ENFORCER SK-1123-FDQ Installation guide

Brand: ENFORCER

Model: SK-1123-FDQ

Type: Installation guide

ENFORCER SK-1123-FDQ is a vandal-resistant flush-mount access control keypad that provides direct access to programming (DAP), allowing users to easily modify settings without the need for special tools or software. It features programmable door-propped-open warnings and timing, egress delay/warning, and output relay activation sounds, making it a versatile solution for a variety of access control applications. Additionally, the keypad complies with FCC regulations and offers a limited warranty for added peace of mind.

SK-1123-FDQ

Vandal Resistant Flush-Mount

Access Control Keypad

Manual

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

FCC COMPLIANCE STATEMENT: 7KLVGHYLFHFRPSOLHVZLWKSDUWRIWKH)&&5XOHV2SHUDWLRQLVVXEMHFWWRWKH

following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

LIMITED WARRANTY: 7KLV6(&2/$50SURGXFWLVZDUUDQWHGDJDLQVWGHIHFWVLQPDWHULDODQGZRUNPDQVKLSZKLOH

XVHGLQQRUPDOVHUYLFHIRUWKUHH\HDUVIURPWKHGDWHRIVDOHWRWKHRULJLQDOFXVWRPHU6(&2/$50¶VREOLJDWLRQLVOLPLWHGWR

WKHUHSDLURUUHSODFHPHQWRIDQ\GHIHFWLYHSDUWLIWKHXQLWLVUHWXUQHGWUDQVSRUWDWLRQSUHSDLGWR6(&2/$507KLV:DUUDQW\

is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

LPSURSHURUDEQRUPDOXVDJHRUIDXOW\LQVWDOODWLRQRULIIRUDQ\RWKHUUHDVRQ6(&2/$50GHWHUPLQHVWKDWVXFKHTXLSPHQW

is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of

6(&2/$50DQGWKHSXUFKDVHU¶VH[FOXVLYHUHPHG\VKDOOEHOLPLWHGWRWKHUHSODFHPHQWRUUHSDLURQO\DW6(&2/$50¶V

RSWLRQ,QQRHYHQWVKDOO6(&2/$50EHOLDEOHIRUDQ\VSHFLDOFROODWHUDOLQFLGHQWDORUFRQVHTXHQWLDOSHUVRQDORUSURSHUW\

damage of any kind to the purchaser or anyone else.

NOTICE:7KH 6(&2/$50 SROLF\ LV RQH RI FRQWLQXDO GHYHORSPHQW DQG LPSURYHPHQW )RU WKDW UHDVRQ 6(&2/$50

UHVHUYHVWKHULJKWWRFKDQJHVSHFL¿FDWLRQVZLWKRXWQRWLFH6(&2/$50LVQRWUHVSRQVLEOHIRUPLVSULQWV7UDGHPDUNVDUHWKH

SURSHUW\RI6(&2/$5086$,QFRUWKHLUUHVSHFWLYHRZQHUV

&RS\ULJKW6(&2/$5086$,QF$OOULJKWVUHVHUYHG7KLVPDWHULDOPD\QRWEHUHSURGXFHGRUFRSLHGLQZKROHRU

LQSDUWZLWKRXWWKHZULWWHQSHUPLVVLRQRI6(&2/$50

SECO-LARM

U.S.A., Inc.

0LOOLNDQ$YHQXH,UYLQH&$ Website: www.seco-larm.com

3,+$.

3KRQH_ (PDLOVDOHV#VHFRODUPFRP

0,B6.)'4BLQGG

'LUHFW$FFHVVWR3URJUDPPLQJ'$3LVXVHGWRHQWHUSURJUDPPLQJPRGHLIWKHPDVWHUFRGHLV

IRUJRWWHQ'$3ZLOOQRWFKDQJHWKHSURJUDPPLQJRIWKHSK-1123-FDQ in any way.

To Use DAP:

1. 'LVFRQQHFWWKHNH\SDG¶VSRZHU

2. Wait one minute to ensure that the keypad’s power is fully discharged.

3. Reconnect the power. The keypad will beep repeatedly for one minute.

4. While the keypad is beeping, press the egress button once to stop the beeping.

NOTE: ,IQRHJUHVVEXWWRQLVLQVWDOOHGWKHQXVHDVPDOOMXPSHUZLUHWRPRPHQWDULO\FRQQHFW

the egress input and common ground terminals.

5. (QWHUWKH'$3FRGH



6. 7KHDPEHU/('ZLOOQRZWXUQ21LQGLFDWLQJWKDWWKHNH\SDGLVUHDG\IRUDQHZPDVWHUFRGHWR

be programmed.

NOTE:

•

6HH³3URJUDPPLQJWKH0DVWHU&RGH´RQSDJHIRUKRZWRSURJUDPDQHZPDVWHUFRGH

•

'LUHFW$FFHVVWR3URJUDPPLQJ'$3ZLOOQRWUHVHWWKHNH\SDG¶VSURJUDPPLQJ,WZLOORQO\HQWHU

programming mode in order to program a new master code

•

For complete system reset, see “System Restore” on page 13.

Direct Access to Programming (DAP):

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Egress Delay/Warning (continued):

•



+ROGFRQWDFWZLWKQRZDUQLQJ±3UHVVDQGKROGWKHHJUHVVEXWWRQIRUWKHSURJUDPPHGGHOD\

time until the door is open. This prevents accidental opening of the door.

•



+ROGFRQWDFWZLWKZDUQLQJEHHS±3UHVVDQGKROGWKHHJUHVVEXWWRQIRUWKHSURJUDPPHG

delay time until the door is open. The keypad will beep during the delay time before letting the

GRRURSHQWRZDUQWKDWVRPHRQHLVSUHSDULQJWRH[LWWKHSURWHFWHGDUHD

NOTE: When the egress button is programmed to hold for a delay time before the door is

released, it is important to put a sign near the egress button to notify users of the

delay time.

Delay Time:

•



±1RGHOD\WLPHGHIDXOW2XWSXWRSHUDWHVLPPHGLDWHO\ZKHQWKHHJUHVVEXWWRQ

is pressed.

•





±(JUHVVEXWWRQGHOD\WLPH7KHGHOD\WLPHFDQEHVHWIURPWRVHFRQGV7KLV

tells the keypad how long to wait after the egress button is pressed before activating output #1.

Examples:

1. Momentary mode ±3UHVVWKHHJUHVVEXWWRQDQGWKHNH\SDGZLOOEHHSIRUVHFRQGVEHIRUH

output #1 activates:



2. +ROGEXWWRQWRDFWLYDWH±3UHVVDQGKROGWKHHJUHVVEXWWRQIRUVHFRQGVDQGWKHNH\SDGZLOO

EHHSIRUWKRVHVHFRQGVEHIRUHRXWSXWDFWLYDWHV



3. Return to default setting ±3UHVVWKHHJUHVVEXWWRQWRDFWLYDWHRXWSXWZLWKQREHHSLQJ

or delay:



NOTE: For safety and to avoid confusion, when a delay or a press-and-hold delay is

SURJUDPPHGSOHDVHSRVWDQRWLFHQHDUWKHHJUHVVEXWWRQVXFKDV³3UHVVDQGKROGWKH

button for 5 seconds or until the door is unlocked.”

CUTOUT

WALL

Installation

screws

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Quick Installation Guide:

Mounting Diagram:

Quick Wiring Diagram:

This page is for installers looking to do a basic installation and programming of the keypad. For

more in-depth installation and programming instructions, see the Table of Contents on page 4.

SK-1123-FDQ

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Quick Programming Guide:

This page is for installers looking to do a basic installation and programming of the keypad.

For more in-depth installation and programming instructions, see the Table of Contents on page 4.

Programming Tips:

• The master, super user, visitor, duress, and user codes cannot be the same.

• $ÀDVKLQJDPEHU/('LQGLFDWHVWKHNH\SDGLVLQVWDQGE\PRGH$VROLGDPEHU/('LQGLFDWHV

the keypad is in programming mode.

• If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of

digits as the master code (see page 24).

Programming Instructions:

Follow the instructions below if the following covers your needs:

• A new master code.

• A single 4-digit user code for all users.

• One output to unlock a door.

• A 3-second delay time in opening the door after the output is activated.

1. Turn off the beeping before the 1-minute power-up period ends:



2. (QWHU3URJUDPPLQJ0RGH:



NOTE:



is the default master code.

3. Change the master code:

[[[[

NOTE:

[[[[

is the new master code.

4. Set the user code to operate output #1 (unlock the door):

[[[[

NOTE:



FKRRVHVXVHU,'RISRVVLEOHXVHUVa

;;;;

LVWKHQHZXVHUFRGHIRUXVHU,'

5. Set the output #1 delay time (skip this step if the default value of 5 seconds

is acceptable):



NOTE:



sets the output #1 delay time for 3 seconds.

6. ([LW3URJUDPPLQJ0RGH



ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Egress Delay/Warning:

With most keypads, the egress button provides a simple way for someone inside a protected

SUHPLVHVWRH[LWWKURXJKDORFNHGGRRUE\SUHVVLQJDEXWWRQLQVWHDGRIXVLQJDNH\SDG+RZHYHU

LQVRPHVLWXDWLRQVGHOD\LQJWKHHJUHVVRSHUDWLRQDQGRUSURYLGLQJVRPHZDUQLQJZKHQWKHHJUHVV

button is used is desirable.

)RUH[DPSOHLQKRVSLWDOVRUVFKRROVLWPD\EHGHVLUDEOHWRGHOD\WKHHJUHVVRSHUDWLRQDQGSURYLGH

a warning to prevent patients or young children from easily leaving the protected area.

For simple egress with no delay or warning, do not change this setting. It is disabled by default.

:KHQSURJUDPPLQJWKHHJUHVVGHOD\ZDUQLQJXVHWKLVJHQHUDOIRUPXOD

DEE



±3URJUDP(JUHVV'HOD\:DUQLQJ

±(JUHVV0RGH

±'HOD\7LPH

Egress Modes:

7KHUHDUHIRXUSRVVLEOHHJUHVVRSHUDWLRQFRQ¿JXUDWLRQVIRUWKHSK-1123-FDQ:

•



0RPHQWDU\FRQWDFWZLWKQRZDUQLQJGHIDXOW±3UHVVWKHHJUHVVEXWWRQPRPHQWDULO\7KH

door opens instantly (default) or after the programmed relay time with no audible warning.

•



0RPHQWDU\FRQWDFWZLWKZDUQLQJEHHS±3UHVVWKHHJUHVVEXWWRQPRPHQWDULO\7KHNH\SDG

will beep for the programmed delay time before letting the door open, to warn that someone is

SUHSDULQJWRH[LWWKHSURWHFWHGDUHD

Programming the Door-Propped-Open Warning and Timing:

If the keypad is connected to an optional magnetic contact or other door protection switch or

device, the keypad can be programmed to beep when a door has been propped open. This

prompts authorized users to close a door that was not closed properly or to investigate a door that

may have been deliberately propped open.

• 'RRUSURSSHGRSHQZDUQLQJ2))GHIDXOW



• 'RRUSURSSHGRSHQZDUQLQJ21

777

NOTE:

•

777

UHSUHVHQWVWKHGHOD\WLPHZKLFKFDQEHVHWIURPWRVHFRQGV

• The delay time provides time for a door to close normally before triggering the door-propped-

open warning.

• The door-propped-open beeping will stop when the open door is closed.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Door-Forced-Open Warning and Timing:

If the keypad is connected to an optional magnetic contact or other door protection switch or

device, the keypad can be programmed to beep when a door has been forced open. The keypad

EHHSFDQEHVHWWRDFWLYDWHIRUWRVHFRQGV

• 'RRUIRUFHGRSHQZDUQLQJ2))GHIDXOW



• 'RRUIRUFHGRSHQZDUQLQJ21

777

NOTE:

•

777

UHSUHVHQWVWKHEHHSDFWLYHWLPHZKLFKFDQEHVHWIURPWRVHFRQGV

• If programmed for door-forced-open warning, the keypad will beep if the door is forced open

without using a user code or the egress button. The keypad will not beep if the door is opened

with a user code or the egress button.

Programming the Amber LED Flashing during Standby Mode:

7KHNH\SDG¶VDPEHU/('W\SLFDOO\ÀDVKHVZKLOHWKHNH\SDGLVLQVWDQGE\PRGHEXWFDQEH

programmed off if needed.

• (QDEOHDPEHU/('ÀDVKLQJGXULQJVWDQGE\PRGHGHIDXOW



• 'LVDEOHDPEHU/('ÀDVKLQJGXULQJVWDQGE\PRGH



Programming the Output Relay Activation Sounds:

The keypad output sounds can be programmed for one of three modes:

• 1REHHSV– The keypad will not beep when the output is activated:



• 1-second beep (default) – The keypad will beep for 1 second when the output is activated:



• 2 short beeps – The keypad will beep twice when the output is activated:



NOTE: This programming function only impacts the output activation sounds. It does not impact

WKHNH\SDGVRXQGVVHH³3URJUDPPLQJWKH.H\SDG6RXQGV´RQSDJH

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Table of Contents:

Quick Installation Guide ..................................................................................................................... 2

0RXQWLQJ'LDJUDP .............................................................................................................................2

4XLFN:LULQJ'LDJUDP ........................................................................................................................2

4XLFN3URJUDPPLQJ*XLGH ................................................................................................................3

Table of Contents ...............................................................................................................................4

Features ............................................................................................................................................ 5

6SHFL¿FDWLRQV .................................................................................................................................... 5

3DUWV/LVW

Overview ............................................................................................................................................ 6

/(',QGLFDWRUVDQG.H\SDG6RXQGV ..................................................................................................6

Installation ......................................................................................................................................... 7

,03257$17127(6 ........................................................................................................................ 7

:LULQJ'LDJUDP .................................................................................................................................. 8

Sample Applications ......................................................................................................................a

Sample Applications for Output #2 .................................................................................................. 

