ÐÓÊÎÂÎÄÑÒÂÎ ÏÎ ÓÑÒÀÍÎÂÊÅ È
ÈÑÏÎËÜÇÎÂÀÍÈÞ
INSTRUCTION MANUAL
EW 622 K
129 5805 01
GB
RU
- 14 -
TECHNICAL SPECIFICATIONS
DIMENSIONS Height 650 mm
Width 450 mm
Depth 650 mm
POWER SUPPLY VOLTAGE / FREQUENCY 230 V / 50 Hz
TOTAL POWER ABSORBED 2300 W (10 A)
HEATER RATING 1950 W
WATER PRESSURE Minimum 5 N/cm²
Maximum 80 N/cm²
MAXIMUM RECOMMENDED LOAD Cotton, linen 4,5 kg
Synthetics,delicate fabrics 2,0 kg
Wool 1,0 kg
SPIN SPEED 600 rpm
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
Technical specifications ...................................................................................................................... Page 15
Warnings................................................................................................................................................ Page 16
Installation ............................................................................................................................................. Page 17
Unpacking ............................................................................................................................................... Page 17
Water connection .................................................................................................................................... Page 17
Electrical connection ............................................................................................................................... Page 18
Levelling .................................................................................................................................................. Page 18
Positioning............................................................................................................................................... Page 18
Use.......................................................................................................................................................... Page 19
Control panel ........................................................................................................................................... Page 19
Washing hints.......................................................................................................................................... Pages 20-21
Wash programmes .................................................................................................................................. Page 22
Wash code symbols ................................................................................................................................ Page 23
Operating instructions ............................................................................................................................. Page 24
Maintenance .......................................................................................................................................... Page 25
Cleaning the machine.............................................................................................................................. Page 25
Cleaning the pump filter .......................................................................................................................... Page 25
Something not working ?..................................................................................................................... Page 26
CONTENTS
- 15 -
WARNINGS
Use only the recommended quantities of fabric
conditioner.
Pets and small children may climb into washing machi-
nes. Check your appliance each time before use.
You should not attempt to repair the machine yourself.
Repairs carried out by inexperienced or unqualified
persons may cause injury and/or more serious faults to
the machine.
This product should be serviced by an authorized Ser-
vice Center only, and only genuine spare parts should
be used.
You must read the whole of this instruction book
before you use the appliance. Follow the advice
carefully.
Keep the book for future reference. If you sell or give
away the appliance, make sure that the book is passed
to the new owner.
The following warnings are provided in the interest of
overall safety. You must read them before the appliance
is installed or used.
This appliance is designed to be used by adults. Children
should not be allowed to touch the controls or play with
the product.
It is dangerous to modify the specifications of this
appliance in any way.
This appliance is heavy. Care should be taken when
moving it.
All packaging and transit bolts must be removed before
the appliance is used. Serious damage may occur if this
is not done.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or competent
person.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Make sure that the appliance does not stand on its
electrical supply cable.
If the machine is situated on a carpeted floor, please
adjust the feet to ensure that air can circulate freely.
Always unplug the appliance and turn off the water after
use.
Do not overload the appliance.
Only wash fabrics which are designed to be machine
washed. If in doubt, follow the instructions you find on the
label of the item itself.
Make sure that all pockets are empty. Hard, sharp
objects such as coins, safety pins, nails, screws or
stones can cause extensive damage.
Do not machine wash fabrics which are saturated with
petroleum products. If volatile cleaning fluids have been
used, make sure that they are thoroughly removed from
- 16 -
INSTALLATION
Unpacking
The parts protecting the inner components of the
machine during transit are red. They must all be removed
before using your machine for the first time. These
parts and their securing means should be kept in case
the machine has to be transported again.
1. Unpack the appliance. Open the lid of the appliance and
remove the polystyrene wedge which blocks the drum.
Close the lid (fig.1).
2. Tip the appliance backwards. Remove the two screws (A)
with red washers on the base of the washing machine with
the special spanner provided (fig.2).
3. Remove the loosened spacers (C). Stand the appliance
upright again (fig.3).
4. On the back part and with the special spanner, remove
the two red loosened spacers (D) (fig.4).
5. The holes which are now visible must be closed with the
plugs (F) provided with the appliance.
6. Please ensure that these parts have been removed from
the machine and keep them in case of next transport (fig.6).
Be careful : when the machine is installed on carpeted floor,
ensure that the carpet do not obstruct the openings, located
at the base of the machine, which are provided for ventila-
tion.
Fig.1
Fig.2
Fig.4
Fig.3
Fig.5
F
C
D
Fig.6
A
Water connection
Water inlet hose :
Connect the water inlet hose to
a cold water tap with a 3/4" gas
threaded orifice, after having
inserted the rugger sealing
washer with incorporated filter
(supplied with the machine) into
the hose collar. If the water
connection is made onto new
pipes or onto pipes which have
not been used for a long time, it
is advisable to run off a certain amount of water before
connecting the machine. This will avoid foreign matter
blocking the filter placed at the end of the water inlet hose.
Water outlet hose :
Place the curved end of the outlet hose into a drain pipe
having a height between 60 and 80 cm from floor level or
secure it to a sink or bath tub. Make sure that the drain hose
is firmly secured so that it will not slip out or fall down from
its position.
The water should drain freely and, consequently, the drain
hose should not be choked or placed in such a way as to
obstruct the normal water flow. If an extension hose is
required, remember that it might cause a malfunction in the
drain pump, particularly if the extension has a length in
excess of 1 meter or if the diameter of the extension is
smaller than the diameter of the original drain hose.
60 mm
80 mm
If you want to keep the alignment of
your appliance with the adjacent
cupboards, you have the possibility
to cut the crossbar holding the hoses
located at the back of your washing
machine (fig.6).
- 17 -
Electrical connection
Before you fit the plug into the wall socket, check the
following points :
1) The supply voltage of the domestic wiring system does
not fluctuate by more that 10%, plus or minus, from 230 V.
2) The meter, the fuses, the supply line and the wall socket
are suitable to carry the maximum load required by the
machine (2,3 kW).
This appliance complies with the E.E.C. directive
No.87/308 of 2/6/87 relative to radio interference
suppression.
Very important :
The washing machine is provided with a feeding wire
with earth connection: it must be connected to a tap
like tat is provided with a good earth connection.
The manufacturer declines any responsibility where
the previous recommendations are not followed.
Note : the rating plate is situated on the internal side of the
drain filter.
Levelling
It is essential that your machine is
absolutely level. Raise or lower the
front feet of the machine : tighten
the nuts of the feet with an
adjustable wrench.
Also make sure that the machine
does not touch the wall, the
furnitures etc. during the
functioning. This in order to avoid vibrations, noise or
displacements of the appliance during operation.
Positioning
To move your washing machine, put it on its wheels by
turning from the right to the left the special lever situated at
the bottom of the machine. Once the machine placed at the
chosen place, bring back the lever to its initial original
position.
- 18 -
Never turn the programm selector when the appliance is working.
The detergent dispenser
1 prewash compartment
(aI)
2 main wash compartment
(bII)
3 softener compartment
(c )
Pour the necessary quantities of products in the appropriate
compartments.
Control panel
1. ON/OFF pushbutton " "
Press the ON/OFF pushbutton, the programm starts. The
control lamp lights on.
2. Control lamp
The control lamp lights on when the appliance is working
(ON/OFF pushbutton " " pressed). It lights off when the
ON/OFF pushbutton ( ) is pressed out.
3. Half load pushbutton " "
If pressed in at the beginning of a wash programme, it
allows to wash economically small quantities of laundry, up
to 2,0 kg of resistant laundry (cotton-linen). This pushbutton
is without effect on the synthetic and wool programmes.
4. Programme selector
It enables to select the most adapted programme to the
nature and degrees of soil of your laundry.
Turn the programme selector clockwise to select the
chosen programme.
The programme selector indicates each programme phase
as it takes place.
At the end of the programme, the appliance stops
automatically on a position off "I" or on the position "'rinse
hold".
Never turn the programme selector
anticlockwise.
5. Temperature knob
It enables to choose the most adapted temperature
between cold ( ) and 90°C. Choose the temperature
which corresponds to the chosen programme, with the
help of the indications of the programme table, according
to the fibers and the fastness of the colours.
1
2
EW 622 K
5
A
B
C
H
J
F
D
R
M
P
N
50°
40°
90°
70°
60°
80°
30°
3
4
1
2
3
G
K
L
E
USE
- 19 -
Washing hints
You are advised not to leave your laundry too long, especially
when damp. Damp laundry produces moult and unpleasant
smells.
Moult stains cannot be removed.
Sort your laundry.
Study carefully the chart in this booklet explaining the
symbols used on clothes labels (see page 9).
The following points are particularly important :
a line under the bowl means that the garment cannot be
washed using programmes for resistant fabrics such as
cotton and linen;
do not mix coloured garments with whites;
anticrease materials like polyester/cotton should be treated
as synthetics;
non-resistant fabrics like acrylic and most curtain materials
should be treated as delicate fabrics;
the wool programme is designed specifically for pure new
wool. Other types of wool and wool mixtures may shrink or
felt if machine-washed.
Woollen garments should be spun briefly immediately after
washing.
Pre-wash
Pre-wash is not normally necessary. Your new washing
machine combined with modern detergents will give perfect
washing results without pre-wash, thus saving energy,
time, water and detergent.
However, when the laundry is particularly dirty (for example
if you have to wash mechanics' overalls or butchers'
aprons), you are advised to use pre-wash with a biological
detergent.
Temperatures
We suggest that white cotton and linen, if it is not excessively
soiled, can be washed at 60° instead of 90°C. There should
be no reduction in performance, but there will be an energy
saving of approximately 30%.
The same applies to a lesser extent to fast coloured
garments.
They usually require a temperature of 60°C but if they are
not excessively dirty, you will have satisfactory results at
40°C.
Garments with non-fast colours should not be washed at
temperatures above 40°C. If fast and non-fast colours are
washed together, they should be treated as non-fast colours
and therefore the temperature should not exceed 40°C.
Resistant white and coloured synthetics can normally be
washed at 60°C but also in this case 40°C is sufficient if the
laundry is not excessively dirty.
Delicate synthetics, synthetics with non-fast colours and
woollen garments must never be washed above 40°C.
As you already know, your washing machine can also
wash with cold water. However, it must be remembered
that the detergents currently on the market have not
been designed for cold washes and that in winter, when
the water is very cold, they may not dissolve adequately.
We suggest the use of liquid detergents.
How much laundry can be washed in one load?
Strictly speaking you should always weigh your laundry.
The drum will take a maximum of 4,5 kg of cotton and
linen. For synthetics and delicate fabrics, the maximum
load is 2,0 kg and for wool, 1 kg.
As weighing can be complicated, we suggest you
estimate the weight according to how full the drum is:
cotton and linen : drum full not too tighty packed
resistant synthetics : no more than 2/3 of the drum
delicate fabrics and wool : no more than 1/2 of the
drum.
Before placing the laundry in the machine:
mend all tears, holes and ladders;
secure loose buttons and close poppers and zips;
do not wash frayed garments - mend hems before
washing;
remove all small objects from pockets. Nails, pins, clips
and similar objects can seriously damage your washing
machine and laundry;
remove curtain hooks;
wash coloured garments and in particular those with
non-fast colours separately when washing for the first
time. They are likely to lose colour the first time they are
washed.
treat obstinate stains such as grass, rust, tar, paint, ink
etc. with a stain remover before washing.
To remove paint stains, for example, use a volatile
substance such as turpentine: in this case, you should
wait for it to dry completely before washing.
The manufacturer of your washing machine is not
responsible for any damage deriving from the use of
volatile, inflammable or toxic substances.
At the end of the washing
Damp laundry should be dried as soon as possible after
finishing the wash.
Knitwear and woollens should be dried flat away from
direct sunlight.
- 20 -
Detergents and additives
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid waste
and protect the environment. Although biodegradable,
detergents contain substances which in large quantities
can damage the delicate ecological balance of nature.
Always use good quality detergents suitable for use
in washing machines.
Follow the indications given by the detergent manufactu-
rer according to the weight of laundry, the degree of soil
and the hardness of the water in your area; if you do not
know how hard it is, ask your local Water Authority.
Powder detergents.
The washing powder should be placed in the appropriate
compartments of the dispenser drawer before starting the
programme. Special detergents are availaible for coloured
and delicate fabrics and for wool.
