Grizzly Industrial G0707 Owner's manual

Brand: Grizzly Industrial

Model: G0707

Type: Owner's manual

MODEL G0707

24" X 37" BLAST CABINET

OWNER'S MANUAL

(For models manufactured since 01/15)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#CR12334 PRINTED IN CHINA.

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

INTRODUCTION ............................................................................................................................... 2

Manual Accuracy ........................................................................................................................ 2

Contact Info ................................................................................................................................ 2

Machine Description ................................................................................................................... 2

Identification ............................................................................................................................... 3

Data Sheet ................................................................................................................................. 4

Machine Data Sheet ................................................................................................................... 4

SECTION 1: SAFETY ....................................................................................................................... 6

Safety Instructions for Machinery ............................................................................................... 6

Additional Safety for Blast Cabinets ........................................................................................... 8

SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 9

110V Operation .......................................................................................................................... 9

SECTION 3: SETUP ....................................................................................................................... 10

Needed for Setup ..................................................................................................................... 10

Unpacking ................................................................................................................................ 10

Inventory ................................................................................................................................... 11

Hardware Recognition Chart .................................................................................................... 12

Site Considerations .................................................................................................................. 13

Mounting to Shop Floor ............................................................................................................ 14

Air Supply Setup ...................................................................................................................... 15

Assembly .................................................................................................................................. 16

Test Run ................................................................................................................................... 19

SECTION 4: OPERATIONS ........................................................................................................... 20

Preparation ............................................................................................................................... 20

Control Panel............................................................................................................................ 21

Basic Operation ........................................................................................................................ 22

Blasting Media .......................................................................................................................... 25

SECTION 5: ACCESSORIES ......................................................................................................... 28

SECTION 6: MAINTENANCE......................................................................................................... 29

Schedule .................................................................................................................................. 29

Cleaning ................................................................................................................................... 29

SECTION 7: SERVICE ................................................................................................................... 30

Troubleshooting ........................................................................................................................ 30

Filter Replacement ................................................................................................................... 31

Motor Brush Replacement ....................................................................................................... 32

SECTION 8: WIRING ...................................................................................................................... 35

Wiring Safety Instructions ........................................................................................................ 35

Control Box Wiring Diagram ..................................................................................................... 36

Components Wiring Diagram ................................................................................................... 37

Electrical Component Locations ............................................................................................... 38

Air System Diagram ................................................................................................................. 39

SECTION 9: PARTS ....................................................................................................................... 40

Parts List .................................................................................................................................. 41

Label Placement & Parts List ................................................................................................... 42

WARRANTY AND RETURNS ........................................................................................................ 45

Table of Contents

-2-

Model G0707 (Mfd. Since 01/15)

INTRODUCTION

This blast cabinet is designed for high-use media

blasting operations, where air flow up to 25 CFM

and air pressure up to 120 PSI can be used. Air

pressure is fully adjustable with a control panel

air pressure regulator. A fixed blasting gun and

a hand-held blasting gun are included in this

machine. Blasting operations through a hand-held

blast gun or fixed gun are controlled by a foot

valve and control panel.

An internal set of fluorescent work lamps provide

illumination during blasting operations, and a

built-in dust collector maintains blasting environ-

ment visibility. The cabinet is equipped with two

side loading doors for ease of workpiece loading

and unloading. Media is quickly unloaded through

the hopper dump port door, and reloaded through

a side door.

Machine Description

We stand behind our machines! If you have ques-

tions or need help, contact us with the information

below. Before contacting, make sure you get the

serial number

and manufacture date

from the

machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Contact Info

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that

sometimes the machine

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something

check our

website for an updated version. W

e post

current

manuals and

manual updates for free

on our web-

site at

www.grizzly.com.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write down

the

Manufacture Date and Serial Number

from

the machine ID label (see below). This information

is required for us to provide proper tech support,

and it helps us determine if updated documenta-

tion is available for your machine.

Manufacture Date

Serial Number

Manual Accuracy

Model G0707 (Mfd. Since 01/15)

-3-

Figure 1. Features and controls.

