Kistler 5343B Owner's manual

Instruction

Manual

5343A_002-793e-01.18

DTI-Logger

data acquisition

system

Type 5343A

with KiCenter

Page 15343A_002-793e-01.18

Thank you for choosing a Kistler quality product charac-

terized by technical innovation, precision and long life.

Information in this document is subject to change without

notice. Kistler reserves the right to change or improve its

products and make changes in the content without obliga-

tion to notify any person or organization of such changes

or improvements.

as expressly provided herein, no part of this manual may

be reproduced for any purpose without the express prior

written consent of Kistler Group.

Kistler Group

Eulachstrasse 22

8408 Winterthur

Switzerland

Tel. +41 52 224 11 11

Fax +41 52 224 14 14

info@kistler.com

Kistler Instrumente GmbH

Division Automotive Research & Test

Charlotte-Bamberg-Str. 12

35578 Wetzlar

Germany

Tel. +49 6441 9282 0

Fax +49 6441 9282 17

info.de@kistler.com

www.kistler.com

Foreword

Kistler Group products are protected by several intellectual property rights

patents. For more details see: www.kistler.com

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 2

1. Introduction .................................................................................................................................3

2. Important Notes...........................................................................................................................4

2.1 For Your Safety ...................................................................................................................4

2.2 Glossary .............................................................................................................................6

2.3 Disposal Instructions for Electrical and Electronic Equipment ............................................6

2.4 Software Upgrades and Updates .......................................................................................6

3. Product description ....................................................................................................................7

3.1 In General ...........................................................................................................................7

3.2 Application ..........................................................................................................................8

3.3 Accessories ........................................................................................................................8

4. Technical Data .............................................................................................................................9

4.1 Specications .....................................................................................................................9

4.2 DTI-Logger Pin Assignments / Ports and Slots ................................................................10

4.3 DTI-Logger Status LEDs ..................................................................................................14

5. Software ....................................................................................................................................15

5.1 Toolbar ..............................................................................................................................15

5.1.1 Explanation of the Buttons in the Toolbar ............................................................16

5.1.2 Tools ....................................................................................................................17

5.2 Breaking Distance Application Example ...........................................................................18

5.2.1 Device Center ......................................................................................................19

5.2.2 Test Center ..........................................................................................................23

6. Troubleshooting ........................................................................................................................48

6.1 LEDs .................................................................................................................................48

7. Appendix ....................................................................................................................................49

Total number of pages: 49

Contents

Introduction

Page 35343A_002-793e-01.18

1. Introduction

Take the time to thoroughly read this instruction manual.

It will help you with the installation, maintenance, and use

of this product.

To the extent permitted by law Kistler does not accept any

liability if this instruction manual is not followed or products

other than those listed under Accessories are used.

Kistler offers a wide range of products for use in measuring

technology:

Piezoelectric sensors for measuring force, torque,

strain, pressure, acceleration, shock, vibration and

acoustic-emission

Strain gage sensor systems for measuring force and

torque

Piezoresistive pressure sensors and transmitters

Signal conditioners, indicators and calibrators

Electronic control and monitoring systems as well as

softwareforspecicmeasurementapplications

Data transmission modules (telemetry)

Kistler also develops and produces measuring solutions

for the application elds engines, vehicles, manufac-

turing, plastics and biomechanics sectors.

Our product and application brochures will provide you

with an overview of our product range. Detailed data

sheets are available for almost all products.

If you need additional help beyond what can be found

either on-line or in this manual, please contact Kistler's

extensive support organization.

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 4

2. Important notes

2.1 For your safety

Read this carefully before operating the equipment. Kistler

is not responsible for damage that may occur when this

system is used in any way other than that for which it is

intended.

To assure safe and proper operation, all supplied

equipment, components and/or accessories must be

carefully transported and stored, as well as professionally

installed and operated. Careful maintenance and usage in

full accordance with operating instructions is imperative.

The equipment should be installed and operated only by

qualied persons who are familiar with devices of this

type.

Do not mount the DTI-Logger unit, control/display unit,

monitor(s), or any other item in any location that may

come into contact with the airbag in the event of air bag

deployment.