<<Concentrated>> powder detergents
Pour the concentrated powder detergent into the main
wash (bII) compartment.
Avoid selecting programmes including prewash when
concentrated detergents are used.
LIquid detergents
If you wish use liquid detergent, please get a ball dispen-
ser and put it directly in the drum of your washing
machine.
Liquid detergents can be used instead of powder
detergents particularly for lightly soiled laundry and for
medium or low temperature washing programmes, while
it is better to use a powder detergent for high temperature
washing programmes.
Liquid additives
Any liquid additives for softening the laundry must be
poured into the compartment c of the detergent dispen-
ser drawer before starting the programme.
The addition of water softener is particularly useful when
drying the clothes in a tumble dryer after washing to avoid
a static charge.
Level Characteristic French degrees
°dH m mol °T.H.
1 Soft 0 - 7 0 - 1,3 0 - 15
2 medium 8 - 14 1,4 - 2,5 16 - 25
3 hard 15 - 21 2,6 - 3,8 26 - 37
4 very hard > 21 > 3,8 > 37
Degrees of water hardness
German degreesGerman degrees
German degreesGerman degrees
German degrees
- 21 -
White with prewash
White without prewash
White, economy programme
Coloured
Delicate coloured
Rinsings
Spinning
Synthetics with prewash
Synthetics without prewash
Short programme
Delicate
Wool
Rinsings
Rinsing
Drain
A
B
B
C
D
F
G
H
J
K
L
M
N
P
R
Wash programmes
4,5 kg
2,0 kg
1,0 kg
2,0 kg
4,5 kg
Never turn the programme selector when the appliance is working.
90
40-90
E-60
40-60
30-40
60
40-60
30-60
-40
30-40
Prog.
Temp.
°C
Products
Max.
load
End of
prog.
Programmes
RESISTANT LAUNDRY
cotton -linen
DELICATE LAUNDRY
synthetics - wool
When the selected programme is over, the washing machine stops automatically. The timer knob stops on the position "I" by
a spinning phase for the cotton programmes. The synthetics programmes end by a rinse hold. You can end these programmes
with a draining (programme R) or with a spinning (by setting the timer on programme G). Please release the on/off pushbutton
" " before doing your choice.
If your linen is not spin dried at the end of the cycle, check the linen load is correctly spread out through the drum
before restarting a spin dry cycle.
BE CARREFUL :
THE LID CAN ONLY BE OPENED ABOUT 2 MINUTES AFTER THE MACHINE HAS STOPPED.
Spinning 600 rpm
Rinse hold
Drain
aI
bII
c
- 22 -
Wash code symbols
These symbols appear on fabric label, in order to help you choose the best way to treat your laundry.
Strong wash
WASH
Delicate wash
Max. wash
temperature 95°C
Max. wash
temperature 60°C
Max. wash
temperature 40°C
Max. wash
temperature 30°C
Hand
wash
Do not
wash
at all
BLEACHING Bleach in cold water
Do not bleach
IRONING
Hot iron max. 200°C Warm iron max. 150°C Lukewarm iron max. 110°C Do not iron
DRY CLEANING
Dry cleaning in
perchlorethylene petrol, pure
alcohol, R 111 & R 113
Dry cleaning
in all solvents
Dry cleaning in petrol, pure
alcohol, and R 113
Do not dry clean
DRYING On the lineFlat
On clothes hanger
Tumble dry
high
temperature
low
temperature
Do not tumble dry
Symbols identification on the panel of your washing machine :
/ / / / (cold wash) : adviced temperatures
: rinsing programme (soften)
a : prewash powder detergent compartment
b : wash powder detergent compartment
c : soften detergent compartment
: spinning for cotton programmes ( )
: rinse hold for synthetics programmes ( )
: draining
- 23 -
5. Select the temperature
Choose the temperature which corresponds to the chosen
programme, with the help or the indications of the pro-
gramme table, according to the fibers and the fastness of
the colours.
6. Select the programme
Choose the programme according to the nature and the
degree of soil of the laundry.
Turn the programme selector clockwise to select the chosen
programme.
Never turn the timer knob when the washing machine
is working.
7. Starting of programme
The ON/OFF pushbutton " " enables to switch on your
machine. The control lamp lights on and the programme
begins.