Identification

A. Control Panel

B. Pressure Regulator w/Gauge

C. Dust Collector

D. Fluorescent Lamp Assembly

E. Canister Plunger for Filter Cleaning

F. Side-Loading Door

G. Door Latch

H. Hopper Dump Chute

I. Gloves

J. Foot Pedal Blasting Switch

K. Heavy Duty Leg Support System

L. Viewing Window

-4-

Model G0707 (Mfd. Since 01/15)

Data Sheet

Machine Data Sheet

model G0707

24" x 37" BlAST cABineT

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

mAcHine dATA

SHeeT

Product Dimensions:

Width ..................................................................................................................................................................................... 41"

Depth ..................................................................................................................................................................................... 36"

Height ..................................................................................................................................................................................64

⁄2"

Foot Print (Length/Width) .......................................................................................................................................... 23" x 36

⁄4"

Weight ........................................................................................................................................................................... 198 lbs.

Shipping Dimensions:

Type ...........................................................................................................................................................................Cardboard

Content .......................................................................................................................................................................... Machine

Weight ............................................................................................................................................................................ 231 lbs.

Length/Width/Height ............................................................................................................................................52" x 39" x 30"

Electrical:

Switch ........................................................................................................................................Sealed ON/OFF Rocker Switch

Switch Voltage ................................................................................................................................................................... 110V

Cord Length ..........................................................................................................................................................................6 ft.

Cord Gauge .................................................................................................................................................................18 gauge

Recommended Circuit Size ............................................................................................................................................15 amp

Plug .......................................................................................................................................................................................Yes

Number of Lamps .....................................................................................................................................................................2

Lighting Type ............................................................................................................................................. 18 Watt Fluorescent

Dust Collector Motor:

Type ....................................................................................................................................................................Universal Type

Horsepower ......................................................................................................................................................................1

⁄2 HP

Voltage ............................................................................................................................................................................... 110V

Phase ................................................................................................................................................................................Single

Amps .................................................................................................................................................................................... 11A

Cycle ................................................................................................................................................................................. 60 Hz

Number Of Speeds ...................................................................................................................................................................1

Power Transfer ........................................................................................................................................................Direct Drive

Bearings ............................................................................................................................... Shielded and Permanently Sealed

Operation Information:

Suggested Operating Air Pressure Range .................................................................................................................60-80 PSI

Maximum Air Pressure ...................................................................................................................................................120 PSI

Recommended Air Supply ..........................................................................................................................................5-28 CFM

Maximum Abrasive Capacity .........................................................................................................................................400 lbs.

Suggested Abrasive Capacity .......................................................................................................................................... 55 lbs.

Abrasive Type ...............................................................................................................................................................Dry Only

Load & Unload Access ......................................................................................................................................................Sides

Design Type .............................................................................................................................................................Floor Model

Model G0707 Page 1 of 2

Model G0707 (Mfd. Since 01/15)

-5-

General Specifications:

Body Construction ............................................................................................................................. Welded Heavy-Duty Steel

Dust Collector Filter Dimensions ..................................................................................................................6

⁄4" Dia. x 12" Tall

Dust Collector Filter Type ...............................................................................................................................................Pleated

Dust Collector Filter Rating ......................................................................................................................................... 5 Microns

Paint. ......................................................................................................................................... Powder Coated Inside and Out

Other Specifications:

Country Of Origin .............................................................................................................................................................. China

Warranty ........................................................................................................................................................................... 1 Year

Serial Number Location ..............................................................................................ID Label on Front Center of the Cabinet

Assembly Time .........................................................................................................................................................60 Minutes

Features:

Dual Side Loading Doors

Panel Mounted Electric and Air Controls

Spare Blast Tips

Spare Window Protection Sheets

Included Dust Collector Filter

Screened Work Table

Foot Pedal Blasting Control

Gun Blasting System

Hands-Free Blasting System

Hopper Dump Gate

Easy-Clean Dust Collector

Reusable Dust Collector Filter Element

External Lighting System

Model G0707 Page 2 of 2

-6-

Model G0707 (Mfd. Since 01/15)

ELECTRICAL EQUIPMENT INJURY RISKS. You

can be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE making

adjustments, changing tooling, or servicing machine.

This prevents an injury risk from unintended startup

or contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

This symbol is used to alert the user to useful information about

proper operation of the machine.

NOTICE

Safety Instructions for Machinery

SECTION 1: SAFETY

Model G0707 (Mfd. Since 01/15)

-7-

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to reduce

risk of slipping and losing control or accidentally

contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery

operations may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece mate-

rial. Always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly BEFORE

operating machine.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine

for damaged, loose, or mis-adjusted parts—or

any condition that could affect safe operation.

Immediately repair/replace BEFORE operating

machine. For your own safety, DO NOT operate

machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

-8-

Model G0707 (Mfd. Since 01/15)

Additional Safety for Blast Cabinets

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

Failure to do so could result in serious per-

sonal injury, damage to equipment, or poor

work results.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine

with respect and caution to decrease the

risk of operator injury. If normal safety pre-

cautions are overlooked or ignored, serious

personal injury may occur.

5. WORK AREA SAFETY. To prevent acci-

dental contamination of shop air, clean dust

collector and filters often, and repair any

suction hose leaks immediately.

6. MAINTAINING COMPONENTS. To pre-

vent accidental contamination or blast inju-

ry, replace tips, hoses, lenses, and gloves

when they become worn.

7. SAFE MEDIA BLASTING. Do not use sys-

tem over the rated PSI or lines and seals

may burst and cause injury.

8. CORRECT LIGHTING. To prevent ballast

overload and possible fire, do not install

lamps that use over 18 watts.

9. LOADING & UNLOADING. To prevent

accidental blasting injury, disconnect the

air supply before loading or unloading the

workpiece from the blast cabinet.

10. SAFE MAINTENANCE. To prevent acci-

dental blasting injury or shock, disconnect

air supply and power before doing mainte-

nance.

11. SAFE MEDIA BLASTING. To prevent dust

exposure, always secure the door(s) before

beginning media blasting operations.

1. PERSONAL PROTECTION EQUIPMENT.

Media blasting presents a real hazard of

silicosis and other lung contamination inju-

ries! These injuries are permanent and can

get worse over time. If you use media blast-

ing equipment without the proper head-

gear, eye protection, and respirator, your

lungs and eyes may become permanently

damaged. DO NOT use this blast cabinet

unless you know how to use it. Protect

yourself correctly, and keep all unprotected

bystanders away. For latest types of protec-

tive equipment and acceptable respirator

types, contact your local OSHA or NIOSH

office.

2. LEAVING THE AREA. To prevent acci-

dental blasting injury, disconnect air supply

when leaving the blast cabinet.

3. MAINTAINING MACHINE. To prevent acci-

dental contamination of shop air, check the

blast cabinet for any leaks before use, and

reseal immediately.

4. SAFE ENVIRONMENT. To avoid media

escaping from the cabinet or to prevent an

entrapment hazard for animals or children,

always close and latch shut the blast cabi-

net doors when not in use.

Model G0707 (Mfd. Since 01/15)

-9-

Figure 2. Typical 5-15 plug and receptacle.

Grounding Prong

Neutral Hot

5-15 PLUG

GROUNDED

5-15 RECEPTACLE

110V Operation

Full Load Amperage Draw

This machine draws the following amps under

maximum load:

Amp Draw .............................................. 11 Amps

Power Supply Circuit Requirements

Both the machine and the power supply circuit

must be properly grounded. The power supply cir-

cuit must be rated for the amperage given below.

Never replace a circuit breaker on an existing cir-

cuit with one of higher amperage without consult-

ing a qualiﬁed electrician to ensure compliance

with wiring codes. If you are unsure about the

wiring codes in your area or you plan to con-

nect your machine to a shared circuit, consult

a qualified electrician.

Minimum Circuit Size ............................. 15 Amps

This machine MUST have a ground prong in

the plug to help ensure that it is grounded.

DO NOT remove ground prong from plug

to fit into a two-pronged outlet! If the plug

will not fit the outlet, have the proper outlet

installed by a qualified electrician.

Extension Cords

We do not recommend using extension cords, but

if you find it absolutely necessary:

• Use at least a 14 gauge cord that does not

exceed 50 feet in length!

• The extension cord must have a ground wire

and plug pin.

• A qualified electrician MUST size cords over

50 feet long to prevent motor damage.

SECTION 2: CIRCUIT REQUIREMENTS

Serious personal injury could occur if you

connect the machine to power before com-

pleting the setup process. DO NOT connect

the machine to the power until instructed

later in this manual.

Power Connection Device

This machine comes with a plug, similar to Figure

2, to connect the machine to power.

Electrocution or fire could

result if machine is not

correctly grounded or

connected to the power

source. Get help if you

do not know what you are

doing.

-10-

Model G0707 (Mfd. Since 01/15)

Wear safety goggles dur-

ing the entire setup pro-

cess!

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

SECTION 3: SETUP

The following are needed to complete the setup

process, but are not included with your machine.

Description Qty

• Safety Goggles for Each Person ................ 1

• Forklift ......................................................... 1

• Wrench 10mm ............................................ 1

• Additional People (For Lifting) .................... 1

• Screwdriver Phillips #2 ............................... 1

• Wrench or Nut Driver

⁄8" ............................ 1

• Exterior-Grade Silicone Caulking ...... 1 Tube

Needed for Setup

Your machine was carefully packaged for safe

transportation. Remove the packaging materials

from around your machine and inspect it. If you

discover the machine is damaged, please imme-

diately call Customer Service at (570) 546-9663

for advice.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

Unpacking

This machine and its com-

ponents are very heavy.

Get lifting help or use

power lifting equipment

such as a forklift to move

heavy items.

Model G0707 (Mfd. Since 01/15)

-11-

Inventory

The following is a description of the main compo-

nents shipped with your machine. Lay the compo-

nents out to inventory them.

Note: If you can't find an item on this list, check

the mounting location on the machine or examine

the packaging materials carefully. Occasionally

we pre-install certain components for shipping

purposes.

Box 1: (Figure 3) Qty

A. Dust Collector Assembly w/Filter ............... 1

B. Cabinet ....................................................... 1

C. Spare Door Seal

⁄8" x 1" x 79" ................... 1

D. Teflon Tape ................................................. 1

E. Legs ............................................................ 4

F. Left Door..................................................... 1

G. Right Door .................................................. 1

H. Side Leg Supports...................................... 2

I. Blast Tip Set ............................................... 1

—Blast Tip 6mm ID .................................... 2

— Blast Tip 7mm ID .................................... 2

J. Canister Plunger Assembly ........................ 1

K. Hopper Chute Door .................................... 1

L. Push-on Hose Adapter

⁄8" .......................... 1

M. Lever and Latch Set (for 2-Doors) .............. 1

N. Viewing Window Dust Sheets 23

⁄2" x 10" . . 5

O. Lamp Window Dust Sheets 21

⁄2" x 4" ....... 5

P. Bolt Bag ...................................................... 1

—Cabinet Screws

⁄4-20 x

⁄2" ................... 26

— Flange Nuts

⁄4"-20 ................................ 26

If any nonproprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

SUFFOCATION HAZARD!

Immediately discard all plas-

tic bags and packing materi-

als to eliminate choking/suf-

focation hazards for children

and animals.

Figure 3. Inventory.

-12-

Model G0707 (Mfd. Since 01/15)

5mm

Hardware Recognition Chart

Model G0707 (Mfd. Since 01/15)

-13-

Site Considerations

Weight Load

Refer to the

Machine Data Sheet for the weight

of your machine. Make sure that the surface upon

which the machine is placed will bear the weight

of the machine, additional equipment that may be

installed on the machine, and the heaviest work-

piece that will be used. Additionally, consider the

weight of the operator and any dynamic loading

that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will

be processed through this machine and provide

enough space around the machine for adequate

operator material handling or the installation of

auxiliary equipment. With permanent installations,

leave enough space around the machine to open

or remove doors/covers as required by the main-

tenance and service described in this manual.

See below for required space allocation.

Physical Environment

The physical environment where the machine is

operated is important for safe operation and lon-

gevity of machine components. For best results,

operate this machine in a dry environment that is

free from excessive moisture, hazardous chemi-

cals, airborne abrasives, or extreme conditions.

Extreme conditions for this type of machinery are

generally those where the ambient temperature

range exceeds 41°–104°F; the relative humidity

range exceeds 20%–95% (non-condensing); or

the environment is subject to vibration, shocks,

or bumps.

Electrical Installation

Place this machine near an existing power source.

Make sure all power cords are protected from

traffic, material handling, moisture, chemicals, or

other hazards. Make sure to leave enough space

around machine to disconnect power supply or

apply a lockout/tagout device, if required.

Lighting

Lighting around the machine must be adequate

enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract

or impede the operator must be eliminated.

Children or untrained people

may be seriously injured by

this machine. Only install in an

access restricted location.

Figure 4. Space required for full range of movement.

81"

22"

35"

-14-

Model G0707 (Mfd. Since 01/15)

Although not required, we recommend that you

mount your new machine to the floor. Because

this is an optional step and floor materials may

vary, floor mounting hardware is not included.

Generally, you can either bolt your machine to

the floor or mount it on machine mounts. Both

options are described below. Whichever option

you choose, it is necessary to level your machine

with a precision level.

Bolting to Concrete Floors

Lag shield anchors with lag bolts (Figure 5) and

anchor studs are two popular methods for anchor-

ing an object to a concrete floor. We suggest

you research the many options and methods for

mounting your machine and choose the best that

fits your specific application.

Mounting to Shop

Floor

Figure 6. Machine mount example.

Using Machine Mounts

Using machine mounts, shown in Figure 6, gives

the advantage of fast leveling and vibration reduc-

tion. The large size of the foot pads distributes

the weight of the machine to reduce strain on the

floor.

Figure 5. Typical fasteners for mounting to

concrete floors.

NOTICE

We strongly recommend securing your

machine to the floor if it is hardwired to the

power source. Consult with your electrician

to ensure compliance with local codes.

NOTICE

Anchor studs are stronger and more per-

manent alternatives to lag shield anchors;

however, they will stick out of the floor,

which may cause a tripping hazard if you

decide to move your machine.

Model G0707 (Mfd. Since 01/15)

-15-

Air Supply Setup

The ability of this blast cabinet to accomplish its

task is directly related to how well the air supply

system is designed. For this blast cabinet to oper-

ate at its maximum potential with the largest blast

tip, the CFM feeding the regulator should be 35

CFM at 120 PSI.

Refer to your compressor Owner’s Manual and

make sure that the compressor can handle the

load of a blasting cabinet. Often a 5 HP compres-

sors are used, but the duration of the work shift

and tip size installed must be reduced so the

compressor duty cycle is not exceeded. Ignoring

this requirement could lead to compressor over-

heating and failure. The rule of thumb is that, the

smaller the compressor, the less CFM available,

and greater cool-down time required.

If this blast cabinet is to be used at full capacity

in eight-hour work shifts at the maximum air pres-

sure of 120 PSI using the largest tip, an industrial-

grade compressor capable of delivering up to 35

CFM may be required.

For smaller compressors, make sure to increase

the compressor maintenance interval and verify

that your compressor has the best cooling airflow

possible.

When filling or servicing the blast cabinet, there

is a risk of subjecting the compressor to airborne

media or dust. Be sure to locate the blast cabinet

away from the compressor operating environment.

If even small amounts of fine media dust enter the

compressor through the intake or during general

service, rings, pistons, valves, and bearings can

be quickly destroyed.

Remove any in-line oilers, make the supply line

long enough to allow the compressed air to fully

cool before it reaches the gun, and install an

in-line water separator or air dryer. Tilt air sup-

ply lines slightly back toward the compressor so

residual condensation in the lines will run back to

the tank instead of the media blasting unit. For a

general summary of the typical air system of this

blast cabinet and supply system, refer to the Air

System Diagram on Page 39.

If using an existing air system, eliminate air supply

restrictions and pressure drops that may occur at

small quick-disconnect fittings, elbows, small sup-

ply piping, undersized water separators, kinked

lines, or rust-filled piping.

Typically, when installing a new supply line for the

blast cabinet with a 125 foot run or less, the air

supply line up to the regulator inlet should have

an inside diameter of

⁄4". For runs up to 300', a

supply line with a 1" inside diameter is recom-

mended.

If an air compressor is not available or the blast

cabinet is to be used at a remote location, NEVER

connect this blast cabinet to pressurized bottled

gasses such as oxygen bottles used in welding

operations. Line ruptures or explosions can occur,

causing equipment damage, serious injury, or

death.

Make sure to install an air supply quick-discon-

nect fitting or a shut-off valve that can be locked

out to prevent the air pressure from accidentally

being turned on. These items allow for the blast

cabinet to be serviced safely or allow it to sit idle

when not in use.

-16-

Model G0707 (Mfd. Since 01/15)

Assembly

To assemble the blast cabinet:

1. With the help of an assistant, lay a sheet of

cardboard on the floor to protect the media

blasting cabinet, and place the cabinet on its

back.

2. Using a #2 Phillips screwdriver, fasten all four

legs to the underside of the cabinet with (16)

⁄4-20 x

⁄2" cabinet screws and flange nuts

(Figure 7).

3. Attach the two side supports (Figure 7) to

the left and right set of legs with four cabinet

screws and flange nuts.

4. With the help of an assistant, stand the blast

cabinet upon the legs.

Figure 7. Leg installation.

Side

Support

Figure 8. Hopper chute door.

5. Using three Phillips screws and flange nuts,

fasten the hopper chute door to the hopper,

as shown in Figure 8. When secured, latch

the hopper door closed.

6. Using a Phillips screwdriver, remove the suc-

tion port baffle (Figure 9).

Figure 9. Suction port baffle.

Model G0707 (Mfd. Since 01/15)

-17-

15. Re-install the baffle and install both side

doors with the eight M5-.8 x 10 flat head

screws and hex nuts already in the cabinet.

16. Verify that a plastic dust sheet is affixed to

the inside of the cabinet viewing window and

the lamp window (Figure 13).

Figure 12. Dust collector suction port.

7. Using four cabinet screws and flange nuts,

fasten the dust collector to the rear of the

cabinet, so the suction port protrudes through

the hole cut into the back of the cabinet

(Figure 10).

8. Plug the dust collector into the in-line power

supply plug protruding from the control box

(Figure 10).

9. Unlatch the dust collector motor (Figure 10),

lift the dust collector out of the canister, and

set it aside.

10. Working from inside of the canister, insert the

canister plunger through the canister wall so

it can be seen protruding from the outside of

the canister.

Figure 10. Dust collector.

12. Re-install the dust collector into the canister.

13. Using a 10mm wrench, tighten the jam nut

against the knob.

14. Using silicone (not supplied), seal the gap

between the suction port and the hole in the

cabinet wall (Figure 12).

Figure 11. Canister plunger.

11. Place the spring on the plunger shaft, and

thread the jam nut and knob onto the plunger

as shown in Figure 11.

Knob Jam Nut

Spring

and

Plunger

Gap

In-line Plug

-18-

Model G0707 (Mfd. Since 01/15)

17. Using the fasteners already in the cabinet

and doors, install the doors, then receivers,

and adjust the receivers so the doors slightly

compress the foam seal when closed (Figure

14).

Figure 14. Door latched closed.

Figure 13. Viewing window and lamp window.

18. Route the blasting guns and hoses to elimi-

nate any kinks or binds (Figure 15).

Figure 15. Blast gun and hose positioning.

19. Position the foot pedal (Figure 16) between

the legs where it will be convenient to use.

The pedal may also be fastened to the floor if

the unit will not be moved.

Figure 16. Foot pedal positioning.

20. Pour the desired amount of media into the

cabinet through one of the side doors. DO

NOT overfill.

21. Wait 24 hours for the silicone sealant to fully

setup and dry. Otherwise, when the machine

is turned on and media blasting begins, the

seal may be broken, causing leakage.

22. Inspect all seals, hose clamps, glove clamps,

and window seals for any potential leaks.

Correct as required.

Dust

Sheets

Receiver

Page is loading ...

Grizzly Industrial G0707 Owner's manual

Brand: Grizzly Industrial

Model: G0707

Type: Owner's manual

Download PDF

report

Grizzly Industrial G0707 Owner's manual

Grizzly Industrial G0707 Owner's manual

Related papers

Other documents