Kichler Lighting 49791AUB is a ceiling-mounted light fixture that comes with a canopy, threaded ring, chain, and decorative loop. It is designed for indoor use and can be installed on a standard electrical outlet box. The fixture has a screw collar loop that allows for easy height adjustment. It also features a ground wire for safety. The fixture can accommodate up to 3 incandescent bulbs with a maximum wattage of 60W each (bulbs not included). It is compatible with both parallel and insulated wires. The fixture is easy to install and comes with clear and concise instructions.
Kichler Lighting 49791AUB is a ceiling-mounted light fixture that comes with a canopy, threaded ring, chain, and decorative loop. It is designed for indoor use and can be installed on a standard electrical outlet box. The fixture has a screw collar loop that allows for easy height adjustment. It also features a ground wire for safety. The fixture can accommodate up to 3 incandescent bulbs with a maximum wattage of 60W each (bulbs not included). It is compatible with both parallel and insulated wires. The fixture is easy to install and comes with clear and concise instructions.
IS-49791-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
5) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
6) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down.
7) Aach decorave loop[L] to top of main body[K]. Aach
chain to xture if required.
8) Weave electrical wire and ground wire through chain
links[H] no more than 3 inches apart. Pass wire through
threaded ring, canopy, screw collar loop, threaded pipe
and into outlet box.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire. Connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
11) Raise canopy to ceiling.
12) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
13) Insert recommended bulb(s) (Not supplied).
14) Slide glass[I] over installed bulbs and rotate into place.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain
[I] Glass
[J] Mounting
Strap Screws
[K] Main Body
[L] Decorative
Loop
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
2) Run another hexnut down threaded pipe almost touching
rst hexnut. Screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
3) Connect mounng strap to outlet box using mounng
strap screws[J].
Installaon Instrucons (connued)
E
D
C
J
A
G
B
H
F
I
K
L
Page is loading ...
IS-49791-CB
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4) Unscrew the threaded ring[F] from screw collar loop.
Take canopy[G] and pass over screw collar loop.
Approximately one half of the screw collar loop exterior
threads should be exposed. Adjust screw collar loop by
turning assembly up or down in mounng strap. Remove
canopy.
5) Aer desired posion is found, ghten both top and
boom hexnuts up against the boom and top of the
mounng strap.
6) Slip canopy over screw collar loop and thread on
threaded ring. Aach chain[H] (with xture connected)
to boom of screw collar loop. Unscrew threaded ring,
let canopy and threaded ring slip down.
7) Aach decorave loop[L] to top of main body[K]. Aach
chain to xture if required.
8) Weave electrical wire and ground wire through chain
links[H] no more than 3 inches apart. Pass wire through
threaded ring, canopy, screw collar loop, threaded pipe
and into outlet box.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is provided,
aach ground wire from outlet box under cupped
washer and green ground screw, then thread into
mounng strap.
If xture is provided with ground wire. Connect xture
ground wire to outlet box ground wire with wire
connector (Not provided) aer following the above steps.
Never connect ground wire to black or white power
supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
11) Raise canopy to ceiling.
12) Secure canopy in place by ghtening threaded ring onto
screw collar loop.
13) Insert recommended bulb(s) (Not supplied).
14) Slide glass[I] over installed bulbs and rotate into place.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
[A] Threaded
Pipe
[B] Screw Collar
Loop
[C] Hexnut
[D] Mounting
Strap
[E] Outlet Box
[F] Threaded
Ring
[G] Canopy
[H] Chain
[I] Glass
[J] Mounting
Strap Screws
[K] Main Body
[L] Decorative
Loop
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
1) Take threaded pipe[A] from parts bag and screw in screw
collar loop[B] a minimum of 6 mm (1/4”). Lock into place
with hexnut[C].
2) Run another hexnut down threaded pipe almost touching
rst hexnut. Screw threaded pipe into mounng
strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe
must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from
back of mounng strap.
3) Connect mounng strap to outlet box using mounng
strap screws[J].
Installaon Instrucons (connued)
E
D
C
J
A
G
B
H
F
I
K
L
Page is loading ...
-
1
-
2
-
3
-
4
Kichler Lighting 49791AUB is a ceiling-mounted light fixture that comes with a canopy, threaded ring, chain, and decorative loop. It is designed for indoor use and can be installed on a standard electrical outlet box. The fixture has a screw collar loop that allows for easy height adjustment. It also features a ground wire for safety. The fixture can accommodate up to 3 incandescent bulbs with a maximum wattage of 60W each (bulbs not included). It is compatible with both parallel and insulated wires. The fixture is easy to install and comes with clear and concise instructions.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 43984BK User manual
-
Kichler Lighting 42992OZLED User manual
-
Kichler Lighting 42992OZLED User manual
-
Kichler Lighting 49988DBK User manual
-
Kichler Lighting 44262AVI User manual
-
Kichler Lighting 44073DBK User manual
-
Kichler Lighting 44078BK User manual
-
Kichler Lighting 44290WWW User manual
-
Kichler Lighting 44060OZ User manual
-
Kichler Lighting 49988DBK User manual
Other documents
-
Trend TP10035 User manual
-
Bel Air Lighting 8161 ROB Installation guide
-
Kichler 59008WZC Operating instructions
-
Warehouse of Tiffany RL4804 Operating instructions
-
-
-
-
-
Golden Lighting 1567-SF PC Installation guide
-
The Home Depot 1Jay-50334BK User manual