KTM 350 SX-F 2014 Owner's manual

OWNER'S MANUAL 2014

350 SX‑F EU

350 SX‑F USA

350 XC‑F USA

Art. no. 3213032en

DEAR KTM CUSTOMER 1

DEAR KTM CUSTOMER

Congratulations on your decision to purchase a KTM motorcycle. You are now the owner of a state-of-the-art sports motorcycle that will

give you enormous pleasure if you service and maintain it accordingly.

We wish you a lot of enjoyment in riding this vehicle.

Enter the serial numbers of your vehicle below.

Chassis number ( p. 10) Dealer's stamp

Engine number ( p. 10)

The Owner's Manual contained the latest information for this model at the time of going to print. Slight deviations resulting from con-

tinuing development and design can, however, not be completely excluded.

All specifications are non-binding. KTM Sportmotorcycle AG specifically reserves the right to modify or delete technical specifica-

tions, prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt

these to local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery

options, deviations from illustrations and descriptions, as well as misprints and other errors. The models portrayed partly contain spe-

cial equipment that does not belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright

owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead

to the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM-Sportmotorcycle AG

5230 Mattighofen, Austria

TABLE OF CONTENTS 2

TABLE OF CONTENTS

1 MEANS OF REPRESENTATION ..................................... 4

1.1 Symbols used ................................................... 4

1.2 Formats used.................................................... 4

2 SAFETY ADVICE........................................................... 5

2.1 Use definition - intended use ............................. 5

2.2 Safety advice.................................................... 5

2.3 Degrees of risk and symbols............................... 5

2.4 Tampering warning............................................ 5

2.5 Safe operation .................................................. 5

2.6 Protective clothing ............................................ 6

2.7 Work rules........................................................ 6

2.8 Environment..................................................... 6

2.9 Owner's Manual ................................................ 6

3 IMPORTANT NOTES..................................................... 7

3.1 Guarantee, warranty .......................................... 7

3.2 Operating and auxiliary substances ..................... 7

3.3 Spare parts, accessories .................................... 7

3.4 Service ............................................................ 7

3.5 Figures ............................................................ 7

3.6 Customer service............................................... 7

4 VIEW OF VEHICLE ....................................................... 8

4.1 View of vehicle, front left (example) .................... 8

4.2 View of vehicle, rear right (example) ................... 9

5 SERIAL NUMBERS .................................................... 10

5.1 Chassis number .............................................. 10

5.2 Type label ...................................................... 10

5.3 Engine number ............................................... 10

5.4 Fork part number ............................................ 10

5.5 Shock absorber part number ............................ 10

6 CONTROLS................................................................ 11

6.1 Clutch lever.................................................... 11

6.2 Hand brake lever............................................. 11

6.3 Throttle grip ................................................... 11

6.4 Kill switch...................................................... 11

6.5 Electric starter button...................................... 11

6.6 Overview of indicator lamps ............................. 12

6.7 Opening the filler cap...................................... 12

6.8 Closing the filler cap ....................................... 13

6.9 Cold start button............................................. 13

6.10 Idle speed adjusting screw............................... 14

6.11 Shift lever ...................................................... 14

6.12 Foot brake lever .............................................. 15

6.13 Plug-in stand (All SX‑F models)........................ 15

6.14 Side stand (XC‑F)............................................ 15

7 PREPARING FOR USE................................................ 16

7.1 Advice on first use .......................................... 16

7.2 Running in the engine ..................................... 17

7.3 Preparing the vehicle for difficult riding

conditions ...................................................... 17

7.4 Preparing for rides on dry sand......................... 18

7.5 Preparing for rides on wet sand ........................ 18

7.6 Preparing for rides on wet and muddy

surfaces ......................................................... 19

7.7 Preparing for rides at high temperature and

slow speed ..................................................... 19

