Page is loading ...
MODELO:
CE22672
MANUAL DEL USUARIO
EXPRIMIDOR DE CITRICOS
MODEL:
CE22672
INSTRUCTION MANUAL
CITRUS JUICER
1
1
3.CARE AND CLEANING
(1) ALWAYS UNPLUG THE UNIT BEFORE CLEANING OR WHEN NOT IN
USE.
(2) RINSE THE STRAINER/REAMER IMMEDIATELY AFTER USE. USE A
BRISTLE BRUSH TO REMOVE FINE PULP THAT MAY REMAIN.
(3) USE HOT, SUDSY WATER TO WASH THE COVER REAMER,
STRAINER AND PITCHER OR PLACE IN THE "TOP RACK ONLY" OF A
DISHWASHER. WIPE THE BASE CLEAN WITH A DAMP CLOTH.
IMPORTANT:
IF THE SUPPLY CORD OF THIS APPLIANCE IS DAMAGED, IT MUST
ONLY BE REPLACED BY A REPAIR SHOP APPOINTED BY THE
MANUFACTURER, BECAUSE SPECIAL PURPOSE TOOLS ARE
REQUIRED.
OPERATION TIMES:10S ON, 10S OFF AND OPERATE NAT MORE THAN
10 TIMES.
4.ASSEMBLE AS SHOWN
COVER
BIG REAMER
SMALL REAMER
STRAINER
ADJUSTMENT
PITCHER
BASE
FIGURE A
1
1
3.CARE AND CLEANING
(1) ALWAYS UNPLUG THE UNIT BEFORE CLEANING OR WHEN NOT IN
USE.
(2) RINSE THE STRAINER/REAMER IMMEDIATELY AFTER USE. USE A
BRISTLE BRUSH TO REMOVE FINE PULP THAT MAY REMAIN.
(3) USE HOT, SUDSY WATER TO WASH THE COVER REAMER,
STRAINER AND PITCHER OR PLACE IN THE "TOP RACK ONLY" OF A
DISHWASHER. WIPE THE BASE CLEAN WITH A DAMP CLOTH.
IMPORTANT:
IF THE SUPPLY CORD OF THIS APPLIANCE IS DAMAGED, IT MUST
ONLY BE REPLACED BY A REPAIR SHOP APPOINTED BY THE
MANUFACTURER, BECAUSE SPECIAL PURPOSE TOOLS ARE
REQUIRED.
OPERATION TIMES:10S ON, 10S OFF AND OPERATE NAT MORE THAN
10 TIMES.
4.ASSEMBLE AS SHOWN
COVER
BIG REAMER
SMALL REAMER
STRAINER
ADJUSTMENT
PITCHER
BASE
FIGURE A
ASSEMBLE INSTRUCTIONS
INTRUCCIONES DE ENSAMBLE
TAPA PROTECTORA
EXPRIMIDOR GRANDE
EXPRIMIDOR PEQUEÑO
AJUSTADOR
COLADOR
TAZON
BASE
2
2
3
3
MODELO:
CE22672
MANUAL DEL USUARIO
EXPRIMIDOR DE CITRICOS
MODEL:
CE22672
INSTRUCTION MANUAL
CITRUS JUICER
1
1
3.CARE AND CLEANING
(1) ALWAYS UNPLUG THE UNIT BEFORE CLEANING OR WHEN NOT IN
USE.
(2) RINSE THE STRAINER/REAMER IMMEDIATELY AFTER USE. USE A
BRISTLE BRUSH TO REMOVE FINE PULP THAT MAY REMAIN.
(3) USE HOT, SUDSY WATER TO WASH THE COVER REAMER,
STRAINER AND PITCHER OR PLACE IN THE "TOP RACK ONLY" OF A
DISHWASHER. WIPE THE BASE CLEAN WITH A DAMP CLOTH.
IMPORTANT:
IF THE SUPPLY CORD OF THIS APPLIANCE IS DAMAGED, IT MUST
ONLY BE REPLACED BY A REPAIR SHOP APPOINTED BY THE
MANUFACTURER, BECAUSE SPECIAL PURPOSE TOOLS ARE
REQUIRED.
OPERATION TIMES:10S ON, 10S OFF AND OPERATE NAT MORE THAN
10 TIMES.
4.ASSEMBLE AS SHOWN
COVER
BIG REAMER
SMALL REAMER
STRAINER
ADJUSTMENT
PITCHER
BASE
FIGURE A
1
1
3.CARE AND CLEANING
(1) ALWAYS UNPLUG THE UNIT BEFORE CLEANING OR WHEN NOT IN
USE.
(2) RINSE THE STRAINER/REAMER IMMEDIATELY AFTER USE. USE A
BRISTLE BRUSH TO REMOVE FINE PULP THAT MAY REMAIN.
(3) USE HOT, SUDSY WATER TO WASH THE COVER REAMER,
STRAINER AND PITCHER OR PLACE IN THE "TOP RACK ONLY" OF A
DISHWASHER. WIPE THE BASE CLEAN WITH A DAMP CLOTH.
IMPORTANT:
IF THE SUPPLY CORD OF THIS APPLIANCE IS DAMAGED, IT MUST
ONLY BE REPLACED BY A REPAIR SHOP APPOINTED BY THE
MANUFACTURER, BECAUSE SPECIAL PURPOSE TOOLS ARE
REQUIRED.
OPERATION TIMES:10S ON, 10S OFF AND OPERATE NAT MORE THAN
10 TIMES.
4.ASSEMBLE AS SHOWN
COVER
BIG REAMER
SMALL REAMER
STRAINER
ADJUSTMENT
PITCHER
BASE
FIGURE A
ASSEMBLE INSTRUCTIONS
INTRUCCIONES DE ENSAMBLE
TAPA PROTECTORA
EXPRIMIDOR GRANDE
EXPRIMIDOR PEQUEÑO
AJUSTADOR
COLADOR
TAZON
BASE
2
2
3
3
/
