Snapper R196019B User manual

Brand: Snapper

Model: R196019B

Category: Lawnmowers

Type: User manual

Snapper R196019B is a powerful cutting machine capable of mowing lawns with a 19-inch cutting width. Its sturdy steel deck ensures durability and longevity, while the Briggs & Stratton engine provides ample power for efficient cutting. The R196019B is designed for safety, featuring a blade control system that allows for quick and easy blade engagement and disengagement. It also comes equipped with safety shields and deflectors to protect the operator from flying debris. Additionally, the adjustable cutting height allows you to customize the mowing height to suit your lawn's needs.

Safety Instructions & Operator’s Manual for

19” STEEL DECK

WALK MOWERS

SERIES 19

MODEL

R196019B

MODEL NUMBER EXPLANATION

R 19 60 19 B

MODEL DESIGNATION ENGINE TYPE

CUTTING WIDTH SERIES DESIGNATION

ENGINE POWER *

R – Recycling Model 60 – 6.0 (Engine Power *) B – Briggs & Stratton Engine

19 – 19” Cutting Width 19 – Series Designation

Thank you for buying a SNAPPER Product! Before operating your Walk Behind, read this manual carefully and pay

particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 - 4. Remember that all power

equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance

with the operating instructions and common sense.

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* Actual sustained engine power will likely be lower due to operating limitations and environmental factors. Please refer to ‘Engine Power Rating

Information’ on Page 4 for further information.

BRIGGS & STRATTON YARD POWER PRODUCTS GROUP

MANUAL No. 7101116 (I.R. 3/12/2007)

TP 100-5264-IR-WB-N

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that

can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious

injury or death to the operator or other persons. The owner of the machine must understand these instructions

and must allow only persons who understand these instructions to operate machine. Each person operating

the machine must be of sound mind and body and must not be under the influence of any substance, which

might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your

dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER,

McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the machine and the mowing activity. Never assume that

children will remain where you last saw them.

1. KEEP children out of the mowing area and

under the watchful care of a responsible adult

other than the operator.

2. DO NOT allow children in yard when machine is

operated and turn machine OFF if anyone

enters the area.

3. DO NOT allow pre-teenage children to operate

machine.

4. ALLOW only responsible adults & teenagers

with mature judgment under close adult

supervision to operate machine.

5. DO NOT pull mower backwards unless

absolutely necessary. LOOK and SEE behind

and down for children, pets and hazards before

and while backing.

6. USE EXTRA CARE when approaching blind

corners, shrubs, trees, or other objects that

may obscure vision.

SLOPE OPERATION

1. Slopes are a major factor related to slip and fall

accidents, which can result in severe injury. All

slopes require extra caution. If you feel uneasy

on a slope, DO NOT mow it.

2. Mow across slopes, never up-and-down.

Exercise extreme CAUTION when changing

directions on slopes. DO NOT mow steep

slopes or other areas where stability or traction

is in doubt.

3. Use extra care with grass catchers or other

attachments; these affect the handling and the

stability of the machine.

PREPARATION

1. Read, understand, and follow instructions and

warnings in this manual and on the mower,

engine and attachments. Know the controls and

the proper use of the mower before starting.

2. Only mature, responsible persons shall operate

the machine and only after proper instruction.

PREPARATION

(Continued From Previous Column)

3. Data indicates that operators age 60 and above,

are involved in a large percentage of mower-

related injuries. These operators should

evaluate their ability to operate the mower

safely enough to protect themselves and others

from serious injury.

4. Handle fuel with extra care. Fuels are flammable

and vapors are explosive. Use only an approved

fuel container. DO NOT remove fuel cap or add

fuel with engine running. Add fuel outdoors

only with engine stopped and cool. Clean

spilled fuel and oil from machine. DO NOT

smoke.

5. Check the area to be mowed and remove all

objects such as toys, wire, rocks, limbs and

other objects that could cause injury if thrown

by blade or interfere with mowing. Also note the

location of holes, stumps, and other possible

hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop

mower if anyone enters the area.

7. Check shields, deflectors, switches, blade

controls and other safety devices frequently for

proper operation and location.

8. Make sure all safety decals are clearly legible.

Replace if damaged.

9. Protect yourself when mowing and wear safety

glasses, long pants and substantial footwear.

DO NOT mow barefooted or with sandals.

10. Know how to STOP blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the

machine into a trailer or truck.

12. Check grass catcher components frequently for

signs of wear or deterioration and replace as

needed to prevent injury from thrown objects

going through weak or torn spots.

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive

1. Extinguish all cigarettes, cigars, pipes and

other sources of ignition.

2. Use only an approved fuel container.

IMPORTANT SAFETY INSTRUCTIONS

SAFE HANDLING OF GASOLINE

(Continued From Previous Page)

1. DO NOT remove fuel cap or add fuel with the

engine running. Allow the engine to cool before

refueling.

2. DO NOT refuel the machine indoors.

3. DO NOT store the machine or fuel container

inside where there is an open flame, spark or

pilot light such as on a water heater or other

appliances.

4. DO NOT fill fuel containers inside a vehicle or

on a truck or trailer bed with a plastic liner.

Always place the containers on the ground

away from the vehicle before filling.

5. Remove gas-powered equipment from the

vehicle or trailer and refuel it on the ground. If

this is not possible, then refuel equipment

using a portable container, rather than a

gasoline dispenser nozzle.

6. DO NOT start gas powered equipment in

enclosed vehicles or trailers.

7. Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times until

fueling is complete. DO NOT use a nozzle lock-

open device

8. If fuel is spilled on clothing, change clothing

immediately.

9. DO NOT overfill a fuel tank. Replace fuel cap

and tighten securely.

OPERATION

1. DO NOT put hands or feet near or under

rotating parts. Keep clear of discharge area

while engine is running.

2. STOP engine when crossing gravel drives,

walks, or roads, and under any conditions

where thrown objects might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the

influence of alcohol or drugs.

5. After striking a foreign object or if mower

vibrates abnormally, STOP the engine,

disconnect and secure spark plug wire. Inspect

the mower for any damage and repair the

damage before starting.

6. DO NOT mow near drop offs, ditches or

embankments. Operator could lose footing or

balance.

7. STAY ALERT for holes and other hidden

hazards. Tall grass can hide obstacles. Keep

away from ditches, washouts, culverts, fences

and protruding objects.

8. DO NOT mow on wet grass. Always be sure of

your footing. Keep a firm hold on the handle

and walk, never run. Slipping could cause

injury.

9. ALWAYS stay behind handle when engine

(motor) is running.

OPERATION

(Continued From Previous Column)

10. DO NOT leave the machine with the engine

running. STOP BLADE and STOP ENGINE

before leaving the operators position for any

reason.

11. Before cleaning, repairing or inspecting make

certain engine, blade and all moving parts have

STOPPED. Disconnect and secure spark plug

wire away from plug to prevent accidental

starting.

12. STOP engine and wait until the blade comes to

complete STOP before removing grass bag

and/or clearing grass.

13. DO NOT operate mower without the entire grass

catcher, discharge guard, rear guard or other

safety devices in place and working.

14. DO NOT point discharge at people, passing

cars, windows or doors.

15. DO NOT discharge material against a wall or

obstruction. Material may ricochet back

towards the operator.

16. Slow down before turning.

17. Watch out for traffic when near or crossing

roadways.

18. DO NOT operate engine in enclosed areas.

Engine exhaust gases contain carbon

monoxide, a deadly poison.

19. Only use accessories approved by the

manufacturer. See manufacturer’s instructions

for proper operation and installation of

accessories.

MAINTENANCE AND STORAGE

1. DO NOT store mower or fuel container inside

where fumes may reach an open flame, spark or

pilot light such as in a water heater, furnace,

clothes dryer or other gas appliance. Allow

engine to cool before storing machine in an

enclosure. Store fuel container out of reach of

children in a well ventilated, unoccupied

building.

2. Keep mower and engine free of grass, leaves or

excess grease to reduce fire hazard and engine

overheating.

3. When draining fuel tank, drain fuel into an

approved container outdoors and away from

open flame.

4. Keep all bolts, especially blade bolts, nuts and

screws properly tight. Check that all cotter pins

are in proper position.

5. Always provide adequate ventilation when

running engine. Engine exhaust gases contain

carbon monoxide, a deadly poison.

6. Service engine and make adjustments only

when engine is stopped. Removed spark plug

wire from spark plug and secure wire away

from spark plug to prevent accidental starting.

IMPORTANT SAFETY INSTRUCTIONS

MAINTENANCE AND STORAGE

(Continued From Previous Page)

7. DO NOT change engine governor speed

settings or overspeed engine.