7.8 Preparing for rides at low temperatures or in

snow.............................................................. 19

8 RIDING INSTRUCTIONS............................................. 20

8.1 Checks and maintenance work when preparing

for use ........................................................... 20

8.2 Starting.......................................................... 20

8.3 Starting off..................................................... 21

8.4 Shifting, riding ............................................... 21

8.5 Applying the brakes......................................... 21

8.6 Stopping, parking............................................ 21

8.7 Transport ....................................................... 22

8.8 Refueling ....................................................... 22

9 SERVICE SCHEDULE ................................................. 24

9.1 Service schedule............................................. 24

9.2 Service work (as additional order) ..................... 25

10 TUNING THE CHASSIS .............................................. 26

10.1 Checking the basic chassis setting with the

rider's weight.................................................. 26

10.2 Compression damping of the shock absorber...... 26

10.3 Adjusting the low-speed compression damping

of the shock absorber ...................................... 26

10.4 Adjusting the high-speed compression

damping of the shock absorber......................... 27

10.5 Adjusting the rebound damping of the shock

absorber......................................................... 28

10.6 Measuring rear wheel sag unloaded................... 28

10.7 Checking the static sag of the shock absorber.... 29

10.8 Checking the riding sag of the shock absorber.... 29

10.9 Adjusting the spring preload of the shock

absorber x.................................................... 29

10.10 Adjusting the riding sag x.............................. 30

10.11 Checking the basic setting of the fork ............... 31

10.12 Adjusting the compression damping of the

fork ............................................................... 32

10.13 Adjusting the rebound damping of the fork ........ 32

10.14 Handlebar position.......................................... 33

10.15 Adjusting the handlebar position x ................. 34

11 SERVICE WORK ON THE CHASSIS.............................. 35

11.1 Raising the motorcycle with the lift stand.......... 35

11.2 Removing the motorcycle from the lift stand...... 35

11.3 Bleeding the fork legs...................................... 35

11.4 Cleaning the dust boots of the fork legs............. 36

11.5 Loosening the fork protection ........................... 36

11.6 Positioning the fork protection.......................... 36

11.7 Removing the fork legs x ............................... 37

11.8 Installing the fork legs x................................ 37

11.9 Removing the fork protector x ........................ 38

11.10 Installing the fork protector x......................... 38

11.11 Removing the lower triple clamp x.................. 38

11.12 Installing the lower triple clamp x .................. 39

11.13 Checking the steering head bearing play............ 41

11.14 Adjusting the play of the steering head

bearing x ..................................................... 41

11.15 Greasing the steering head bearing x .............. 42

11.16 Removing the start number plate...................... 42

11.17 Installing the start number plate....................... 42

11.18 Removing the front fender ............................... 42

11.19 Installing the front fender ................................ 43

11.20 Removing the shock absorber x...................... 43

11.21 Installing the shock absorber x....................... 44

11.22 Removing the seat .......................................... 44

11.23 Mounting the seat........................................... 44

11.24 Removing the air filter box lid .......................... 45

11.25 Installing the air filter box lid ........................... 45

11.26 Removing the air filter x................................ 45

11.27 Cleaning the air filter and air filter box x ......... 46

11.28 Installing the air filter x................................. 46

11.29 Securing the air filter box lid x....................... 47

11.30 Sealing the air filter box x.............................. 47

TABLE OF CONTENTS 3

11.31 Removing the manifold x............................... 47

11.32 Installing the manifold x................................ 48

11.33 Removing the main silencer ............................. 49

11.34 Installing the main silencer.............................. 49

11.35 Changing the glass fiber yarn filling of the

main silencer x............................................. 50

11.36 Removing the fuel tank x............................... 50

11.37 Installing the fuel tank x................................ 51

11.38 Checking for chain dirt accumulation................ 52

11.39 Cleaning the chain .......................................... 53

11.40 Checking the chain tension .............................. 53

11.41 Adjusting the chain tension.............................. 54

