Page is loading ...
9'-9
15
16
" [300 cm]
6'-9" [206 cm]
10'-11
1
4" [333 cm]
11'-6
7
8
" [353 cm]
9'-7
1
4" [293 cm]
INSTRUCTIONS
0096_Tuscany_11x11_Instructions_V1.2
TUSCANY
CODE: 0096
TOLL FREE/SANS FRAIS: 1-877-795-7423
EN
Front Elevation
Footprint Plan
LADDER (8ft / 2.5m)
RUBBER MALLET
POWER DRILL
TAPE MEASURE
PENCIL
IMPORTANT
0096_Tuscany_11x11_Instructions_V1.2
TUSCANY
CODE: 0096
TOLL FREE/SANS FRAIS: 1-877-795-7423
TOOLS NEEDED
TWO PERSON PROJECT
PRODUCT CAN BE HEAVY
USE CARE WHEN LIFTING
SITE PREPARATION
ASSEMBLE THE STRUCTURE ON A FIRM, LEVEL SURFACE.
PROTECT THE PRODUCT FROM DAMAGE AS SOME PIECES MAY BE FRAGILE.
ESTIMATED ASSEMBLY TIME: 4 HOURS
IF YOU REQUIRE ASSISTANCE, OR NEED TO ORDER REPLACEMENT PARTS,
CONTACT YOUR VISSCHER DEALER.
FOR ADDITIONAL INFORMATION PLEASE CALL THE NUMBER BELOW.
PLEASE HAVE SERIAL NUMBER READY TO ENSURE QUICK SERVICE.
BEFORE YOU BEGIN
THESE INSTRUCTIONS MUST BE FOLLOWED STEP BY STEP. DEVIATION FROM THE
INSTRUCTIONS MAY VOID THE PRODUCT'S WARRANTY. SEE WARRANTY SHEET
FOR FURTHER DETAILS.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING ASSEMBLY.
USE THE PARTS LIST AS A CHECKLIST FOR COMPONENTS.
UNWRAP PARTS ONLY AS NEEDED TO KEEP COMPONENT DEALER CODE LABEL
INTACT FOR REFERENCE.
EN
1037
1305
1041
1304
2X
4X
4X
4X
1070
4X
1961
8X
1960
4X
1056
4X
8'-5"
4'-3"
7'-2"
1'-4"
2'-6"
2'-10"
10'-7"
6'-11"
6'-11"
1677
4X
1678
4X
1754
4X
1244
4X
1465
4X
1324
4X
1325
4X
1459
1X
1170
1X
8X
1824
12X
1825
7'-10"
3'-9"
5'-2"
5'-2"
7'-11"
6'-2"
8'-4"
2029
1X
2029
1X
1868
4X
1866
4X
1867 1869
4X 4X
6'-4"
6'-4"
3'-10"
3'-10"
0096_Tuscany_11x11_Instructions_V1.2
TUSCANY
CODE: 0095
PAGE
OF
DE
TOLL FREE: 1-877-795-7423
TRUSS FRAME / FERME DE TOIT
ROOFING / TOITURE
EN
1077
1X
1061
2X
1097
1X
1095
1X
1096
1X
3'-0"
3'-0"
3'-0"
1'-8"
10'-0"
3X
6X
6X
6X
1990
1993
1992
1991
1'-5"
2'-6"
7"
10"
0096_Tuscany_11x11_Instructions_V1.2
TUSCANY
CODE: 0095
PAGE
OF
DE
TOLL FREE: 1-877-795-7423
BAR
STOOLS / TABOURETS
EN
INSTRUCTION MANUAL /
MANUEL D'INSTRUCTION
1X
1X
1X
ROBERTSON BIT/
EMBOUT ROBERTSON
1/4" HEX HEAD BIT/
EMBOUT A TETE
HEXAGONALE DE 1/4 PO
12X
1965
1X
2033
HARDWARE - QUINCAILLERIE
0096_Tuscany_11x11_Instructions_V1.2
TUSCANY
CODE: 0096
TOLL FREE/SANS FRAIS: 1-877-795-7423
B
2 1/2" #8 FLAT HEAD (#2 ROBERTSON)
315X
M
3" SCREW #8 HEX HEAD (1/4" DRIVER)
20X
A
1 1/2" #8 FLAT HEAD (#2 ROBERTSON)
30X
1 1/2 PO TETE PLATE NO 8 (no 2 ROBERTSON)
F
2 1/2" #8 PAN HEAD (#2 ROBERTSON)
25X
E
75X
1 1/4 PO TETE TRONCONIQUE no 8
1 1/4" BLACK ROBERTSON SCREWS
I
1" #10 METAL ROOF SCREW (1/4" HEAD)
155X
EN
Step One
TUSCANY
BEGIN ASSEMBLY BY SCREWING THE FOUR TRUSS FRAME (DEALER CODE 1305)
PIECES TOGETHER AS SHOWN. ATTACH THE PIECES USING THREE 2 1/2" ROBERTSON
SCREWS AS EACH JOINT AS SHOWN.