8. Check grass bag assembly frequently for wear

or deterioration to avoid thrown objects and

exposure to moving parts. Replace with new

bag if loose seams or tears are evident. Replace

slider or bag adapter if broken or cracked.

9. Mower blades are sharp and can cut. Wrap the

blades or wear heavy leather gloves and use

CAUTION when handling them.

MAINTENANCE AND STORAGE

(Continued From Previous Column)

10. DO NOT test for spark by grounding spark plug

next to spark plug hole; spark plug could ignite

gas exiting engine.

11. Have machine serviced by an authorized

SNAPPER dealer at least once a year and have

the dealer install any new safety devices.

12. Maintain or replace safety and instruction labels

as necessary.

13. Use only genuine SNAPPER replacement parts

to assure that original standards are

maintained.

Usage Statement

This manual contains safety information to make you aware of the hazards and risks associated with the

machine and how to avoid them. This machine is designed and intended to be used and maintained according

to the manual for finish cutting of established lawns and is not intended for any other purpose. It is important

that you read and understand these instructions thoroughly before attempting to start or operate this equipment.

Engine Power Rating Information

The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of

Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance

has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived

at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is

affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the

wide array of products on which engines are placed and the variety of environmental issues applicable to

operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of

power equipment (actual "on-site" or net horsepower). This difference is due to a variety of factors including, but

not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application

limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due

to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for

this Series engine.

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS................................................2-4

TABLE OF CONTENTS.............................................................................5

SECTION 1 - FAMILIARIZATION..............................................................6

SECTION 2 - OPERATING INSTRUCTIONS.......................................7-10

Pre-start Checklist......................................................................................................7

Starting & Stopping Engine & Blades................................................................... 7-8

Handle Height Adjustment.........................................................................................8

Cutting Height Adjustment ........................................................................................9

Recycling Operation...................................................................................................9

Recycling Cover Installation/Removal......................................................................9

Discharge Deflector Installation..............................................................................10

SECTION 3 - MAINTENANCE INSTRUCTIONS................................11-12

Change Engine Oil....................................................................................................11

Check Mower Blade..................................................................................................11

Service - Annually.....................................................................................................12

Engine ...................................................................................................................12

Air Filter ................................................................................................................12

Engine Oil .............................................................................................................12

Storage Procedure....................................................................................................12

SECTION 4 - ADJUSTMENTS AND REPAIR.........................................13

Mower Blade Replacement......................................................................................13

Mower Blade Sharpening.........................................................................................13

TROUBLESHOOTING.............................................................................14

SERVICE SCHEDULE.............................................................................15

Maintenance/Replacement Parts.............................................................................15

WARRANTY ............................................................................................16

PRIMARY MANTENANCE .................................................................17-20

PRODUCT REGISTRATION FORM........................................................21

IMPORTANT

The figures and illustrations in this manual are provided for reference only and

may differ from your specific model. Contact your Snapper dealer if you have

questions. NOTE: Specifications are correct at time of printing and are subject to

change without notice. Actual sustained equipment horsepower will likely be

lower due to operating limitations and environmental factors.

Section 1 - FAMILIARIZATION

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepared for the operators of

the SNAPPER WALK BEHIND MOWERS. Its

purpose, aside from recommending operating and

routine service requirements, is to promote safety

through the use of accepted operating practices.

Read, Understand and Follow the “IMPORTANT

SAFETY INSTRUCTIONS” on Pages 2 - 4 of this

manual and all safety messages on the mower and

attachments before operating the mower.

1.2 NOMENCLATURE

The nomenclature information above, Figure 1.1,

shows the essential parts of the SNAPPER WALK

BEHIND MOWERS. It is recommended that all

operators of the mower become thoroughly familiar

with the controls, parts and operation of the mower

before operating. Specific details involving the

engine are found in the separate engine owner’s

manual. Study these manuals before operating and

keep both handy for future reference.

BLADE CONTROL

FUEL FILLER

CAP

PRIMER

(SEE INSET)

RECYCLING

COVER

CUTTING HEIGHT

ADJUSTMENT

BUSHINGS

CUTTING DECK

MUFFLER

OIL FILL CAP &

DIPSTICK

ROPE

START HANDLE

AIR CLEANER

RECOIL

ROPE

GUIDE

KNOB

PRIMER BULB

Section 2 - OPERATING INSTRUCTIONS

2.1 PRE-START CHECK LIST

Make the following checks and perform the service

required before each start-up.

2.1.1. Check guards, deflectors, grass bag, adapter

and covers to make sure all are in place and securely

tightened.

2.1.2. Check blade control to insure it works freely.

See Figure 2.1.

FIGURE 2.1

2.1.3. Check cutting height. Adjust to desired height.

2.1.4. Check engine oil and add oil as needed to

bring level up to the full mark. Refer to Engine Owner’s

Manual for oil specifications. See Figure 2.2.

FIGURE 2.2

2.1.5. Add fuel to tank after pushing the mower

outside where fumes can safely dissipate. Fill tank to

1-1/2” below top of filler neck (to allow for fuel

expansion). Make sure cap is tightened after fueling.

Refer to Engine Owners Manual for fuel

specifications.

2.1.6. Clean exterior surfaces of cutting deck and

engine of any accumulation of spilled fuel, dirt,

grass, oil, etc. Keep engine air intake screen and

cooling fins clear at all times.

2.2 STARTING & OPERATION

2.2.1. ENGINE & BLADE

The engine speed is pre-set for optimum mowing

performance and is not adjustable. An engine primer

is provided to assist when starting a cold engine. The

primer should not be required when restarting a hot

engine.

1. Push primer bulb three times to start a cold

engine. NOTE: Primer should not be required when

restarting a hot engine. See Figure 2.3.

IMPORTANT: Stop the engine (and blade) by releasing

the blade control.

FIGURE 2.3

2. Pull blade control against handle.

3. Pull rope start handle to crank engine.

4. After engine starts, allow a brief warm-up until

engine runs smooth.

BLADE CONTROL

CHECK ENGINE OIL

PUSH PRIMER BULB

THREE TIMES

Section 2 - OPERATING INSTRUCTIONS

2.3 STOPPING

Stop engine and blade by releasing the blade

control. See Figure 2.4.

FIGURE 2.4

WARNING

DO NOT attempt any maintenance, adjustments or

service with engine and blade running. STOP engine

and blade. Disconnect spark plug wire and secure

away from spark plug. Engine and components are

HOT. Avoid serious burns, allow sufficient time for

all components to cool.

2.4 HANDLE HEIGHT ADJUSTMENT

The height of the mower handle can be adjusted as

follows:

1. Loosen the two nuts on the inside of each of the

lower handles as shown in Figure 2.5.

2. Move the handle up or down to the desired

height.

3. Retighten all nuts securely after adjustment.

FIGURE 2.5

LOOSEN NUTS TO

ADJUST HANDLE

HEIGHT

RELEASE BLADE

CONTROL TO STOP

ENGINE & BLADE

BLADE

CONTROL

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or

service with engine and blade running. STOP engine

and blade. Disconnect spark plug wire and secure

away from spark plug. Engine and components are

HOT. Avoid serious burns, allow sufficient time for

all components to cool. Wear heavy leather gloves

when handling or working around cutting blades.

Blades are extremely sharp and can cause severe

injury.

2.5 CUTTING HEIGHT ADJUSTMENT

1. FRONT WHEELS: Reposition the front axle by

raising the front wheels off the ground, then pull in

the spring loaded bushings until they clear the

brackets. Move bushings to the desired height of

cut position and release the bushings. See Figure

2.6.

2. REAR WHEELS: Reposition the rear axle by

raising the rear wheels off the ground, then pull in

the spring loaded bushings until they clear the

brackets. Move bushings to the desired height of

cut position and release the bushings. Position the

rear bushings in to the same notches

corresponding with notches for the front wheels to

maintain the level of the deck. See Figure 2.6.

NOTE: There are four cutting height adjustment notches

on each wheel. The top notch is the lowest cutting height

and the lowest notch is the highest.

FIGURE 2.6

2.6 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum

of 1/3 of grass blade length and recycle ONLY when

grass is dry.

1. Set all wheels in the highest cutting position

(Notch 4).

2. Proceed mowing slowly. If grass is very dense,

lower each rear wheel latch one notch lower than

the front wheel latches to improve recycling

performance.

2.7 RECYCLING COVER

(REMOVAL/INSTALLATION)

1. REMOVAL: The recycling cover is secured in

place with two knobs. To remove the cover,

unscrew the two knobs and lift off the cover. See

Figure 2.7.

2. INSTALLATION: When reinstalling the cover,

the deck sidewall should fit between the tab and

outside of cover. Tighten knobs securely. See

Figure 2.8.

FIGURE 2.7

FIGURE 2.8

KNOBS

SECURE COVER

RECYCLING

COVER

SPRING LOADED

BUSHING

DECK

BRACKET

TAB FITS BEHIND

DECK EDGE

TAB

MAKE CERTAIN

TAB FITS TO

INSIDE OF DECK

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or

service with engine and blade running. STOP

engine and blade. Disconnect spark plug wire and

secure away from spark plug. Engine and

components are HOT. Avoid serious burns, allow

sufficient time for all components to cool. Wear

heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp

and can cause severe injury.

WARNING

DO NOT operate mower without entire Grass

Catcher, Discharge Deflector or Recycling Cover in

place.

2.8 DISCHARGE DEFLECTOR

(INSTALLATION)

1. Remove the recycling cover. Loosen and

remove the two knobs securing the cover to the

deck and remove the cover from the two bolts. The

two bolts remain in the deck. See Figure 2.9.

2. Remove nut and bolt located below the front of

the discharge opening. See Figure 2.9.

FIGURE 2.9

3. Place discharge deflector over two bolts at top

of discharge opening and secure to deck using the

two knobs removed in Step 1. Tighten knobs

securely.

4. Using hardware removed in Step 2, insert bolt

with head on inside of deck into bottom rear hole of

discharge deflector. Secure to deck with nut. See

Figure 2.10.

FIGURE 2.10

TWO BOLTS

REMAIN IN

DECK

REMOVE THIS

NUT & BOLT

INSTALL DISCHARGE

DEFLECTOR OVER

DECK OPENING

INSTALL KNOBS

Section 3 - MAINTENANCE

3.1 INTRODUCTION

To retain the quality of the mower, use genuine

SNAPPER replacement parts only. Contact a local

SNAPPER dealer for parts and service assistance.

For the correct part or information for a particular

mower, always mention model and serial number.

3.2 SERVICE - AFTER FIRST 5 HOURS

3.2.1. CHANGE ENGINE OIL

WARNING

DO NOT attempt any maintenance, adjustments or

service with engine and blade running. STOP engine

and blade. Disconnect spark plug wire and secure

away from spark plug. Engine and components are

HOT. Avoid serious burns, allow sufficient time for

all components to cool. Wear heavy leather gloves

when handling or working around cutting blades.

Blades are extremely sharp and can cause severe

injury.

IMPORTANT: DO NOT tip machine with carburetor or

spark plug down. Oil from crankcase will saturate the air

filter and cause the engine to be hard to start or not start

at all. If contamination does occur, the air filter will have to

be replaced.

1. Disconnect spark plug wire and secure end

away from plug. The items needed to perform oil

change are: cloth rags, (1) 3/8” drive ratchet with a

short extension and (1) shallow pan.

2. Tilt mower up on its rear wheels for access to

the oil drain plug located underneath the mower

deck. Do not tilt mower with spark plug or

carburetor down. See Figure 3.1.

FIGURE 3.1

3. Place shallow pan underneath the approximate

center of the oil drain plug.

4. Loosen with ratchet and short extension, but do

not remove oil drain plug. Loosen plug until you

can turn it with your fingers.

5. Lower the mower down and place the piece of

wood under left rear wheel. Reach under mower

and remove drain plug and allow oil to drain out

completely in pan. Some oil may spill onto hands,

immediately wipe hands clean with cloth rags.

6. Tilt mower back up and replace drain plug.

Tighten securely but do not over tighten.

7. Fill engine with oil as specified in Engine

Owner’s Manual.

8. Check air cleaner and perform air filter

maintenance as specified in the Engine Owner’s

Manual.

IMPORTANT: DO NOT tip machine with carburetor or

spark plug down. Oil from crankcase will saturate the air

filter and cause the engine to be hard to start or not start

at all. If contamination does occur, the air filter will have to

be replaced.

3.2.2. CHECK MOWER BLADE

1. Disconnect spark plug wire and secure end

away from plug.

2. Tilt mower up on its rear wheels for access to

the blade cap screw. Do not tilt mower with spark

plug or carburetor down. See Figure 3.2.

3. Check torque of blade retaining cap screw.

Recommended torque should be 30 to 40 ft. lbs. of

torque. See Figure 3.2.

