HP BLc3000 Dual DDR2 Onboard Administrator User guide

Brand: HP

Model: BLc3000 Dual DDR2 Onboard Administrator

Category: Console servers

Type: User guide

This manual is also suitable for

BLc3000 DDR2 Onboard Administrator

HP c3000 DDR2 Onboard

Administrator

Installation Instructions

for HP BladeSystem c3000 and c3000 Tower Enclosure

Introduction

There are two optional Onboard Administrator modules available

with the enclosure:

• HP c3000 DDR2 Onboard Administrator module, part number

488099-B21

• HP c3000 Dual Onboard Administrator module, part number

488100-B21

To use the Onboard Administrator modules, you must have HP

BladeSystem Onboard Administrator version 2.30 or greater

installed. For more information on using the Onboard Administrator

software, see the

HP BladeSystem Onboard Administrator User

Guide.

You can install the optional HP c3000 DDR2 Onboard Administrator

module in the enclosure without a second module.

Before you install an HP c3000 Dual Onboard Administrator in the

enclosure, you must have installed the c3000 DDR2 Onboard

Administrator module.

NOTE: The HP BladeSystem c3000 Enclosure is shown

in the illustrations throughout this document. The HP

BladeSystem c3000 Tower Enclosure is rotated 90

degrees clockwise from what is shown in the

illustrations.

HP c3000 DDR2 Onboard

Administrator module components

Item Name Description

1 Insight Display A display that

provides

information about

the health and

operation of the

enclosure

2 Serial connector Serial RS232 DB-9

connector with PC

standard pinout.

3 UID LED Blue = UID on

Dark = UID off

Item Name Description

4 Active Onboard

Administrator LED

An LED that

indicates which

Onboard

Administrator is

active

5 Health LED Green = OK

Red = Critical error

6 USB A USB 2.0 Type A

connector that

connects supported

USB devices

7 Reset button —

HP c3000 Dual Onboard

Administrator module components

Item Name Description

1 Serial connector Serial RS232 DB-9

connector with PC

standard pinout

2 UID LED Blue = UID on

Dark = UID off

3 Active Onboard

Administrator LED

An LED that

indicates which

Onboard

Administrator is

active

4 Health LED Green = OK

Red = Critical error

5 USB USB 2.0 Type A

connector that

connects supported

USB devices

6 Reset button —

Upgrading an HP Onboard

Administrator module to an HP

c3000 DDR2 Onboard

Administrator module

1. Disconnect all cables from the HP Onboard Administrator

module.

2. Remove the HP Onboard Administrator module.

3. Slide either the c3000 Dual Onboard Administrator module (if

ordered) or an Onboard Administrator blank into the c3000

DDR2 Onboard Administrator module, and close the handle.

The information contained herein is subject to change without notice. The

only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing

herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Bluetooth is a trademark owned by its proprietor and used by Hewlett-

Packard Com

under license.

Part Number 488456-002

September 2009 (Second Edition)

4. Slide the c3000 DDR2 Onboard Administrator module into the

bay, and close the handle.

5. Reconnect all cables.

NOTE: To use the Insight Display in the HP

BladeSystem c3000 Enclosure, press to release it, flip it

up, and then rotate it 90 degrees clockwise. See the

BladeSystem c3000 Enclosure Quick Setup Instructions

HP BladeSystem c3000 Enclosure Setup and

Installation Guide

for more information.

Installing a c3000 Dual Onboard

Administrator module

1. If necessary, remove the installed Onboard Administrator

blank.

2. Slide the c3000 Dual Onboard Administrator module into the

3000 DDR2 Onboard Administrator module, and close the

handle.

Replacing the HP c3000 Dual

Onboard Administrator module

1. Disconnect all cables from the HP c3000 Dual Onboard

Administrator module.

2. Press the release button, pull the handle open, and remove the

HP c3000 Dual Onboard Administrator module from the

enclosure.

3. Install a c3000 Dual Onboard Administrator module in

Onboard Administrator bay 1.

4. Reconnect all cables.

Replacing the HP c3000 DDR2

Onboard Administrator module

1. Disconnect all cables from the HP c3000 DDR2 Onboard

Administrator module.

Press the release button, pull the handle open, and remove the HP

c3000 DDR2 Onboard Administrator module from the enclosure.

2. Remove the c3000 Dual Onboard Administrator module or

Onboard Administrator blank from the c3000 DDR2 Onboard

Administrator module.

3. Slide the c3000 Dual Onboard Administrator module or blank

into the replacement c3000 DDR2 Onboard Administrator

module, and close the handle.

4. Slide the c3000 DDR2 Onboard Administrator module into the

bay, and close the handle.

Regulatory compliance notices

Class A equipment

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to

radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the user

will be required to correct the interference at personal expense.

Modifications

The FCC requires the user to be notified that any changes or

modifications made to this device that are not expressly approved by

Hewlett-Packard Company may void the user’s authority to operate

the equipment.

Cables

Connections to this device must be made with shielded cables with

metallic RFI/EMI connector hoods in order to maintain compliance

with FCC Rules and Regulations.

Canadian notice

This Class A digital apparatus meets all requirements of the

Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences

du Règlement sur le matériel brouilleur du Canada.

European Union regulatory notice

This product complies with the following EU Directives:

• Low Voltage Directive 2006/95/EC

• EMC Directive 2004/108/EC

Compliance with these directives implies conformity to applicable

harmonized European standards (European Norms) which are listed

on the EU Declaration of Conformity issued by Hewlett-Packard for

this product or product family.

This compliance is indicated by the following conformity marking

placed on the product:

This marking is valid for non-Telecom products and EU harmonized

Telecom products (e.g. Bluetooth).

This marking is valid for EU non-harmonized Telecom products.

*Notified body number (used only if applicable—refer to the product

label)

Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034

Boeblingen, Germany

The official EU CE declaration of conformity for this device can be

found on the

HP website (http://www.hp.com/go/certificates).

Korean class A notice

Japanese class A notice

HP BLc3000 Dual DDR2 Onboard Administrator User guide

Brand: HP

Model: BLc3000 Dual DDR2 Onboard Administrator

Category: Console servers

Type: User guide

This manual is also suitable for

BLc3000 DDR2 Onboard Administrator

Download PDF

report

HP BLc3000 Dual DDR2 Onboard Administrator User guide

This manual is also suitable for

HP BLc3000 Dual DDR2 Onboard Administrator User guide

Related papers

Other documents