Honeywell Ademco -10SE User manual

Brand: Honeywell

Model: Ademco -10SE

Category: Security access control systems

Type: User manual

This manual is also suitable for

Ademco Vista

ÊK5309-1QGDŠ

K5309-1QG 12/11 Rev A Part 1

TESTING THE SYSTEM

Using the Test mode allows each detection point to be checked for

proper operation. Testing should be conducted weekly to

ensure proper operation.

• The keypad sounds a single beep about every 30 seconds as a

reminder that the system is in the Test mode.

• Alarm messages are not sent to your Central Station while Test

mode is on.

If a problem is experienced with any detection point (no confirming

sounds, no display), call for service immediately.

1. Disarm the system and close all protected windows, doors, etc.

The READY indicator light should come on if all zones are intact

2. Enter your 4-digit Master code + 5 + 0 (walk)

3. Listen. The external sounder should sound for about 1 second

then turn off. If the sounder does not sound, CALL FOR SERVICE.

The “Test in Progress” display appears only on the keypad that

started the test.

4. Fault zones. Open each protected door and window in turn and

listen for three beeps from the keypad. Each faulted detection

point should appear on the display. The display clears when the

door or window is closed.

5. Walk in front of any interior motion detectors (if used) and listen

for three beeps. Each detector should appear on the display when

it is activated. The display clears when no motion is detected.

Note

that if wireless motion detectors are used, there is a 3-minute

delay between activations to conserve battery life.

6. Test all smoke detectors

, following the manufacturer's instructions.

7. When all detection points have been checked and are intact

(closed), there should be no zone numbers displayed.

8. Exit test mode: 4-digit code + 1

TROUBLE CONDITIONS

The word CHECK on the keypad's display, accompanied by a

"beeping" at the keypad, indicates a trouble condition in the system

at the displayed zone number sensor and requires your attention.

Determine if the zone(s) displayed are intact and make them so if

they are not. If the display persists, CALL FOR SERVICE.

To silence the beeping for these conditions, press any key.

Typical Trouble conditions include the following:

Trouble Message Meaning

COMM. FAILURE

(or FC)

A failure has occurred in the telephone

communication portion of your system.

SYSTEM LO BAT

(or BAT with no zone No.)

Low system battery condition exists.

LO BAT+ zone descriptor

(or BAT with zone No.)

Low battery condition in the wireless

transmitter. Either replace the battery

yourself, or CALL FOR SERVICE.

Rcvr Jam (or CHECK 90) RF interference in wireless system which may

impede reception from wireless sensors.

ALARM 1xx (or 91)

FAULT 1xx

CHECK 1xx

A communication problem between the control

and a connected device (e.g., RF receiver,

zone expander) where the “xx” indicates the

device address.

MODEM COMM (or CC) Indicates that the control is on-line with the

Central Monitoring Station's remote computer.

BELL FAILURE (or CHECK

70)

Indicates that the wiring connection to the

external sounder is at fault.

AC LOSS (or NO AC) The system is operating on battery power only

due to an AC power failure.

If only some lights are out on the premises,

check circuit breakers and fuses and reset or

replace as needed.

OPEN CIRCUIT

(or OC)

The keypad is not receiving signals from the

control.

Long Rng Trbl (or bF) Back-up communication device (if used) has

failed.

TELCO FAULT (or CHECK 94)

The telephone line has a problem.

Busy-Standby

(or dI)

If this message remains displayed for more

than 1 minute, system is disabled. CALL FOR

SERVICE.

SETTING THE DATE AND TIME

NOTE: All partitions must be disarmed before date/time can be set.

You can set the time and date by doing the following:

1. +[#] + [6] [3]

(Master Code)

2. Press [∗] when the time/date is displayed.

A cursor appears under the first digit of the hour.

To move cursor ahead, press [∗]. To go back, press [#].

• Enter the 2-digit hour setting.

• Enter the 2-digit minute setting.

• Press [1] for PM or [2] for AM.

• Enter the last two digits of the current year.

• Enter the 2-digit month setting.

• Enter the 2-digit day setting.

3. To exit, press [∗] when cursor is at the last digit, or wait 30

seconds.

NOTES

SERVICING INFORMATION

Your local Honeywell dealer is the person best qualified to service

your alarm system. Arranging some kind of regular service

program with him is advisable. Your local Honeywell dealer is:

Name:

Address:

Phone:

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ADEMCO VISTA SERIES SECURITY SYSTEMS

VISTA-20P / VISTA-20PSIA -- VISTA-15P / VISTA-15PSIA

Quick Guide to User Functions

Full User Guide Available Online: This Quick Guide describes the most frequently used features and functions of your system. For

full details of all user functions, please see the system’s User Guide located online at:

http://www.security.honeywell.com/hsc/products. The full version User Guide is also available from your installer upon request.

Congratulations on your ownership of a Honeywell Security System. This system provides:

• Three forms of detection: burglary, fire and emergency (see your installer for which forms of detection are installed)

• At least one keypad which provides control of system and displays system status

• Various sensors for perimeter and interior burglary detection

• Optional smoke or combustion detectors designed to provide early warning in case of fire.

Your system may also be programmed to automatically send alarm and status messages to a Central Monitoring Station.

SYSTEM BASICS

The following is a list of some of the most common features and

functions of your system:

• Several modes of burglary detection: Stay, Night-Stay, Away,

Instant, Maximum.

• Bypass feature lets you bypass selected zones while leaving the

rest of the system armed.

• Chime mode alerts you to the opening of protected doors and

windows while the system is disarmed.

• Fire and carbon monoxide detection are always active (if

installed) and an alarm sounds if a fire or carbon monoxide

condition is detected.

• Panic keys (if programmed) let you manually initiate a fire and

personal alarms using the keypad.

• 4-digit security codes are used in conjunction with keypad

command to perform system functions.

• Each user can be assigned a different security code, each with

different authority levels.

• The system sensing devices have been assigned to various

“zones,” which are specific areas of detection (e.g., front door,

kitchen window, etc.).

• Zone numbers (points of detection) are displayed at the keypad

when an alarm or trouble condition occurs.

• Partitions (VISTA-20P Series) provide two independent areas of

detection plus an optional common zone area, with each partition

containing a group of zones that can be armed and disarmed

without affecting other zones or users.

• Function keys may have been programmed to perform various

functions. Ask your installer if these keys are active.

• A Scheduling feature can be programmed to automatically

perform certain functions (e.g., arm the system) at a

predetermined time each day. See the full User Guide for details.

ENTRY/EXIT DELAYS

• Entry Delays give you time to disarm the system when you

enter through the designated entrance door.

• You must disarm the system before the entry delay period ends,

or an alarm will occur (keypad beeps during the entry delay

period, reminding you to disarm the system).

• Exit delay gives you time after arming the system to leave

through the designated exit door(s) without setting off an alarm.

If programmed, a slow beeping will sound during the exit delay

period until the last 10 seconds, which then changes to fast

beeping (alerting you to the end of exit delay). If you cannot

leave within this delay time period, you should stop, disarm the

system, and start over to avoid a false alarm.

•

••

• See your installer for your delay times. See the full User Guide

for details on Exit Error alarms.

NOTES on BURGLARY DETECTION

• The system must be armed before the burglary detection can

sense intrusions.

• To arm your system, enter your security code followed by the

desired arming key.

• To disarm the system, enter your security code then press the

OFF key.

• When an alarm occurs, the keypad sounds and displays the

zone(s) causing the alarm. The external sounder may also

sound.

• If your system is connected to a Central Monitoring Station, an

alarm message is also sent (delayed 30 seconds by default to

reduce false alarms).

• To stop the alarm sounding, simply disarm the system.

• Memory of Alarm: When an alarm condition occurs, the

keypad displays the number(s) of the zone(s) that caused the

problem, and displays the type of alarm. Clear the Memory of

Alarm display by entering another “off” sequence.

IMPORTANT: If you return to the premises and the

main burglary sounder is on, or the keypad beeps

rapidly upon entering the premises, it indicates that

an alarm has occurred during your absence and an

intruder may still be on the premises. LEAVE

IMMEDIATELY and CONTACT THE POLICE from a

nearby safe location.

NOTES on FIRE and CO DETECTION

• Your fire alarm system (if installed) is on 24 hours a day, for

continuous detection. In the event of an emergency, the

smoke and heat detectors sound their alarms, triggering a

loud, interrupted pulsed sound from the Keypad(s) and any

external sounders.

• You can silence the alarm at any time by pressing the OFF key

(the security code is not needed to silence fire alarms).

• Carbon monoxide (CO) detectors, if installed, provide

continuous detection. If a high level of carbon monoxide is

detected, an interrupted pulsed alarm sound occurs at the

keypads and the detector(s). Immediately move to a spot

where fresh air is available, preferably outdoors. From a safe

area, call your security service provider for further

instructions. To silence the keypad sounding, press the OFF

key. To silence the detector, see its instructions.

BYPASSING ZONES

Use the 6 BYPASS key when you want to arm your system with one or more zones

intentionally unprotected. The system must be disarmed first.

Mode Press these keys… What happens

BYPASS

ZONES

4-digit code + 6 +

2-digit zone numbers

to be bypassed

• When finished, the keypad will momentarily display

a "Bypass" message for each bypassed zone

number. Wait for all bypassed zones to be displayed.

• Arm the system as usual. When armed, the arming

message is displayed with “ZONE BYPASSED.”

• Bypassed zones are unprotected and will not cause

an alarm if violated.

• The system will not allow fire zones to be bypassed.

• Zones are automatically unbypassed when the

system is disarmed.

• To display bypassed zones prior to arming, enter

your security code and press the BYPASS key.

PANIC KEYS

Your system may have been programmed to use special keys or key pairs to manually

activate emergency (panic) functions as follows:

This Function Key(s)* Sends This Signal** With This Sounding…

Silent Alarm silent alarm no audible alarm; displays, “Press [∗]

to show faults,” indicating that a silent

alarm has been initiated.

Audible Alarm audible alarm a loud, steady alarm at keypad(s) and

at any external sounders that may be

connected.

Personal Alarm auxiliary alarm steady alarm sound at keypad(s), but

not at external bells or sirens.

Fire Alarm fire alarm temporal (pulsing) sound at external

bells and sirens.

* Enter the appropriate keys programmed by your installer for each function (see installer).

** All panic functions send signals to the Central Monitoring Station, if connected.

To activate a Panic Function:

Press and hold down for at least 2 seconds

the programmed lettered key or key pair

for the desired emergency function (or

press both keys of the assigned key pair at

the same time).

Keys Pairs Displayed as Zone

[A] (∗

∗∗

∗/1) 95

[B] (∗

∗∗

∗/#) 99

[C] (3/#) 96

NOTE: The [D] key may be programmed

for other purposes; see your installer.

CHECKING OPEN ZONES

Checking Zones: Before arming your system, all protected doors, windows and other

detection zones must be closed or bypassed; otherwise the keypad displays "Not Ready."

GOTO: If the user is authorized, a keypad in one partition can be used to perform system

functions in the other partition by using the GOTO command. Must use an Alpha keypad.

Mode Press these keys… What happens

CHECK

ZONES ∗

∗∗

∗ • Displays all faulted zones.

GOTO

4-digit code +

∗

∗∗

∗

partition number

(1,2,3 = go to partition;

0 = return to home part.)

• The keypad beeps to confirm the partition change.

• Keypads automatically return to their original

partition after 30 seconds with no keypad activity.

ARMING THE SYSTEM, CHIME MODE, and CONTROLLING DEVICES

Before arming, close all perimeter doors and windows and make sure the Ready to Arm

message is shown.

After arming, leave the premises through an entry/exit door during the exit delay period and

be sure the door is reclosed to avoid causing an alarm.

Mode Press these keys… When to use an arming mode and what happens

STAY

4-digit code + 3

three beeps confirm

• Used when you want to arm the system with

persons staying inside (or if you have pets that are

moving throughout the premises).

• Arms perimeter zones; interior zones left disarmed.

• An alarm sounds if any protected window or non-

entry/exit door is opened.

NIGHT-

STAY

4-digit code + 3 3

three beeps confirm

• Use NIGHT-STAY mode to provide increased

security while staying inside.

• Arms same as STAY mode, but also arms

preselected interior sensors (set by your installer).

INSTANT

4-digit code + 7

three beeps confirm

• Used when staying inside and do not expect anyone

to use an entry/exit door.

• Same as STAY mode, except entry delay is off.

• An alarm sounds same as STAY mode, and sounds

upon opening entry/exit doors.

AWAY

4-digit code + 2

two beeps confirm

• Used when nobody is staying inside (including pets).

• Arms the entire system (interior and perimeter).

• An alarm sounds if a protected window or any door

is opened, or if any movement is detected inside.

MAXIMUM

4-digit code + 4

two beeps confirm

• Used when leaving the premises for extended

periods (e.g., vacation).

• Same as Away mode, except entry delay is off.

• An alarm sounds same as Away mode, and sounds

upon opening entry/exit doors.

QUICK

ARMING # + arming key

• If programmed, you can press the [#] key in place

of your security code when arming the system

CHIME

MODE

4-digit code + 9

(enter again to turn

Chime mode off)

• Alerts you to the opening of a perimeter door or

window while the system is disarmed.

• Three tones sound at the keypad whenever a

perimeter door or window is opened (interior zones

do not produce a tone when they are faulted).

• Pressing the READY key displays the open zones.

Turning

Devices

On and

Off

Turn ON a Device:

4-digit code + # +

7 + device number

Turn OFF a Device:

4-digit code + # +

8 + device number

• You may be able to override automatically

controlled devices using the Device commands.

• Some devices can be manually turned on or off

using the Device commands.

• Devices are assigned 2-digit device numbers.

• See your Installer for details on controlling devices.

DISARMING THE SYSTEM and SILENCING ALARMS

The 1 OFF key is used to disarm the system, silence alarm and trouble sounds, and clear

memory of alarm displays.

Mode Press these keys… What happens

DISARM

and

SILENCE

ALARMS

4-digit code + 1

• System is disarmed and alarm sounding is silenced.

• To clear the memory of alarm display (if present),

enter your 4-digit code + 1 again.

• To Silence a Fire Alarm or Carbon Monoxide Alarm

Simply press the 1 key (no code needed)

V20P-Quik-Guide

ARMING

KEYS

BYPASSING

ZONES

CHIME

MODE

QUICK

ARMING

TESTING

THE SYSTEM

ADDING SECURITY

CODES

CHECKING

ZONES

ARMED

READY

ARMING KEYS

(NO DELAY)

DISARM

KEY

OFF

MAX

INSTANT

READY

AWAY

TEST

CODE

STAY

BYPASS

CHIME

• When entering codes and commands, sequential key depressions must be made within 4-5

seconds of one another. If 4-5 seconds elapse without a key depression, the entry will be

aborted and must be repeated from its beginning.

• If you make a mistake while entering a security code, stop, press the

∗

∗∗

∗

key, and then

start over. If you stop in the middle while entering a code, and then immediately start the

entry over, an erroneous code might be entered.

SECURITY CODES

Your installer assigned a master code that is used to perform all system functions.

In addition, other security codes can be assigned for use by other users.

• Only the System Master and Partition Master can assign security codes to users.

• Users are identified by 2-digit user numbers.

• Only the System Master can change user partitions.

• In addition to a security code, each user is assigned an authority level and various system

attributes. See the full User Guide for definitions of each Authority Level.

• Security codes can be used interchangeably within a partition when performing system

functions (a system armed with one security code can be disarmed by a different security

code), with the exception of the Guest and Arm Only codes.

• Security code programming involves these steps:

1. Choose a user number from the set of users assigned to the partition in which the user

will be operating, and assign a 4-digit security code.

2. Assign an authority level to that user.

3. Assign other attributes as necessary.

Assigning Security Codes and User Attributes

The following lists the various command strings for adding security codes and attributes.

NOTE: Partition Master codes (VISTA-20P Series only) apply only to those user numbers

previously assigned (by the system master/installer) to the partition master’s partition.

Function Commands

Change System

Master Code

System Master code + 8 + [02] + new code + new code again

Add Security Code

Master code + 8 + user no. + new user’s security code

The Keypad beeps once to confirm that new user was added.

Delete Security

Code

Master code + 8 + [user no.] + # 0

The security code and all attributes* set for this user number,

including any associated RF keys, are erased from the system.

(*except assigned partition)

Authority Level

Master code + 8 + [user no.] + # 1 + auth. level

Authority Levels: 0 = standard user

1 = arm only

2 = guest

3 = duress

4 = partition master (VISTA-20P Series only)

Access Group

Master Code + 8 + [user no.] + 8 2 + group (1-8)

You can assign users to a group, then set an access schedule that

defines the times this group of users can operate the system. The

system ignores these users outside the scheduled times.

User’s Partition

System Master Code + 8 + [user no.] + # 3 + 0 + part. + #

This assigns the partitions the user can access. If more than one,

enter partition numbers sequentially, then press [#] to end.

E.g., master code + [8] + [user no.] + [#] [3] + [0] + [1] [2] + [#]

gives the user access to partitions 1 and 2 and common partition.

Partition Entries: 1 = partition 1 and common

2 = partition 2 and common

3 = common partition only

RF User Number

Master/Part. Prog. Code + 8 + [user no.] + # 4 + zone no.

Use this command to assign a wireless button device (keyfob) to

this user (keyfob must be enrolled in system first; see installer).

Zone number: enter the zone number assigned to a button on the

keyfob that will be used for arming/disarming by this user.

Pager On/Off

Master/Part. Prog. Code + 8 + [user no.] + # 5 + 0 or 1

You can program a user so that a message is sent to a pager

whenever this code is used to arm or disarm the system.

Paging On/Off: 1 = allow paging

0 = no paging for this user

Honeywell Ademco -10SE User manual

Brand: Honeywell

Model: Ademco -10SE

Category: Security access control systems

Type: User manual

This manual is also suitable for

Ademco Vista

Download PDF

report

Honeywell Ademco -10SE User manual

This manual is also suitable for

Honeywell Ademco -10SE User manual

Related papers

Other documents