*HWWLQJ5HDG\WR3URJUDP ................................................................................................................ 11

3URJUDPPLQJ)RUPDWDQG'HIDXOW3URJUDPPLQJ9DOXHV .................................................................12

System Restore ...............................................................................................................................13

3URJUDPPLQJWKH0DVWHU&RGH ....................................................................................................... 13

3URJUDPPLQJWKH6XSHU8VHU&RGH ..........................................................................................a

3URJUDPPLQJ8VHU&RGHV ...............................................................................................................16

3URJUDPPLQJ9LVLWRU&RGHVIRU2XWSXW .......................................................................................17

3URJUDPPLQJ'XUHVV&RGHV .....................................................................................................a

3URJUDPPLQJWKH2XWSXW0RGHDQG2XWSXW7LPLQJ ......................................................................... 

3URJUDPPLQJWKH5HDO7LPH&ORFN ................................................................................................. 21

3URJUDPPLQJWKH2XWSXW$XWR'LVDEOH7LPH ........................................................................a

3URJUDPPLQJWKH:URQJ&RGH6\VWHP/RFN8S ............................................................................23

3URJUDPPLQJWKH8VHU&RGH(QWU\0RGH ....................................................................................... 24

3URJUDPPLQJWKH.H\SDG6RXQGV ...................................................................................................24

3URJUDPPLQJWKH2XWSXW5HOD\$FWLYDWLRQ6RXQGV ......................................................................... 25

3URJUDPPLQJWKH$PEHU/(')ODVKLQJGXULQJ6WDQGE\0RGH ........................................................25

3URJUDPPLQJWKH'RRU)RUFHG2SHQ:DUQLQJDQG7LPLQJ .............................................................25

3URJUDPPLQJWKH'RRU3URSSHG2SHQ:DUQLQJDQG7LPLQJ .......................................................... 26

3URJUDPPLQJWKH(JUHVV'HOD\:DUQLQJ .................................................................................. a

'LUHFW$FFHVVWR3URJUDPPLQJ'$3 ............................................................................................. 28

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Features:

6SHFLÀFDWLRQV

Parts List:

Operating voltage a9$&9'&

Current draw

DW9'&

Standby

15mA

Keypress P$

Output 1 active 65mA

Output 1 & 2 active 66mA

7RWDOPD[FXUUHQWGUDZ P$

Outputs

#1 – Form C $#9'&

#2 – Transistor Ground P$#9'&

'XUHVV P$#9'&

Interlock P$#9'&

Tamper P$#9'&

Inputs

(JUHVV 12*URXQG

'RRUVHQVRU 1&*URXQG

'RRULQKLELW 12*URXQG

Operating temperature a)a&

Operating humidity a1RQFRQGHQVLQJ

,35DWLQJ ,3

'LPHQVLRQVLQFOXGLQJEDFNER[

4¾´[⁄´[⁄´[[PP

Weight R]J

• a9$&9'&DXWRDGMXVWLQJRSHUDWLRQ

• 8SWRSRVVLEOHXVHUFRGHVa

SURJUDPPDEOHIRURXWSXWDQGa

for output #2

• 8SWRaSRVVLEOHWHPSRUDU\YLVLWRUFRGHV

which can be programmed for one-time or limited-

WLPHXVHaKRXUV

• 2XWSXW)RUP&UHOD\$#9'&PD[

• 2XWSXW7UDQVLVWRUJURXQGP$#9'&

• Outputs #1 and #2 can be programmed to activate

IRUXSWRVHFRQGVQHDUO\KRXUV

• 7DPSHURXWSXW1&'U\FRQWDFWP$#9'&

PD[

• 0RXQWVWRVWDQGDUGVLQJOHJDQJEDFNER[

• ,3:HDWKHUSURRIUDWLQJ

• Keypad illuminates when a button is pressed;

EDFNOLJKWFDQEHSURJUDPPHGIRU)8//RU$872LQ

standby mode

• All features are programmed directly from the

NH\SDG1RQHHGIRUDQH[WHUQDOSURJUDPPHU

• ((35200HPRU\SURWHFWVSURJUDPPHG

information in case of power loss

• 8SWRaGXUHVVFRGHVIRURXWSXW

aIRURXWSXW

• 'XUHVVFRGHVLJQDOVDVLOHQWDODUPLIDQDXWKRUL]HG

user is forced to open the door under duress

• (JUHVVLQSXWOHWVXVHUVH[LWWKHSUHPLVHVZLWKRXW

keying in the code

• 'RRUVHQVRULQSXWIRUDQWLWDLOJDWLQJRSHUDWLRQ

• Interlocking input for connecting to a second

keypad

• [.H\SDG

• [6HFXULW\VFUHZV

• [6HFXULW\:UHQFK

• ['LRGH

• [0DQXDO

Keypad LEDs off

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Keypad Sounds:

Some of the keypad sounds can be programmed off:

• Keypad audible mode – All the keypad’s status beeps are enabled.

• Keypad silent mode – The successful key entry beep (1 beep) and the unsuccessful user code

HQWU\EHHSVEHHSVDUHGLVDEOHG+RZHYHUWKHZDUQLQJDQGSRZHUXSGHOD\EHHSVUHPDLQ

DFWLYH7KLVSURYLGHVIRUDTXLHWHUZRUNHQYLURQPHQW

To Program:

• To enable keypad audible mode (default):



• To enable keypad silent mode:



NOTE: This programming function only impacts the keypad sounds. It does not impact the output

UHOD\DFWLYDWLRQVRXQGVVHH³3URJUDPPLQJWKH2XWSXW5HOD\$FWLYDWLRQ6RXQGV´

on page 25).

Programming the User Code Entry Mode:

The keypad can be programmed for auto or manual user code entry modes:

• $XWRHQWU\PRGH±3UHVVLQJWKH



NH\LVQRWUHTXLUHGDIWHUW\SLQJLQDXVHUFRGH,QDXWRHQWU\

mode, all user codes must have the same number of digits as the master code.

• Manual entry mode – The



key must be pressed after the user code to indicate the code has

been entered completely. In this case, the user codes can have a different number of digits, from

4 to 8 digits.