If the DTI-Logger unit, control/display unit, monitor(s), or

any other item is placed in the passenger seat, deactivate

the air bag to prevent accidental contact with the airbag in

the event of air bag deployment.

Equipment must be mounted rmly and securely.

Improper use or mounting of the equipment may affect

the safety of the vehicle and/or occupants. The equipment

must not be mounted and/or operated in any way that

may compromise vehicle and/or occupant safety.

Do not use defective or damaged equipment, components

and/or accessories.

Do not modify or change the equipment or its accessories

in any way.

Disconnect power from the device if the vehicle is

stationary for extended periods.

Important notes

Page 55343A_002-793e-01.18

Use only original equipment, components and/or

accessories included in the scope of delivery.

Always observe the correct operating voltages when

connecting the equipment (power supply, data acquisition

and evaluation systems and other system components).

We recommend using only the cables included in the

scope of delivery. If you think it is necessary to use

your own cables, take special note of the correct pin

assignment.

Kistler assumes no liability for damages caused due to

the use of cables other than those delivered by Kistler.

For additional information, please contact Kistler:

+49 6441 9282 0

info.de@kistler.com

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 6

2.2 Glossary

CAN Controller Area Network = serial bus system

DiMod Digitizing module for analog signals

DTI Converter CAN Module for conversion of a CAN bus to DTI

1-channel DTI

integration digital

ModulefortheconversionofaswitchinputtoDTI(highdenitionover

time)

MFDD Mean Fully Developed Deceleration = mean fully developed

deceleration relative to the distance traveled within the range (0.8 ...

0.1) · v0. Calculated for v in km/h with MFDD in m/s2 as follows:

2.3 Disposal instructions for electrical and electronic equipment

Do not dispose of old electronic instruments in municipal

trash. For disposal when the product has come to the end

of its service life, please return it to an authorized local

electronic waste disposal service or contact the nearest

KistlerInstrumentsalesofceforreturninstructions.

2.4 Software upgrades and updates

Kistler may occasionally supply upgrades or updates for

embedded software. Such upgrades or updates must

always be installed.

Kistler declines any liability whatsoever for any direct

or consequential damage caused by products running

on embedded software that has not been upgraded or

updated with the latest available software.

Product description

Page 75343A_002-793e-01.18

3. Product description

3.1 In general

The Kistler DTI-Logger Type 5343A is a compact and

powerful data acquisition system for the applications of

vehicle dynamics, fatigue strength and tire tests based on

the standard DTI bus (Digital Transducer Interface).

The use of the DTI technology ensures an efcient and

fasttestsetup.Onlyasinglecableisneededforcongu-

ration of the sensors, the transmission and synchroniza-

tion of the measured data and for the power supply. An

automatic sensor detection using TEDS thus provides an

evensimplerconguration.

The DTI-Logger is based on DTI technology, which repre-

sents a universal bus system for the complete application.

Signals are digitized as needed and a DTI signal is con-

verted. This occurs directly in the Kistler DTI sensors or

– in the case of existing sensors – via corresponding DTI

Converter. Therefore, signals can easily be transferred via

the Kistler DTI Converter CAN into DTI signals.

Because the DTI-Logger also takes care of supplying

power to the connected DTI sensors, the required cabling

can be done substantially more easily and rationally so

that the installation of the measuring system can be done

moreefciently.Together with the daisy chain capability,

this approach enables decentralized data acquisition, in

which the signals can be digitized and converted directly

at the point of acquisition. The sensor data then ow in

a fail-safe manner into the central Kistler DTI-Logger

and are transferred via Ethernet into the computer and

recorded there.

The calibration values and the relevant physical variables

are automatically detected by the KiCenter (Kistler mea-

surement software). Moreover, the KiCenter permits the

congurationofallDTIsensorsthatarepartofthemea-

suring system. This guarantees maximum process safety

andefcientuseoftime.

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 8

3.2 Application

The system can be used for, among other things:

Braking distance measurements

CO2 measurements

Transverse dynamics applications

Customer-specicapplications

3.3 Accessories

Included accessories Type/Item no.

