and prevent the formation of

smoke.

CAUTION - ACCESSIBLE PARTS MAY

BECOME HOT WHEN THE GRILL IS USED.

YOUNG CHILDREN SHOULD BE KEPT AWAY.

GRILLING SHOULD NEVER BE UNDERTAKEN

WITH THE GRILL DOOR CLOSED

The grill control is designed to provide variable

heat control of either the full width of the grill or

just the left half. Turning the control knob

clockwise will switch on the full width and turning

anti-clockwise will switch on just the left half.

A gentle flow of air will be blown from underneath

the control panel when the grill is in use.

TO USE THE GRILL

1. Open the grill/top oven door and place the shelf in

the required position.

2. Turn the grill control knob clockwise to 4 (or Max) for

full width grilling or anticlockwise for the half grill.

3. Slide the grill pan toward the back of the grill com-

partment until it stops.

4. Leave the control at 4 (or Max) for toast and for sealing

and fast cooking of foods. For thicker foods requiring

longer cooking, turn the control to a lower setting af-

ter sealing on both sides at 4 (or Max).

NOTE: The grill will not operate unless the top oven

control is in the OFF position.

Grilling can be started from cold but for best results

preheat for approximately 2 minutes.

The grill elements are covered by a wire mesh to

prevent access to live parts. Under no

circumstances should pointed objects be inserted

through the mesh.

During use, the mesh may become soiled. Do not

attempt to clean it while the grill is on. Turn the

cooker off at the control unit and wait until it has

cooled down before cleaning.

DO NOT cover the grill pan or grid with aluminium

foil as this can hold fat, intensify the heat

and cause a fire hazard.



   ! 

Scones Yes 210/220 10-15 Runner 2 from bottom of oven

Small Cakes Yes 180/190 20-25 Runner 2 from bottom of oven

Victoria Sandwich Yes 170/180 20-30 Runner 2 from bottom of oven

Sponge Sandwich Yes 180/190 20-25 Runner 2 from bottom of oven

Swiss Roll Yes 200/210 10-15 Runner 2 from bottom of oven

Semi-rich Fruit cakes Yes 150/160 60-75 7 inch Runner 2 from bottom of oven

Rich Fruit Cakes Yes 140/150 Depending on size Runner 1 or 2 from bottom of oven

Shortcrust Pastry Yes 190/200 Depending on size Runner 2 from bottom of oven

Puff Pastry Yes 200/210 Depending on size Runner 2 from bottom of oven

Yorkshire Pudding Yes 190/200 30-40 Runner 2 from bottom of oven

Individual Yorkshire Pudding Yes 200/210 20-30 Runner 2 from bottom of oven

Milk Pudding Yes 140/150 90-120 Runner 2 from bottom of oven

Baked Custard Yes 150/160 40-50 Runner 2 from bottom of oven

Bread Yes 200/210 30-45 Runner 1 from bottom of oven

Meringues Yes 100 150-180 Runner 2 from bottom of oven

"

   ! 

Scones Yes 210/220 8-10 Runner 2 from bottom of oven

Small Cakes 170/180 15-20 Runner 2 from bottom of oven

Victoria Sandwich 160/170 20-25 Runner 2 from bottom of oven

Sponge Sandwich Yes 170/190 15-20 Runner 2 from bottom of oven

Swiss Roll Yes 180/190 10-15 Runner 2 from bottom of oven

Semi-rich Fruit cakes 140/150 60-75 Runner 2 from bottom of oven

Rich Fruit Cakes 130/140 Depending on size Runner 1 or 2 from bottom of oven

Shortcrust Pastry 190/200 45-50 Runner 2 from bottom of oven

Puff Pastry 190/200 Depending on use Runner 2 from bottom of oven

Yorkshire Pudding Yes 180/190 40-45 Runner 2 from bottom of oven

Individual Yorkshire Pudding Yes 190/200 20-25 Runner 2 from bottom of oven

Milk Pudding 130/140 105-135 Runner 2 from bottom of oven

Baked Custard 140/150 40-50 Runner 2 from bottom of oven

Bread Yes 200/210 40-50 Runner 1 from bottom of oven

Meringues 80-90 180-240 Runner 2 from bottom of oven

Oven Cooking Charts

The most accurate method of testing the readiness of joints of meat or whole poultry is to insert a meat

thermometer into the thickest part of a joint, or the thickest part of poultry thighs, during the cooking period.The

meat thermometer will indicate when the required internal temp has been reached.