To Program:

• For auto entry mode:



• For manual entry mode (default):



NOTE: If the keypad was previously programmed for manual code entry mode and then is

UHSURJUDPPHGIRUDXWRHQWU\PRGHDQ\FRGHVZKRVHOHQJWKH[FHHGVWKHQXPEHURI

GLJLWVRIWKHPDVWHUFRGHZLOOQRORQJHURSHUDWHWKHNH\SDG+RZHYHULIWKHNH\SDGLV

reprogrammed for manual entry mode, the longer codes will again operate the keypad.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

3. In programming mode, clear the auto-disable time:



4. Temporarily pause or resume the auto-disable time:



5. Activate output #1 during the auto-disable time (i.e. open the protected door):



Programming the Output #1 Auto-Disable Time (continued):

Programming the Wrong-Code System Lock-Up:

The keypad can be programmed to lock up in order to secure the premises against unauthorized

entry if multiple wrong codes are entered.

When programming the wrong-code system lock-up, use this general formula:

DD



±3URJUDP:URQJ&RGH6\VWHP/RFN8S

±/RFN2SWLRQV

Lock Options:

Choose from several different options for the wrong-code system lock-up security level:

•



±$IWHUVXFFHVVLYHIDOVHDWWHPSWVXVLQJLQFRUUHFWXVHUFRGHVWKHNH\SDGZLOOORFNIRU

seconds (default).

•



±$IWHUVXFFHVVLYHIDOVHDWWHPSWVXVLQJLQFRUUHFWXVHUFRGHVWKHGXUHVVRXWSXWZLOO

activate. The duress output can be deactivated using any output #1 user code or via the super

user code.

•





±$IWHUWRVXFFHVVLYHIDOVHDWWHPSWVXVLQJLQFRUUHFWXVHUFRGHVWKHNH\SDG

will lock for 15 minutes or until the super user code is used as follows:

SUPER USER CODE



•



±1RV\VWHPORFNXSZLOOKDSSHQ

NOTE 7KHNH\SDG¶VUHG/('ZLOOUHPDLQOLWWRVKRZWKDWWKHNH\SDGLVORFNHG7KHGXUHVVFRGH

will still function in this mode.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

1¾”

(44mm)

2⁄”

(66mm)

⁄”

(15mm)

1⁄”

(46mm)

1¼”

(31mm)

LED Indicators and Keypad Sounds:

Keypad Sounds and Amber LED

Status Sounds

(1)

Amber LED (Center)

In programming mode – 6WHDG\21

Successful key entry 1 Beep 1 Flash

Successful code entry 2 Beeps 2 Flashes

Unsuccessful code entry 5 Beeps 5 Flashes

Power up delay Continuous beeping &RQWLQXRXVÀDVKLQJ

Output relay activation

(2)

1-Sec long beep –

In standby mode

(3)

– )ODVKVHF

System restore mode

2 Beeps )DVWÀDVKLQJIRUPLQ

Code already stored /RQJEHHS –

Real-time clock stopped after

power loss

Continuous 3 fast beeps

every 5 seconds

–

NOTE:

1. .H\SDGVRXQGVFDQEHSURJUDPPHG21RU2))VHHSDJH

2. Output relay activation sounds can be programmed for 1-Sec long beep, 2 short beeps, or OFF

(see page 25).

3. $PEHU/('ÀDVKLQJGXULQJVWDQGE\PRGHFDQEHSURJUDPPHG21RU2))VHHSDJH

LED Indicators

Red LED (Left) Amber LED (Center) Green/Red LED (Right)

Steady Output #2 activated 3URJUDPPLQJPRGH

Output #1 activated (Green)

Output #1 inhibited (Red)

Flashing – Standby mode Inhibit mode paused (Red)

Overview:

3⁄”

PP

4¾”

PP

CUTOUT

WALL

Installation

screws

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Installation:

IMPORTANT NOTES:

1. Find a suitable location to mount the keypad. Install it at the height at which most users will be

able to easily operate the keypad.

2. 7KHNH\SDGFDQEHLQVWDOOHGLQDVLQJOHJDQJEDFNER[RUFDQEHÀXVKPRXQWHGGLUHFWO\WR

the wall.

• ,IÀXVKPRXQWLQJWKHNH\SDGFXWRXWD



´[



´[



´[[PPKROHWR¿WWKHEDFN

SRUWLRQRIWKHNH\SDG/HDYHURRPIRUWKHNH\SDGZLULQJDQGZLULQJKROH

3. Run the wire through the wall or conduit to the keypad location, then run the wire through the

hole on the back of the keypad.

4. 5HIHUWRWKHZLULQJGLDJUDPSDJHDQGHQVXUHWKDWWKHEDFNOLWMXPSHULVSURSHUO\VHW

5. Connect the wires to the keypad according to the wiring diagram on page 8.

6. )LQLVKDVVHPEO\E\DWWDFKLQJWKHNH\SDGWRWKHVLQJOHJDQJEDFNER[ZLWKWKHLQFOXGHGVHFXULW\

VFUHZVRUE\ÀXVKPRXQWLQJWKHNH\SDGLQWKHDOUHDG\FXWKROHLQWKHZDOO

1. $OZD\VGLVFRQQHFWSRZHUEHIRUHVHUYLFLQJWKHNH\SDG'RQRWDSSO\SRZHUXQWLODOOFRQQHFWLRQ

wiring is completed.

2. 7KHNH\SDGPXVWEHSURSHUO\JURXQGHG8VHDPLQLPXPRI$:*ZLUHFRQQHFWHGWRWKH

ground terminal. Failure to do so may damage the keypad.

3. All wiring and programming should be done by a professional installer to reduce the risk of

improper installation.

IF USING THE KEYPAD WITH A MECHANICALLY

OPERATED DOOR OR GATE, MOUNT THE KEYPAD AT

LEAST 15’ (5m) FROM THE DOOR OR GATE TO PREVENT

USERS FROM BEING CRUSHED OR PINNED. FAILURE TO

DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

The keypad can be programmed so that output #1 is disabled for a certain period of time every day.

Output #1 will be disabled at the start time, and will be re-enabled at the end time. This ensures

that users are not allowed into the protected premises, such as during lunch hour or at night.

NOTE:

• The real-time clock must be operating in order to set the output #1 auto-disable time

VHH³3URJUDPPLQJWKH5HDO7LPH&ORFN´RQSDJH

• For safety purposes, the egress button still works while output #1 is auto-disabled.

• 7KHWLPHLVVHWXVLQJWKHPLOLWDU\KRXUWLPHIRUPDWWR

• If the programmed start time is before the end time, output #1 is auto-disabled within a single

day. If the programmed start time is after the end time, the end time will be on the

following day.

• The start time and end time cannot be the same.