Evaluation electronics, DTI-Logger 55151414

Power cable, DTI Logger, L = 1 m 55155613

Connecting cable, Ethernet, L = 2 m 55155608

Screw set for evaluation electronics 55123001

USB stick software & manuals 55158846

Transport box 55091649

Accessories (optional) Type/Item no.

Ethernet-to-USB adapter 22007428

Connecting cable DTI, L = 0.5 m 55155607

DTI Converter CAN 18033804

1-channel DTI integration digital 18034016

1-channel DTI integration analog 18034245

3-channel DTI integration analog 18034246

Technical data

Page 95343A_002-793e-01.18

4. Technical data

4.1 Specications

System specications

Power supply VDC 10 ... 28

Max. power consumption 1) W 35

Temperature range

Operation °C –25 ... 50

Storage °C –40 ... 85

Rel. humidity (non-condensing) % 5 ... 80

Degree of protection (cable installed) IP40

Dimensions (LxWxH) mm 164x125x65

Weight grams 900

Data inputs

Digital Input – DTI 2)

Max. sampling rate kS/s 20 3)

Number of DTI ports 4) 8

Usable slots, max. 5) 18

Data outputs

Ethernet TCP/IP yes

1) Excl. sensor power supply

2) For detailed information, see Instruction Manual 002-793d

3) Depending on the connected sensor

4) Per port, 12 Slots at 40 bytes/ms are available

5) For detailed information, see Instruction Manual 002-793d

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 10

4.2 DTI-Logger pin assignments / ports and slots

Fig. 1: DTI-Logger

8 x DTI-Ports: for the connection with DTI devices

1 x Power: For supplying power to the entire DTI measuring chain

1 x ETH: Ethernet interface with the PC

ETH, 7-pin LEMO, female

Pin Signal

1 TX+

2 TX–

3 RX+

4 RX–

5 not connected

6 not connected

7 GND

Power, 4-pin LEMO, male

Pin Signal

1 Vin_Ext

2 Vin_Ext

3 GND_Ext

4 GND_Ext

Technical data

Page 115343A_002-793e-01.18

DTI port, 8-pin LEMO, female

Pin Signal

1 RS485+

2 RS485–

3 +5.1 V DTI

4 GND

5 Vout_Ext

6 Vout_Ext

7 GND_Ext

8 GND_Ext

The DTI-Logger has 8 physical ports (see Fig.), in each

case with 12 slots per port.

Eachslotisdesignedwithaxedsamplingfrequencyof

20 kHz (20,000 samples per second).

If an analog signal (via DiMod, see glossary, chapter 2.2,

page 6) is then connected to slot 1 having an internal

sampling frequency of 1 kHz, the complete slot (with

20 kHz) is assigned.

Because the DiMod always scans with 16 bit@20 kHz,

the requirement per analog signal is always 1 slot

= 16 bits = 2 bytes * 20 000 Hz = 40 000 byte/s ≙1 Slot

Digitally, this behaves somewhat differently. Because a

slot has room for data @20 kHz@16 bit, a slot can be

used (lled) more efcient digitally so that an S-Motion

> 20 signals occupies only 2 slots on a port. We have a

maximum data rate per port of 40 bytes/ms.

If the data quantity of all signals of an S-motion is

96 bytes, it is to be multiplied by the sampling frequency

(500 Hz @S-Motion).

Calculation:

96 bytes * 500 Hz = 48 000 bytes/s = 48 bytes/ms ≙ 2

slots

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 12

CAN

The CANiMod always needs 3 slots per CAN line.

Port/slots (example)

Slot Port X

01 S625

02 S625

03 S625

04 S-Motion

05 S-Motion

06 S-Motion

07 Kistler MSW

08 Kistler MSW

09 Kistler MSW

10 HF / DFL

11 HF / DFL

12 HF / DFL

13 WPT1

14 WPT1

15 WPT1

16 WPT1

17 PFT

18 BS

Technical data

Page 135343A_002-793e-01.18

A list of our commonly used (DTI) sensors is provided

below with the number of slots required for each:

Sensor # Slots

Correvit L-Motion 1

Correvit S-MOTION 2

Correvit S-HR via DTI Converter CAN 3

Correvit SF-II via DTI Converter CAN 3

Correvit L-350/S-350 via DTI Converter CAN 3

Kistler MSW 1

KiRoad Wireless P1 4

DTI Converter CAN 3

1-channel DTI integration digital 1

DTI Converter Wind 1

RV-4 via DTI Converter CAN 3

Light 1-channel DTI integration digital 1

Brake switch via 1-channel DTI integration digital 1

WPT via 1-channel DTI integration digital 1

Pedal force sensor (DiMod) 1

DCA via DTI Converter CAN 3

HF-xxxC via DTI Converter CAN 3

MicroStar via DTI Converter CAN 3

Table 1: Sensor number/slots

The maximum limitation of the current DTI logger is 18

Slots.

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 14

4.3 DTI-Logger status LEDs

Port LEDs

As soon as the equipment is initialized, the LED lights up

white.

As soon as the current is too high (>5 A), the LED begins

toash→nofurthermeasurementpossible.

OP LED

Assoonasthesystemisinitialized,theLEDashes.

LAN LED

Assoonastrafcispresentattheport,theLEDashes

white.

Software

Page 155343A_002-793e-01.18

5. Software

The screenshots show KiCenter with language setting

English.

5.1 Toolbar

The toolbar is divided into three categories

Database Operations

Connection

Tools

Fig. 2: Device Center, toolbar

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 16

5.1.1 Explanation of the buttons in the toolbar

1. Database operations

Transferring the current settings from KiCenter to the

device.

Reads the current settings from the device.

Changes that were made in KiCenter but were not

then transferred to the device are lost in the process.

Importingdeviceparametersfromale(*kdx).

Exportingdeviceparametersintoale(*kdx).

The parameters of multiple devices can be saved in

onele.

Removal of the selected device.

2. Connection

Browse all

A search is made on all active interfaces for devices

that are not yet connected to KiCenter.

Browse: serial devices (browse serial)

All devices are searched that have only USB or USB

and RS-232C on the front panel, regardless of the

connection used (USB or RS-232C).

Browse: network devices (browse net)

All devices are searched that have a network port on

the front panel, regardless of the connection used

(LAN or USB).

Software

Page 175343A_002-793e-01.18

Conguration of serial devices

All devices that have only USB or USB and RS-232C

on the front panel, regardless of the connection used

(USB or RS-232C)

Conguration of network devices

All devices that have a network port on the front panel,

regardless of the connection used (LAN or USB).

Using the checkboxes, even more precise searching

is possible

5.1.2 Tools

Only active if a sensor is directly connected (not via DTI-

Logger).

Test output

If activated, a voltage of 5 V is output at all analog outputs

of the device and a frequency of 5 kHz at all digital out-

puts. This function is only supported by certain devices.

Device calibration

For a few devices, a calibration function is available.

Further information on the use of this function is available

in the corresponding manual of the device.

Create CAN DB

Creates a CANDBle with the device CAN settings

current in KiCenter. In order to ensure that the settings in

the CAN DB match those in the device, either the current

settings from KiCenter should be written into the device

or in KiCenter the settings from the device are updated

before the CAN DB is created. The generation of the

CAN DB is only possible from the highest sensor level

(click on sensor name).

Firmware update

A rmware update functionality is available for some

devices.

DTI-Logger data acquisition system, Type 5343A – with KiCenter

5343A_002-793e-01.18Page 18

5.2 Breaking distance application example

A braking distance application of the DTI–Logger with

KiCenter is used below for explanation.

GUI

Correvit® L-Motion

DTI-Logger

Bremsschalter

Einfache Synchronisation

der Sensoren über KiCenter.

ECU

DTI-Bus

Fig. 3: Braking distance application measuring chain

Equipment:

DTI-Logger

L-Motion incl. Engine Control Unit

Brake switch

KiCenter

After the L-Motion and the brake switch have been

connected via the power/DTI cable to any DTI-Port on the

DTI-Logger, the DTI-Logger was connected via the LAN

cable to your computer and the DTI-Logger was supplied

withcurrent,youcanthenbeginwiththecongurationin

the KiCenter.

Page is loading ...

Kistler 5343B Owner's manual

Kistler 5343B Owner's manual

Related papers

Other documents