11.42 Checking the chain, rear sprocket, engine

sprocket, and chain guide................................ 54

11.43 Checking the frame x .................................... 56

11.44 Checking the swingarm x............................... 56

11.45 Checking the throttle cable routing ................... 56

11.46 Checking the rubber grip ................................. 57

11.47 Additionally securing the rubber grip................. 57

11.48 Adjusting the basic position of the clutch

lever .............................................................. 57

11.49 Checking/correcting the fluid level of the

hydraulic clutch.............................................. 58

11.50 Changing the hydraulic clutch fluid x.............. 58

12 BRAKE SYSTEM ........................................................ 59

12.1 Checking the free travel of the hand brake

lever .............................................................. 59

12.2 Adjusting the basic position of the hand brake

lever .............................................................. 59

12.3 Checking the brake discs ................................. 59

12.4 Checking the brake fluid level of the front

brake ............................................................. 60

12.5 Adding front brake fluid x.............................. 60

12.6 Checking the front brake linings ....................... 61

12.7 Changing the front brake linings x.................. 61

12.8 Checking the free travel of foot brake lever ........ 63

12.9 Adjusting the basic position of the foot brake

lever x ......................................................... 63

12.10 Checking the rear brake fluid level.................... 64

12.11 Adding rear brake fluid x ............................... 64

12.12 Checking the rear brake linings ........................ 65

12.13 Changing the rear brake linings x ................... 65

13 WHEELS, TIRES ........................................................ 67

13.1 Removing the front wheel x ........................... 67

13.2 Installing the front wheel x ............................ 67

13.3 Removing the rear wheel x............................. 68

13.4 Installing the rear wheel x.............................. 68

13.5 Checking the tire condition .............................. 69

13.6 Checking the tire air pressure........................... 70

13.7 Checking the spoke tension.............................. 70

14 ELECTRICAL SYSTEM ................................................ 71

14.1 Removing the battery x.................................. 71

14.2 Installing the battery x .................................. 71

14.3 Charging the battery x................................... 71

14.4 Changing the main fuse................................... 72

15 COOLING SYSTEM ..................................................... 74

15.1 Cooling system ............................................... 74

15.2 Checking the antifreeze and coolant level.......... 74

15.3 Checking the coolant level ............................... 74

15.4 Draining the coolant x................................... 75

15.5 Refilling coolant x......................................... 76

16 TUNING THE ENGINE................................................ 77

16.1 Checking the play in the throttle cable .............. 77

16.2 Adjusting the play in the throttle cable x......... 77

16.3 Adjusting the idle speed x ............................. 78

16.4 Checking the basic position of the shift lever ..... 78

16.5 Adjusting the basic position of the shift

lever x ......................................................... 78

17 SERVICE WORK ON THE ENGINE ............................... 79

17.1 Changing the fuel screen x ............................ 79

17.2 Checking the engine oil level............................ 79

17.3 Changing the engine oil and oil filter, cleaning

the oil screen x............................................. 80

17.4 Adding engine oil............................................ 82

18 CLEANING, CARE ...................................................... 83

18.1 Cleaning the motorcycle .................................. 83

19 STORAGE.................................................................. 84

19.1 Storage .......................................................... 84

19.2 Preparing for use after storage.......................... 84

20 TROUBLESHOOTING ................................................. 85

21 BLINK CODE ............................................................. 87

22 TECHNICAL DATA...................................................... 88

22.1 Engine ........................................................... 88

22.2 Engine tightening torques ................................ 89

22.3 Capacities ...................................................... 90

22.3.1 Engine oil .................................................. 90

22.3.2 Coolant...................................................... 90

22.3.3 Fuel .......................................................... 90

22.4 Chassis .......................................................... 90

22.5 Electrical system............................................. 91

22.6 Tires.............................................................. 91

22.7 Fork............................................................... 92

22.7.1 SX‑F EU..................................................... 92

22.7.2 SX‑F USA................................................... 92

22.7.3 XC‑F.......................................................... 92

22.8 Shock absorber............................................... 93

22.8.1 SX‑F EU..................................................... 93

22.8.2 SX‑F USA................................................... 93

22.8.3 XC‑F.......................................................... 94

22.9 Chassis tightening torques ............................... 95

23 SUBSTANCES ........................................................... 96

24 AUXILIARY SUBSTANCES .......................................... 98

25 STANDARDS ........................................................... 100

INDEX ............................................................................ 101

1 MEANS OF REPRESENTATION 4

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

All work marked with this symbol requires specialist knowledge and technical understanding. In the interest of

your own safety, have these jobs performed by an authorized KTM workshop. There, your motorcycle will be opti-

mally cared for by specially trained experts using the specialist tools required.

Indicates a page reference (more information is provided on the specified page).

1.2 Formats used

The typographical formats used in this document are explained below.

Specific name Identifies a proprietary name.

Name

®

Identifies a protected name.

Brand™ Identifies a brand available on the open market.

2 SAFETY ADVICE 5

2.1 Use definition - intended use

KTM sport motorcycles are designed and built to withstand the normal stresses and strains of competitive use. The motorcycles com-

ply with currently valid regulations and categories of the top international motorsport organizations.

Info

The motorcycle may only be used in closed off areas remote from public road traffic.

2.2 Safety advice

A number of safety instructions need to be followed to operate the vehicle safely. Therefore, read this manual carefully. The safety

instructions are highlighted in the text and are referred to at the relevant passages.

Info

The vehicle has various information and warning labels at prominent locations. Do not remove information/warning labels. If

they are missing, you or others may not recognize dangers and may therefore be injured.

2.3 Degrees of risk and symbols

Danger

Identifies a danger that will immediately and invariably lead to fatal or serious permanent injury if the appropriate measures

are not taken.

Warning

Identifies a danger that is likely to lead to fatal or serious injury if the appropriate measures are not taken.

Caution

Identifies a danger that may lead to minor injuries if the appropriate measures are not taken.

Note

Identifies a danger that will lead to considerable machine and material damage if the appropriate measures are not taken.

Warning

Identifies a danger that will lead to environmental damage if the appropriate measures are not taken.

2.4 Tampering warning

Tampering with the noise control system is prohibited. Federal law prohibits the following acts or the causing thereof:

1 The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement, of any device

or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate

purchaser or while it is in use, or

2 the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.

Among those acts presumed to constitute tampering are the acts listed below:

1 Removal or puncturing of the main silencer, baffles, header pipes or any other components which conduct exhaust gases.

2 Removal or puncturing of parts of the intake system.

3 Lack of proper maintenance.

4 Replacing moving part of the vehicle, or parts of the exhaust or intake system, with parts other than those specified by the manu-

facturer.

2.5 Safe operation

Danger

Danger of accidents Danger arising from the rider's judgement being impaired.

– Do not operate the vehicle while under the influence of alcohol, drugs and certain medications or physically or mentally

impaired.

Danger

Danger of poisoning Exhaust gases are toxic and inhaling them may result in unconsciousness and/or death.

– When running the engine, always make sure there is sufficient ventilation, and do not start or run the engine in an enclosed

space without an effective exhaust extraction system.

2 SAFETY ADVICE 6

Warning

Danger of burns Some vehicle components become very hot when the vehicle is operated.

– Do not touch hot components such as exhaust system, radiator, engine, shock absorber, and the brake system. Allow these

components to cool down before starting work on them.

Only operate the vehicle when it is in perfect technical condition, in accordance with its intended use, and in a safe and environmen-

tally compatible manner.

The vehicle should only be used by trained persons.

Have malfunctions that impair safety promptly eliminated by an authorized KTM workshop.

Adhere to the information and warning labels on the vehicle.

2.6 Protective clothing

Warning

Risk of injury Missing or poor protective clothing presents an increased safety risk.

– Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always

wear protective clothing that is in good condition and meets the legal requirements.

In the interest of your own safety, KTM recommends that you only operate the vehicle while wearing protective clothing.

2.7 Work rules

Special tools are necessary for certain tasks. The tools are not contained in the vehicle but can be ordered under the number in paren-

theses. E.g.: bearing puller (15112017000)

During assembly, non-reusable parts (e.g. self-locking screws and nuts, seals and seal rings, O-rings, pins, lock washers) must be

replaced by new parts.

In some instances, a thread locker (e.g. Loctite

®

) is required. The manufacturer instructions for use must be followed.

After disassembly, clean the parts that are to be reused and check them for damage and wear. Change damaged or worn parts.

After you complete the repair or service work, check the operating safety of the vehicle.

2.8 Environment

If you use your motorcycle responsibly, you can ensure that problems and conflicts do not occur. To protect the future of the motorcy-

cle sport, make sure that you use your motorcycle legally, display environmental consciousness, and respect the rights of others.

When disposing of used oil, other operating and auxiliary fluids, and used components, comply with the laws and regulations of the

respective country.

Because motorcycles are not subject to the EU regulations governing the disposal of used vehicles, there are no legal regulations that

pertain to the disposal of an end-of-life motorcycle. Your authorized KTM dealer will be glad to advise you.

2.9 Owner's Manual

It is important that you read this Owner's Manual carefully and completely before making your first trip. The Owner's Manual contains

useful information and many tips on how to operate, handle, and maintain your motorcycle. Only then will you find out how to cus-

tomize the vehicle ideally for your own use and how you can protect yourself from injury.

Keep the Owner's Manual in an accessible place to enable you to refer to it as needed.

If you would like to know more about the vehicle or have questions on the material you read, please contact an authorized KTM dealer.

The Owner's Manual is an important component of the vehicle and should be handed over to the new owner if the vehicle is sold.

3 IMPORTANT NOTES 7

3.1 Guarantee, warranty

The work prescribed in the service schedule must be carried out by an authorized KTM workshop only and confirmed in the customer's

Service & Warranty Booklet and in the KTM dealer.net; otherwise, all warranty claims will be void. No warranty claims can be consid-

ered for damage resulting from manipulations and/or alterations to the vehicle.

Additional information on the guarantee or warranty and the procedures involved can be found in the Service & Warranty Booklet.

3.2 Operating and auxiliary substances

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

– Do not allow fuel to get into the ground water, the ground, or the sewage system.

Use operating and auxiliary substances (such as fuel and lubricants) as specified in the Owner's Manual.

3.3 Spare parts, accessories

For your own safety, only use spare parts and accessory products that are approved and/or recommended by KTM and have them

installed by an authorized KTM workshop. KTM accepts no liability for other products and any resulting damage or loss.

Certain spare parts and accessory products are specified in parentheses in the descriptions. Your authorized KTM dealer will be glad

to advise you.

The current KTM PowerParts for your vehicle can be found on the KTM website.

International KTM Website: http://www.ktm.com

3.4 Service

A prerequisite for perfect operation and prevention of premature wear is that the service, care, and tuning work on the engine and

chassis is properly carried out as described in the Owner's Manual. Incorrect adjustment and tuning of the engine and chassis can

lead to damage and breakage of components.

Use of the vehicle under difficult conditions, such as on sand or on wet and muddy surfaces, can lead to considerably more rapid wear

of components such as the drive train, brake system, or suspension components. For this reason, it may be necessary to inspect or

replace parts before the next scheduled service.

It is imperative that you adhere to the stipulated run-in times and service intervals. If you observe these exactly, you will ensure a

much longer service life for your motorcycle.

3.5 Figures

The figures contained in the manual may depict special equipment.

In the interest of clarity, some components may be shown disassembled or may not be shown at all. It is not always necessary to dis-

assemble the component to perform the activity in question. Please follow the instructions in the text.

3.6 Customer service

Your authorized KTM dealer will be happy to answer any questions you may have on your vehicle and KTM.

A list of authorized KTM dealers can be found on the KTM website.

International KTM Website: http://www.ktm.com

4 VIEW OF VEHICLE 8

4.1 View of vehicle, front left (example)

B01411-10

1 Hand brake lever ( p. 11)

2 Clutch lever ( p. 11)

3 Filler cap

4 Plug-in stand ( p. 15)

5 Air filter box lid

6 Engine number ( p. 10)

7 Shift lever ( p. 14)

8 Cold start button ( p. 13)

4 VIEW OF VEHICLE 9

4.2 View of vehicle, rear right (example)

B01412-10

1 Kill switch ( p. 11)

2 Electric starter button ( p. 11)

3 Throttle grip ( p. 11)

4 Chassis number ( p. 10)

4 Type label ( p. 10)

5 Fork part number ( p. 10)

6 Foot brake lever ( p. 15)

7 Idle speed adjusting screw ( p. 14)

8 Shock absorber part number ( p. 10)

5 SERIAL NUMBERS 10

5.1 Chassis number

B01448-10

The chassis number 1 is stamped on the right side of the steering head.

5.2 Type label

B01448-11

The type label 1 is fixed to the front of the steering head.

5.3 Engine number

B01449-10

The engine number 1 is stamped on the left side of the engine under the engine

sprocket.

5.4 Fork part number

B01450-10

The fork part number 1 is stamped on the inner side of the axle clamp.

5.5 Shock absorber part number

B01451-10

The shock absorber part number 1 is stamped on the top of the shock absorber above

the adjusting ring on the engine side.

6 CONTROLS 11

6.1 Clutch lever

C00214-10

The clutch lever 1 is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2 Hand brake lever

B01413-10

Hand brake lever 1 is located on the right side of the handlebar.

The hand brake lever is used to activate the front brake.

6.3 Throttle grip

B01414-10

The throttle grip 1 is fitted on the right side of the handlebar.

6.4 Kill switch

C00217-10

Kill switch 1 is fitted on the left side of the handlebar.

Possible states

• Kill switch in basic position – In this position, the ignition circuit is closed and

the engine can be started.

• Kill switch pressed – In this position, the ignition circuit is interrupted, a run-

ning engine stops, and a non-running engine will not start.

6.5 Electric starter button

B01414-11

Electric starter button 1 is fitted on the right side of the handlebar.

Possible states

• Electric starter button in basic position

• Electric starter button pressed – In this position, the electric starter is actuated.

6 CONTROLS 12

6.6 Overview of indicator lamps

C00218-01

Possible states

FI warning lamp (MIL) lights up/flashes orange – The OBD (on-board

diagnosis) has detected an emission- or safety-critical error.

(XC‑F)

The fuel level warning lamp lights up orange – The fuel level has

reached the reserve mark.

6.7 Opening the filler cap

Danger

Fire hazard Fuel is highly flammable.

– Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no

fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

– The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning Fuel is poisonous and a health hazard.

– Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with

the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with

soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that is contaminated with fuel.

Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

– Do not allow fuel to get into the ground water, the ground, or the sewage system.

B01452-10

(All SX‑F models)

– Turn filler cap 1 counterclockwise and lift it off.

B01453-10

(XC‑F)

– Press release button 1, turn the filler cap counterclockwise, and lift it free.

6 CONTROLS 13

6.8 Closing the filler cap

B01452-11

(All SX‑F models)

– Mount the filler cap and turn it clockwise until the tank is firmly closed.

Info

Run the fuel tank breather hose 1 without kinks.

B01454-10

(XC‑F)

– Replace the filler cap and turn clockwise until the release button 1 locks in

place.

Info

Run the fuel tank breather hose 2 without kinks.

6.9 Cold start button

B01180-10

The cold start button 1 is fitted on the left on the throttle valve body.

The injection system extends the injection time if the engine is cold and the outside

temperature is low. The engine can only burn the increased fuel quantity if it receives

more air. It obtains more air by pulling the cold start button.

Possible states

• The cold start button is activated – The cold start button is pulled out all the way.

• The cold start button is deactivated – The cold start button is pushed in all the

way.

6 CONTROLS 14

6.10 Idle speed adjusting screw

B01446-10

The idle setting of the throttle valve body has a big influence on the starting behavior,

stable idling and the response to throttle opening. This means that an engine with a

correctly set idle speed is easier to start than if the idle is set wrongly.

The idle speed is adjusted with idle speed adjusting screw 1.

Turning the adjusting screw clockwise increases the idle speed.

Turning the adjusting screw counterclockwise lowers the idle speed.

6.11 Shift lever

B01455-10

Shift lever 1 is mounted on the left side of the engine.

B01455-11

(All SX‑F models)

The gear positions can be seen in the photograph.

The neutral or idle position is between the first and second gears.

B01455-12

(XC‑F)

The gear positions can be seen in the photograph.

The neutral or idle position is between the first and second gears.

6 CONTROLS 15

6.12 Foot brake lever

B01456-10

Foot brake lever 1 is located in front of the right footrest.

The foot brake lever is used to activate the rear brake.

6.13 Plug-in stand (All SX‑F models)

B01415-10

The holder for the plug-in stand 1 is the left side of the wheel spindle.

The plug-in stand is used to park the motorcycle.

Info

Remove the plug-in stand before starting on a trip.

6.14 Side stand (XC‑F)

B01457-10

The side stand 1 is on the left side of the vehicle.

B01458-10

The side stand is used to park the motorcycle.

Info

When you are riding, side stand 1 must be folded up and secured with rubber

band 2.

7 PREPARING FOR USE 16

7.1 Advice on first use

Danger

Danger of accidents Danger arising from the rider's judgement being impaired.

– Do not operate the vehicle while under the influence of alcohol, drugs and certain medications or physically or mentally

impaired.

Warning

Risk of injury Missing or poor protective clothing presents an increased safety risk.

– Wear protective clothing (helmet, boots, gloves, pants and jacket with protectors) every time you ride the vehicle. Always

wear protective clothing that is in good condition and meets the legal requirements.

Warning

Danger of crashing Poor vehicle handling due to different tire tread patterns on front and rear wheels.

– The front and rear wheels must be fitted with tires with similar tread patterns to prevent loss of control over the vehicle.

Warning

Danger of accidents Critical riding behavior due to inappropriate riding.

– Adapt your riding speed to the road conditions and your riding ability.

Warning

Danger of accidents Accident risk caused by presence of a passenger.

– Your vehicle is not designed to carry passengers. Do not ride with a passenger.

Warning

Danger of accidents Failure of brake system.

– If the foot brake lever is not released, the brake linings drag continuously. The rear brake may fail due to overheating. Take

your foot off the foot brake lever when you are not braking.

Warning

Danger of accidents Unstable riding behavior.

– Do not exceed the maximum permissible weight and axle loads.

Warning

Risk of misappropriation Usage by unauthorized persons.

– Never leave the vehicle while the engine is running. Secure the vehicle against use by unauthorized persons.

Info

When using your motorcycle, remember that others may feel disturbed by excessive noise.

– Make sure that the pre-delivery inspection work has been carried out by an authorized KTM workshop.

You receive a delivery certificate and the service record at vehicle handover.

– Before your first trip, read the entire operating instructions carefully.

– Get to know the controls.

– Adjust the basic position of the clutch lever. ( p. 57)

– Adjust the basic position of the hand brake lever. ( p. 59)

–

Adjust the basic position of the foot brake lever. x ( p. 63)

–

Adjust the basic position of the shift lever. x ( p. 78)

– Get used to handling the motorcycle on a suitable piece of land before making a longer trip.

Info

Your motorcycle is not authorized for riding on public roads.

Offroad, you should be accompanied by another person on another machine so that you can help each other.

– Try also to ride as slowly as possible and in a standing position to get a better feeling for the vehicle.

– Do not make any offroad trips that over-stress your ability and experience.

– Hold the handlebar firmly with both hands and keep your feet on the footrests when riding.

7 PREPARING FOR USE 17

(All SX‑F models)

– Do not transport luggage.

(XC‑F)

– If you carry any baggage, make sure it is fixed firmly as close as possible to the center of the vehicle and ensure even weight

distribution between the front and rear wheels.

Info

Motorcycles react sensitively to any changes of weight distribution.

– Do not exceed the overall maximum permitted weight and the axle loads.

Guideline

Maximum permissible overall weight 335 kg (739 lb.)

Maximum permissible front axle load 145 kg (320 lb.)

Maximum permissible rear axle load 190 kg (419 lb.)

– Run in the engine. ( p. 17)

7.2 Running in the engine

– During the running-in phase, do not exceed the specified engine speed and engine performance.

Guideline

Maximum engine speed

During the first operating hour 7,000 rpm

Maximum engine performance

During the first 3 operating hours ≤ 75 %

– Avoid fully opening the throttle!

7.3 Preparing the vehicle for difficult riding conditions

Info

Use of the vehicle under difficult conditions, such as on sand or on wet and muddy surfaces, can lead to considerably more

rapid wear of components such as the drive train, brake system, or suspension components. For this reason, it may be neces-

sary to inspect or replace parts before the next scheduled service.

– KTM recommends using the specified engine oil when riding under difficult conditions and to enhance performance.

Engine oil (SAE 10W/60) (00062010035) ( p. 96)

–

Clean the air filter and air filter box. x ( p. 46)

Info

Check the air filter approx. every 30 minutes.

–

Seal the air filter box. x ( p. 47)

–

Secure the air filter box lid. x ( p. 47)

– Additionally secure the rubber grip. ( p. 57)

– Check the electrical connector for humidity and corrosion and to ensure it is firmly seated.

» If humidity, corrosion or damage is found:

– Clean and dry the connector, or change it if necessary.

Difficult riding conditions are:

– Rides on dry sand. ( p. 18)

– Rides on wet sand. ( p. 18)

– Rides on wet and muddy surfaces. ( p. 19)

– Rides at high temperature and slow speed. ( p. 19)

– Rides at low temperatures or in snow. ( p. 19)

7 PREPARING FOR USE 18

7.4 Preparing for rides on dry sand

B00435-01

– Fit a dust cover on the air filter.

Dust protection device for air filter (77206920000)

Info

See the KTM PowerParts fitting instructions.

B00436-01

– Fit a sand cover on the air filter.

Sand protection device for air filter (77206922000)

Info

See the KTM PowerParts fitting instructions.

600868-01

– Clean the chain.

Chain cleaner ( p. 98)

– Fit the steel sprocket.

Tip

Do not grease the chain.

– Clean the radiator fins.

– Straighten bent radiator fins carefully.

7.5 Preparing for rides on wet sand

B00437-01

– Fit a rain cover on the air filter.

Waterproofing device for air filter (77206921000)

Info

See the KTM PowerParts fitting instructions.

600868-01

– Clean the chain.

Chain cleaner ( p. 98)

– Fit the steel sprocket.

Tip

Do not grease the chain.

– Clean the radiator fins.

– Straighten bent radiator fins carefully.

Page is loading ...

KTM 350 SX-F 2014 Owner's manual

This manual is also suitable for

KTM 350 SX-F 2014 Owner's manual

Related papers

Other documents