CAUTION:
DUE TO THE HIGH TEMPERATURE OF LENSES, CARE
SHOULD BE TAKEN IN SELECTION OF INSTALLATION
LOCATIONS TO AVOID THE POSSIBILITY OF CONTACT
WITH BARE SKIN.
12881 Bradley Ave
Sylmar, CA 91342
Phone: 818-362-9465
Fax: 818-362-6548
www.hydrel.com
©2006 Hydrel
Rev. 07/25/06
INS-4400 REV_1
NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT
NOTICE. Any dimension on this sheet is to be assumed as a reference
dimension: "Used for information purposes only. It does not govern
manufacturing or inspection requirements." (ANSI Y14.5-1973)
4400 SERIES
FLUSH MOUNTED UPLIGHTS
INSTALLATION DIAGRAM
LENS DOOR
1. Remove screws—remove lens & gasket.
2. Remove socket yoke assembly.
3. Remove j-box cover hex screws
4. Make electrical connections as required.
5. Push supply wiring and splices back into j-box.
6. Seal conduit entry.
7. Mix potting compound as described on package and fill j-box with mixed compound.
8. Re-install j-box cover with hex screws.
9. Re-install socket yoke assembly
10. Install lamp
11. Aim lamp assembly
12. Re-install lens and gasket.
13. Install door and tighten screws evenly, as shown.
TYPICAL INSTALLATIONS
UF CABLE
CONNECTED
CONDUIT
CONNECTED
ABS WELL
(BY OTHERS)
INSTALL FIXTURE WITH
FINISH GRADE IN EARTH OR
MASONRY ONLY.
USE SUITABLE
THREAD SEALING
COMPOUND WHEN
CONNECTING
CONDUIT.
SUPPLY CONDUIT
SUPPLY
CABLE
LEAVE ENOUGH CABLE TO
REMOVE FIXTURE FOR
MAKING ELECTRICAL
CONNECTIONS.
>
>
>
>
>
>
>
MOST MODELS
HAVE A PROTEC-
TIVE EXTERIOR
COATING OF
BITUMINOUS PAINT
OR EPOXY. SHOULD
THIS FINISH BE
DAMAGED DURING
INSTALLATION,
ANY EXPOSED
SURFACE SHOULD
BE COATED WITH A
SIMILAR
MATERIAL.
TIGHTEN SCREWS
EVENLY USING A
CRISSCROSS PATTERN
TO 50 INCH POUNDS.
(MINIMUM)
NOTE:
USE LAMP WITH
CORRECT ANSI CODE AND
RATED WATTAGE.
INSTALLATION INSTRUCTIONS
Installation should be performed by a qualified
electrician in accordance with the National Electrical Code
and relevant local codes.
12881 Bradley Ave
Sylmar, CA 91342
Phone: 818-362-9465
Fax: 818-362-6548
www.hydrel.com
©2006 Hydrel
Rev. 07/25/06
INS-4400 REV_1
NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT
NOTICE. Any dimension on this sheet is to be assumed as a reference
dimension: "Used for information purposes only. It does not govern
manufacturing or inspection requirements." (ANSI Y14.5-1973)
>
>
>
>
>
>
>
LOWER WATTAGE LAMPS ARE
RECOMMENDED FOR HIGH
PEDESTRIAN TRAFFIC AREAS.
MAINTENANCE TIPS:
1. Clean lens: Debris must be kept clear from top of fixture.
Excessive heat could occur that may harm fixture gasket or
create a fire hazard.
2. Check screw tightness and lens cleanliness on a regular
maintenance schedule.
3. Use a soda straw to blow debris out of screw holes .
4. Lenses may be soaked in white vinegar to remove lime build-
up.
5. Replace gasket if it is cracked, torn, or badly depressed or
worn.
6. If trouble is experienced removing screws, try tapping lightly
with a hammer on the handle of the screwdriver while turning.
1. Remove screws from lamp housing in a crisscross pattern.
2. If moisture is observed, dry lamp compartment thoroughly and
operate lamp to remove moisture prior to closing up fixture.
3. When replacing lamp use correct lamp type and rated
wattage.
4. Check lens gasket for cracks and replace as often as
needed.
5. Remove debris from screw and holes or under gasket or lamp
housing will not seal properly.
6. Install screws and tighten evenly using a crisscross pattern
to 50 inch pounds, (minimum).
RELAMPING:
Use lamp with correct ANSI code
and rated wattage.
If moisture is observed,
dry lamp compartment thoroughly
and operate lamp to remove moisture
prior to closing fixture.
4400 SERIES
FLUSH MOUNTED UPLIGHTS
INSTALLATION INSTRUCTIONS
Installation should be performed by a qualified
electrician in accordance with the National Electrical Code
and relevant local codes.
/