Beef - Rare: 60°C Lamb: 80°C Poultry: 90°C

Medium: 70°C Pork: 90°C

Well Done: 75°C Veal: 75°C



#   $%!& 

Beef/ Lamb

(slow roasting)

Yes 170/180 35 mins per 450g (1lb) + 35 mins over.

Runner 1 from

bottom of oven.

Beef/ Lamb

(foil covered)

Yes 190/200 35-40 mins per 450g (1lb)

Pork

(slow roasting)

Yes 170/180 40 mins per 450g (1lb) + 40 mins over

Pork

(foil covered)

Yes 190/200 40 mins per 450g (1lb)

Veal

(slow roasting)

Yes 170/180 40-45 mins per 450g (1lb) + 40 mins over

Veal

(foil covered)

Yes 190/200 40-45 mins per 450g (1lb)

Poultry/Game

(slow roasting)

Yes 170/180 25-30 mins per 450g (1lb) + 25 mins over

Poultry/Game

(foil covered)

Yes 190/200 25-30 mins per 450g (1lb)

Casserole

Cooking

Yes 150 2-2½ hrs

'()()*+

!Allow foil to touch sides of oven. !Cover oven interior with foil. !Cover shelves with foil.



   

Beef No 160/180

20-25 mins per 450g

(1lb) + 20 mins extra

Lamb No 160/180

20-30 mins per 450g

(1lb) + 25 mins extra

Pork No 160/180

25-30 mins per 450g

(1lb) + 25 mins extra

Veal No 160/170

25-30 mins per 450g

(1lb) + 25 mins extra

Chicken/ Turkey

up to 4kg (8lb)

No 160/180

18-20 mins per 450g

(1lb) + 20 mins extra

Turkey 4 to 5.5kg

(8 to12lb)

13-15 mins per 450g

(1lb) at 150/160oC

over 5.5kg (12lb)

allow 12 mins per

450g at 150oC

Casserole No 140-150 1½ - 2 Hrs

If using aluminium foil, never: 1. Allow foil to touch sides of oven. 2. Cover oven interior with foil. 3. Cover shelves with foil.

Oven Cooking Charts

Care and Cleaning

Door and Control Panel (Glass)

Regularly wipe with a clean, damp cloth and polish

with a clean, dry cloth.

Door and Control Panel Trims (Stainless Steel)

Regularly wipe with a clean, damp cloth and polish

with a clean, dry cloth.

WARNING: TO AVOID ELECTRIC SHOCK,

BEFORE REPLACING THE OVEN LIGHT,

SWITCH THE COOKER OFF AT THE COOKER

CONTROL UNIT (and allow to cool if the oven

has been used).

Replacement of the Oven Light

Unscrew the glass cover, using a suitable cloth to

protect the fingers and remove carefully. Unscrew

the existing light bulb, and remove. Screw the new

bulb into position and replace the glass cover, with

metal washer, until positioned securely.

WARNING: BEFORE CLEANING, SWITCH THE

COOKER OFF AT THE MAINS COOKER CONTROL

PANEL AND ALLOW IT TO COOL. IT IS

ESSENTIAL THAT THE OVENS ARE CLEANED

AND KEPT FREE FROM FATS, OIL AND GREASE.

'Stay Clean' Liners

'Stay Clean' liners are covered with a special enamel

which absorbs cooking soils. At higher temperatures

the soiling is slowly destroyed. In most cases normal

cooking at higher temperatures will permit this cleaning

to take place automatically. However, if higher cooking

temperatures are not used regularly then it may be

necessary, in order to prevent heavy soiling, to run the

oven at maximum temperature for at least two hours,

from time to time. The 'Stay Clean' liners can be

washed in warm soapy water followed by rinsing in

clear water. Dry well with a soft cloth.

NOTE: Do not use enzyme washing powder, harsh

abrasives or chemical oven cleaners of any kind.

Oven Fittings

The oven shelves can be cleaned either in a

dishwasher or by using a fine steel wool soap pad.

The grill and meat pans can be cleaned in warm

soapy water using a fine steel wool soap pad to

remove stubborn stains or in a dishwasher.

They should be cleaned after each use.

Oven Interiors

To clean the oven interiors remove all the oven

fittings and where applicable the 'Stay Clean' liners.

All types of oven cleaners can be used, but

do notdo not

do not

allow abrasive cleaners or oven spray to come into

contact with the 'Stay Clean' liners. Use a fine steel

wool soap pad to remove stubborn stains.

Oven Door Cleaning

The inner door glass panel can be removed for

easy cleaning, see “Care and Cleaning”.

Cooker Exterior

The outside of the cooker should be cleaned regularly

to keep it looking like new. Wipe over with a soft cloth

wrung out in warm water and dry with a soft clean

cloth. You can use mild non abrasive cleaners but

always read the manufacturer's instructions first.

Always test their suitability on a small area of the

cooker not noticeable in normal use.

NOTE: DO NOT use scouring pads or abrasive

cleaners as they may scratch the surface.

Wear protective gloves when cleaning any part of

your cooker.

Cleaning the glass door*

Open the door fully and

carefully slide the first

inner glass towards you,

taking care not to allow

the glass to fall.

If necessary, the glass

can be pushed delicately

from the back side.

Repeat the same

procedure with the next

glass.

Now the external glass

panel can be washed.

WARNING! As soon as the inner and middle glass

panels are removed , the door slams shut.

SIDE OPENING DOORS

Cleaning the door glass

is the same as the drop

down doors, except take

care to support the

weight of the inner glass

when removing and

refitting.

The glass panel may now

be washed at the sink.

Stubborn stains can be

removed by using a fine

steel wool soap pad.

*Available only in certain models.

! Never use steam cleaners or pressure cleaners

on the appliance.

Clean the glass part of the oven door using a sponge

and a non-abrasive cleaning product, then dry

thoroughly with a soft cloth. Do not use rough abrasive

material or sharp metal scrapers as these could

scratch the surface and cause the glass to crack.

! The accessories can be washed like everyday

crockery (even in your dishwasher).

! Switch off the electricity supply and allow to

cool before cleaning the cooker.

! Clean the cooker regularly and wipe up spills

soon after they occur to prevent them from

becoming burnt on. Never use biological

washing powder, caustic cleaners, harsh

Care and Cleaning

Ensure the glass panel is not subjected toEnsure the glass panel is not subjected to

Ensure the glass panel is not subjected to

any sharp mechanical blows. any sharp mechanical blows.

any sharp mechanical blows. Take particular

care not to damage the inner surface which is coated

with a heat reflective layer. After cleaning, rinse and

dry with a soft cloth. For slight soiling the inner glass

panel may be cleaned, while still warm, without

removing it from the door.

Warning: Oven must not be operated with inner door

glass removed.

To reassemblethe oven

doors proceed with

inserting the glass

pannels in the reverse

order, pushing gently

every panel directly into

the liners.

BE CAREFUL NOT TO

DAMAGE THE GLASS

PANELS BY PUSHING

THEM TOO HARD.

When refitting the glass make sure it is fitted

correctly i.e. reflective face is fitted the right way

round.

abrasives, scouring pads, steam cleaners,

aerosol cleaners or oven chemical cleaners of

any kind.

! If it is necessary to remove the cooker for

cleaning, ensure that it is cool and beware that

it is heavy (approximately 70 kg 155 lbs).

! To move the cooker forward, open the top oven/

grill door and with both hands positioned under the

roof of the compartment, lift and pull forward.

Replace by pushing the cooker backwards.

! Check that the cooker is level. Take care not to

damage any floor coverings.

OVEN HEAT CLEAN LININGS

The oven side linings are coated with a special

enamel which has a continuous cleaning action.

The higher the oven temperature the more effective the

action. In most cases this cleaning operation will

proceed during normal cooking. However, if roasting is

done frequently, or high temperatures are not used

regularly, it may be necessary to occasionally operate

the oven empty at Mark 8 for about an hour.

It should not normally be necessary to clean the

linings with water, but if desired, wipe them over with a

soapy cloth, followed by a wipe with a damp clean

cloth.

REPLACEMENT OF OVEN LIGHT

BULB

CAUTION: DISCONNECT THE APPLIANCE

FROM THE ELECTRICITY SUPPLY BEFORE

REPLACING THE LAMP TO AVOID THE

POSSIBILITY OF AN ELECTRIC SHOCK.

Light bulbs are not covered by the manufacturer's

guarantee.

A new 25W, 300°C rated SES bulb can be obtained

from your cooker supplier or any major electrical

retailer.

1. Remove the shelves from the oven.

2. Unscrew the lens using a thick cloth to protect your

fingers in the unlikely event of a lens fracture.

3. Unscrew bulb.

4. Fit new bulb and refit lens.

Care and Cleaning

COO,./FI0I12 C3.40I0GM.T2O5

6itreous.namel

Door inner panels, pan supports, burner caps,

roasting dish, grill pan, main oven base, inside of

grill compartment.

Hotplate

Cloth wrung out in warm soapy water. Stubborn stains can be

removed with a cream paste, liquid cleaner or by rubbing with fine

steel wool soap pads.

Check that the cleaning agent is approved by the Vitreous Enamel

Association.