• The output #1 auto-disable time can be temporarily paused and restarted using the super user

FRGHVHH³3URJUDPPLQJWKH6XSHU8VHU&RGH´RQSDJHVa

• 'XULQJWKHRXWSXWDXWRGLVDEOHWLPHWKHVXSHUXVHUFRGHFDQEHXVHGWRRSHUDWHRXWSXW

• 7KHUHG/('ZLOOUHPDLQOLWGXULQJWKHRXWSXWDXWRGLVDEOHWLPH

When programming the auto-disable time, use this general formula:

++00++00



±3URJUDP2XWSXW$XWR'LVDEOH7LPH

++00

– Start Time

++00

±(QG7LPH

Start Time:

• Start time for the output #1 auto-disable time.

represents hours and

represents

PLQXWHVLQWKHPLOLWDU\KRXUWLPHIRUPDWIURPWR

End Time:

• (QGWLPHIRURXWSXWDXWRGLVDEOHWLPH

represents hours and

represents

PLQXWHVLQWKHPLOLWDU\KRXUWLPHIRUPDWIURPWR

Examples LQWKHVHH[DPSOHVDVVXPHWKDWWKHVXSHUXVHUFRGHLV



1. ,QSURJUDPPLQJPRGHVHWWKHDXWRGLVDEOHWLPHIURP30WR30



2. ,QSURJUDPPLQJPRGHVHWWKHDXWRGLVDEOHWLPHIURP30WR$0WKHIROORZLQJGD\



Programming the Output #1 Auto-Disable Time:

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Real-Time Clock:

A 24-hour real-time clock provides the baseline time needed to start and stop the output #1 auto-

GLVDEOHWLPHVHH³3URJUDPPLQJWKH2XWSXW$XWR'LVDEOH7LPH´RQSDJHV

If the output #1 auto-disable time is not programmed, it is not necessary to set the real-time clock.

To set the clock, use this general formula:

++00



±3URJUDP5HDO7LPH&ORFN

++±+RXUV

00 – Minutes

Setting Hours and Minutes:

•

represents hours and

represents minutes in the military (24-hour) time format,

IURPWR

Examples:

1. 6HWWKHUHDOWLPHFORFNWR$0



2. 6HWWKHUHDOWLPHFORFNWR30



NOTE:

• If the output #1 auto-disable time is programmed, losing power will cause the keypad to beep 3

times every 5 seconds. To deactivate this alert, either reset the real-time clock or clear the output

#1 auto-disable time.

• If the output #1 auto-disable time is not programmed, losing power will not cause the keypad to beep.

• 7RHQVXUHDFFXUDWHWLPHLWLVDGYLVHGWRUHSURJUDPWKHUHDOWLPHFORFNHYHU\WKUHHWRVL[PRQWKVDQG

ZKHQ'D\OLJKW6DYLQJV7LPHEHJLQVDQGHQGVLIDSSOLFDEOH

TAMPER

N.C.

O/P 2

N.O.

OUT

(–)

GND

DOOR

SENS.

O/P 1

INHIB

INT

LOCK

(+) (–)

12~24 VAC/DC

OUTPUT 1

N.C. | COM | N.O.

FULL AUTO

BACK-LIT

BUZZER

Connection terminals

Backlit jumper

Connection terminals

Stand-Alone Door Lock:

In this application, the keypad is connected to a single door lock and an egress pushbutton.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Connection Terminals

7DPSHU1&

7DPSHUVZLWFKRXWSXW1&FRQWDFW

PD[P$#9'&

&RQQHFWWRWKH1&KRXUSURWHFWLRQ]RQHRI

an alarm if needed.

a9$&9'&

&RQQHFWWRDa9$&9'&SRZHUVXSSO\

Observe polarity.

2XWSXW1&

121&&20UHOD\RXWSXW

PD[$#9'&

Output 1 COM

2XWSXW12

2XWSXW12 7UDQVLVWRUJURXQGRXWSXWPD[P$#9'&

'XUHVV2XWSXW

7UDQVLVWRUJURXQGRXWSXWPD[P$#9'&

Triggers a silent alarm or other device when the

user enters a duress code.

(JUHVV,QSXW 123XVKEXWWRQFRQWDFWWRJURXQG3UHVVEXWWRQWRDFWLYDWH2XWSXW

Ground (-) Common ground output.

'RRU6HQVRU

&RQQHFWWRDQRSWLRQDO1&VHQVRUVXFKDVDPDJQHWLFFRQWDFWWRPRQLWRULIDGRRULVRSHQRU

closed. Connect to ground (–) if not used.

Output 1 Inhibit

2XWSXWLQKLELWRU12LQSXWFRQQHFWWR,QWHUORFN&RQWURORIVHFRQGNH\SDGLIQHHGHGVRWKDWLI

one keypad is used to open a door, the other is temporarily disabled.

Interlock Control

,QWHUORFN&RQWURO12LQSXWFRQQHFWWR2XWSXW,QKLELWRIVHFRQGNH\SDGLIQHHGHGVRWKDWLIRQH

keypad is used to open a door, the other is temporarily disabled.

Wiring Diagram:

Jumper Settings

Jumper Position Description

Backlit

Full 'LPEDFNOLWGXULQJVWDQGE\)XOOEDFNOLWIRUVHFRQGVDIWHUDQ\EXWWRQSUHVV

Auto 1REDFNOLWGXULQJVWDQGE\)XOOEDFNOLWIRUVHFRQGVDIWHUDQ\EXWWRQSUHVV

Sample Applications:

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Sample Applications (continued):

Inter-Lock System Using Two Keypads:

In this application, two keypads are each connected to separate door locks and egress

pushbuttons. While one door is open, the other cannot be opened.

• 8VHDQ1&PDJQHWLFFRQWDFWRUVRPHRWKHU1&GHYLFHWRGHWHFWZKHWKHUDGRRULVRSHQHGRU

FORVHG'RWKLVIRUWKHWZRGRRUVEHLQJSURWHFWHG

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Output Mode and Output Timing:

7KHUHOD\IRURXWSXWVDQGFDQEHSURJUDPPHGWRWULJJHU21DQG2))ZLWKDXVHUFRGH

(toggle mode), or to trigger for a programmed length of time of up to nearly 28 hours before

automatically turning OFF. The toggle or timed outputs can be used for locking or unlocking a door

or for a variety of functions that can be controlled with the keypad.

When programming the output mode and time, use this general formula:

$$%%%%%

– Output

– Output Mode and Time

Outputs:

•



– Output #1

•



– Output #2

Output Mode and Time:

•



±6WDUWVWRSWRJJOHPRGH,QWKLVFDVHWKHRXWSXWVWDUWVZKHQDXVHUFRGHLVHQWHUHGDQG

stops when a user code is entered.

•





±7KHRXWSXWWULJJHUHGE\DXVHUFRGHODVWVWRVHFRQGVQHDUO\

28 hours) before automatically turning off (default 5 seconds).

NOTE: While the keypad is in momentary timed output mode, the output can be reset any time

by entering the super user code.

Examples:

,QWKHVHH[DPSOHVDVVXPHWKDWWKHVXSHUXVHUFRGHLV



1. In programming mode, set output #1 to toggle:



2. ,QSURJUDPPLQJPRGHVHWRXWSXWWRVHFRQGV



3. Reset output #1 timer:



4. Reset output #2 timer.



ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming Duress Codes (continued):

2. 6HWWKHGXUHVV,'FRGHIRURXWSXWWR



3. 'HOHWHWKHGXUHVV,'FRGHIRURXWSXWIURPPHPRU\



4. 'HOHWHDOOGXUHVVFRGHVIRURXWSXWIURPPHPRU\



Operating Duress Codes:

If a duress code is used in place of a normal user code, both the appropriate outputs #1 or #2 and

WKHGXUHVVRXWSXWZLOOEHDFWLYDWHG+RZHYHUDGXUHVVFRGHcannot deactivate the duress output.

Only a normal user code, super user code, or a master code can deactivate the duress output.

Examples:

,QWKHVHH[DPSOHVDVVXPHWKDW



is an output #1 duress code and that



is a user code.

1. Activate the duress output and output #1 using the duress code:



NOTE6XEVHTXHQWO\HQWHULQJWKHGXUHVVFRGHZLOODFWLYDWHRXWSXWDJDLQEXWZLOOQRW

deactivate the duress output.

2. 'HDFWLYDWHWKHGXUHVVRXWSXWXVLQJWKHXVHUFRGH



+12VDC

O/P 2

N.O.

OUT

(-)

GND

IN4004

N.C.

COM

N.O.

O/P 2

N.O.

OUT

(-)

GND

DOOR

SENS

O/P 1

INHIB

INT.

LOCK

WARNING

• Make sure nobody is inside

the house before starting

the door lock inhibit

function.

• The inhibit authorization

code should always be

kept by only the owner.

N.C.

OUTPUT #1

COM

N.O.

O/P 2

N.O.

Electric Lock

IN4004

N.C.N.O.

12VDC

Power Supply

N.C.

COM

N.C.

OUTPUT #1

COM

N.O.

O/P 2

N.O.

Electric Lock

N.O.

IN4004

12VDC

Power

Supply

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

1. Drive an Optional Output Relay

2. Connecting Inhibit Control

• 8VHD9'&UHOD\DQGFRQQHFWLWWRWKHVDPH

12V power supply as the keypad.

• 8VLQJWKLVVHWXSWKHRZQHUPD\HQWHUWKHXVHU

code for output #2 to disable output #1 during a

certain period to prevent unauthorized access.

• 6HWRXWSXWWRVWDUWVWRSWRJJOHPRGHVHH

SDJH

• Connect the output 1 inhibit terminal with the

RXWSXW12WHUPLQDODVVKRZQLQZLULQJ

diagram.

• 2XWSXWLVLQYDOLGZKLOHWKH23,1+,%

terminal is shunted to ground via output #2.

3. For Door-Hold-Open Mode

• )RU1&ORFNLQJGHYLFHV&RQQHFWDUHOD\

to output #2 in series with the locking device.

• )RU12ORFNLQJGHYLFHV&RQQHFWDUHOD\WR

output #2 in parallel with the locking device.

Sample Applications for Output #2:

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Getting Ready to Program:

Keypad Codes:

7KHUHDUH¿YHW\SHVRINH\SDGFRGHV

• 0DVWHUFRGH±8VHGRQO\IRUHQWHULQJSURJUDPPLQJPRGHWKHUHFDQEHRQO\RQHPDVWHUFRGH

per keypad.

• Super user code – Can be used to activate outputs #1 and #2, or to disable (inhibit) or enable

the operation of output #1.

• 8VHUFRGHV±8QLTXHFRGHVIRUHDFKXVHUWRDFWLYDWHRXWSXWVRU

• Visitor codes – Temporary user codes that can be assigned to visitors or temporary workers to

DFWLYDWHRXWSXWWKHYLVLWRUFRGHVFDQEHSURJUDPPHGIRURQHWLPHXVHRUWRH[SLUHDIWHUDVHW

number of hours has passed.

• 'XUHVVFRGHV$VVLJQHGWRVSHFL¿FXVHUVDVDZD\WRVHQGDVLOHQWDOHUWLIIRUFHGWRXVHNH\SDG

under duress.

Power Up the Keypad:

:KHQWKHNH\SDGLV¿UVWSRZHUHGXSLWZLOOEHHSFRQWLQXRXVO\IRUDERXWPLQXWH'XULQJWKLV

SRZHUXSWLPHLIQHHGHGXVH'LUHFW$FFHVVWR3URJUDPPLQJ'$3WRUHVHWWKHPDVWHUFRGHVHH

³'LUHFW$FFHVVWR3URJUDPPLQJ'$3´RQSDJH

1. Turn off the beeping before the 1-minute power-up period ends:



This will immediately stop the beeping.

When the beeping has ended, the keypad is ready for normal operation or for programming.

Enter and Exit Programming Mode:

All programming of the keypad is done in programming mode.

1. (QWHUSURJUDPPLQJPRGH

[[[[

NOTE:

;;;;

is the master code.



is the default master code

VHH³3URJUDPPLQJWKH0DVWHU&RGH´RQSDJHWRSURJUDPDQHZPDVWHUFRGH

7KHDPEHU/('ZLOOWXUQWRDVWHDG\21WRLQGLFDWHWKDWWKHNH\SDGLVLQSURJUDPPLQJ

mode.

2. ([LWSURJUDPPLQJPRGH



The



HQWU\FDQEHXVHGWRH[LWSURJUDPPLQJPRGHDWDQ\WLPHZKLOHSURJUDPPLQJ7KH

DPEHU/('ZLOOUHWXUQWRÀDVKLQJLQGLFDWLQJVWDQGE\PRGHXSRQH[LWLQJSURJUDPPLQJPRGH

NOTE: DO NOT DISCONNECT THE KEYPAD FROM POWER WHILE IN

PROGRAMMING MODE'LVFRQQHFWLQJWKHNH\SDGZKLOHLQSURJUDPPLQJPRGH

could cause a keypad memory error.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming Duress Codes:

'XUHVVFRGHVDOORZXVHUVWRWULJJHUDVLOHQWDODUPRUDOHUWLIWKH\DUHIRUFHGWRDOORZDFFHVVWRD

protected area. If a user uses a duress code instead of his or her normal user code, outputs #1 or

#2 will activate as normal, but the duress output will simultaneously activate to trigger a silent alarm

or alert.

