Whirlpool AWE 98612 ZEN Program Chart

Brand: Whirlpool

Model: AWE 98612 ZEN

Category: Washing machines

Type: Program Chart

Whirlpool is a registered trademark of Whirlpool USA.

The wool/handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of

Woolmark garments labelled as “machine wash” or “hand wash”provided that the garments are washed according to the

instructions on the garment label and those issued in this programme chart. M0703

5019 312 11186

Programme

Tempe-

rature

Care

Labels

Max.

Load

Type of wash / Notes

- Respect the manufacturer's recommendations on the care label

Detergents and additives Options Spin

Pre-

wash

Main

wash

Softener Pre-

wash

Rapid Colours

15°

Finish on

time

Intensive

rinse

Tumble

fresh

Spin Max

spin

speed

rpm

Mixed

15 - 60°C 3.0

Lightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends.

Effective one-hour programme. Make sure to wash only similar colours together in one wash load.

– Yes

– –

i i i i i

max.

Fabrics

Cotton

15 - 95°C 6.0 Normally to heavily soiled towels, underwear, table and bed linen etc. made of cotton and linen.

Yes

i i i i i i i i

max.

Synthetics

15 - 60°C 3.0

Normally soiled garments made of artificial fibres (like polyester, polyacryle, viscose etc.) or

their blends with cotton.

Yes

i i i i i i i i

max.

Delicates

15 - 40°C 1.5 Curtains and delicate clothing, dresses, skirts, shirts and blouses.

Yes

i i

–

i i

–

i i

1000

Wool /

Handwash

15 - 40°C 1.0

Woollens, labelled with the Woolmark and identified as machine washable, as well as textiles

made of silk (keep to care label!), linen, wool and viscose marked as handwashable.

This programme is tested and approved by The Woolmark Company for machine- and handwashable wool.

– Yes

– –

i i

–

i i

1000

Jeans

15 - 60°C 4.0

Normally soiled cotton jeanswear and garments made of jeanslike material such as trousers and

jackets.

Yes

i i i i i i i i

1000

Colours

White

15 - 60°C 6.0

Normally to heavily soiled and robust cotton laundry.

Save energy by selecting a lower wash temperature and adding an oxygen-based bleach product, in addition

to your detergent

– Yes

– –

i i i i i

max.

Light colours

15 - 60°C 4.0

White and pastel shaded garments made of delicate fabrics.

Gentle wash programme to avoid graying or yellowing of your laundry. Use heavy duty detergent, if

necessary also stain removers or bleaches on oxygen basis. Do not use liquid detergent.

Yes

i i i i i i i i

1000

Dark

15 - 60°C 4.0

Black and dark garments made of cotton, cotton blends and polyester.

Special programme to reduce colour fading and local discolouration. Prefer to use a liquid detergent for

dark garments with this programme.

Yes

i i i i i i i i

max.

Eco

Super Silent

15 - 60°C 6.0

Robust laundry made of cotton or linen.

Programme optimized for silent washing and spinning, for example during the night. If you want to avoid

completely noise of spinning at night, set spin speed to “0” and start spin programme in the morning, or

define programme start with “Finish on time” accordingly.

– Yes

– –

i i i i i

1000

AquaEco

15 - 40°C 2.5

Lightly soiled laundry made of synthetic fibres, or synthetics mixed with cotton garments.

Saving programme with a very low water consumption. Use liquid detergent and the lowest recommended

amount for 3kg laundry. Do not use softener.

– Yes – – –

i i

–

i i

max.

Speed 15´

15 - 30°C 3.0

Briefly worn clothing made of cotton, artificial fibers and blends with cotton.

Refresh programme. Use lowest recommended detergent amount.

– Yes

– –

i i

–

i i

max.

EcoCotton

40 - 60°C 6.0

Normally soiled cotton laundry.

Most favourable programme in terms of combined water and energy consumption for washing cotton

laundry. - Reference programme for the Energy Label.

– Yes

– – –

i i i i

max.

Rinse & Spin

6.0

Rinse and intensive spin programme.

Same as the last rinse and the final spin in the “Cotton” programme.

– –

– – –

i i i i

max.

PROGRAMME CHART

A. Programme selector

B. “Temperature” button

C. Temperature display

D. “Spin” button

E. “Finish on time” button

F. Time display

G. “Start(Pause)” button

H. Programme sequence indicator

I. “Door open” indication

J. “Reset/Drain” button

This washing machine is equipped with

automatic safety functions which detect and

diagnose faults at an early stage and react

appropriately:

K. “Service” indication

L. “Water tap closed” indication

M. “Clean filter” indication

Acustic noise level :

Washing - 51 dB(A) / 1pW

Spinning - 1200, rpm, 72 dB(A) / 1pW

i: optional / Yes : dosing required

For improved garment care, spin speed is restricted in these programmes.

°C

h. min.

5019 312 11186

Whirlpool is a registered trademark of Whirlpool USA.

Add detergent as indicated an the front page and as

described in the chapter “Detergent and Additives” in

your Instructions for Use.

1. Turn the programme selector to the desired

programme. The display shows the programme

duration in hours and minutes as well as the

predefined temperature. The “Start(Pause)”

button flashes.

2. The temperature can be altered by pressing the

“Temperature” button.

3. The indication lamp of the predefined spin speed

lights up; in case you want to set another spin speed,

press the “Spin” button.

ADD DETERGENTS, CLOSE THE LID AND

SELECT THE PROGRAMME

PROGRAMME START

Open the tap and press the “Start(Pause)” button.

The indication lamp next to the “Start(Pause)” button

lights up. The programme sequence indicator shows the

current programme phase, running from left to right

through Wash, Rinse, Spin/Drain.

The display shows the remaining programme time. Due

to variations in load and temperature of inlet water, the

remaining time is newly calculated in certain programme

phases. If this is the case, an animation appears on

the time display.

CONSUMPTION DATA

“Colours 15° ” button

• Saves energy used for water heating while maintaining a

good wash result.

• Supports colour maintenance when washing coloured

laundry.

• Recommendable for lightly soiled laundry without stains.

• Make sure that your detergent is suitable for cold wash

temperatures (15 or 20 °C).

• Not selectable for Cotton 70 - 95°C.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helping people with

allergies.

“Tumble fresh” button

• Select this option if you cannot unload the laundry soon

after programme end, or if you tend to forget the

laundry in your washing machine. It will help to keep

your laundry fresh.

• The washing machine will start to tumble the laundry

periodically after programme end.

• The light of the “Tumble fresh” button will blink while

this function is active, and the display will show an

animation.

• The periodic tumbling will last up to approximately 12

hours after the end of your wash programme, and you

can stop it at any time by pressing the “Tumble fresh”

button. It will last a while until you can open the door.

• After the “tumble fresh” period has run out, the display

indicates “End”

SELECT ANY DESIRED OPTION

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand, granular

dirt) sensible. Increases the cycle time by approximately

15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Rapid” button

• Enables quicker washing by shortening the programme

duration.

• Recommendable for small loads or only lightly soiled

laundry.

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with

respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer

to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

** Standard Cotton programme and basis for Energy Label

“DOOR OPEN” INDICATION

Before starting and after end of a programme, the lamp

lights to show the the lid can be opened. As long as a wash

programme is running, the lid remains locked and must on

no account be forced open. In case you have an urgent need

to open it during a running programme, refer to “Cancel a

running programme before the end”.

PROGRAMME END

• The lights of the programme sequence indicator are

dark, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open lid and drum and unload the machine.

4. Leave the lid open to allow the inside of the machine to

dry.

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

1. Press the “Start(Pause)” button to pause the

programme. The light blinks.

2. Select the new programme, temperature, any options

and another spin speed if you want.

3. Press the “Start(Pause)” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

CANCEL A RUNNING PROGRAMME BEFORE

THE END

The “Reset/Drain” button cancels a programme before

the end.

• Press the “Reset/Drain” button for at least 3 seconds.

The water is drained out; it may last a while until you can

open the lid.

FINISH ON TIME

With this function you can postpone your programme to

complete at a later time: press the button to select in how

many hours the programme shall be finished. Thus, it allows

you to have your laundry ready at a particular time and to

profit from more favourable energy rates during the night,

for example.

• Do not use liquid detergent when activating this function.

• The time until the “Cycle end” can be selected in full

hour time segments (1 to 24 h). When you press the

button, the shortest possible time will be displayed; keep

on pressing the button to loop through all the available

times. To remove it again, keep on pressing the button

until you see the value “0:00”.

• When you have selected the desired time until the

“Cycle end”, press “Start(Pause)” - the countdown

will begin.

• During the countdown, you can still modify the

programme setting (select or deselect options, change

spin speed etc.). If the modifications prolong the

programme duration so that it overruns the originally

set time until the “Cycle end”, the programme will start

immediately.

• Sometimes the programme may finish before the

selected time until the “Cycle end” has expired (e.g.

for small loads). In this case, the washing machine will

tumble the laundry regularly to keep it fresh, until the

selected “Cycle end” time has expired. During tumbling,

the display will show an animation. The tumbling phase

can be stopped at any time either by pressing any button

or by rotating the programme selector; the animation

will stop and the door will unlock in about 1 minute as

indicated on the display.

FAILURE INDICATIONS

In case of any failures or irregularities, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Service”

Lighting up of the “Service” indication can be caused

by a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your “Instructions for Use”; if

the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap: if the indications still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain

hose is kinked or the filter must be cleaned: in the latter case

refer to the Instructions for Use (“Removing the Filter”).

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

without

“Rapid”

(kWh)

ApproxProgrammeDuration (hours : minutes)

without “Rapid” with “Rapid”

Mixed 40 3.0 45 0.43 1:00 –

Cotton 95 6.0 55* 1.85 2:05 1:55

Cotton 60 6.0 48 1.02 2:30 1:45

Cotton 40 6.0 48 0.60 2:30 1:30

Synthetics 60 3.0 54* 0.85 1:55 1:14

Synthetics 40 3.0 50 0.50 1:40 0:59

Delicates 40 1.5 50 0.55 0:45 –

Wool/Handwash 40 1.0 40 0.55 0:35 –

Jeans 40 4.0 41 0.58 1:30 1:10

White 40 6.0 48 0.65 2:45 –

Light colours 40 4.0 67 0.50 1:20 1:00

Dark 40 4.0 41 0.58 1:40 1:10

EcoCotton ** 60 6.0 48 0.67 3:30 –

EcoCotton ** 60 3.0 34 0.56 2:30 –

EcoCotton 40 6.0 48 0.61 3:15 –

EcoCotton ** 40 3.0 34 0.47 2:30 –

AquaEco 40 2.5 19 0.43 1:00 –

Speed 15´ 30 3.0 30 0.15 0:15 –

Super Silent 60 6.0 48 0.78 4:00 –

“Spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled, and the water is drained out only. However,

intermediate spin peaks remain during the rinse phase.

Whirlpool AWE 98612 ZEN Program Chart

Brand: Whirlpool

Model: AWE 98612 ZEN

Category: Washing machines

Type: Program Chart

Download PDF

report

Whirlpool AWE 98612 ZEN Program Chart

Whirlpool AWE 98612 ZEN Program Chart

Related papers

Other documents