Instruction Manual
Model 2000-318
2000-324
SSPB Power Supply
November 2009 Rev 0
POWER
CROSS TECHNOLOGIES, INC.
2000 POWER SUPPLY
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
INSTRUCTION MANUAL
MODEL 2000-318/324 SSPB Power Supply
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Rear Panel Inputs & Outputs 6
2.3 Front Panel Indicators 6
2.4 Operation 7
2.5 Use Information 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies,
Inc.’s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies,
Inc. shall not be liable for any special, indirect, or consequential damages. This warranty
does not cover parts or equipment which have been subject to misuse, negligence, or
accident by the customer during use. All shipping costs for warranty repairs will be
prepaid by the customer. There are not other warranties, express or implied, except as
stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2000-318/324 Manual_Rev 0 Page 2 11/23/09
MODEL 2000-318/324 SSPB Power Supply
1.0 General
1.1 Equipment Description
The 2000-318/324 SSPB Power Supply is a switching power supply which provides regulated +18 VDC (-318)
OR +24 VDC (-324) at 2.5 amps through RF connectors for insertion on an RF line. Also provided is a BNC
connector for insertion of a 10 MHz reference signal on the RF line. The input AC connector is IEC 320 C13.
The 2000-318/324 can be mounted on an optional 1 3/4” X 19” rack mount panel (option -R).
POWER
CROSS TECHNOLOGIES, INC.
2000 POWER SUPPLY
FRONT PANEL
REF IN
RF
RF+DC
J1 J3J2
F1
FUSE
DS1
DC
ON
RF
CAUTION! RISK OF
ELECTRIC SHOCK
DO NOT OPEN!!!
100-240 ±10%VAC
47-63 HZ
FUSE 2A
REAR PANEL
FIGURE 1.1 Front and Rear Panels
RF
LNB
+24 VDC
EXT 10MHz
fuse
RF+DC
SURGE
SUPPRESOR
FIGURE 1.2 Block Diagram
2000-318/324 Manual_Rev 0 Page 3 11/23/09
1.2 Technical Characteristics
TABLE 1.0 2000-318/324 SSPB Power Supply Specifications*
RF Input/Output Characteristics
Impedance/Return Loss 75/14 dB
Frequency 950 - 2150 MHz
Insertion Loss 1 ± 0.5 dB
Frequency Response ±1.0 dB
AC Input Characteristics
Voltage 100-240 ±10% VAC
Frequency 47 - 63 Hz
Power, maximum 65 watts
DC Output Characteristics
Voltage / Current +18 VDC/ 2.5 amps (Model 2000-318)
+24 VDC/ 2.5 amps (Model 2000-324)
Load Regulation, max. ± 5%
Power Supply type Switcher
Switching Frequency 50 kHz, typical
Indicators
DC Power (front) Green LED
DC Power Insertion (rear) Yellow LED
Other
AC Input Connector IEC 320 C13
RF Connectors Type F (female)
10MHz REF Connector BNC (female), 50/75
Size, Bench Top 4.7” wide X 1.75” high X 8.5” deep
Size, Rack Mount 19 inch standard chassis 1.75”high X 9.0” deep (option R)
Options
R, R2, R3 Rack Mount Panel (1, 2, or 3 position)
B75 BNC (RF)
D50 BNC (RF)
*+10˚C to +40˚C; Specifications subject to change without notice
2000-318/324 Manual_Rev 0 Page 4 11/23/09
2.0 Installation
2.1 Mechanical
The 2000-318/324 is packaged in an aluminum extrusion. The -R option is mounted on a 1 3/4” X 19” panel
that can be mounted to a rack using the 4 holes at the ends.
EXTRUSION
FRONT SCREWS (4EA)
FRONT PANEL
RACK MOUNT PANEL (FOR -R MODELS ONLY)
REAR SCREWS (4EA)
PCB
ASSEMBLY
REAR PANEL
POWER
SUPPLY
CABLE
2000 POWER SUPPLY
CROSS TECHNOLOGIES, INC.
DC
FIGURE 2.1 Mechanical Assembly (Rack Mounting)
2000-318/324 Manual_Rev 0 Page 5 11/23/09
2.2 Rear Panel Input/Output Signals - Figure 2.2 shows the input and output connectors on the rear panel.
REF IN
RF
RF+DC
J1 J3J2
F1
FUSE
DS1
DC
ON
RF
CAUTION! RISK OF
ELECTRIC SHOCK
DO NOT OPEN!!!
100-240 ±10%VAC
47-63 HZ
FUSE 2A
J1 - RF + DC
The looped signal from J2 containing
the inserted +18VDC/+24VDC and/or
10MHz referernce
J3 - REF IN
Connect the external 10 MHz
reference signal to be inserted
at RF+DC here.
F1 - FUSE
When the provided fuse is inserted,
+18VDC/+24VDC, 2.5 amps max
will be present at RF+DC
DS1 - DC ON RF
Lights yellow when
+18VDC/+24VDC is present
at RF+DC.
J2 - RF
The RF signal upon which you wish to
insert the +18VDC/+24VDC and/or the
10MHz reference
FIGURE 2.2 Rear Panel I/Os
TABLE 2.1 Coonnector
Connector Options
Option RF
STD Type F, 75
-B BNC, 75
-D BNC, 50
2.3 Front Panel Indicators - The following are the front panel indicators.
DS2 - POWER LED
Lights green when DC
power is present
POWER
CROSS TECHNOLOGIES, INC.
2000 POWER SUPPLY
FIGURE 2.3 Front Panel Indicators
2000-318/324 Manual_Rev 0 Page 6 11/23/09
2.4 Operation
2.4.1 Installing and Operating the 2000-318/324 SSPB Power Supply
1. Connect an RF signal to RF connector, J2 (Figure 2.2).
2. Connect RF+DC connector, J1, to the external equipment (Figure 2.2).
3. To insert +18 VDC/+24 VDC on the RF signal insert a 1 amp fuse (provided) in fuse holder,
F1 (Figure 2.2).
4. To insert a 10MHz reference signal on the RF signal connect a 10MHz source to the REF IN, J3
(Figure 2.2).
5. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC on the back panel (Figure 2.2).
6. Be sure DS2 (green, DC Power) is on (Figure 2.3).
7. If fuse, F1, is inserted check that SSPB Power LED, DS1, is on (Figure 2.2)
8. AC FUSE - The AC fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot
in the drawer below the AC input as shown in Figure 2.4. There is a spare fuse in the near slot. If a fuse
continues to open, the power supply is most likely defective.
FUSE DRAWER
SPARE FUSE DRAWER
AC Fuse - 2 amp slow blow (Type T 2A GDC),
5 mm X 20 mm
~
INPUT
100-240± 10%VAC
47-63 Hz
2A MAX
FUSE
TYPE T 3A GDC
250 VOLT
FOR 100 - 240 V~
~
FIGURE 2.4 Fuse Location and Spare Fuse
2000-318/324 Manual_Rev 0 Page 7 11/23/09
2.5 Environmental Use Information
A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your eqipment rack.
B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C. Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used, when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connection to the Branch
(use of power strips).
G. Top Cover - There are no servicable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE RE-INSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
2000-318/324 Manual_Rev 0 Page 8 11/23/09
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2000-318/324 Manual_Rev 0 Page 9 11/23/09
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Cross Technologies 2000-318 User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Cross Technologies 2000-02 Owner's manual
-
-
-
-
-
-
-
-
-