5019 496 96031
GB
Quick Reference Guide
Before using the dishwasher, read the user instructions!
(We reserve the right to make technical modifications)
GMI5554/1
Add regeneration salt
Only add regeneration salt immediately before
starting a wash programme.
Add rinse aid
Antebacterial rinse (Sani-Rinse option)
This function executes an antibacterial rinse at the
end of the wash cycle, thereby further reducing
bacteria levels. The lamp will light up when the
function is activated. If the temperature is not
maintained during the antibacterial cycle
(e.g. if the door is opened or a power failure
occurs), the lamps will start blinking to indicate
that the antibacterial action is not guaranteed.
Half load function
Recommended when the dishwasher is not full to
save water and electricity. Press the button to
wash the top rack. Press the button to wash the
bottom rack. Press the button again to deactivate
the function. The indicator light and display show
that only one rack is selected.
WARNING:
This function remains selected until
switched off.
“Delayed start” button
The wash cycle can be programmed to start after
1-12 hours. Then press the Start button. After a
prewash the set delay will start.
Display
The display shows all the information relating to
the selected functions and the indication about all
functional failures (see table on the “Instructions
for Use” manual).
1) Reference programme for energy label in compliance with
EN 50242;
2) Programme data obtained in conformity with European standard
EN 50242. Values may vary in relation to usage, e.g.: different loads,
water temperatures - above or below 15° C - as well as water
hardness and power supply voltage, etc.
Programme ON/OFF selector knob
First press and release the selector knob to access it,
and then turn it to select the desired programme;
the dishwasher switches on.
To switch off the dishwasher when the programme
has finished, turn the selector knob to off.
Start button
Press to start the wash cycle and keep pressed until
an acoustic signal confirms the start of the wash
cycle. The display shows the approximate duration
of the wash cycle.
Note:
the light above the start button blinks during
the wash cycle.
The light stops blinking and remains alight to indicate
the cycle has ended (“End” on the display) or has
been interrupted due to a fault (“E1, E2....” on the
display).
Indicators
Options
Programme chart
Detergent
Consumption
2)
Programmes Loading instructions
A B Litres kWh Minutes
P1
Pre-Rinse cold
Crockery to be washed later. - - 6.0 0.02 15
P2
Rapid 30 min 45°C
Lightly soiled crockery with no dried-on
food.
X - 13.0 0.80 45
P3
Bio
1)
55°C
Normally soiled crockery. X - 15.0 1.08 180
P4
Normal 65°C
Normally or heavily soiled crockery. X - 17.0 1.28 90
P5
Intensive 70°C
Recommended programme for heavily
soiled crockery, especially suitable for pans
and saucepans.
X X 20.0 1.60 110
49696031GB.fm Page 1 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Large compartment
A
Small compartment
B
Mechanical indicator lamp
C
.
Electric indicator on control panel (if provided).
On models with water softener system
only.
Mechanical indicator lamp
D
.
Electric indicator on control panel
(if provided).
Refer to the dishwasher loading instructions.
Press and turn the selector knob to select the desired programme and
switch on the appliance.
If necessary (and if provided).
The corresponding indicator lamp lights up.
“Cancel”
Press and hold the “Start” button
until the indicator lamp stops
blinking and stays on.
Press and hold the “Start” button
for 10 seconds. “P0” will appear on
the display and the programme will
stop.
“Change programme in
progress”
Press and hold the “Start” button
until the indicator lamp stops blinking
and stays on.
Select and start the programme as
described previously.
- Only open the dishwasher if
necessary (Warning: beware of
hot steam).
- If the appliance is switched off
during a wash cycle, when
switched on again it will resume
the cycle from where it was
interrupted.
To switch off the dishwasher turn the selector knob to off.
All the indicator lamps and the display switch off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
Open the door
How to fill the
detergent dispenser
AB
C
Check the rinse aid level
Check the
regeneration salt level
D
Load the racks
Close the door,
select a programme
Select
additional options
Turn on the water tap
Press the Start button
to start the programme
(during the cycle the
Start indicator blinks)
Wash cycle
Switch off the appliance
Turn off the water
tap, unload the racks
49696031GB.fm Page 2 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
Dishwasher loading instructions and racks provided
Upper rack:
depending on the model
Cup holders (A):
Depending on the position, up or down.
Place the glasses in the middle and to
the right, dishes to the left, under the
cup holder grids.
Place long and narrow utensils
(carving forks, knives) on the
bottom of the rack, not crosswise,
with the sharp ends facing towards
the appliance.
Cutlery basket supports (B):
Raised or lowered, depending on the
position.
Vertical adjustment of
basket (also with basket
loaded):
Pull upwards to the first or second
catch to raise the basket.
Pull the side release lever to lower the
basket.
The rack must be level on both
sides.
Lower rack:
With tilting plate holders.
Cutlery basket:
It is equipped with grill elements (
C
) to
keep the cultery separated. It can be
divided into two parts, which is handy
for half-load washes or when there are
just a few pieces of cultery to be
washed.
Objects that can cause injuries
must be arranged in the rack with
tips facing downwards.
Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a
dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed),
silver cutlery.
ABAB
Release lever
CC
C
C
49696031GB.fm Page 3 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem (* see
also the corresponding chapter in the user instructions).
Problem Cause Remedy
The appliance is not
working
• No water supply. • Open the tap.
• The appliance does not load sufficient
water.
• Clean the water supply tap filter.
• Ensure there are no kinks in the water hose.
• There is a power failure. • Insert the plug into the mains socket.
•Open the door.
•Close the door.
• Check the domestic circuit fuse.
If crockery is not
perfectly dry
• Insufficient rinse aid. •Increase dosage *.
• Residual water in cavities. • Load crockery at an angle.
If crockery is not
perfectly clean
• The water jet does not reach the
crockery.
• Arrange crockery so that items do not touch each other.
Load crockery upside down.
• Insufficient detergent. • Follow recommended detergent dosage.
• Unsuitable programme. • Select a more intense wash cycle.
• Spray arms blocked. • The spray arms must be able to turn freely.
• Spray arm nozzles clogged. • Remove any impurities obstructing the water flow *.
• Incorrect detergent/detergent too old. • Use a good quality detergent.
Sandy or grainy
residues
• Clogged filters. • Check filters regularly/if necessary clean *.
• Filters incorrectly assembled. • Insert the filter correctly *.
Colour of plastic parts
faded
• Tomato/carrot juice,... • Depending on the material, if necessary use a
detergent with a greater whitening power.
Deposits on crockery
•removable • Streaks on the crockery/glasses. • Reduce the rinse aid dosage *.
• Layer of salt on crockery/glasses. • Close the salt container lid properly *.
• not removable • Insufficient water softening, calcium
deposits.
• Change water hardness setting, if necessary add salt *.
Opaque glasses/
glasses not sparkling
• Cannot be washed in the dishwasher. • Use suitable glasses.
Rust on cutlery
• Not made of stainless steel. •Use suitable cutlery.
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water
supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, take note of the following:
• The nature of the fault.
• The appliance type and model.
• The service code (the number indicated on the adhesive rating plate)
inside the door on the right-hand side.
49696031GB.fm Page 4 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
/