Garden Oasis 302-1136135 Owner's manual

Warning

1. It is the consumer's responsibility to comply with any building codes,

ordinances, zoning limitations, or local homeowner's restrictions and

obtain any required permit, before purchase and installation of the

products.

2. Two persons are required for assembly. The tools required include

spanners (part Y and Z1 in below structure), stepladder

and other

safety items such as gloves and hardhat. To avoid injury from exposed

sharp edges, it may be necessary to use the above safety equipment.

3. This unit will take at least 5 hours to set up. Yo u must schedule

enough time to complete the assembly so you don't

leave it

unattended if not fully assembled,even if bolted to the ground.

 Make sure that all components are in the box. Read instructions

carefully before starting the assembly.

 Follow all instructions to assure the strength of the shelter.

 Help

from another person is required to assemble the shelter.

 In order to avoid damage to the shelter and its components, use

appropriate tools. Do not use the structure as a support;a

stepladder is recommended.

 Check all screws on a regular basis to maintain the solidity of

the structure.

 Keep instructions

and parts list for further use.

4. The screws to anchor on wood deck and concrete patio aren't

included.

Maintenance

If this shelter needs repairs,

DO NOT RETURN THE PRODUCT TO SEARS.

l In case of a defective part or if a problem occurs while using this

Product, please contact SOJAG at 1866-901-1649

l Use the part number on the parts list to order at your retail store

l For cleaning: Use a domestic soap or detergent and wash with warm

water using a sponge or fabric. Rinse with clean water.

Attention

Your shelter has been created for all four seasons and will

resist to snow accumulations of 3500 lb;however,we strongly

suggest removing any excess of snow on the roof.

The mosquito nets must be removed for winter storage.

WARRANTY

 Limited warranty applicable on parts only

 Products distributed by SOJAG are built with high standard.

 Products distributed by SOJAG are guaranteed against defective

materials for three (3) years based on normal use of the product.

EXCLUDED:

1. Damages due to vandalism, abuse and wrong use of the product is not

covered by the warranty.

Damage due to extreme weather conditions such as thunderstorm and

windstorm.

Roof side structure

Coner cover

J

1

J2

Solidifying bar

Column cap

Joint cover plate

Cornice

Na

Nb

M6x20

16PCS

8PCS

W

X

Allen

Z1

S1

M6x35

165PCS

O1

M6x16

72PCS

St5x16

8PCS

Y1

Z3

Z2

Solidifying bar

V

 Install columns (A) on bases (H) using

screws (V)

A

H

1

Step 1

Step 2

Assemble column

Assemble the cornice

 Attach the (B) to the cornice (B1)

with screw (V). Repeat with the cornice (C

and C1)

cornice

C

1

B

1

V

/4

/2

2

Step 3 Assemble the structure

C

1

 Install the (B and B1) between two (2)

columns and screw together with screw (T). Repeat

with the (C and C1)

cornice

V

T

Z

1

C1

C

B

B1

B

C1

C

T

L

W

3

Step 4

Assemble corner covers and the joint cover plates

 Install the column caps (I1) on the columns (B2)

using screws V)

 Screw the joint cover plates (L) using screws (W)

on the joint between the (C and C1)

 Screw the corner covers (I)

using screws (W)

cornice

I

W

V

I1

B2

W

/4

Step 5 Tracks installation

 Install solidifying bars(K)inside each

structure bar using screws(V)

 Install solidifying bars(Z2,Z3)inside each

structure bar and join the other end to the

columns using screws(V)

V

K

Z2

Z3

Z2

V

K

V

Z2

Z3

/4

Z2

Z3

4

6xX

B

2

 Slide 6 hooks (X) into each track section (B2)

and 7 hooks (X) into each track section (C2).

 Place tracks (B2) on the structure bars (B&B1)

ith screws (V). Repeat with sections (C2) on

the structure (C&C1).

1w

5

Step6 Tracks installation

7xX

C

2

V

C

2

V

B

2

B2

C2

/4

/52

X

 Fix the roof side structure (G, G1 & G2) on the

(B, B1, C, & C1) using screw (W).cornice

Step 7 Tracks installation

6

G

2

G

1

G

1

W

B

W

/4

/2

 Install iron angles (O,O1) on roof bars (D,E)

using screws (V)

7

Step9

O

V

O1

V

D

E

/4

/6

/4 /6

O1

O

8

Step10

 Install roof bars (D) one at a time to

the inside roof connector (S1) using

bolts and nuts (V) and screw them to

the columns (A) by screwing the

iron angles (O) with screws (V).

Repeat for all four (4) bars.

L

V

D

S1

D

V

S1

V

O

/1

S1

Step11

Roof connector installation

V

S1

S

 Install roof bars (E) to the inside

roof connector (S1) using bolts

and screws (V) and screw them to

the (B, B1, C & C1) by

screwing the iron angles (O1)

with screws (V). Repeat for all

six bars (E).

cornice

 Install the outside roof connector (S)

to the inside

roof connector (S1)

using screws (V). Don't over tighten

before placing the polycarbonate

roof panels.

9

E

S

V

S1

E

V

E

S

1

O1

/1

You MUST anchor the sun shelter before installing the roof:

Make sure to level the platform (floor) properly before.

Grass surface: Use camp nails (Z) to anchor (included) (NOTE: This is a

temporary solution)

Wood deck: Use wood screws to anchor (not included)

Concrete patio: Use Tapcon screws to anchor (not included)

IT IS IMPORTANT TO PLACE THE PANELS THE PROPER

WAY SO THAT THE UV PROTECTION IS ON THE

EXTERIOR.

IT IS IMPORTANT THAT THE PANELS AND THE ROOF

SUPPORT BARS ARE WELL IN PLACE, ONE IN THE OTHER.

Attention Warning

This

side up

10

This

side up

Ma

1

Mb

1

Ma

1

Install one roof pannel (Ma), a roof

support bar (J) and a roof pannel (Mb)

Continue like this until the roof be done

Ma

1

Ma

1

Mb

J

2

J1

Na

Nb

Ma

Mb

J

11

Step12

Assemble the roof panels

Z

1

/4

/2

Na Nb

Z1

/4

/2

/4

JJ1

J2



Fix the roof finishing side bar (F, F1 and F2)

using screw (V).

Install at the end of all roof bars (D)

finishing ends (Q) and finishing ends (R) for

roof bars (E) using screws (V) that you can

now tighten properly.

Step 13

Assemble the roof panels

V

Q

F

V

R

F

1

F2

F1

F

V

R

/4

/2

/4

/6

12

 Install the mosquito netting (P) along the tracks

on the hooks (X).

Step 15

Final assembly

14

/1

Made in CHINA

Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

See our extensive assortment of outdoor living products

on-line at www.sears.com and www.kmart.com

For questions or comments about product:

Email: [email protected] or Call toll-free: 1-866-901-1649

sears.com

Please refer to part numbers when reordering

Garden Oasis 302-1136135 Owner's manual

Garden Oasis 302-1136135 Owner's manual

Other documents