2 1/2" ROBERTSON SCREWS 12 req
NOTE:
IT IS VERY IMPORTANT TO CHASE/FOLLOW CORNERS AS
SHOWN IN DIAGRAMS.
B
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
DC-1305
DC-1305
DC-1305
DC-1305
EN
Step Two
TUSCANY
DC-1304
DC-1304
DC-1304
DC-1304
2 1/2" ROBERTSON SCREWS 16 req
B
MEASURE TRUSS FRAME FROM CORNER TO CORNER TO SQUARE THE FRAME
BEFORE ATTACHING THE SUPPORTS. MEASURE FROM POINT A TO POINT D THAT
MEASUREMENT SHOULD EQUAL POINT B TO POINT C. ADJUST FRAME UNTIL THEY DO.
A TO D = B TO C
ONCE YOU HAVE SQUARED THE TRUSS FRAME ATTACH THE 34" TRUSS FRAME
SUPPORTS (DEALER CODE 1304) TO HOLD THE TRUSS FRAME ASSEMBLY SQUARE AS
SHOWN BELOW. ATTACH EACH PIECE WITH FOUR 2 1/2" SCREWS THROUGH THE
OUTSIDE OF THE TRUSS FRAME INTO THE END OF THE TRUSS FRAME SUPPORT.
ATTACH THE SUPPORT PIECES FLUSH TO THE TOP EDGE OF THE TRUSS FRAME AS
SHOWN BELOW.
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
1
2
Step Three
TUSCANY
CORNER DETAIL
DC-1041
DC-1305
DC-1041
ATTACH THE POSTS TO THE CORNER OF THE
TRUSS FRAME WITH FOUR 2 1/2" ROBERTSON
SCREWS THROUGH THE INSIDE INTO THE TRUSS
FRAME AS SHOWN IN CORNER DETAIL
LIFT UP ONE SIDE OF THE TRUSS FRAME ASSEMBLY AS THE SECOND PERSON SLIDES
A POST (DEALER CODE 1041) UNDER ONE CORNER OF THE OF TRUSS FRAME.
SLIDE THE TRUSS FRAME INTO THE SADDLE OF THE POST AS SHOWN, REST THE
POSTS ON THE GROUND WITH THE OTHER SIDE OF THE TRUSS FRAME ASSEMBLY ON
THE GROUND. ATTACH THE POST TO THE TRUSS FRAME AS DESCRIBED IN THE
CORNER DETAIL DRAWING.
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
2 1/2" ROBERTSON SCREWS 8 req
B
EN
1
Step Four
TUSCANY
CORNER DETAIL
DC-1041
ATTACH THE POSTS TO THE CORNER OF THE
TRUSS FRAME WITH FOUR 2 1/2" ROBERTSON
SCREWS THROUGH THE INSIDE SUPPORT INTO
THE TRUSS FRAME AS SHOWN IN CORNER
DETAIL
LIFT UP THE SECOND SIDE OF THE TRUSS FRAME ASSEMBLY AS THE SECOND
PERSON ATTACHES THE TWO REMAINING POSTS TO THE CORNERS OF THE TRUSS
FRAME.
SLIDE THE TRUSS FRAME INTO THE SADDLE OF THE POSTS AS SHOWN, AND ATTACH
TO THE TRUSS FRAME AS DESCRIBED IN THE CORNER DETAIL DRAWING.
2 1/2" ROBERTSON SCREWS 8 req
B
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
Step Five
TUSCANY
2 1/2" ROBERTSON SCREWS 52 req
SCREW A 2*3 FILLER PIECE (DEALER CODE 1961) TO EACH SIDE OF THE LOUVER
PANEL (DEALER CODE 1037) TOGETHER WITH 2 1/2" SCREWS. WHEN ATTACHING
ENSURE THAT THE 2*3 IS FLUSH WITH THE TOP OF THE 2*4 ON FLAT AND FLUSH WITH
THE OUTSIDE SURFACE OF THE LOUVER AS SHOWN BELOW.
ATTACH THE BRACKETS BELOW THE LOUVER PANELS AGAINST THE SIDE PANELS
WITH FOUR 2 1/2" SCREWS PER BRACKET.
BUILD 2 OF THE THESE ASSEMBLIES.
