Pentair Illuminator PG2000 User manual

Brand: Pentair

Model: Illuminator PG2000

Category: Infrared bulbs

Type: User manual

This manual is also suitable for

PG2000

Pentair Illuminator PG2000 is a powerful and versatile lighting solution for pools and spas. With its 150-watt metal-halide lamp and 6000-hour lamp life, the PG2000 provides bright and long-lasting illumination. The unit's high-strength plastic construction ensures durability, while its compact size makes it easy to install. The PG2000 can be operated manually or with a variety of control systems, making it a versatile choice for any pool or spa application.

Rev. C 5-15-09 1 P/N 840263

PG2000

Owner's Manual

Pentair Water Pool and Spa, Inc.

1620 Hawkins Ave., Sanford, NC 27330 • (800) 831-7133 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 • (805) 553-5000

Visit us on the Internet at: www.pentairpool.com or www.staritepool.com

Specifications:

Electrical: 120 VAC 60 Hz

Operating load: 2 amps

Material: High Strength Plastic

Weight: 20 lbs.

Lamp: 150 Watt Metal-Halide

Lamp Life: 6000 hours

Restrike time: 2-3 minutes

P/N 840263 2 Rev. C 5-15-09

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS BEFORE OPERATING SYSTEM

Operating the PG2000

Refer to the toggle switch position diagram below for the appropriate switch positions for your particular installation.

The switches are located on the lower right side of the unit. The PG2000

should always operate in manual mode no

matter what type of control system is installed.

NOTE

When cycling system off, then back on, it may take up to 3-4 minutes before the lamp "restrikes" or comes

back on. The lamp must cool down before restriking. All metal halide lamps have this characteristic and this is

a normal function of the PG2000

CAUTION

PG2000

Illuminator must have good ventilation to operate properly.

Blockage of air flow or air intake will shorten the bulb life and could

damage the unit. Make sure foliage; grass, groundcover, yard debris, etc.

is kept clear of intake vents on back of the unit in order to allow for proper

air flow. Do not install PG2000

Illuminator in an underground utility box or

similar appliance. Damage to the unit due to blocked air vents or poor

ventilation will void the warranty.

Replacing the Bulb.

1. Turn power to unit off.

WARNING

Turn off power before changing bulb. Failure to turn off power

may lead to severe electrical shock, which can result in death

or severe injury.

2. Remove two screws securing outer body and lift outer body

straight up.

WARNING

Bulb socket, and reflector are extremely hot during and following operation.

Allow sufficient time for cooling before touching them, or you may suffer

severe burns.

3. Remove screws (3) at bottom of socket bracket, (see Figure 1.)

and separate socket bracket assembly from reflector.

Remove bulb from socket and insert new bulb. Be sure not to

touch the glass of the bulb.

CAUTION

Do not touch the bulb with your bare fingers - fingerprints can actually cause

the bulb to overheat and crack. Handle the bulb using sheath provided in

packaging.

4. Reassemble socket bracket and make sure bulb is centered in

reflector.

5. Replace outer body and secure with two screws.

COLOR

POWER

RF2000 WIRELESS CONTROL

COLOR

POWER

REMOTE SWITCH CONTROL

COLOR

POWER

MANUAL CONTROL

TOGGLE SWITCH POSITIONS

COLOR

OFF

POWER

OFF

Figure 1.

Remove

Screws

Intake

Vents

Rev. C 5-15-09 3 P/N 840263

PG2000

Synchronization Procedures with SAm

light

Listed below are the procedures to follow if you have a SAm

underwater color light installed in your pool or spa and wish

to synchronize your fiber optics with SAm

NOTE

There may be slight color variations between the SAm

and PG2000

depending on the application. These variations are caused by

differences in initial light intensity and attenuation of the water and/or reflective surfaces (i.e. pool wall coloring).

In order for instructions to work you must have P/N 840242 – 7 Color, Electronic Synchronized PG2000

(all other part numbers must use visual synchronization method)

Synchronization Start Conditions

1. SAm

is ON and colorwheel is stopped on ANY color (including white).

2. PG2000

power is ON and the colorwheel is OFF.

Synchronization Procedure

1. Simultaneously toggle SAm

OFF/ON and turn the PG2000

colorwheel ON.

2. Allow about 1½ minutes for colors to synchronize. Enjoy!

3. To stop both lights on the same color, simultaneously toggle SAm

OFF/ON and turn the PG2000

colorwheel OFF.

Visual Synchronization Method (for use with P/N 840241 only)

1. Turn SAm

ON, colorwheel is stopped on ANY color (including white).

2. Turn PG2000

ON and colorwheel ON.

3. When PG2000

transitions between purple and magenta toggle SAm

OFF/ON.

4. To stop both lights on the same color, simultaneously toggle SAm

off and on while turning the PG2000

colorwheel off.

Troubleshooting

If the PG2000

does not come on at all…

• Make sure the power switch is on (see switch position diagram). On Auto Remote Control (Compool

/Jandy

) make

sure the proper auxiliary is turned on. The PG2000

should always operate in manual mode no matter what type of

control system is installed.

• Check that the circuit breaker is not tripped.

• Check the incoming voltage at the PG2000

to verify power supply.

• Check the fuse(es) inside the unit. Replace if fuse is open.

If there is no light…

• Check that the bulb is in place securely in the socket.

• If you can hear the fan running the lamp has probably failed. Replace lamp.

If the fan runs, but the light cycles on and off…

• Check the vents of obstructions. There must be adequate air flow or PG2000

will overheat and begin to cycle.

• If the unit is operating in direct sunlight during a very hot day it may exceed the recommended operating temperature and

cycle on and off. This protects the end of the fiber optic cables from damage and is normal.

If the light comes on, but the fan is not running…

• Turn off PG2000

immediately and check for obstructions in the fan!

• DO NOT continue to operate PG2000

without the fan running! The excess heat can damage the fiber optic cable.

Colors do not change….

• Make sure the colorwheel power is on. On Auto Control (Compool

/Jandy

) make sure the proper auxiliary is turned on.

• Remove the body and check the colorwheel for obstructions or debris that might be interfering with the rotation of the

color wheel.

TROUBLESHOOTING NOTE:

If none of the above suggestions solve your particular problem, contact your pool contractor, or Pentair Water Pool and Spa, Inc.'s Customer

Service hotline at: 800-831-7133, Monday through Friday 7:30 a.m. – 4:30 p.m.

P/N 840263 4 Rev. C 5-15-09

Pentair Water Pool and Spa, Inc.

1620 Hawkins Ave., Sanford, NC 27330 • (800) 831-7133 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 831-7133 • (805) 553-5000

SAVE THESE INSTRUCTIONS

This document is subject to change without notice.

Trademarks and Disclaimers: PG2000

, SAm

, Compool

and Pentair Water Pool and Spa

are trademarks and/or registered trademarks of Pentair Water Pool

and Spa, Inc. and/or its affiliated companies in the United States and/or other counties. Unless noted, names and brands of others that may be used in this

document are not used to indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair Water Pool and Spa, Inc.

Those names and brands may be the trademarks or registered trademarks of those parties or others.

Protected by one or more of the following U.S. Patents and all corresponding foreign counterparts: U.S. Pat. No. 5,802,227; 5,825,954; 5,680,496; 6,002,216.