American Standard 7105.152.243 Installation guide

Category
Sanitary ware
Type
Installation guide

American Standard 7105.152.243, a vessel lavatory faucet, offers a sleek design and reliable performance for your bathroom. Crafted with durable materials, this faucet features a single handle for effortless water control and temperature adjustment. Enjoy a smooth, steady water flow with its aerated stream, making it ideal for everyday use. Installation is made simple with the provided instructions, allowing you to easily upgrade your bathroom with a stylish and functional fixture.

American Standard 7105.152.243, a vessel lavatory faucet, offers a sleek design and reliable performance for your bathroom. Crafted with durable materials, this faucet features a single handle for effortless water control and temperature adjustment. Enjoy a smooth, steady water flow with its aerated stream, making it ideal for everyday use. Installation is made simple with the provided instructions, allowing you to easily upgrade your bathroom with a stylish and functional fixture.

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965781 Rev. 1.0 (1/18)
INSTALL FAUCET
STUDIO
®
S
VESSEL LAVATORY FAUCET
INSTALLATION
INSTRUCTIONS
7105.152
Screwdriver Adjustable Wrench Tubing CutterChannel Locks
Certied to comply with ANSI A112.18.1M
1
2
4
MOUNTING
SURFACE
3
6
5
7
CAUTION
Turn off hot and cold water
supplies before begining.
Seat SEAL (1) into under side of FAUCET BASE (2).
Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4)
through hole in mounting surface.
From below, install SUPPORT PLATE (7) GASKET (5) and
MOUNTING NUT (6) onto SHANK (4). Secure Faucet with
MOUNTING NUT (6). Before nal tightening, adjust Faucet
so that it is centered. Tighten MOUNTING NUT (6) to
complete mounting.
Note: For thick deck installations, the SUPPORT PLATE (7)
can be omitted.
- 2 -
2
MAKE WATER SUPPLY AND WASTE CONNECTIONS
M965781 Rev. 1.0 (1/18)
2
APPROX. 20"
1
COLD
HOT
3/8" COMPRESSION
BLUE
BAND
RED
BAND
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression.
Connect right SUPPLY (2) to Hot (Marked with a Red Band)
and left supply to COLD (1) wall supply.
Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
Connect 1-1/4" O.D. tail piece on POP-UP DRAIN to
waste outlet.
3
DRAIN ASSEMBLY (6542.140/.170)
Apply a bead of PUTTY around underside of DRAIN FLANGE (1)
ange. Insert DRAIN PLUG (2) into SINK drain hole.
Hold DRAIN PLUG (2) to prevent turning and assemble
GASKET (3), WASHER (4) and LOCKNUT (5) from underneath
sink.
Apply sealant to threaded end of TAILPIECE (6) and thread into
lower end of DRAIN PLUG. Connect other end to trap.
PUTTY
SINK
SEALANT
1
3
5
6
2
4
- 3 -
M965781 Rev. 1.0 (1/18)
With HANDLE (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Remove AERATOR (3).
Operate HANDLE (1) to ush water lines thoroughly.
Replace AERATOR (3).
TEST INSTALLED FITTING
4
1
3
OFF
ON
“P” TRAP
WASTE
OUTLET
2
2
HOT
COLD
5
6
To remove or replace cartridge:
– Turn valve to OFF position.
– Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).
– Pull off HANDLE ASSEMBLY (3).
– Unthread CARTRIDGE NUT (5) using a 7/8" socket (deep socket)
and remove.
– Pull out CARTRIDGE (6).
– Inspect CARTRIDGE (6) and O-RINGS (7) for debris and
clean if necessary.
– Clean MANIFOLD (8) and rinse clean.
– Reinstall CARTRIDGE (6) and O-RINGS (7) onto
MANIFOLD (8).
– Reinstall CARTRIDGE NUT (5) and CAP (4) (orientation of the
cap is very important).
– When reinstalling the HANDLE (3) push the lower gear back
(as shown in the gure) then install HANDLE (3) in pushed down
position (make sure the seal alligns with the body).
– Push SEAL (4) down, ensuring that it is completely pushed into
the spout body.
– Reinstall HANDLE SCREW (2) and PLUG BUTTON (1).
SERVICE
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CAUTION
Turn off hot and cold water
supplies before beginning.
8
5
6
REMOVE
INSTALL
7
10
4
1
2
2.5mm HEX KEY
3
LOWER GEAR
- 4 -
M951430-0070A
CARTRIDGE
M970230-YYY0A
HANDLE KIT
M970231-0070A
GEAR AND PLUG KIT
M923840-0070A
AERATOR
(1.2 GPM)
M970248-YYY0A
PLUG BUTTON & SCREW
M953455-YYY0A
DRAIN COMPLETE
070532-0040A
TAILPIECE
M961634-0070A
VALVE MTG. KIT
A923480-0070A
SUPPORT PLATE
- 4 -
M965781 Rev. 1.0 (1/18)
STUDIO
®
S
VESSEL LAVATORY
FAUCET
MODEL NUMBER
7105.152
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 002
BRUSHED NICKEL 295
MATTE BLACK 243
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard 7105.152.243 Installation guide

Category
Sanitary ware
Type
Installation guide

American Standard 7105.152.243, a vessel lavatory faucet, offers a sleek design and reliable performance for your bathroom. Crafted with durable materials, this faucet features a single handle for effortless water control and temperature adjustment. Enjoy a smooth, steady water flow with its aerated stream, making it ideal for everyday use. Installation is made simple with the provided instructions, allowing you to easily upgrade your bathroom with a stylish and functional fixture.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI