Page 1 of 5
AquaVapor Cig MyGo Variable Voltage eCig
Thank you very much for purchasing the AquaVaporCig MyGo. We have two version of the MyGo Variable Voltage Electronic
Cigarette. You can determine the version you have by the material used on the end cap that screws off to insert battery into
housing. If your device has a plastic end cap you have a V1 MyGo if the cap is metal and the display has a battery charge indicator
bar your device is a V2 MyGo. Based on your version the device will have slight differences which are described below.
V1 Functions
1) Adjust the voltage from 3v to 6v by pressing the + of - button, the higher the voltage the more vapor produced.
2) Short circuit self-protection. When atomizer resistance is below 1.3ohm, or incorrect usage (such as reverse battery) leading
to short circuit, the device will turn itself off.
3) The max working current is up to 1.5 amps. But we limit the Atomizer Resistance to 1.3ohms, if below 1.3 Ohms the device
will turn itself off.
4) Regulated output which keeps the voltage the same with each puff - regardless of your remaining battery power. As the
battery drains, the device will keep the voltage consistent.
5) Vent hole on the bottom cap of the device for added safety.
6) Turn the device on and off by holding down the power button for 5 seconds.
7) Check the remaining battery voltage by pressing the power button 7 times consecutively within 3 seconds.
8) Lock in the selected voltage by holding down the + and – button simultaneously for 5 seconds. Unlock by doing the same. This
is useful for when you find your desired voltage and don’t want it to change if the voltage buttons are accidentally pressed.
V2 Functions
1) Adjust the voltage from 3v to 6v by pressing the + of - button, the higher the voltage the more vapor produced.
2) Short circuit self-protection. When atomizer resistance is below 1.3ohm, or incorrect usage (such as reverse battery) leading
to short circuit, the device will turn itself off.
3) The max working current is up to 3.5 amps. But we limit the Atomizer Resistance to 1.3ohms, if below 1.3 Ohms the device
will turn itself off.
4) Regulated output which keeps the voltage the same with each puff - regardless of your remaining battery power. As the
battery drains, the device will keep the voltage consistent.
5) NEW - Metal caps for both top and bottom for added durability.
6) NEW - Larger 3mm Vent hole on the bottom cap of the device for added safety
7) NEW - When you use a voltage meter or testing tool to test the voltage, there will be only 0.2v voltage difference between the
voltage without load (without atomizer attached) and the voltage under load (with atomizer attached).
8) NEW - Turn the device on and off by pressing the power button 5 times within 3 seconds.
Page 2 of 5
a. To lock the voltage in on the device turn the device on, set the voltage, then turn the device off by pressing the
power button 5 times. Now press the power button 1 time and the device will operate at the voltage it was set to
before you turned it off but the display will not illuminate when you press the voltage or power buttons and the
voltage can’t be changed when in this mode. To turn the device back on completely with access to change the
voltage with display functional just press the power button 5 times.
9) NEW - Remaining battery charge is displayed by battery bar graphic on right of LCD screen.
10) NEW - Measure and display the resistance of the atomizer by pressing the power button 1 time. The atomizer ohm resistance
will display on the screen for 3 seconds.
11) NEW - Will hold up to a 67mm battery which means 18650 batteries with nipple and/or protection circuit will fit and end cap
will screw tightly closed as long as they are not longer than 67mm.
Getting to know your MyGo
Once you have determined the version you have using the information above and have read the above features you are ready to
prepare your device for the first use.
Use the below graphics to familiarize yourself with the components of the device as we’ll reference them several times in the
instructions.
Page 3 of 5
Getting Started
Charge Batteries
1) Plug the 18650 Battery Charger into a power source. The indicator light on charger will illuminate green.
2) Insert an 18650 battery into charger being sure the positive side of battery (side with nipple) is inserted on the positive side of
the charger (indicated with + symbol).
3) Indicator light on charger will turn red indicating the battery is charging.
4) When indicator light turns green or begins to flicker green and red the battery is fully charged and should be removed from
charger immediately.
5) Charging time for the 18650 battery will range between 3 – 6 hours.
6) Never leave charging batteries unattended and always remove battery from charger immediately after charging is complete.
Assemble Device
1) Your batteries come with a partial charge so you can use the 2nd battery to begin using your device while the 1st battery is
charging.
2) Remove the End Cap from the MyGo tube.
3) Insert the 18650 battery into the tube with the positive end of the battery inserted first then replace the end cap. The
negative end of the battery should be facing the end cap.