Paint

Side panels.

Control panel, lid front trim

Wash with a cloth wrung out in warm soapy water only.

DO NOT USE ABRASIVES.

4luminium

Hotplate burner bodies, lid rear trim.

Similar to paint cleaning above. Use a nylon brush to remove any

cleaning materials, water or dirt from the hotplate burner bodies.

Glass

As for enamel cleaning. Polish with a clean dry cloth or kitchen roll.

ChromiumPlating

Oven shelves, grill pan grid, grill pan handle

support.

Wipe with a cloth wrung out in warm soapy water. A fine steel wool

soap pad e.g. Brillo, Ajax, or a chrome or stainless steel cleaner

may be used.

Plasti7

Control knobs.

Wipe with a cloth wrung out in warm soapy water.

1tainle s s 1teel

Hotplate, control panell, grill pan handle,

Wipe with a cloth wrung out in warm soapy water. Polish with a

clean dry cloth or kitchen towel. For stubborn stains, use a

proprietary stainless steel cleaner and follow the instructions on the

container.

CLEANING THE DOORS*

SIDE OPENING DOORS

Cleaning the door glass is the same as the drop

down doors,except take care to support the weight of

the inner glass when removing and refitting.

DROP DOWN DOORS

Remove the door inner glass as follows.

1. Open the door fully and unscrew the two screws

securing the glass panel so that the securing

brackets can be turned.There is no need to remove

the screws completely.

2. Turn the brackets so that the glass can be removed

and cleaned at the sink (Fig. 1.)

3. The inside of the outer door glass can now be

cleaned while still fitted to the cooker.

NEVER OPERATE THE COOKER

WITHOUT THE INNER DOOR GLASS IN

POSITION.

Refit the door inner glass as follows.

1. NOTE: The inner door glass has a special reflective

coating on one side. Replace the door inner glass

so that the statement: "IMPORTANT THIS FACE

TOWARDS THE OVEN" can be read from the inner

side of the door.

2. Turn the two securing brackets back to their original

position to retain the glass and tighten the screws.

(Fig. 2.)

*Available only in certain models.

Before contacting your Service Centre or

Installer, check the problem guide below, there

may be nothing wrong with your cooker.

Something Wrong

with your Cooker?

RLE#HEK

Burner will not light: If all burners fail to ignite

Check that sparks appear at the burners; a clicking noise should

be heard.

If not;

Check that the electricity supply is turned on.

If the electricity supply has failed, all burners can be lit by a match.

If only one burner fails to ignite

Check that the burner is dry and that spillage of food or cleaning

fluid remains are not affecting the ignitor or burner ports.

Clean away any debris with a dry nylon brush such as an old

toothbrush. If a wire wool pad has been used for cleaning around

the burner ensure the ignitor is free from any stray strands. Any

water on the burner should be dried with a cloth or kitchen towel.

On the hotplate make sure that all the burner parts are correctly

seated.

Slight odour or small amount of smoke when grill /

oven used first time.

This is normal and should cease after a short period.

Oven cooks too fast or too slow. Check that the gas mark and shelf positions are as recommended

in the Oven Cooking Charts. However, it may be necessary to

increase or decrease the recommended setting slightly to suit your

taste.

Cannot set an "Auto Cook" programme or cannot

get the timer to turn the oven on or off at the

required times.

Read the Timer instructions in this book carefully remembering that

the Cook period is the length of time that the timer will switch the

oven(s) on as part of an Auto Cooking Programme.

Timer Display shows "0:00" with "Auto" Flashing. The electricity supply to the cooker may have been been

interrupted, but has now come back on again. Set the correct time

of day by following the instructions given in the timer section of this

book.

Main oven does not work, but the grill, top oven

and hotplate burners work.

The timer may be set for an Auto Cooking Programme. Check the

timer to see if "AUTO" is illuminated. If it is, follow the instructions

given in the timer section of this book to cancel the Auto Cooking

Programme.

Oven lamp does not work. The oven lamp is not covered by the guarantee. The part is easily

changed (see the section on oven lamp replacement).

A new lamp may be obtained from our Parts department, (see back

page).

Page is loading ...

Hotpoint DSD60S.0 Dual Fuel Cooker User manual

Brand: Hotpoint

Model: DSD60S.0 Dual Fuel Cooker

Category: Microwaves

Type: User manual

This manual is also suitable for

Download PDF

report

Hotpoint DSD60S.0 Dual Fuel Cooker User manual

This manual is also suitable for

Hotpoint DSD60S.0 Dual Fuel Cooker User manual

Related papers

Other documents