DELTA DORE TYXAL+ DMBE Installation guide

Brand: DELTA DORE

Model: TYXAL+ DMBE

Type: Installation guide

www.deltadore.com

2xLS 14500 - 3.6 V / 5.2 Ah - Lithium

Consumption stand-by : 14 µA

Consumption : 26 mA max

X3D alarm : [868 - 868.6] MHz

et [868.7 - 869.2] MHz

100 m Ý 300m

Maximum power radio < 10 mW,

receiver category: 2

-10°C / +70°C

-20°C / +60°C

IP 55

75%

56 x 235 x 128mm

Important

product information (¸)

520 gr.

Instructions

Important

Product

Informations

Contents

DMBE TYXAL +

Installaon guide

* Up to 10 years valid under the conditions of use speciﬁ ed in the installation instructions and

the General Conditions of Sale

- 2 - - 3 -

Do not direct the lower detection zone towards

reﬂ ecting surfaces (puddle, window, etc.).

Do not direct the detector towards moving objects

(leaves, bushes, ﬂ ags, etc.).

N°1

N°6

N°4

N°3

N°2

N°5

N°7

DMBE TYXAL+ is a passive infrared motion detector, de-

signed to detect the infrared radiation emitted by human

bodies.

This motion detector aims to protect the outside of a

building by detecting intrusions prior to penetration into

the premises.

As soon as a presence is detected, it raises the alarm.

• Associated to a control unit:

- alarm signal.

- pre-alarm signal: as soon as a person enters the

protected zone, a sound and visual signal (outdoor siren)

warns you of the imminent alarm.

For optimal operation, please comply with the following recommendations:

In the event of non-compliance, the product may present malfunctions or

may not function optimally.

N°1

N°6

N°4

N°3

N°2

N°5

N°7

Installation height: between 0.8 m and 1.2 m

Install the motion detector vertically, with its

high detection zones parallel to the ground.

If the detector is installed at an angle,

detection reliability may be compromised.

Install the motion detector vertically, with

both high and low detection zones parallel

to the wall.

To make sure the device functions properly,

attach the motion detector to the wall.

Read the entire guide before starting

to install the device.

Do not install close to a heat pump or heat

evacuation outlet (dryer, etc.).

Note

This product detects temperature differences between moving and background targets within the

detection zone.

If the target remains motionless, the motion detector cannot detect it. This may affect the detec-

tor's maximum detection range.

2. Location

1. Presentation 2. Location

EN EN

- 4 - - 5 -

Ê Ë

Open the base's card slot.

Plug the battery cable into the card

connector.

Set the product you want to associate

to ‘pending association’, then press the

association button on the board.

Ì ¹

Change settings if necessary.

(See inclination, range and function

settings)

Connector

Close the product up.

Close the card slot.

Screw the base onto the rear mount.

Do not touch the lenses.

Remove the ﬁ xing screw from

the top cover and withdraw

the cover.

Remove the ﬁ xing screws

from the rear mount.

Remove the rear mount.

By moving it away from the base.

By sliding it upwards.

Do not touch the mirrors.

Attach the rear mount (foam

pad facing down) using the

assembly jig included in the

assembly pack.

Assembly

jig

3. Mounting 4. Activation

EN EN

Association

button

- 6 - - 7 -

Note:

Settings for the

lower left- and

right-hand areas

can be changed

independently.

Example: the right-hand lens on D and the

left-hand lens on C.

If an obstacle cuts through the beams along the wall, these

beams can be inclined horizontally towards the front, up to 3

degrees, to avoid this obstacle.

3°

0°

To trigger the detection process, both beams on a same side must be cut

through simultaneously.

If you change the beams' inclination:

• The high and low beams of a same side are to be conﬁ gured identi-

cally (same angle).

• Sensitivity must be set to HI (high). See section on sensitivity settings.

To change these settings:

Unblock the three stops on

each side of the lens mount

by sliding in a screwdriver

blade, as shown below.

Gently separate the lens

mount and front top cover.

Principle:

Remove the ﬁ xing screw

from the top cover and

withdraw the cover.

Move the lens frontwards to tilt the

beam 3°

(distance from the wall),

Check that the lateral notch at the

rear of the lens mount is cleared

(empty).

Ë Ì

After having selected the detection zone's settings, return the

lens mount to the top cover before aligning the three stops (A,

B and C) on each side of the lens mount with the three notches

(A', B' and C') on the front top cover.

By selecting the 3-degree beam inclination,

the detection zone starts at 0.60 m from the

wall and extends 12 m.

3°

~ 0,6 m

12 m

0°

Set the range by gently sliding the lens in its

compartment.

The high beam will always remain parallel to the ground.

The lower beam can be directed as shown below.

The range is limited by the lower beam's angle, as high and low beams must be cut through simulta-

neously to activate the motion detector.

Principle:

To change these settings:

Gently separate the lens mount

and front top cover.

(See "Setting beam inclination")

Make sure the lens stays parallel to the

mount.

Do not bend the lens.

5. Beam inclination settings 6. Detector range settings

If the high beam alone is cut through:

No detection

If the high and low beams are cut th-

rough: Detection

If the low beam alone is cut through:

No detection

EN EN

- 8 - - 9 -

Select the desired position (A, B, C or D).

Position A (12 m)

Position B (8 m)

Position C (5 m)

Position D (2m)

Return the lens mount to the top cover.

(See "Setting beam inclination")

Put the top cover in its place and conduct a detection test.

(See "Detection test").

You can use the LED light to determine the detection zones

(See section "Function settings" Switch 3).

If the detection zones are not suitable, readjust the range by sliding the lens to another position on

the LENS MOUNT.

SENS

The sensitivity can be set to 3 different positions:

• L(low),

• M (medium),

• H (high),

The chosen position will depend on environmental condi-

tions.

Detection sensitivity settings

We recommend that you set the sensitivity level to

H (high):

• When the detection beams were tilted horizontally.

• When higher sensitivity is required towards the end of

the detection zone (12 m).

L (low):

• When the device is installed in a mediocre location

(bad conditions).

• When there is a high risk of faulty detection.

DIP switch settings

• NORM. position

Important: The switch must be in this position during

normal operation.

(The LED stays off to save battery life).

• Detection TEST position

The LED lights up when the detector's beam is cut

through.

(Battery's energy-saving timer)

For optimal operation, leave switch 2 on the following

position:

• Position 120 s. Do not change this setting.

(Detection LED)

• OFF position: LED is switched off

• ON position: LED is switched on if the detector is

activated.

(Battery life is reduced).

Switch 1

Switch 2

Switch 3

6. Detector range settings 7. Function settings

* Installation height = 1 m.

Standard environment = T° of 20°C with

no direct sunlight.

** The maximum range may be inﬂuenced

by ambient thermal conditions.

The lower beam can be set to control the range according to the table below.

EN EN

Position

Standard

range *(m)

Maximum

range ** (m)

A 12 10 - 15

B 8 6 - 10

C 5 4 - 6

D 2 1.5 - 3

- 10 - - 11 -

Check the device functions properly by conducting a detection test.

LED ON

LED OFF

Ê Ë

Position switch 1 to

TEST mode (ON).

Put the top cover in its place.

Check the LED is switched off when there is no movement in the

detection zone.

Both beams are to detect a movement for the alarm to be trigge-

red.

Once the test is ﬁ nished, position switch

1 to NORM mode (OFF), then close the

unit.

• Association with an alarm system

• Pre-alarm

• Selection of triggering method

• Test

Read system installati-

on guide

Problem Probable cause Solution

The LED ﬂ ashes

continuously.

Incorrect power supply.

Establish a power supply

set between 3 and 9 Vdc for the battery.

Triggered

detection without any

objects moving

The motion detector was not installed

perpendicularly to the ground.

Install the motion detector

correctly.

A reﬂ ecting object is located within the

detection zone.

Eliminate all reﬂ ecting surfaces from the

detection zone.

The lower beam is longer than expected. Check and readjust the detection beam.

The lower detection beam is exposed to

direct sun rays or to car headlights.

Readjust the detection beam

so it is no longer exposed to direct light

sources.

Presence of a heat source (heating de-

vice, etc.) in the detection zone that may

cause the temperature to change.

Readjust the detection beam or eliminate

the heat source in the detection zone.

An object is moving (washing hung up on

a line, plants, etc.).

Readjust the detection beam or remove

moving objects.

In the event of heavy rain, water may pour

through the detection zone (overﬂ owing

gutter, roof/terrace/balcony drainage,

etc. )

Readjust the detection beam

so it is no longer directly exposed to the

ﬂ owing water.

Occasionally no

detection.

Occasionally no detection. Readjust the detection beam correctly.

Sensitivity is set to L (low).

Readjust the sensitivity level to M (medi-

um) or H (high).

Occasionally no

detection when a

detection test is

conducted

The detection test switch is set to OFF.

(Battery's energy-saving timer is activa-

ted).

Flick the detection test mode switch to ON.

(See "Detection test").

8. Detection test 10. Battery replacement

9. Operation with an alarm system

11. Troubleshooting

Detection

No detection

EN EN

The LED ﬂ ashes continuously, the battery is dead. Before opening the unit, the alarm control unit must be

in Maintenance mode (refer to system installation guide).

Ê Ë Ì ¹

DELTA DORE TYXAL+ DMBE Installation guide

DELTA DORE TYXAL+ DMBE Installation guide

DELTA DORE TYXAL+ DMBE Installation guide

Related papers

Other documents