4) Power on device
a. For V1 hold down the power button for 5 seconds until the LCD screen illuminates
b. For V2 press the power button simultaneously 5 times within 3 seconds and the LCD screen will illuminate.
5) Installing atomization attachment
a. 510 atomizer and blank cartridge
Screw the 510 atomizer into the Accessory Fitting on tube top
Fill the 510 blank cartridge with liquid and insert the cartridge into the end of the 510 atomizer
b. 510 DCT
Fill the DCT tube with liquid (see our site for detailed instructions on filling the DCT)
Screw the DCT into Accessory Fitting on tube top
c. Cartomizers
Fill the cartomizer with liquid (see our site for detailed instructions on filling cartomizer)
Screw the cartomizer into Accessory Fitting on tube top
d. eGo Attachments
Screw the eGo adapter into Accessory Fitting on tube top
Fill the eGo assessor with liquid (see our site for detailed instructions on filling)
Screw the eGo accessory into eGo adapter that you screwed into Accessory Fitting
Page 4 of 5
Device Usage
Begin Using
1) With the device assembled and power on, press the Usage Button and hold it down while taking a puff. Release the button
after taking a puff.
2) To increase or decrease vapor and flavor you can adjust the voltage by pressing the + and – Voltage Adjustment buttons until
you reach the desired flavor and vapor.
3) For best performance, flavor, and vapor you should take 3-5 second puffs and wait at least 30 seconds between puffs.
4) A regular cigarette is around 10 puffs so after taking 10 puffs you should wait the normal amount of time you do between
smoking regular cigarettes before taking your next 10 puffs.
Device Features / Functions
Changing the Voltage
1) Press the Voltage Adjustment buttons to change voltage
a. Pressing the + button will increase the voltage in increments of .1
b. Pressing the - button will decrease the voltage in increments of .1
2) Lock in the desired voltage
a. Hold down the + and – button simultaneously for 5 seconds to lock in the selected voltage.
b. Unlock the selected voltage by holding down the + and – button simultaneously for 5 seconds.
c. When a voltage is locked in it prevents the voltage from being changed when the + or – buttons are pressed
accidentally.
Checking the Remaining Battery Charge
1) Check the remaining battery charge
a. V1 Device - Check the remaining battery voltage by pressing the power button 7 times consecutively within 3
seconds.
b. V2 Device - Remaining battery charge is displayed by battery bar graphic on right of LCD screen.
Checking the Atomizer ohm Resistance
2) Check the atomizer ohm resistance
a. V1 Device – Not available
b. V2 Device – With an atomizer/cartomizer attached press the power button and the ohm’s are displayed on the LCD
for 3 seconds
Page 5 of 5
Charging Batteries
When to Charge
1) There are several indicators you can use to determine when your battery needs charging
a. V1 Device - When the remaining battery voltage is at or below 3.5 volts which can be checked by pressing the power
button 7 times consecutively within 3 seconds.
b. V2 Device – Battery charge indicator on LCD only has 1 bar remaining
c. If you allow your battery to run extremely low the LCD screen will blink when you press the atomizer activation
button.
d. If you allow your battery to run completely dead the device will turn off and the LCD screen will not illuminate when
the power button is pressed. If this happens, verify the battery is dead by trying to turn the device on. If the device
will not turn on the battery is dead.
Charging Batteries
1) Plug the 18650 Battery Charger into a power source. The indicator light on charger will illuminate green.
2) Insert an 18650 battery into charger being sure the positive side of battery (side with nipple) is inserted on the positive side of
the charger (indicated with + symbol).
3) Indicator light on charger will turn red indicating the battery is charging.
4) When indicator light turns green or begins to flicker green and red the battery is fully charged and should be removed from
charger immediately.
5) Charging time for the 18650 battery will range between 3 – 6 hours.
6) Never leave charging batteries unattended and always remove battery from charger immediately after charging is complete.
General Information
1) Visit our website www.AquaVaporCig.com for additional information on this device and to order accessories and supplies.
2) Visit our YouTube channel www.YouTube.com/aquavaporcig to view videos on this device and all our products
3) Join us on Facebook at www.Facebook.com/aquavaporcig to connect with other fans, ask us questions, and to receive special
Facebook promotions.
4) Contact us at [email protected] or via phone (888) 782-0167 if you have any questions not covered in this manual or to
order supplies.
5) If you are missing anything from your order or you received a defective item please contact us.
AquaVapor LLC
124b South Main Street
P.O. Box 509
Broadway, NC 27505
(888) 782-0167
www.AquaVaporCig.com
sales@aquavaporcig.com
/