4. Check blade for sharpness, wear and damage.

Refer to Section “Blade Wear Limits”.

FIGURE 3.2

WARNING

To avoid spilling fuel, empty engine gas tank before

tilting mower.

BLADE

RETAINING

SCREW

CHECK TORQUE OF BLADE

RETAINING SCREW

TORQUE TO 30 to 40 FT. LBS.

DRAIN PLUG

Section 3 - MAINTENANCE

3.3 SERVICE - ANNUALLY

Perform all maintenance as described in the “Service

Schedule” section of this manual.

3.3.1. Engine

Service engine according to engine owner’s

manual.

3.3.2. Air Filter

Refer to engine owner’s manual for service

instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service

instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions

regarding engine storage preparations. Prepare the

mower for “end of season” storage as follows:

1. Drain fuel from fuel tank and let engine run until

all fuel is out of the carburetor.

2. Disconnect and remove the spark plug wire

away from spark plug before any other

preparations are made!

3. Tape all openings closed to prevent spraying

water into exhaust or air intakes during washing.

4. Tilt mower up on its rear wheels and thoroughly

clean the underside of the deck. Do not tilt mower

with spark plug or carburetor down. Scrape away

any accumulation of grass with a putty knife and or

wire brush.

5. Lubricate all exposed metal with a light coating

of oil to prevent corrosion.

6. Loosen handle knobs. Carefully fold the handles

forward, “flexing” the control cables to prevent

cable damage.

7. Store the mower in a shed or other dry area,

protected from weather.

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any maintenance, adjustments or

service with engine and blade running. STOP engine

and blade. Disconnect spark plug wire and secure

away from spark plug. Engine and components are

HOT. Avoid serious burns, allow sufficient time for

all components to cool. Wear heavy leather gloves

when handling or working around cutting blades.

Blades are extremely sharp and can cause severe

injury.

4.1 MOWER BLADE REPLACEMENT

4.1.1. STANDARD BLADE WEAR LIMIT

1. Inspect blade frequently for signs of excessive

wear or damage. See Figure 4.1.

FIGURE 4.1

WARNING

DO NOT use a cutting blade that shows signs of

excessive wear or damage. Refer to Section

“MOWER BLADE REPLACEMENT” for proper blade

inspection and service procedures.

4.1.2. BLADE SHARPENING

1. Disconnect spark plug wire and secure end away

from plug.

IMPORTANT: DO NOT tip machine with carburetor or

spark plug down. Oil from crankcase will saturate the air

filter and cause the engine to be hard to start or not start

at all. If contamination does occur, the air filter will have to

be replaced.

2. Tilt mower up on its rear wheels.

3. Remove blade. See Figure 4.2.

FIGURE 4.2

4. Sharpen blade on a grinding wheel at an angle of

22 to 28 degrees. DO NOT sharpen blade beyond

original cutting edge. See Figure 4.3.

FIGURE 4.3

5. Check blade for balance. If necessary, correct

balance by grinding heavy end of blade.

6. Reinstall blade. See Figure 3.2. Check torque of

blade retaining cap screw. Recommended torque

should be 30 to 40 ft. lbs.

WEAR LIMIT

(NOTCH STARTS)

DANGEROUS CONDITION !

DO NOT USE ON MOWER !

REPLACE WITH NEW BLADE.

NEW BLADE

BLADE

REMOVE BLADE

RETAINING SCREW

BLADE TIP

ORIGINAL

CUTTING EDGE

NOTE: DO NOT

SHARPEN BEYOND

ORIGINAL

CUTTING EDGE.

22-28º

END

VIEW OF

BLADE

TROUBLESHOOTING

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

Engine Will Not Start

1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.

Using Recoil Starter

2. Engine needs choking or priming. 2. Choke/Prime. Check Engine Manual for

instruction.

3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.

4. Spark plug faulty. 4. Replace with new spark plug.

Engine Stalls or Stops

After Running

1. Blade control is released or is not being held securely

against handle.

1. Blade control should be held securely against

handle at all times during operation of mower.

2. Fuel tank empty. 2. Fill with fuel to proper level.

3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.

4. Spark plug defective or gap set improperly. 4. Service spark plug.

5. Water, debris or stale fuel in fuel system. 5. Drain and clean fuel system.

Engine Loses Power

1. Engine air pre-cleaner or air cleaner dirty 1. Clean or replace filters.

2. Spark plug faulty. 2. Service spark plug.

3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.

Excessive Vibration

1. Damaged, out of balance or bent mower blade. 1. Service mower blade.

2. Loose blade components. 2. Service and tighten loose parts.

3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.

Cutting Grass

1. Cutting height too low or high. 1. Adjust cutting height.

Improperly

2. Engine speed too slow. 2. Contact authorized SNAPPER Dealer.

3. Forward ground speed too fast. 3. Walk at slower pace.

4. Terraced cut, side to side. 4. Adjust height of cut with height adjust bushings.

5. Excessive deck pitch, front to rear. 5. Adjust height of cut with height adjust bushings.

6. Cutting blade dull or damaged. 6. Sharpen cutting edges or replace blade.

Poor Grass Discharge

1. Engine speed too slow. 1. Contact authorized SNAPPER Dealer.

2. Grass is wet. 2. Mow when grass is dry.

3. Excessively worn or damaged blade. 3. Service mower blade.

4. Build up of grass clippings and debris under deck. 4. Clean deck.

5. Improper blade installed on deck. 5. Install proper SNAPPER blade.

6. Blade installed improperly on deck. 6. Install blade properly.

Oil Leaking

1. Leaking engine case. 1. Contact authorized SNAPPER dealer.

2. Check and tighten drain plug.

3. Make sure dipstick or oil filler cap is securely in

place.

SERVICE SCHEDULE

ITEM SERVICE PERFORMED REF. EACH

USE

HRS

100

HRS

EACH

SEASON

Engine Oil

Check Oil Level Page 7

Initial Oil Change Page 11

Periodic Oil Change Page 12

Air Cleaner

Clean or Replace Engine Manual.

X**

Spark Plug

Replace Engine Manual.

Mower Blade

Check For Wear, Damage

& Replacement

Page 11 & 13

Mower Deck

Clean Debris

Accumulation

Page 12

* Change oil every 25 hours when operating under heavy load or high temperatures.

**Clean more often under dusty conditions or when air debris is present

4.2 MAINTENANCE/REPLACEMENT PARTS

MAINTENANCE PARTS

Blade Control Cable 7072933

Cutter Blade (Mulching) 7017167

Parts Manual for 19” Steel Deck Walk Behind Mower Series 14, 15, 17 & 19 7006066

2 YEAR LIMITED WARRANTY

For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through

any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts

found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

For ninety (90) days from purchase date for the original purchaser's commercial, rental, or other non-residential use,

SNAPPER, through any authorized SNAPPER dealer will replace, free of charge, any part or parts found upon

examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.

All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for

replacement under this warranty must be paid by the purchaser.

This warranty does not apply to certain transmissions, to engines and their components, and batteries, as these items

are warranted separately. This warranty does not apply to parts that have been damaged by accident, alteration,

abuse, improper lubrication, normal wear, or other cause beyond the control of SNAPPER. This warranty does not

cover any machine or component part that has been altered or modified changing safety, performance, or durability.

Batteries have a one (1) year warranty period with free replacement if required for one (1) year from the original

purchase date. SNAPPER will not be responsible for any installation cost incurred. The battery warranty only covers

original equipment batteries and does not cover damage to the battery or machine caused by neglect or abuse,

destruction by fire, explosion, freezing, overcharging, improper maintenance, or use of improper electrolyte.

There is no other express warranty.

DISCLAIMER OF WARRANTY

Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to two (2)

years from purchase date for the original purchaser's residential or other non-commercial use, and ninety (90)

days from purchase for the original purchaser's commercial, rental or other non-residential use, and to the

extent permitted by law, any and all implied warranties are excluded. This is the exclusive remedy. Liabilities

for consequential damages, under any and all warranties are excluded.

Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

WARNING: THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE

SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER

ASSOCIATED WITH THE USE OF SUCH PARTS.

IMPORTANT: Please fill out the attached SNAPPER Product Registration Card immediately and mail to:

Snapper’s Product Registration Center, P.O. Box 1379, McDonough, Georgia 30253

PRIMARY MAINTENANCE

Page is loading ...

Snapper R196019B User manual

Brand: Snapper

Model: R196019B

Category: Lawnmowers

Type: User manual

Download PDF

report

Snapper R196019B User manual

Snapper R196019B User manual

Related papers

Other documents