8. At the end of the programme.
When the selected programme is over, the machine stops
automatically. The timer knob stops on the position "I" for
the cotton programmes and on the rinse hold position for the
synthetics programmes. You can end these programmes by
a spinning (programme G) or by a draining (programme R).
Please release the " " on/off pushbutton before your
choice.
Be careful : a safety device enables to open the lid of your
waschine machine only about 2 minutes after the machine
has stopped.
After each wash:
depress the on/off pushbutton ; the control lamp lights
off.
press out the pushbutton (" ") if necessary
unplug the machine from the wall socket
turn off the water tap.
Operating instructions
1. Place the laundry in the drum
lift up the lid of the machine
open the drum with your two
hands by pressing the button A
and the two flapdoors till they
disengage
introduce the laundry into the
drum ; close the drum and the
lid of the machine
Be careful : before closing the lid of your machine, make
sure that the drum flapdoors are correctly closed :
- the two flapdoors fastened
- the button A pressed out.
2. Measure out the detergent
Measure out the amount of detergent recommended by the
manufacturer in the main wash compartment (bII).
If you wish to carry out a prewash, pour the amount required
into the prewash compartment (aI).
Do not exceed the MAX level.
If you wish to use liquid detergent :
choose a programme without prewash
put the measuring ball directly into the drum.
3. Add the fabric softener
Pour the softener, if required, into the compartment marked
c . Do not exceed the MAX level.
4. Press the half load " " pushbutton if required.
A
- 24 -
MAINTENANCE
Cleaning the machine :
Leave the lid open for a while after the wash to allow air
to circulate freely inside the machine;
The cabinet should be cleaned only with some soap-suds
and rinsed and dried carefully;
All polished, chromium plated and plastic parts should
only be cleaned with a damps cloth.
It is advisable, from time to time, to carry out a complete
cycle without a washing load, adding a decalcifying
product.
Clean the dispenser compartment from time to time to
remove remaining detergent.
Cleaning the pump filter
The machine has got another mecanic filter located on the
front part to collect lint and small objects (toothpins, coins,
pins, etc.) inadvertently left in the clothes. It is essential that
this filter is cleaned regularly.
Frequency of cleaning depends on the type of articles
washed (cleaning should be more frequent if the articles
have no hem and tend to fray).
To clean the filter proceed as follows :
Place the water discharge hose in a flat container placed on
the ground, to completely empty the machine.
Open the flap door of the filter
compartment by pressing it
inwards with a finger at the
hinged side (fig.1).
Turn the filter knob
counterclockwise and pull the
filter out (fig.2 and fig.3).
Clean the filter thoroughly.
Refit the filter and turn the knob clockwise.
fig. 3
fig. 1
fig. 2
BEFORE ANY MAINTENANCE OR CLEANING IS CARRIED OUT YOU MUST DISCONNECT THE APPLIANCE
FROM THE ELECTRICITY SUPPLY.
- 25 -
SOMETHING NOT WORKING ?
If the machine does not start up :
check that the lid is firmly shut;
check that the appliance is plugged in;
check that the mains fuse is intact;
check that the programme selector dial is correctly
positioned.
If the machine does not fill :
is the tap on ?
is water coming out of the tap? Check.
is the inlet hose squashed or bent?
is the filter of the inlet hose clogged?
If the machine empties as it fills:
the end of the drain hose is too low.
If the machine does not drain and/or does not spin:
is the drain hose squashed or bent?
is the drain filter clogged?
is it a rinse hold finishing a delicate programme?
If there is water on the floor:
too much detergent or unsuitable detergent? The
formation of foam can cause water leaks.
is one of the joints or the tap leaking? It is not always
easy to see as the leak often runs along the hose.
the detergent dispenser is clogged
the drainage system pipes are blocked.
If the machine vibrates or is too noisy:
have all the transit bolts and packing been removed?
is the machine touching something?
are all the feet resting firmly on the ground? Have the
lock nuts been secured?
If you are unable to identify or solve the problem,
consult our servicing department. Before telephoning,
make a note of the make, model and date of purchase
of your machine: the Service Department will require
these informations.
You will find these informa-
tions on the data plate of the
appliance. It is placed on the
filter door.
129 5805 01
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
AEG Electrolux EW622K User manual
- Category
- Washing machines
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI