Premier 120579LF Installation guide

Premier
Brand
Premier
Model
120579LF
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

2. Place a ring of putty around drain
opening of sink.
1. Remove old pop-up drain assembly.
6. Place one end of spring clip on end
of ball rod. Pass the tip of the rod
through the hole in the lift rod strap
and then through the hole on the
other end of the spring clip .
3. Insert threaded end of drain body up
through drain hole and attach flange to
body.
4. Thread lock nut from underside of
sink until rubber washer sits securely
inside opening of sink. Tighten lock
nut.
5. Insert main plunger into drain. Insert
ball rod into rod port and into hole at
bottom of main plunger.
7. Insert bottom of lift rod into hole at top
of lift rod strap. Tighten with thumb
screw.
Two Handle Mini Widespread Lavatory Faucet
Pop-up Drain Installation
Replacement Parts/Repuestos
120579/120580/120581
120579LF/120580LF/120581LF
Model number:
Customer Service
For additional assistance,
service or parts for your
Premier Faucet,
Call 1-866-745-4010. or visit
Website: www. premierfaucet. com
TOOLS:
CLEANING:
Philips screwdriver Pliers Pipe tape
Adjustable wrench Hex wrench
Sonoma
INSTALLATION STEPS:
Warning and Notes:
Check with local plumbing code requirements before installation; This product should be installed by a local licensed plumber; To meet EPA requirements,
replace original aerator after flushing lines.
9.
10.
8.
13.
2.
3.
4.
6.
5.1
5.2
1.1
1.2
7.
14.
15.
11.
12.
1.1 Index Button - Cold A66D957C
1.2 Index Button - Hot A66D957H
2 Metal Handle Assembly A66E457
3 Retainer Nut A016026
4 Handle Trim Ring A66F141
5.1 Ceramic Disc Cartridge - Cold A507072W
5.2 Ceramic Disc Cartridge - Hot A507071W
6 Handle Valve Body A661002W
7 Mounting Hardware Assembly A66D900
8 Spout Assembly A666266N
9 Spout Trim Ring A667063
10 Mounting Hardware A603642
11 "+" Adaptor A105759N
12 Lock Nut A009015
13 Aerator A500872N-51
14 Lift Rod A025575
15 Pop-up Assembly A556200L
5. Tighten end of shank with wrench
and slip coupling nut onto inlet port.
3. Place the handle body through
hole. Re-assemble the parts
and screw with lock nut.
2. Remove assembled parts from
handle body.
1. Apply silicone sealant around
bottom of spout. Place spout in
center hole of sink. Secure with
pictured parts.
6. Tighten the hose with water
supply.
4.Insert the quick connector to the
spout valve, and then connect the
other end to the handle valve. A
connection is secure when a “click”
is heard, and the connector cannot
be pulled off from the valve.
Note: If you need to loosen the
connector, press the lip before
loosening.
7. After installing faucet, remove aerator
and turn on water to remove any
left of debris. Re-assemble aerator.
Lift rod
Thumb screw
Lift rod strap
Ball rod
Main plunger
Spring clip
Flange
Lock nut
Friction ring
Ball nut
  • Page 1 1

Premier 120579LF Installation guide

Premier
Brand
Premier
Model
120579LF
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents