Leuze ODS 96 M/S Laser Technical And Software Description

Brand: Leuze

Model: ODS 96 M/S Laser

Category: Measuring & layout tools

Type: Technical And Software Description

This manual is also suitable for

Leuzeelectronic

Optical Distance Sensors ODS 96

Technical Description

Software Description

(print, photocopies, microfilm or data) may only be carried out with the expressed written consent of Leuze elec-

tronic GmbH & Co.

We reserve the right to make changes for the technical improvement of the product.

Leuze electronic Contents

Leuze electronic ODS 96 3

1 General Information .......................................................................... 5

1.1 Explanation of Symbols ......................................................................5

1.2 Important Terms .................................................................................. 5

1.3 Declaration of Conformity ................................................................... 6

2 Safety Notices ................................................................................... 6

2.1 Safety Standard .................................................................................. 6

2.2 Intended Use .......................................................................................6

2.3 Working Safely .................................................................................... 7

2.4 Organizing Measures .......................................................................... 7

3 Description ........................................................................................ 8

3.1 General description ............................................................................. 8

3.2 Typical Areas of Application for the ODS 96 ....................................... 8

3.2.1 Continuous Distance Measuring .................................................... 8

3.2.2 Positioning Tasks ...........................................................................9

3.2.3 Filling Level Control for Bulk Goods ............................................... 9

3.3 ODS 96 Models ................................................................................. 10

3.3.1 ODS 96 M/V with Analog Output ................................................. 10

3.3.2 ODS 96 M/D with Serial Output ................................................... 11

3.3.3 ODS 96 M/S with Two Switching Outputs ....................................13

4 Technical Data ................................................................................. 14

4.1 Optical Data ...................................................................................... 14

4.2 LED Indicators .................................................................................. 14

4.3 Electrical Data, Installation Data ....................................................... 15

4.4 Dimensioned and Connection Drawings ........................................... 16

4.5 Accessories ....................................................................................... 17

5 Installation ....................................................................................... 18

5.1 Storage, Transportation ....................................................................18

5.2 Mounting ........................................................................................... 18

5.3 Teach-In ............................................................................................ 19

6 Software ........................................................................................... 20

6.1 Connection of the PC ........................................................................ 20

6.2 Installation of the Programming Software ......................................... 20

6.3 Starting the Program ......................................................................... 21

6.3.1 Description of the Menu Commands ............................................22

6.3.2 Programming and Adjustment Possibilities .................................. 22

7 Appendix .......................................................................................... 27

7.1 How to update the parameter files of the ODS 96 software .............. 27

Contents

4 ODS 96 Leuze electronic

Figures and Tables Leuze electronic

Figure 3.1: Application example "Positioning Tasks" ............................................ 9

Figure 3.2: Application example "Filling Level Control" ....................................... 10

Figure 3.3: Behavior of the analog output, ODS 96 M/V (LED) .......................... 10

Figure 3.4: Behavior of the analog output, ODS 96 M/V (laser) .......................... 11

Figure 3.5: Serial output, ODS 96 M/D ............................................................... 11

Figure 3.6: Behavior of the switching outputs, ODS 96 M/S ............................... 13

Figure 4.1: Dimensioned drawing ODS 96 devices ............................................ 16

Figure 4.2: Electrical connection, ODS 96 M/V ................................................... 16

Figure 4.3: Electrical connection, ODS 96 M/D ................................................... 17

Figure 4.4: Electrical connection, ODS 96 M/S ................................................... 17

Figure 5.1: Preferred movement of the objects ................................................... 18

Figure 5.2: Preferred mounting, objects with structured surface ......................... 19

Figure 5.3: View through a chase ....................................................................... 19

Figure 6.1: Installation directory .......................................................................... 21

Figure 6.2: Device selection ................................................................................ 21

Figure 6.3: Start menu before measurement ...................................................... 22

Figure 6.4: Parameterization mode, ODS 96 with analog output ........................ 23

Figure 6.5: Programming window ODS 96 with two switching outputs ............... 24

Table 1: Optical data, Error limits, Timing ....................................................... 14

Table 2: LED indicators .................................................................................. 14

Table 3: Electrical, Mechanical, and Environmental data ............................... 15

Table 4: Accessories ...................................................................................... 17

Table 5: Regulation values of the sensors ...................................................... 24

Figures and Tables

Leuze electronic General Information

Leuze electronic ODS 96 5

1 General Information

1.1 Explanation of Symbols

The symbols used in this operating manual are explained below.

Attention

This symbol appears in front of text which must be carefully observed. Failure

to heed this information can lead to injuries to personnel or damage to the

equipment.

Attention Laser Radiation

This symbol warns of possible danger through hazardous laser radiation.

Notice

This symbol indicates text which contains important information.

1.2 Important Terms

Triangulation

Distance measuring procedure, which determines the distance of an object

by the incidence angle of the light reflected from the object.

Absolute measurement

accuracy

Shows the possible divergence of the measurement value from the anticipat-

ed value through changes in the environmental conditions during the mea-

suring process. Higher accuracy is given at constant environmental condi-

tions.

Repeatability

Measuring distance change with repeated measurement at the same output

signal (observe the same peripheral conditions as with resolution).

Resolution

The smallest possible distance change of the measured object, which causes

a definite change in the output signal. Resolution is higher in the proximate

area than in the distant area. Small objects can be recognized better in the

proximate area.

Remission

Return and/or degree of reflection of the radiated light.

Integration time

The integration time of the ODS 96 is comparable to the exposure time in a

camera. It is automatically adjusted to the intensity of the reflected light and

thus depends on the reflectance factor of the measured object. It is inversely

proportional to the measurement frequency.

Measurement

frequency

The measurement frequency represents the number of measurements per

second. When adjusting the integration time to the reflectivity independency,

the measurement frequency changes corresponding to the reflectivity value.

Response time

The time period required by the ODS to obtain stable measurements after

change of the reflectivity behavior.

Delay before

start-up

The delay before start-up indicates the point in time when the first valid mea-

surement can be obtained after switching on.

Safety Notices Leuze electronic

6 ODS 96 Leuze electronic

Light switching/

Dark switching

Indicates the behavior of the switching output when an object is inside the

tought/parametered switching distance. At light switching, the switching out-

put is active (high), at dark switching inactive.

Insensitivity towards

extraneous light

Indicates the insensitivity of the measurement result towards extraneous

light. The ODS 96 is reliably measuring even with extraneous light intensity

of 5 kLux. Typical light intensity in a work place is only 1 kLux.

1.3 Declaration of Conformity

The optical distance sensors of the series ODS 96 have been manufactured

observing current European standards and guidelines.

Notice

The corresponding declaration of conformity can be requested from the

manufacturer.

The manufacturer of the product, Leuze electronic GmbH & Co. in D-73277

Owen/Teck, possesses a certified quality assurance system in accordance

with ISO 9001.

2 Safety Notices

2.1 Safety Standard

The optical distance sensors of the series ODS 96 have been developped,

manufactured and tested, observing current safety standards. They corre-

spond to the state of the art.

2.2 Intended Use

Attention

The protection of personnel and the device cannot be guaranteed if the de-

vice is operated in a manner not corresponding to its intended use.

Optical distance sensors of the series ODS 96 are intelligent, adjustable sen-

sors with CCD element for distance measuring.

In particular, unauthorized uses include:

•rooms with explosive atmospheres (zone 0, 1). Operation in zone 2 is

possible with a manufacturer's declaration.

•operation for medical purposes

Leuze electronic Safety Notices

Leuze electronic ODS 96 7

Fields of application

The optical distance sensors of the series ODS 96 have been designed for

the following areas of application:

•Distance measurement

•Contour determination

•Stack positioning

•Filling level measurement

•Packet conveying machines and many more

2.3 Working Safely

Attention Laser Radiation

The ODS 96 M/D, V, S ... are laser devices of the Laser Protection Class 2.

Do not look directly into the laser beam.

Observe the applicable legal and local regulations for the operation of laser

units.

Attention

Access to or making changes to the device, except where positively de-

scribed in this operating manual, is not authorized.

2.4 Organizing Measures

Documentation

All entries in this operating manual must be heeded, in particular those in sec-

tion 2 "Safety Notices".

Carefully store this operating manual where it is accessible at all times.

Safety regulations

Observe the locally applicable legal regulations and the rules of the employ-

er's liability insurance association.

Qualified personnel

Mounting, commissioning and maintenance of the device may only be carried

out by qualified personnel.

Electrical work must be carried out by a certified electrician.

Repair

Repairs must only be carried out by the manufacturer or an authorized rep-

resentative.

Description Leuze electronic

8 ODS 96 Leuze electronic

3 Description

3.1 General description

The ODS 96 is a distance measuring device with a large area of application.

The equipment is available as LED or laser version with analog or digital out-

puts. The distance measuring device works on the triangulation principle and

uses a CCD line for evaluating the measurement signal.

An integrated microcontroller enables parameter programming via an option-

al programming software. Except for the RS 485 interface, the switching

points of the switching outputs of all other types can be set without software

via a teach-in input.

Through adjustment of the integration time (exposure time) to the intensity of

the objects’ reflected light, a high degree of independence from the reflectivity

properties of the measured object is achieved. In case of low reflectivity (dark

objects) a lower measurement frequency results.

Accessories

To expand the functionality of the ODS 96, a programming software is avail-

able.

With regard to their dimensions, the ODS 96 distance sensors are identical

with the sensors of the series 96 of Leuze electronic. Particularly, the mount-

ing accessories of the series 96 can be used for the ODS 96. Details can be

found in section 4 "Technical Data".

3.2 Typical Areas of Application for the ODS 96

3.2.1 Continuous Distance Measuring

All ODS 96 types with analog or digital output can be used for continuous dis-

tance measuring. In order to use all features of the ODS 96, use of the pro-

gramming software is recommended.

Depending on position or settings of the ODS, various applications are pos-

sible:

•Measuring the thickness of planks with two opposing sensors and a dif-

ferential of the two measured values.

•Stack/Object height measuring

Even with difficult surfaces, the stack/ object height of moving objects

can be measured. Averaging is recommended here.

•Contour determination through controlled passing movement of an

object through the beam of the ODS 96.

•Volume measuring by taking measurements on two levels during the

concurrent movement of the object. Leuze electronic offers a system

solution: the VMS volume measurement system.

In case of ODS 96 types with analog outputs, it is recommended to limit the

working range of the analog output to the required distance range. The ana-

log output will then be activated within the distance range from 1 ... 10 V or

4 - 20 mA. Distances outside this range will automatically have an output

voltage of < 1 V, 4 mA or > 10 V, 20 mA.

Leuze electronic Description

Leuze electronic ODS 96 9

3.2.2 Positioning Tasks

For simple positioning tasks, all ODS 96 M/S types with two teachable

switching outputs are suitable.

The ODS 96 is mounted in a way to enable positioning in the direction of the

measuring beam. Both switching outputs are tought to the required position.

In case the distance is smaller than the tought position, switching output 1 is

active and switches the positioning motor to enlarge the distance. In case the

distance is bigger than the tought position, switching output 2 is active and

switches the positioning motor to reduce the distance.

Using this method, positioning tasks can be performed without difficulties.

Figure 3.1: Application example "Positioning Tasks"

3.2.3 Filling Level Control for Bulk Goods

For the filling level control in connection with control of material flow, all ODS

96 types with one switching output are suitable. However, the programming

software is required to adjust the hysteresis.

The ODS 96 is mounted ensuring that its measuring beam meets the surface

of the bulk good vertically. Using the software, function of Q1 is set to "light

switching" and the minimal filling level entered as lower limit. The upper limit

is set to the maximum range of the ODS (600 mm or 2000 mm, depending on

the ODS type). The distance between minimum and maximum filling level is

entered as hysteresis.

Old Stack

New Stack

Positioning

Description Leuze electronic

10 ODS 96 Leuze electronic

Material flow is switched on/off by the ODS as soon as the filling level falls

below the lower limit or reaches the maximum.

Figure 3.2: Application example "Filling Level Control"

Notice

For mounting instructions please refer to section 5.2 "Mounting".

3.3 ODS 96 Models

Types

Two different types of the ODS 96 are available:

•Infrared distance sensor

Measurement range 100 - 600 mm

•Laser distance sensor with visible red light

Measurement range 200 - 2000 mm

3.3.1 ODS 96 M/V with Analog Output

Analog output of the

LED device

Figure 3.3: Behavior of the analog output, ODS 96 M/V (LED)

I (mA) U (V)

app.21 app.10,5

20 10

4 1

1 0

0 90 100 600 app.625 app.800 - 1500

Meas. distance

(mm)

undefined

Linearity

undefined

Measurement range

Linearity

undefined

Object

present

Range

no object

detected

Leuze electronic Description

Leuze electronic ODS 96 11

Analog output of the

laser device

Figure 3.4: Behavior of the analog output, ODS 96 M/V (laser)

Behavior of the output,

ODS 96 M/V

The ODS 96 M/V has an analog output with linear behavior inside the respec-

tive measurement range. The user can choose between current output

(4 - 20 mA) and voltage output (1 - 10 V). Above and below the linear range,

linearity is lost however, the output values signify an upper deviation (>

20 mA respectively > 10 V) or a lower deviation (< 4 mA respectively < 1 V)

of the measurement range.

Additionally, a switching output is available with the ODS 96 M/V. The posi-

tion within the measuring range, at which the switching output is active can

be set as needed via a teach-in lead. The breadth of the active range is

± 2 mm (LED) respectively ± 10 mm (laser).

Using the optional programming software, the declivity of the output charac-

teristic curve can be changed (steep progression with concurrent reduction

of the measurement range). Furthermore, the switching behavior of the addi-

tional switching output can be individually set.

3.3.2 ODS 96 M/D with Serial Output

Serial output of the LED

and laser device

Figure 3.5: Serial output, ODS 96 M/D

Serial output of the

ODS 96 M/D

The serial output of the ODS 96 M/D delivers a continuous data stream. The

measurement value is transmitted with two byte. The LSB signifies the High-

and the Low-Byte, to ensure recognition of definite coherence. For transmis-

sion, no telegram frame, but only the normal serial protocol is used. The

transmission protocol consists of 8 databit, 1 startbit, 1 stopbit, no parity. The

I (mA) U (V)

app.21 app.10,5

20 10

4 1

1 0

0 180 200 2000 2100 app.3000

Meas. distance

(mm)

undefined

Linearity

undefined

Measurement range

Linearity

undefined

Object

present

Range

no object

detected

Measurement value = 14 Bit

1. Low-Byte (Bit 0 = 0) 2. High-Byte (Bit 0 = 1)

LSB MSB

Description Leuze electronic

12 ODS 96 Leuze electronic

ODS 96 M/D has a digital output which is realized either through the RS 232

or the RS 485 interface. The transmission rate is 9600 baud at the RS 232

interface and 9600 baud without termination at the RS 485 interface.

A "C" program example demonstrates how bytes are read and processed for

further usage:

Program example in "C"

//Start of the program for measurement value generation-------------------------------

Rxbyte = inportb(RXB(COM2.port_adr)); //Read transmitted byte

if (flag==0) //First byte has to be a

//Low-Byte

{

if ((Rxbyte & 0x01) == 0) //Test on Low-Byte

{

value = (Rxbyte & 0xFE) >> 1; //Insert measurement value

//point-aligned

flag = 1; //Next received

//byte has to be a

//High-Byte

}

else

{

if ((Rxbyte & 0x01) == 1) //Test on High-Byte

{

value|=((Rxbyte&0xFE) << 6); //Insert point-aligned in

//measurement value

flag = 0; //14 Bit measurement value

//is generated

measurement value = value; //Save measurement value

}

// End of program of measurement value generation--------------------------------------

The behavior of the switching output of the ODS M/D can be set as described

with the ODS 96 M/V. However, the ODS 96 M/D type with RS 485 interface

does not offer a teach input.

Leuze electronic Description

Leuze electronic ODS 96 13

3.3.3 ODS 96 M/S with Two Switching Outputs

Switching outputs of

the LED and laser

device

Figure 3.6: Behavior of the switching outputs, ODS 96 M/S

ODS 96 M/S with two

switching outputs

The two switching outputs of the ODS 96 M/S are working independently

from each other. Through the teach input, the second signal edge can be

tought at output 1, the first signal edge is situated at the beginning of the mea-

surement range. The first signal edge can be tought at output 2, the second

signal edge is situated at the end of the measurement range.

A teach line is available for both switching outputs, meaning the switching

outputs are tought alternatingly. The presently tought output is displayed

through the simultaneous or alternating flashing of the LEDs.

The outputs can be adjusted independently of each other by using the option-

al programming software.

+UB

2. switching output

1. switching output

LED: 100 600

Laser: (200) (2000)

Measuring distance

(mm)

Technical Data Leuze electronic

14 ODS 96 Leuze electronic

4 Technical Data

4.1 Optical Data

4.2 LED Indicators

ODS 96

M/V, M/D, M/S ODS 96

M/V, M/D, M/S Laser

Optical data

Measurement range 1

1.Reflectance factor 6%...90%, over the whole temperature range, measured object



50x50 mm

100-600 mm 200-2000 mm

Resolution  0,5 mm  5 mm

Light source LED (modulated light) Laser (modulated light)

Wavelength 880 nm (infrared) 660 nm (visible redlight)

Light-spot diameter approx. 10 mm (over whole

measuring range) divergent min. 3x12 mm in

2000 mm distance

Error limits

Absolute measure-

ment accuracy 1± 2% ± 2%

Repeatability 2

2.Same object, measured object



50x50 mm

± 0,5% ± 0,5%

b/w detection thresh-

olds (6%/90%)  1%  1%

Timing

Switching frequency 20-100 Hz 10-100 Hz

Response time  100 ms

Delay before start-up  300 ms

Table 1: Optical data, Error limits, Timing

LED ODS 96 M/V, M/V Laser;

ODS 96 M/D, M/D Laser ODS M/S, M/S Laser

teach-in on GND teach-in on +UBteach-in on GND teach-in on +UB

permanent

green light Device Ready Device Ready

flashing green Error Teach-in proce-

dure1

1.The teach-in process is described in detail in section 5.3 "Teach-In"

Error Teach-in

procedure1

green off no voltage no voltage

yellow perma-

nent light

Object inside

teach-in measure-

ment distance

Object inside

measurement

range

yellow flash-

ing Teach-in

procedure1

Object outside

measurement

range

Teach-in

procedure1

yellow off Object outside

teach-in measure-

ment distance

no object

detected

Table 2: LED indicators

Leuze electronic Technical Data

Leuze electronic ODS 96 15

4.3 Electrical Data, Installation Data

M/V; M/V Laser M/D; M/D Laser M/S; M/S Laser

Electrical data

Operating voltage UB 18...30 V DC (incl.

residual ripple) 10...30 V DC (incl. residual ripple)

Residual ripple  15% of UB

Bias current  150 mA

Switching outputs 1

Inversion possible through programming software

PNP transistor, high-active 2 PNP transistor out-

puts, high active

Signal voltage high/low  (UB - 2V) /  2V

Analog output

RL  2 kOhm

(Voltage)

1…10 V

RL  500 Ohm

(Current)

4…20 mA

Output current max. 100 mA per

transistor output

Digital output RS 232 9600 Baud

RS 485 9600 Baud, no ter-

mination

Transmission protocol 2 Byte transm.,

cont. data stream

Mechanical data

Housing Diecast zinc

Optical cover Glass

Weight 380g

Connection type Terminals or M 12 dia. connectors

Environmental data

Ambient temp. (opera-

tion./storage) -20°C..+50°C / -30°C..+70°C

Extraneous light limit  5 kLux

Protective circuit 2

1=transient protection, 2= polarity reversal protection, 3= short circuit protection for all outputs

1,2,3

VDE safety class 3

Rating voltage 250 V AC

II, all-insulated

Protection class IP 67

Impact resistance Semi-sinusoidal, 30 gn, 11 ms (VDE 0660T208)

Vibration resistance 10-55 Hz, max. 7,5 gn (VDE 0660T208)

Electromagnetic compatibil-

ity Severity level 3 (IEC 60947-5-2)

Table 3: Electrical, Mechanical, and Environmental data

Technical Data Leuze electronic

16 ODS 96 Leuze electronic

4.4 Dimensioned and Connection Drawings

All ODS 96 devices

Figure 4.1: Dimensioned drawing ODS 96 devices

ODS96 M/V

Figure 4.2: Electrical connection, ODS 96 M/V

green yellow

Indicator LEDs

optical axis

Device Plug

Cable Screwing PG 11 for dia. 5-10 mm

Parameter Plug

Connection Terminals

Cable lead-in

Countersinking for

SK nut M5, 4.2 deep

Leuze electronic Technical Data

Leuze electronic ODS 96 17

ODS 96 M/D

Figure 4.3: Electrical connection, ODS 96 M/D

ODS 96 M/S

Figure 4.4: Electrical connection, ODS 96 M/S

4.5 Accessories

The following accessories are available for the ODS 96:

Designation Order No. Short Description

KB-ODS96-1500 50082007 Parameterizing cable 1,5 m

KB-ODS96-6000 50061428 Parameterizing cable 6 m

ODS96-PS 50082006 Programming software

KB-095-5000-5 50020500 Connection lead (M12, angled, 5 m)

KB-095-5000-5A 50020499 Connection lead (M12, axial, 5 m)

BT 96 50025570 Mounting part

UMS 96 50026204 Universal mounting system

Table 4: Accessories

Installation Leuze electronic

18 ODS 96 Leuze electronic

5 Installation

5.1 Storage, Transportation

Unpacking

Check the packaging for any damage. If damage is found, notify the post

office or shipping agent as well as the supplier.

Check the delivery contents using your order and the delivery papers:

•delivered quantity

•device type and model as indicated on the name-plate

•accessories

•operating manual

Save the original packaging for later storage or shipping.

If you have any questions concerning your shipment, please contact your

supplier or your local Leuze electronic sales office.

Observe the applicable local regulations when disposing of the packaging

materials.

5.2 Mounting

Mounting systems are available which have to be ordered separately at

Leuze electronic. For order numbers please refer to section 4.5 "Accesso-

ries". Apart from this, the through-borings can be used for individual mounting

of the ODS 96, depending on the area of application.

Mounting of the ODS 96

To avoid errors while the object enters the measurement beam, correct

movement direction of the objects has to be observed. The following graphics

show instructions on the installation of the ODS 96:

Preferred movement of

the objects

Figure 5.1: Preferred movement of the objects

Leuze electronic Installation

Leuze electronic ODS 96 19

Preferred mounting in

connection to objects

with structured surface

Figure 5.2: Preferred mounting, objects with structured surface

View through a chase

Figure 5.3: View through a chase

If the ODS 96 has to be installed behind a cover, the chase has to have at

least the size of the optical glass cover. Otherwise, a correct measurement is

not possible or can not be guaranteed.

5.3 Teach-In

Notice

The teach-in procedure can be extended and facilitated through the optional

programming software.

Switching points can also be set through teach-in without using the software.

Connected to the teach-in procedure, differences occur between the ODS 96

M/S types with two switching outputs and the analog and digital device:

Teach-In procedure

ODS 96 M/V, ODS 96

M/D

Position the measured object at the desired distance. Connect the teach

input for



sec. to +U

. After that, connect the teach input to GND. The

switching output is tought.

The tought switching point represents the middle of the switching range of the

output.

These default values are preset:

•Function characteristics of the switching output: "light switching"

•Switching range: ± 2 mm with infrared devices and ± 10 mm with laser

devices

•Hysteresis: ± 1 mm with infrared devices and ± 5 mm with laser devices

These values can only be changed by using the programming software.

Software Leuze electronic

20 ODS 96 Leuze electronic

Teach-In procedure

ODS 96 M/S

Position the measured object at the first desired distance. Connect the

teach input for



sec. to +U

. The LEDs are flashing simultaneously. Re-

connect the teach input to GND. The first switching output is tought. Now,

position the measured object at the second desired distance. Connect the

teach input for



sec to +U

. The LEDs are flashing alternatingly. Recon-

nect the teach input to GND. The second switching output is tought. In

non-operational mode, the teach input is connected to GND.

6 Software

General description

The programming software can be used either for online programming of the

connected ODS 96 or for the offline generation of configurations. For this pur-

pose, the command Type!, explained in section 6.3.1 "Description of the

Menu Commands" can be used. After starting the program a dialog is dis-

played in which you have to choose a device (see section 6.3 "Starting the

Program"). After the offline generation of a parameter configuration, this con-

figuration can be transmitted to the ODS 96 after connection to the PC has

been established.

The order number for the software can be found in section 4.5 "Accessories".

6.1 Connection of the PC

A special parameter plug is situated behind the plastic cover on the backside

of the ODS 96. Connection between the ODS 96 and the PC is established

by means of the cable included in the shipment.

Connect the cable to the parameter plug on the ODS 96 and to a serial

interface on the PC. More information on the definition of the interface can

be found in section 6.3.1 "Description of the Menu Commands".

6.2 Installation of the Programming Software

Requirements for the installation of the programming software:

•Windows 3.1 or Windows 95/98/NT,

•486 processor or faster,

•4 MByte RAM,

•2 MByte free disk space

•and a CD-Rom drive.

Page is loading ...

Leuze ODS 96 M/S Laser Technical And Software Description

Brand: Leuze

Model: ODS 96 M/S Laser

Category: Measuring & layout tools

Type: Technical And Software Description

This manual is also suitable for

Download PDF

report

Leuze ODS 96 M/S Laser Technical And Software Description

This manual is also suitable for

Leuze ODS 96 M/S Laser Technical And Software Description

Related papers

Other documents