NOTE:

• 'XUHVVFRGHVDUHDOZD\VYDOLGDQGDUHQRWLQKLELWHGE\DQ\RWKHURSHUDWLRQRIWKHNH\SDG

• 'XUHVVFRGHVFDQQRWEHWKHVDPHDVDQ\RWKHUFRGHV

• The duress code should be easy to remember. For instance, it can be the same as a user’s

QRUPDOXVHUFRGHEXWZLWKDVLQJOHGLJLWFKDQJHGDVE\VXEWUDFWLQJRUDGGLQJWRWKH¿UVWRUODVW

GLJLWRIWKHFRGH)RUH[DPSOHLIWKHXVHUFRGHLVDJRRGGXUHVVFRGHPLJKWEH

When programming duress codes, use this general formula:

$$%%&&&&

– Output

±'XUHVV,'

±'XUHVV&RGH

Outputs:

•



– Output #1

•



– Output #2

Duress IDs:

•





±8SWRGXUHVVFRGHVFDQEHSURJUDPPHGIRURXWSXW

•





±8SWRGXUHVVFRGHVFDQEHSURJUDPPHGIRURXWSXW

•



±'HOHWHDOOFXUUHQWO\SURJUDPPHGGXUHVVFRGHVIRUWKHVHOHFWHGRXWSXW

Duress Codes:

• A duress code can be 4 to 8 digits long and must have the same length as all other codes if the

NH\SDGLVXVHGLQDXWRFRGHHQWU\PRGHVHH³3URJUDPPLQJWKH8VHU&RGH(QWU\0RGH´RQ

page 24)

Examples:

1. 6HWWKHGXUHVV,'FRGHIRURXWSXWWR



ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming Visitor Codes for Output #1:

9LVLWRUFRGHVDUHWHPSRUDU\FRGHVWKDWH[SLUHDIWHUXVHRUDIWHUDVSHFL¿HGDPRXQWRIWLPHKDV

elapsed. While active, they operate output #1 as normal user codes.

NOTE:

• 9LVLWRUFRGHVFDQQRWEHXVHGWRGHDFWLYDWHWKHGXUHVVRXWSXWVHH³2SHUDWLQJ'XUHVV&RGHV´RQ

SDJH

• If the keypad is powered down, any programmed visitor codes will be deleted.

When programming visitor codes, use this general formula:

DDEEFFFF



±3URJUDP9LVLWRU&RGHV

D±9LVLWRU,'

E±9DOLG'XUDWLRQKRXUV

F – Visitor Code

Visitor IDs:

•





±XQLTXHYLVLWRU,'VIRUYLVLWRUFRGHVIRURXWSXW

•



±'HOHWHDOOFXUUHQWO\SURJUDPPHGYLVLWRUFRGHV

Valid Duration:

•



– Set a one-time code. This code can only be used once by a visitor, after which it is

automatically deleted.

•





±6HWWKHGXUDWLRQWKHYLVLWRUFRGHZLOOEHYDOLGIURPWRKRXUV

Visitor Codes:

• A visitor code can be 4 to 8 digits long, and must have the same length as all other codes if the

NH\SDGLVXVHGLQDXWRFRGHHQWU\PRGHVHH³3URJUDPPLQJWKH8VHU&RGH(QWU\0RGH´RQ

page 24).

Examples:

1. 6HWWKHYLVLWRU,'FRGHWRDQGPDNHLWDRQHWLPHFRGH



2. 6HWWKHYLVLWRU,'FRGHWRDQGPDNHLWYDOLGIRUWKUHHKRXUV



3. 'HOHWHWKHYLVLWRU,'FRGHIURPPHPRU\ 



4. 'HOHWHDOOFXUUHQWO\SURJUDPPHGYLVLWRUFRGHV



ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming Format and Default Programming Values:

In this manual, the format used for programming the keypad is as follows:

• A 2-digit (

;;

)81&7,21LGHQWL¿HUWRWHOOWKHNH\SDGZKDWLVEHLQJSURJUDPPHG

• A varying number of digits (

;

WRUHSUHVHQWWKHSDUDPHWHUVRIWKDW)81&7,21

• The



NH\WRFRQ¿UPSURJUDPPLQJRIWKH)81&7,21

The following is a list of the different programming functions:

Function Parameters Default functions and values Page #

 Master code 'HIDXOWFRGHOHQJWKIURPaGLJLWV 13

 Super user code 1RGHIDXOWPXVWEHSURJUDPPHG a

 8VHUFRGHVIRURXWSXW 1RGHIDXOWPXVWEHSURJUDPPHG 16

 8VHUFRGHVIRURXWSXW 1RGHIDXOWPXVWEHSURJUDPPHG 16

 Visitor codes for output #1 1RGHIDXOWPXVWEHSURJUDPPHG 17

41 'XUHVVFRGHVIRURXWSXW 1RGHIDXOWPXVWEHSURJUDPPHG a

42 'XUHVVFRGHVIRURXWSXW 1RGHIDXOWPXVWEHSURJUDPPHG a

51 Output mode for output #1 5-Second output, momentary 

52 Output mode for output #2 5-Second output, momentary 

55 System real-time clock 1RGHIDXOWPXVWEHSURJUDPPHG 21

56 Auto-disable time 1RGHIDXOWPXVWEHSURJUDPPHG a

 Wrong-code system lock-up /RFNVNH\SDGDIWHUIDOVHFRGHFDUGWULHV 23

 8VHUFRGHHQWU\PRGH Manual entry of “#” after each code 24

71 Keypad sounds 3URJUDPPLQJDQGRSHUDWLRQEHHSVHQDEOHG 24

72 Output relay activation sounds 1-Second beep when output is activated 25

73 $PEHU/('VWDQGE\ÀDVKLQJ &HQWHU/('ÀDVKHVRQVWDQGE\ 25

 'RRUIRUFHGRSHQZDUQLQJ Warning disabled 25

81 'RRUSURSSHGRSHQZDUQLQJ Warning disabled 26

 (JUHVVGHOD\ZDUQLQJ (JUHVVRXWSXWKDSSHQVLPPHGLDWHO\ a

NOTE7KH'LUHFW$FFHVVWR3URJUDPPLQJ'$3FRGHSDJHDQGWKHV\VWHPUHVWRUH

FRGHSDJHDUH¿[HGDQGFDQQRWEHFKDQJHGHYHQYLDSURJUDPPLQJ

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

System Restore:

6\VWHPUHVWRUHZLOOUHVHWDOOSURJUDPPLQJYDOXHVH[FHSWWKHPDVWHUFRGHEDFNWRWKHGHIDXOWYDOXHV

shown on page 12.

1. 0DNHVXUHWKHNH\SDGLVLQSURJUDPPLQJPRGHVHH³(QWHUDQG([LW3URJUDPPLQJ0RGH´RQ

page 11).

2. Initiate system restore:



NOTE:

• 6\VWHPUHVWRUHZLOOUHVHW$//SURJUDPPLQJH[FHSWWKHPDVWHUFRGHEDFNWRGHIDXOWYDOXHV%H

careful to use system restore only when absolutely necessary.

