Window-type Room Air Conditioner
(Cool)
DB98-24830A(1)
OWNER’S
INSTRUCTIONS
AWT17XSHDA
AWT18XSHDE
AW24XSHEB
E-2
The manufacturer does not assume responsibility for accidents or injury
caused by an incorrectly installed air conditioner. If you are unsure about
installation, contact an installation specialist.
CCC
CCC
AAA
AAA
UUU
UUU
TTT
TTT
III
III
OOO
OOO
NNN
NNN
The following safety precautions must be taken when using your air conditioner.
Safety Precautions
1 The unit must be plugged into an independent circuit.
The air conditioner must be installed in accordance with national wiring regulations and
safety regulations wherever applicable.
2 Some installation locations may require installation of a short circuit breaker or grounding.
4 MAKE sure that the unit is correctly ventilated at all times ;
do NOT place clothing or other materials over it.
5 NEVER spill any kind of liquid into the unit. Should this happen, unplug the unit and contact
an authorized service center.
6 Do NOT insert anything between the air outlet blades because the inner fan may be damaged
and could cause injury. Keep children away from the unit.
7 Do NOT place any obstacles in front of the unit.
8 Users of this product are cautioned not to attempt repairs.
Instead, they are requested to directly contact a designated service center or the outlet
at which the product was purchased.
9 Do not use an extension cord with this product.
10 The appliance is not intended for use by young children without supervision ;
young children should be supervised to ensure that they do not play with the appliance.
11 Never store or ship the air conditioner upside down or sideways to avoid damage to the
compressor.
12 Max current is measured according to IEC standard for safety
and current is measured according to ISO standard for energy efficiency.
3 If the supply cord is damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
E-6
Getting Started
IMPORTANT NOTE
You have just purchased a Samsung window-type room air conditioner which should be installed
following your installation manual.
Your Owner's Instructions contain much valuable information on using your air conditioner.
Please take the time to read them as they will help you take full advantage of the unit's features.
The booklet is organized as follows.
The following figures are shown on pages 4 and 5:
- Description of Each Component
- Remote control (buttons)
They will help you find the buttons and understand the symbols displayed.
In the manual, you will find a series of step-by-step procedures for each function
available.
The illustrations in the step-by-step procedures use four different symbols:
PRESS PUSH
E-7
Inserting the Remote Control Batteries
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities :
+ on the battery with + on the remote control.
- on the battery with - on the remote control.
1
2
Close the cover by sliding it back until it clicks into place.
3
Use two AAA, LR03 1.5V batteries.
Do not use old batteries or different kinds of batteries together.
Batteries may be completely discharged after 12 months, even
if they have not actually been used.
You must insert or replace the remote control batteries when :
You purchase the air conditioner
The remote control does not work correctly
E-8
This chapter indicates how to operate and program
your air conditioner with the control panel on the unit.
UUU
UUU
sss
sss
iii
iii
nnn
nnn
ggg
ggg
ttt
ttt
hhh
hhh
eee
eee
CCC
CCC
ooo
ooo
nnn
nnn
ttt
ttt
rrr
rrr
ooo
ooo
lll
lll
PPP
PPP
aaa
aaa
nnn
nnn
eee
eee
lll
lll
ooo
ooo
nnn
nnn
ttt
ttt
hhh
hhh
eee
eee
UUU
UUU
nnn
nnn
iii
iii
ttt
ttt
E-16
M
o
e
d
T
i
m
e
r
S
e
t
/
C
a
n
c
e
l
E
n
e
r
g
y
a
v
ig
S
n
C
This chapter indicates how to operate and program
your air conditioner with the wireless remote control.
UUU
UUU
sss
sss
iii
iii
nnn
nnn
ggg
ggg
ttt
ttt
hhh
hhh
eee
eee
WWW
WWW
iii
iii
rrr
rrr
eee
eee
lll
lll
eee
eee
sss
sss
sss
sss
RRR
RRR
eee
eee
mmm
mmm
ooo
ooo
ttt
ttt
eee
eee
CCC
CCC
ooo
ooo
nnn
nnn
ttt
ttt
rrr
rrr
ooo
ooo
lll
lll
E-17
Cooling Your Room
1
If necessary, press the (On/Off) button.
Result
:
The air conditioner starts up in the Cool mode.
The unit beeps.
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
lt will start up normally after three minutes.
If the is not displayed at the top of the remote control,
press the button on the remote control one or more times until it
appears.
Result: The unit beeps each time you press the button.
The air conditioner runs in the Cool mode.
2
You can change modes at any time.
To adjust the temperature, press the buttons one or more times
until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result:
Each time you press the buttons:
- The temperature is adjusted by 1°C
- The unit beeps
The air conditioner starts cooling, if the room temperature
is higher than the selected temperature.
If the room temperature reaches the set temperature, the
air conditioner stops cooling, but the fan is still operating.
3
Select the Fan Speed by pressing the button one or more
times until the required setting is displayed:
Low
Medium
High
Result
: Each time you press the button, the unit beeps.
4
To control the direction of the air flow, refer to page 23 and 24.
5
You must select the Cool mode if you wish to adjust the:
Cooling temperature
Fan Speed when cooling
Mode
Timer
Set/Cancel
Energy Saving
C
Mode
Timer
Set/Cancel
Energy Saving
C
Mode
Timer
Set/Cancel
Energy Saving
C
Mode
Timer
Set/Cancel
Energy Saving
C
E-18
Airing Your Room
If the atmosphere in your room is stale, you can air the room using
the Fan feature.
1 If necessary, press the (On/Off) button.
Result: The air conditioner starts up in the Cool mode.
The unit beeps.
2 If the is not displayed at the top of the remote control,
press the button on the remote control one or more times until it
appears.
Result
:
The unit beeps each time you press the button.
The air conditioner runs in the Fan mode.
The temperature is set automatically.
You can change modes at any time.
3 Select the Fan Speed by pressing the button one or more times
until the required setting is displayed:
Low
Medium
High
Result
: Each time you press the button, the unit beeps.
4 To control the direction of the air flow, refer to page 23 and 24.
Mode
Timer
Set/Cancel
Energy Saving
Mode
Timer
Set/Cancel
Energy Saving
C
24
Mode
Timer
Set/Cancel
Energy Saving
C
E-19
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can remove
excess humidity without lowering the room temperature too much.
1 If necessary, press the (On/Off) button.
Result
: The air conditioner starts up in the Cool mode.
The unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
Plugged in
Stopped
It will start up normally after three minutes.
2 If the is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result
:
The unit beeps each time you press the button.
The air conditioner runs in the Dry mode.
You can change modes at any time.
3 To adjust the temperature, press the buttons one or more times
until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result
: Each time you press the buttons:
- The temperature is adjusted by 1°C
- The unit beeps
The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4 To control the direction of the air flow, refer to page 23 and 24.
Mode
Timer
Set/Cancel
Energy Saving
C
Mode
Timer
Set/Cancel
Energy Saving
C
Mode
Timer
Set/Cancel
Energy Saving
C
E-
20
Setting the On Timer
If you want to turn on the air conditioner before the timer reaches
the setting time, press the (On/Off) button.
The On Timer enables you to switch on the air conditioner automatically after
a given time. You can select the On Timer only when the air conditioner is off.
You can select the On Timer only when the air conditioner operates in the Cool
or Dry mode.
To set the operating time, press the button one or more times until
the required time is displayed. Possible time is between 1 hour and
24 hours inclusive.
1
Press the (Set/Cancel) button to complete the setting.
Result: The remaining time is displayed.
Blinking of the timer indicator stops.
The air conditioner will switch on automatically when the
counter displayed on the remote control reaches the set time
and disappears the On Timer setting.
You can select the temperature after setting the On Timer mode.
However, you can select Energy Saving mode only in the Cool mode.
2
Press the (Set/Cancel) button.1
To Cancel the On Timer
Mode
Timer
Set/Cancel
Energy Saving
C
88
Mode
Timer
Set/Cancel
Energy Saving
C
88
Mode
Timer
Set/Cancel
Energy Saving
C
3.0
88
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/