ATTACH THE 2*8 FILLER (DEALER CODE 1960) TO THE 2*3 FILLER (DEALER CODE 1961)
USING SEVEN 2 1/2" SCREWS AS SHOWN BELOW. WHEN ASSEMBLING ENSURE THAT
EDGES ARE FLUSH ON TOP AND ON FRONT.
NOTE:
BUILD FOUR ASSEMBLIES.
B
DC-1961
DC-1961
DC-1961
DC-1960
DC-1037
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
Step Six
TUSCANY
2 1/2" ROBERTSON SCREWS 40 req
ATTACH THE FILLER PIECE BUILT IN THE PREVIOUS STEP TO THE LOUVER PANEL
ASSEMBLY USING SIX 2 1/2" SCREWS AS SHOWN BELOW. ENSURE THAT ALL EDGES
ARE FLUSH WITH EACH OTHER.
SCREW THROUGH THE FILLER PIECE INTO THE LOUVER PANEL ASSEMBLY AS SHOWN
IN THE DETAIL.
ATTACH LOUVER PANEL BRACE
(DEALER CODE 1056) TO LOUVER
PANEL USING FOUR 2 1/2" SCREWS AS
SHOWN BELOW.
B
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
DC-1056
DC-1056
DC-1056
NOTE:
REPEAT THIS STEP FOR THE SECOND
LOUVER ASSEMBLY.
EN
DC - 1037
TRUSS FRAME
Step Seven
TUSCANY
PLACE THE LOUVER PANEL ASSEMBLIES INSIDE THE STUCTURE BETWEEN THE
POSTS. PLACE THE PANELS SO THAT THEY ARE FLUSH AGAINST THE POST.
ADJUST THE POSTS SO THAT THEY ARE PARALLEL WITH THE PANELS.
ATTACH THE TOP OF THE PANELS TO THE TRUSS FRAME WITH EIGHT 2 1/2"
ROBERTSON SCREWS THROUGH THE TOP 2x2 OF THE LOUVER PANEL INTO THE
TRUSS FRAME AS SHOWN IN DETAIL1.
REPEAT THIS STEP FOR THE SECOND LOUVER PANEL ASSEMBLY
DETAIL 1
2 1/2" ROBERTSON SCREWS 16 req
B
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
1'-0"
1'-0"
Step Eight
TUSCANY
DC 1965
DC 1965
E
1 1/4" BLACK ROBERTSON SCREWS 72 req
PLACE THE TOP MENDING PLATE 1'-0" FROM THE UNDERSIDE OF THE
TRUSS FRAME TO THE MIDDLE OF THE MENDING PLATE AS SHOWN IN
DETAIL 1.
PLACE THE BOTTOM MENDING PLATE 1'-0" FROM THE BOTTOM OF THE
LOUVER PANEL TO THE MIDDLE OF THE MENDING PLATE AS SHOWN IN
DETAIL 2.
DETAIL - 1
DETAIL - 2
ATTACH THE LOUVER PANELS TO THE POSTS USING THREE MENDING PLATES
(DEALER CODE 1965) WITH SIX BLACK 3/4" SCREWS THROUGH THE LOUVER PANEL
INTO THE POST. MAKE SURE THAT THE OUTSIDE EDGE OF THE LOUVER PANEL
ASSEMBLY IS TIGHT TO THE POST BEFORE FASTENING TOGETHER.
REPEAT THIS STEP FOR THE SECOND LOUVER ASSEMBLY
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
Step Nine
TUSCANY
DC-1070
DC-1070
ATTACH THE CORNER BRACKETS (DEALER CODE 1070) INTO THE CORNERS OF THE
OPEN SIDES. PLACE UP AGAINST THE POST AND FLUSH UNDERNEATH THE TRUSS
FRAME. ATTACH THE CORNER BRACKETS WITH FOUR 2 1/2" SCREWS EACH.
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
2 1/2" ROBERTSON SCREWS 16 req
B
EN
Step Ten
TUSCANY
DC-1170
DC-1170
DC-1824
DC-1824
DC-1170
TOP VIEW
DC-1824 X 8
FLUSH
SERIAL NUMBER
TAG
ATTACH EIGHT METAL BRACKETS (DEALER CODE 1824) TO THE OCTAGON PEAK
SUPPORT (DEALER CODE 1170) USING 1 1/2" SCREWS. SCREW THROUGH THE
PRE-DRILLED HOLES IN THE BRACKET INTO THE OCTAGON PEAK SUPPORT.
1 1/2" ROBERTSON SCREWS 16 req
A
0096_Tuscany_11x11_Instructions_V1.2
TOLL FREE: 1-877-795-7423
EN
/