• 6\VWHPUHVWRUHPD\WDNHVHYHUDOPLQXWHV7KHDPEHU/('ZLOOÀDVKUDSLGO\GXULQJWKLVWLPH

• Once system restore has been completed, the keypad will beep twice to show that all

programming values have been reset to their default values and are ready to be

re-programmed.

• At this point, the keypad is still in programming mode.

Programming the Master Code:

The master code is used to enter programming mode. The master code does not serve as a user

code for activating outputs #1 or #2.

1. 0DNHVXUHWKHNH\SDGLVLQSURJUDPPLQJPRGHVHH³(QWHUDQG([LW3URJUDPPLQJ0RGH´RQ

page 11).

2. (QWHUQHZPDVWHUFRGH

[[[[

NOTE:

•

;;;;

represents the new master code, which can be 4 to 8 digits long.

• There can be only one master code for the keypad.

• 3URJUDPPLQJDQHZPDVWHUFRGHZLOORYHUZULWHWKHSUHYLRXVPDVWHUFRGH

• ,IWKHPDVWHUFRGHLVIRUJRWWHQXVH'LUHFW$FFHVVWR3URJUDPPLQJ'$3WRUHVHWWKHPDVWHU

code (see page 28).

• The master, super user, visitor, duress and user codes cannot be the same.

• If the keypad is set for Auto Code Entry Mode, all codes will need to be the same number of

digits as the master codeVHH³3URJUDPPLQJWKH8VHU&RGH(QWU\0RGH´RQSDJH

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming User Codes:

When programming user codes, use this general formula:

$$%&&&''''

– Output

– Add or delete a user code

±8VHU,'

±8VHU&RGH

Outputs:

•



±2XWSXWXSWRSRVVLEOHXVHUFRGHV

•



±2XWSXWXSWRSRVVLEOHXVHUFRGHV

Code Addition / Deletion:

•



– Add a user code

•



±'HOHWHDSURJUDPPHGXVHUFRGH

•



±'HOHWHDOOSURJUDPPHGXVHUFRGHVIRUWKHVHOHFWHGRXWSXW

User IDs:

•





±XQLTXHXVHU,'VIRUXVHUFRGHVIRURXWSXW

•





±XQLTXHXVHU,'VIRUXVHUFRGHVIRURXWSXW

User Codes:

• A user code can be 4 to 8 digits long, and must have the same length as all other codes if the

NH\SDGLVXVHGLQDXWRFRGHHQWU\PRGHVHH³3URJUDPPLQJWKH8VHU&RGH(QWU\0RGH´RQ

SDJHVa

• The master, super user, visitor, duress, and user codes cannot be the same.

Examples:

1. 3URJUDPXVHUFRGH



IRUXVHU,'IRURXWSXW



2. 'HOHWHFRGHIRUXVHU,'IRURXWSXW



3. 'HOHWHDOOXVHUVIRURXWSXW



ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Super User Code (continued):

3. 7RJJOHRSHUDWLRQRIRXWSXW21RU2))



NOTE:

• 7KLVIXQFWLRQLVXVHGWROHDYHRXWSXWDFWLYHIRUH[WHQGHGSHULRGVRIWLPH

• :KLOHRXWSXWUHPDLQVDFWLYHWKHJUHHQ/('UHPDLQVOLW

• 'RQRWIRUJHWWRGHDFWLYDWHWKLVIXQFWLRQDIWHULWVXVHLVQRORQJHUUHTXLUHG

• It is recommended to only use this function with fail-safe locks.

• $OOIXQFWLRQVUHTXLULQJXVHRIWKHGRRUVHQVRULQSXWDUHVXVSHQGHGZKLOHWKLVIXQFWLRQ

is in use.

4. Temporarily pause or restart the timed output #1 auto-disable period:



NOTE:

• This function is used to enable the operation of output #1 if it was disabled using the auto-

GLVDEOHIXQFWLRQVHHSDJHVa

• :KHQWKHRXWSXWDXWRGLVDEOHIXQFWLRQLVLQDFWLYHWKHUHG/('ZLOOÀDVKVWHDGLO\7KLV

indicates that output #1 may now be used.

5. 'LVDEOHRUHQDEOHRXWSXWWRJJOHUHJDUGOHVVRISURJUDPPLQJ



NOTE:

• This is used to prevent users from accessing the protected premises.

• )RUPRUHLQIRUPDWLRQRQSURJUDPPLQJWLPHGRUWRJJOHPRGHVHH³3URJUDPPLQJWKH2XWSXW

0RGHDQG2XWSXW7LPLQJ´RQSDJH

• 7KHUHG/('ZLOOUHPDLQVWHDG\RQZKLOHRXWSXWLVGLVDEOHG

• For safety reasons, the egress button works regardless of whether output #1 is enabled or

disabled via the super user code.

• The super user code continues to operate output #1 even while that output is disabled.

ENFORCER Vandal Resistant Flush-Mount Access Control Keypad

SECO-LARM U.S.A., Inc.

Programming the Super User Code:

The super user code has multiple functions:

• The super user code can activate or deactivate output #1 and #2 at any time.

• The super user code can toggle operation of output #1 on or off.

• The super user code can pause or restart the timed output #1 auto-disable period.

• The super user code can enable or disable output #1.

• 7KHVXSHUXVHUFRGHLVH[HPSWIURPDQ\V\VWHPLQKLELWLRQRUORFNXSIXQFWLRQV,WLVYDOLGDWDQ\

time.

Programming the Super User Code:

1. 0DNHVXUHWKHNH\SDGLVLQSURJUDPPLQJPRGHVHH³(QWHUDQG([LW3URJUDPPLQJ0RGH´RQ

page 11).

2. (QWHUWKHQHZVXSHUXVHUFRGH

[[[[

NOTE:

•

;;;;

represents the new super user code, which can be 4 to 8 digits long.

• There can be only one super user code for the keypad.

• 3URJUDPPLQJDQHZVXSHUXVHUFRGHZLOORYHUZULWHWKHSUHYLRXVVXSHUXVHUFRGH

• The master, super user, visitor, duress, and user codes cannot be the same.

Deleting the Super User Code:

This function is useful for protecting the premises in case the super user code is forgotten.

To delete a super user code:

1. Make sure the keypad is in programming mode (see page 11).

2. (QWHU



Using the Super User Code:

,QWKHVHH[DPSOHVDVVXPHWKHVXSHUXVHUFRGHLV



1. Activate or deactivate output #1 (timed or toggle, depending on programming):



2. Activate or deactivate output #2 (timed or toggle, depending on programming):



ENFORCER SK-1123-FDQ Installation guide

Brand: ENFORCER

Model: SK-1123-FDQ

Type: Installation guide

Download PDF

report

ENFORCER SK-1123-FDQ Installation guide

ENFORCER SK-1123-FDQ Installation guide

Related papers

Other documents