Aquascale 15-40-002 Instructions For Assembly And Use

Brand: Aquascale

Model: 15-40-002

Type: Instructions For Assembly And Use

READ BEFORE USE AND KEEP FOR FUTURE REFERENCE

BABY BATH STAND

Instructions for assembly and use

Intended for use with the aquascale baby bath

The aquascale stand conforms to EN1466:2004+A1:2007

Welcome

Safety instructions

Care and maintenance

The aquascale stand is designed specically for use with the aquascale 3-in1 baby bath.

WARNING: Use only on rm ground which is horizontal, level and dry.

Ensure there is enough space around the bath to safely handle the child in and out of

the bath.

WARNING: Do not let other children play unattended near the aquascale stand.

Ensure bath stand is fully open and that the two leg braces are locked into position.

Regularly check that all nuts, bolts and assembly ttings are tight and secure before

use.

WARNING: Do not use the bath stand if any parts are damaged, missing or loose.

Do not move the bath stand whilst bathing baby, or when there is water in the bath.

Only use spares approved by the manufacturer.

Do not use the bath stand for purposes other than what it was designed for.

When the aquascale stand is not in use it must be folded away.

Wipe clean using a mild soap and warm water. Dry thoroughly.

Never use ammonia based, bleach or spirit cleaners.

Do not use abrasive cleaners or abrasive pads.

Ensure product is dry before storing.

Always check parts regularly for tightness of nuts bolts and assembly ttings - tighten if

required. To maintain the safety of your nursery product, seek prompt repairs for bent,

worn or broken parts.

Thank you for purchasing this aquascale baby bath stand.

Please read the instructions and safety advice carefully before use, to

ensure safe and satisfactory operation of this product. Your child’s safety is your respon-

sibility.

If you have a query with this product or require replacement parts, please contact the

Helpline on 0161 335 2508.

Lay out the parts on a soft level surface and compare them to the parts list below. Do

not discard any packaging until you are sure that you have all the parts.

Keep children clear during assembly as the pack may contain small parts

which could present a choking hazard. Once you have identied the

parts all plastic covers should be removed, destroyed or kept away from

children.

Parts list

Contained in your carton are:

Pt Description Qty

A1-A2 Pairs of legs 2

B1 Leg strut (narrow) 1

B2 Leg strut (wide) 1

C1 Top rail (narrow) 1

C2 Top rail (wide) 1

D1 Bath support (narrow) 1

D2 Bath support (wide) 1

E Bolts (22mm) 4

F Bolts (25mm) 8

G Plastic washers 4

H Nuts 12

I Spanner 1

J Allen key 1

418mm

438mm

448mm

475mm

E F G H I J

455mm

486mm

Assembling the bath stand

Open both sets of legs (A1) and (A2)

fully. Place them so that the braces are

facing inwards towards one another.

Using the narrower strut (B1) for the

narrower set legs and the wider strut

(B2) for the wider set legs, join the two

sets of legs and secure using eight

25mm bolts and eight nuts.

Ensure all eight nuts and bolts are fully

tightened using the supplied Allen key

and spanner.

wider set legs

narrower set legs

braces

Assembling the bath stand

Using the narrower top rail (C1) for the

narrower set legs and the wider top rail

(C2) for the wider set legs, push the open

ends of the top rails onto the ends of the

legs.

Using the narrower bath support (D1) for the narrower set legs and the wider bath

support (D2) for the wider set legs, place the bath supports between the legs and

secure using four 22mm bolts, four plastic washers and four nuts.

Note: Place the washers between the legs and the bath supports.

Check nothing is loose and ensure ALL nuts and bolts are fully tightened using the

supplied Allen key and spanner.

Folding the bath stand

To fold: Unlock both braces (1) by raising them in the centre by approximately an inch.

Holding the two top rails, draw them together (2).

[email protected].uk

Imported by Kooltrade. M34 3QA

www.theaquascale.co.uk

Tel: 0161 335 2508

Aquascale 15-40-002 Instructions For Assembly And Use

Brand: Aquascale

Model: 15-40-002

Type: Instructions For Assembly And Use

Download PDF

report

Aquascale 15-40-002 Instructions For Assembly And Use

Aquascale 15-40-002 Instructions For Assembly And Use

Related papers

Other documents