Magma R10-1010-36 Operating instructions

Magma
Brand
Magma
Model
R10-1010-36
Category
Rack accessories
Type
Operating instructions

This manual is also suitable for

Magma R10-1010-36 is a set of stainless steel storage arms with foam pads and protective covers for Magma Kayak/SUP Storage Racks. With this device, you can securely store your kayaks and SUPs on your boat or RV. The storage arms are adjustable to fit different sizes of equipment, and the foam pads help to protect your gear from scratches and damage. The protective covers help to keep your equipment clean and dry when not in use.

Here are some of the features and possible use cases of the Magma R10-1010-36:

  • Adjustable storage arms: The storage arms can be adjusted to fit different sizes of equipment. This makes them ideal for storing a variety of kayaks and SUPs.

Magma R10-1010-36 is a set of stainless steel storage arms with foam pads and protective covers for Magma Kayak/SUP Storage Racks. With this device, you can securely store your kayaks and SUPs on your boat or RV. The storage arms are adjustable to fit different sizes of equipment, and the foam pads help to protect your gear from scratches and damage. The protective covers help to keep your equipment clean and dry when not in use.

Here are some of the features and possible use cases of the Magma R10-1010-36:

  • Adjustable storage arms: The storage arms can be adjusted to fit different sizes of equipment. This makes them ideal for storing a variety of kayaks and SUPs.
83-1010-36 0819
MAGMA PRODUCTS, INC. • 3940 Pixie Ave. • Lakewood, CA 90712 • USA • Tel: (562) 627-0500
MagmaProducts.com • [email protected]
Installation,
Care & Use Instructions
R10-1010-30 • R10-1010-36 • R10-1020
Stainless Steel Storage Arms with Foam Pads +
Protective Covers for Magma Kayak/SUP Storage Racks
CONTENTS
(2) – Stainless steel storage rack arms with foam
pads + 600D polyester protective covers
(4) – 1/4"-20 x 2" Stainless steel button socket
cap screws
(4) – 1/4"-20 Stainless steel nylock nuts
(1) – 5-/32" Hex key wrench
ADDITIONAL TOOLS REQUIRED
7/16" Wrench
INSTALLING STORAGE ARMS TO RACK
Once necessary space required between
equipment is determined, vertically
space arms accordingly. Fit attachment
bracket over vertical upright and install
(2) 1/4"-20 x 2" button socket cap screws with
(2) 1/4"-20 nylock nuts and secure using a
7/16" wrench with 5/32" hex key wrench.
NOTE: To maximize storage potential, start
installing arms from the racks top set of
holes and working down allowing minimum
space necessary between each water toy.
ADJUSTING RACK ARMS TO FIT EQUIPMENT
If additional adjustment is required to fit larger
or smaller equipment simply remove attachment
fasteners, reposition arms in the desired
location and repeat the installation procedure.
EXAMPLES OF ARM STYLES AND CONFIGURATIONS (SHOWN) OR
MIX AND MATCH TO ADAPT THE SYSTEM TO YOUR SPECIFIC REQUIREMENTS
LIMITED WARRANTY
***ORIGINAL PROOF OF PURCHASE REQUIRED FOR ALL WARRANTY CLAIMS***
Magma Products, Inc. guarantees this product to be free from defects in materials and workmanship for (1) year from the date of purchase to the original consumer. This guarantee is for the periods herein specified when used
under normal and reasonable conditions in a non-commercial or non-institutional environment. Under normal use conditions, the UV protected foam padding will withstand regular exposure to the sun’s harmful rays and is covered
by (1) year limited warranty. Tearing or ripping damage to foam padding caused by general misuse will not be covered under conditions of warranty. Additional information and full conditions of warranty visit MagmaProducts.com.
CARE & USE
• Kayak’s and SUP’s should be secured to rack when not in use
• Periodically wash rack with environmentally friendly boat soap,
fresh water, and a clean cloth to remove any debris, wipe dry
• Water toys should always be rinsed
with fresh water before storing
SECURING EQUIPMENT TO RACK
(Securing Tie-Down Straps Not Included)
• Attach hook of tie-down strap to rack’s arm
connection bracket at the main frame, extend over
equipment, and connect strap to tie-down point
  • Page 1 1

Magma R10-1010-36 Operating instructions

Magma
Brand
Magma
Model
R10-1010-36
Category
Rack accessories
Type
Operating instructions
This manual is also suitable for

Magma R10-1010-36 is a set of stainless steel storage arms with foam pads and protective covers for Magma Kayak/SUP Storage Racks. With this device, you can securely store your kayaks and SUPs on your boat or RV. The storage arms are adjustable to fit different sizes of equipment, and the foam pads help to protect your gear from scratches and damage. The protective covers help to keep your equipment clean and dry when not in use.

Here are some of the features and possible use cases of the Magma R10-1010-36:

  • Adjustable storage arms: The storage arms can be adjusted to fit different sizes of equipment. This makes them ideal for storing a variety of kayaks and SUPs.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers