Dacor Range DR30EIS User manual

Type
User manual

This manual is also suitable for

Dacor Range DR30EIS is a powerful and versatile cooking appliance that offers a wide range of features to make cooking easier and more enjoyable. With its spacious 30" width, the DR30EIS provides ample cooking space for even the largest meals. The range features four radiant elements, including two 6" elements and two 9" elements, which provide precise temperature control and rapid heating. The elements are also self-cleaning, making cleanup a breeze. In addition to its radiant elements, the DR30EIS also features a convection oven that provides even cooking and browning.

Dacor Range DR30EIS is a powerful and versatile cooking appliance that offers a wide range of features to make cooking easier and more enjoyable. With its spacious 30" width, the DR30EIS provides ample cooking space for even the largest meals. The range features four radiant elements, including two 6" elements and two 9" elements, which provide precise temperature control and rapid heating. The elements are also self-cleaning, making cleanup a breeze. In addition to its radiant elements, the DR30EIS also features a convection oven that provides even cooking and browning.

All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Distinctive
30” Wide
Electric Ranges
Document # PG05-008
Revised 11/09/12 Page 1/4
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.
OVERALL DEPTH DIMENSIONS - SIDE VIEW
Product Dimensions
Available Backguards
Part Number Description Compatibility
ADRB30E03 3 Inch Optional on all models
ADRB30E06 6 Inch
Standard on models DR30ES, DR30EFS
Optional on models DR30EIS, DR30EIFS
ADRB30E09 9 Inch Optional on all models
Models DR30EIS and DR30EIFS come equipped from the factory with
flat stainless trim piece in place of a backguard. A backguard may be
purchased as an optional accessory.
The trim on models DR30ES and DR30EFS are not compatible
with a raised vent.
Models DR30EIS and DR30EIFS are compatible with Dacor
raised vent models ERV3015. Use only theses specified raised
vent models.
Dimension DR30ES, DR30EIS DR30EFS, DR30EIFS
A 46 1/8” (117.2 cm) 46” (116.8 cm)
B 27 3/4” (70.5 cm) 27 5/8” (70.2 cm)
C 25 3/8” (64.5 cm) 25 1/4” (64.1 cm)
D 23 1/4” (64.1 cm) 23 1/8” (58.7 cm)
Model Versions
Model Configuration Handle Type
DR30ES
Freestanding,
(full size side panels)
Mounted on
outside of door
DR30ES-C*
Freestanding,
(full size side panels)
Mounted on
outside of door
DR30EFS
Freestanding,
(full size side panels)
Flush handle,
integrated in door
DR30EFS-C*
Freestanding,
(full size side panels)
Flush handle,
integrated in door
DR30EIS
Built-in/Slide-in
(3 1/4” removable side panels)
Mounted on
outside of door
DR30EIFS
Built-in/Slide-in
(3 1/4” removable side panels)
Mounted on
outside of door
* -C indicates Canadian wiring configuration, see page 3/4 for details.
1” (2.5 cm)
Front of open door
Front of handle/knobs
Front panel
Rear of front panel
Backguard thickness
3” (7.6 cm)
backguard*
External handle
shown, some models
have integral handle
(see inside cover)
6” (15.2 cm)
backguard*
*
See table for compatibility
Product width:
29 15/16” (76.0 cm)
35”
(88.9 cm)
to
37”
(94.0 cm)
9” (22.9 cm)
Backguard*
A
B
C
D
DR30EI[F]S:
3/8” (9.5 mm)
DR30E[F]S:
Full stainless
steel side panels
DR30EI[F]S:
3” (7.6 cm)
partial stainless
steel side panels
(removable)
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
Note 2
B
A
Non-combustible
surface along
back wall
recommended
Top of
finished
counter
13” (33.0 cm)
max.
4
18” (45.7 cm)
min.
4
C
Suggested
location of
utilities
3
Note 5
Note 1
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Distinctive
30” Wide
Electric Ranges
Document # PG05-008
Revised 11/09/12 Page 2/4
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
A* B
C
30 1/16” min.
(76.4 cm)
36” (91.4 cm) recommended
30” (76.2 cm) min.
37” (94.0 cm)
max.
FREESTANDING INSTALLATION CABINET CUTOUT DIMENSIONS - MODELS DR30ES, DR30EFS, DR30EIS AND DR30EIFS
* See the cutout dimensions on following page for self-rimming installations.
Failure to meet or exceed the maximum and
minimum dimensions/clearances stated may result
in a fire hazard.
The shaded area shown denotes the location of
the electrical junction box/receptacle. This is the
suggested location. For replacement purposes, the
location of the existing electrical supply may be
utilized provided that it does not interfere with the
sides or rear of the range.
Access to the remote circuit breaker panel/fuse box,
with the range in place and operating, must also be
allowed for in the installation.
The electrical junction box/receptacle must be
located so that it does not interfere with the range
when it is installed and under operation. In addition,
the junction box/receptacle must be located so
the range can be removed for service and remain
connected to power.
To eliminate the risk of burns or fire by reaching
over heated surface units, cabinet storage space
located above surface units should be avoided. If
cabinet storage space is to be provided directly
above the range, the risk of personal injury may be
reduced by installing a range hood.
In all instances, installation of a range hood is highly
recommended. The hood should project horizontally
a minimum of five (5) inches beyond the face of
the cabinets. See the range hood specifications for
minimum clearances.
The range may be installed flush to the rear wall.
See diagram and notes for rear wall surface
requirements. It is not necessary to install non-
combustible materials behind the range below the
countertop height.
Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.
1
30” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood
or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04
cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30” (76.2 cm) min. clearance between top of range grates and bottom of
unprotected wood or metal cabinet. If installing range hood, check the hood specifications for minimum required clearances.
2
Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.
3
Consult local code and following pages for requirements.
4
This specification not applicable for cabinets more than a horizontal distance of 10” (25.4 cm) from edge of range.
5
10” (25.4 cm) min. to combustible sidewalls above range (both sides).
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Distinctive
30” Wide
Electric Ranges
Document # PG05-008
Revised 11/09/12 Page 3/4
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
* To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm), with the width at the
notches remaining 30 1/16”. This configuration is only for models DR30EIS and DR30EIFS with side panels behind door removed.
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION, 3”
SIDE PANELS REMOVED
TOP VIEW - SLIDE-IN, SELF-RIMMING INSTALLATION, 3”
SIDE PANELS INSTALLED
Self-Rimming Installation Cutout Options (Models DR30EIS and DR30EIFS Only)
Electrical Specifications
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
30 1/16” (76.2 cm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (9.5 mm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
19 7/8”
(50.5 cm)
to
22 7/8”
(58.1 cm)
19 7/8”
(50.5 cm)
24 1/2”
(62.2 cm)
max.
Countertop front
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
30 1/16” (76.2 cm)*
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (9.5 mm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
22 7/8”
(58.1 cm)
24 1/2”
(62.2 cm)
max.
Countertop front
10 (25.4 cm)
10 (25.4 cm)
12 (30.5 cm)
2 1/2”
(6.4 cm)
3 1/2”
(8.9 cm)
1” (2.5 cm)
UTILITY CLEARANCE BEHIND RANGE
NEMA 14-50P PLUG NEMA 14-50R RECEPTACLE
ELECTRICAL REQUIREMENTS
Electrical Circuit
Required
Total Connected
Load**
240 Vac 60 Hz, 4 wire*,
50 Amp.
11.94kW (49.75 Amp.)
*Two 120 Vac hot (L1 and L2), one neutral (N1) and one ground.
**This information above is for reference only. If the above data
does not agree with the product data label, use the data on the
product data label.
IMPORTANT: Models DR30ES-C and DR30EFS-C are
freestanding ranges that come with a factory installed 4-wire
appliance cord and NEMA 14-50P plug. This wiring configuration
is required for freestanding ranges installed in Canada, although
they may be used elsewhere, if local codes permit. The plug
is designed to plug directly into a NEMA 14-50R electrical
receptacle installed by a licensed electrician according to the
above specifications.
Factory Wiring
Model Factory Electrical Connection
DR30ES Power cord not installed. Not for installation in Canada.
DR30ES-C
Cord connected, for installation in Canada and U.S.A.,
where local codes permit.
DR30EFS No power cord. Not for installation in Canada.
DR30EFS-C
Cord connected, for installation in Canada and U.S.A.,
where local codes permit.
DR30EIS No power cord. May be installed in Canada and U.S.A.
DR30EIFS No power cord. May be installed in Canada and U.S.A.
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
DR30ES, DR30EFS, DR30EIS, DR30EIFS
Distinctive
30” Wide
Electric Ranges
Document # PG05-008
Revised 11/09/12 Page 4/4
All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.
Only models DR30EIS and DR30EIFS may be installed with a raised
vent. Use only Dacor raised vent model ERV3015.
A self-rimming countertop configuration is required for raised vent
installation. On installations with a raised vent, when sliding the range
into position, it will stop when the rear of the control panel or side
panels contact the notches toward the front of the countertop.
The self-rimming installation of the DR30DI range and ERV3015
raised vent create a “built-in” look where the range trim overlaps the
countertop on both sides and the raised vent overlaps the countertop
in back.
* To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm), with the width at the notches remaining 30
1/16”. This configuration is only for models DR30EIS and DR30EIFS with side panels behind door removed.
TOP VIEW - DOWNDRAFT ERV30[15] WITH SLIDE-IN, SELF-RIMMING INSTALLATION USING
3” SIDE PANELS REMOVED
TOP VIEW - DOWNDRAFT ERV30[15] WITH SLIDE-IN, SELF-RIMMING INSTALLATION USING
3” SIDE PANELS INSTALLED
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
raised vent opening
27 1/2” (69.9 cm)
30 1/16” (76.2 cm)
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (1.0 cm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
19 3/4”
(50.2 cm)
to
22 3/4”
(57.8 cm)
19 3/4”
(50.2 cm)
2 5/8” (6.7 cm)
24 3/8”
(61.9 cm)
max.
Countertop front
Rear wall or
countertop edge
countertop opening
29 1/4” (74.3 cm)
raised vent opening
27 1/2” (69.9 cm)
30 1/16” (76.2 cm)*
cabinet opening
below countertop
below countertop
Cabinet face
Notch countertop
to width of cabinets
3/8” min. (1.0 cm)
countertop overhang
10” min. (25.4 cm)
to any combustibles
above counter both sides
22 3/4”
(57.8 cm)
2 5/8” (6.7 cm)
24 3/8”
(61.9 cm)
max.
Countertop front
Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.
Cabinet face
Countertop
Range trim resting
on countertop
DR30EI[F]S range
3/8” min. (1.0 cm)
flat countertop
overhang
25 9/16” (64.9 cm)
ERV3015
raised vent
3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener
Cabinet face
Countertop
Range trim resting
on countertop
Back of
side panel
rests against
cabinet face
DR30EI[F]S range
3/8” min. (1.0 cm)
flat countertop
overhang
25 9/16” (64.9 cm)
3 inch
side panel
ERV3015
raised vent
3/8” min. (1.0 cm) space
required behind ERV3015
chassis to clear stiffener
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dacor Range DR30EIS User manual

Type
User manual
This manual is also suitable for

Dacor Range DR30EIS is a powerful and versatile cooking appliance that offers a wide range of features to make cooking easier and more enjoyable. With its spacious 30" width, the DR30EIS provides ample cooking space for even the largest meals. The range features four radiant elements, including two 6" elements and two 9" elements, which provide precise temperature control and rapid heating. The elements are also self-cleaning, making cleanup a breeze. In addition to its radiant elements, the DR30EIS also features a convection oven that provides even cooking and browning.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI