Allen-Heath ML4000 User manual

Category
Audio mixers
Type
User manual

This manual is also suitable for

ALLEN&HEATH
GL4000
Dual Function Audio Mixing Console
USER GUIDE
PUBLICATION: AP2642
1
Publication ............. AP2642 Issue 3copyright © 2001 ALLEN & HEATH. All rights reserved
USER GUIDE
CONTENTS
Warranty ............................................................... 2
Introduction ........................................................... 3
Overview .............................................................. 4
Range and Options ............................................... 5
Dimensions and Weights ...................................... 6
Specifications ....................................................... 7
System Block Diagram ......................................... 8
Connectors ......................................................... 10
Earthing .............................................................. 13
Connecting the Power Unit ................................. 14
Matching the Signal Levels ................................. 15
Mono Input Channel ........................................... 16
Stereo Input Channel .......................................... 18
Stereo Channel Applications............................... 19
Group Section .................................................... 20
LR Section .......................................................... 21
Mono and Master Section ................................... 23
The Mute System ............................................... 26
Mute Groups ....................................................... 28
Mute Safes ......................................................... 31
Mute Patches ..................................................... 32
The Patch Display .............................................. 33
QuickSolo ........................................................... 36
Solo Safes .......................................................... 37
MIDI .................................................................... 38
Technical Support............................................... 42
Front-of House Application ................................. 44
On-Stage Monitor Application ............................. 48
Multi-Speaker System Application ...................... 51
Internal Link Options ........................................... 52
Panel Layout Drawing ............................. rear cover
2
LIMITED ONE YEAR WARRANTY
This product has been manufactured in the UK by ALLEN &
HEATH and is warranted to be free from defects in materials
or workmanship for a period of one year from the date of
purchase by the original owner.
To ensure the high level of performance and reliability for
which this equipment has been designed and manufactured
please read this User Guide before use.
In the event of a failure notify and return the defective unit to
ALLEN & HEATH or its authorised agent as soon as possible
for repair under warranty subject to the following conditions:
CONDITIONS OF WARRANTY
1. The equipment has been installed and operated in accordance with the
instructions in the User Guide.
2. The equipment has not been subject to misuse either intended or
accidental, neglect, or alteration other than as described in the User
Guide or Service Manual, or approved by ALLEN & HEATH.
3. Any necessary adjustment, alteration, or repair has been made by
ALLEN & HEATH or its authorised agent.
4. The defective unit is to be returned carriage prepaid to ALLEN &
HEATH or its authorised agent with proof of purchase.
5. Units to be returned should be packed to avoid transit damage.
These terms of warranty apply to UK sales. In other territories the terms
may vary according to legal requirements.
MANUFACTURED IN THE UNITED KINGDOM
Allen & Heath Limited.
Kernick Industrial Estate,
Penryn, Cornwall, TR10 9LU.
http://www.allen-heath.com
This product complies with the European
Electromagnetic Compatibility Directives 89/336/EEC
& 92/31/EEC and the European Low Voltage Directives
73/23/EEC & 93/68/EEC.
3
INTRODUCTION
The GL4000 continues ALLEN & HEATH’s commitment to provide high quality audio mixing
consoles engineered to meet the exacting requirements of today’s audio business. It brings you the
latest in high performance technology and offers the reassurance of over two decades of console
manufacture and customer support.
This user guide presents a quick reference to the function and application of the GL4000. For further
information on the basic principles of audio system engineering please refer to one of the specialist
publications available from bookshops and audio equipment dealers.
Whilst we believe the information in this guide to be reliable we do not assume responsibility for
inaccuracies. We also reserve the right to make changes in the interest of further product
development.
SERVICE AND TECHNICAL SUPPORT
Under normal conditions the GL4000 does not require user maintenance or internal calibration. In
certain cases it may be necessary to reconfigure internal option links. This and any service work
required should be carried out by qualified service or engineering personnel only.
We are able to offer further product support through our worldwide network of approved dealers and
service agents. To help us provide the most efficient service please keep a record of the console
serial number, and date and place of purchase to be quoted in any communication regarding this
product.
GENERAL PRECAUTIONS
POWER SUPPLY Use only the power unit specified for the console. Check the unit for
correct AC mains voltage setting before switching on. Allow adequate space around the unit for
ventilation.
CONNECTIONS Use audio connectors and cables only for their intended purpose. Do not
connect any source of AC or DC power to the console audio connectors. Do not connect the output
of power amplifiers directly to the console.
CLEANING Avoid the use of chemicals, abrasives and solvents. The control panel is best
cleaned with a soft brush and dry lint-free cloth. To remove stubborn marks (such as chinagraph
pencil) isopropyl alcohol may be used.
LUBRICATION The faders, switches and potentiometers are lubricated for life. The use of
electrical lubricants on these parts is not recommended.
DIRT, DUST, SMOKE and MOISTURE Prevent damage to the moving parts, such as faders
and potentiometers, and cosmetics by avoiding drinks spillage, tobacco ash, smoke, and exposure
to rain and condensation. Protect from excessive dirt, dust, heat and vibration.
Mains electricity is dangerous and can kill. Mains voltage is present within the power
supply unit provided with the console. Do not remove the power unit cover with mains
connected. The correct mains voltage setting is indicated on the rear of the power unit. Check
your mains wiring and earthing before switching on.
DO NOT REMOVE THE MAINS EARTH CONNECTION!
The console chassis is connected to mains earth to ensure your safety. Audio 0V
connects to the console chassis internally. Should problems be encountered with ground
loops operate the audio ground lift switches on connected equipment accordingly or
disconnect the cable screens at one end. Refer to the section on 'EARTHING' later in this User
Guide.
SAFETY WARNING
4
Dual function + live recording capability :
Large venue Front-of-House
Dedicated 12 buss (10mix+LR) stage monitor
Dual function combines Front-of-House and monitor
Live recording to 2-track and multitrack
24, 32, 40, 48 frame sizes including VU Meterpod
Stereo models include mic/stereo line channels depending
on customer specification
8 groups with inserts and trimmable balanced XLR outputs
L,R,M mix on balanced XLR and with inserts
10 Aux sends on balanced XLR and with inserts
4 Matrix capable of balanced XLR and inserts
Matrix to aux link feature for group effects and monitors
Secondary LR output capable of balanced XLR and inserts
Channel Direct outputs with level trim and pre/post
4 band full sweep channel EQ with mid Q switches
Stereo channel 4-point width control
Separate insert jacks with balanced returns
MIDI mute system with 128 patches
8 independent mute groups
Solo-in-place with QuickSolo feature
Full metering - channel, mix buss and outputs.
Monitor with stereo PFL, local output, 2 phones ...
Simultaneous stereo and mono PFL metering
Output meter selector switches for main or aux
Talkback to L-R, M, groups, matrix, and to each aux
2-track replay to L-R and monitor
The console is constructed using extruded aluminium beams, steel panels and
3mm thick metal side plates to ensure rigidity and mechanical reliability on the road,
as well as easy flightcasing. Individual circuit assemblies are accessible by removal
of the steel base. A durable but soft front armrest is provided for comfort. Front,
top and rear write-on strips are provided for channel marking. High quality proven
reliable parts are used throughout. High performance op-amp and discrete circuits
are used to ensure low noise and sonic purity.
The GL4000 reflects our commitment to providing the best audio mixing solutions
and customer support.
OVERVIEW
The GL4000 offers the professional user an uncompromised feature set and
performance for live sound engineering and recording. The console is available in
24, 32, 40 and 48 channel sizes with an external 3U rack power unit. Options
include bolt-on expander module, SYS-LINK interconnect system and 1U dual
power supply monitor/combiner unit. Units from Serial Number 403421 include a
built-in VU Meterpod as standard. An optional VU Meterpod is available for earlier
units.
5
THE RANGE
The following GL4000 models and options are
available. For further details please contact
your Allen & Heath agent :
GL4000-824 - 24 channel console
GL4000-832 - 32 channel console
GL4000-840 - 40 channel console
GL4000-848 - 48 channel console
The Stereo models can include mic/stereo line
channels dependant on customer specification.
The console is supplied with separate power
supply, DC power cable and mains cable with
moulded plug.
GL4000-8M - 8 mono channels expander
GL4000-4SM - 4 stereo, 4 mono expander
GL4000-4MS - 4 mono, 4 stereo expander
These expander modules are fitted by removing
the console side plate, attaching to the chassis,
and plugging in the harnesses. The console
may be expanded to a maximum of 48 channels.
RPS11 - 300W rack power unit with DC cable
RPSD2 - Dual supply combiner/monitor
1U 19" rack unit which allows two power units to
connect to one console for redundant supply
backup. Also provides local and remote DC rail
LED monitoring.
The Integral Meterpod provides illuminated
moving coil VU metering of the groups, L,R,M
(or monitors, LR sidefill, listen wedge). Also
additional PFL/AFL indicator.
GL4000-SL1 - SYS-LINK expander option
Circuit assembly and multi-pin connector system
which can be fitted to the console to allow
simple interconnection between two consoles
so that one becomes the slave of the second by
linking the audio busses and PFL/AFL system.
SYS-LINK interconnects using two standard
25way D-type cables to any other console fitted
with the SYS-LINK system.
This option should be fitted only by your Allen &
Heath agent or competent service personnel.
6
DIMENSIONS AND WEIGHTS
Dimensions shown in millimeters.
UNPACKED
Width Depth Height Wt (kg)
GL4000M-824 1166 (46") 748 (29.5") 285 (11.2") 47 (104lbs)
GL4000M-832 1421 (56") 748 (29.5") 285 (11.2") 57 (126lbs)
GL4000M-840 1676 (66") 748 (29.5") 285 (11.2") 67 (148lbs)
GL4000M-848 1931 (76") 748 (29.5") 285 (11.2") 77 (170lbs)
GL4000-8M 255 (10") 748 (29.5") 285 (11.2") 9 (20lbs)
RPS11 483 (19") 232 (9.1") 135 (3U) 10 (22lbs)
RPSD2 483 (19") 180 (7.1") 45 (1U) 6 (13lbs)
PACKED
Width Depth Height Wt (kg)
GL4000M-824 1702 (67") 900 (35") 390 (15.4") 82 (181lbs)
GL4000M-832 1702 (67") 900 (35") 390 (15.4") 91 (201lbs)
GL4000M-840 1950 (76.8") 900 (35") 390 (15.4") 100 (221lbs)
GL4000M-848 1931 (76") 900 (35") 390 (15.4") 129 (284lbs)
GL4000-8M 480 (18.9") 830 (32.7") 260 (10.2") 12 (26lbs)
RPS11 575 (22.6") 270 (10.6") 170 (6.7") 11 (24lbs)
RPSD2 520 (20.5") 260 (10.2") 115 (4.5") 6 (13lbs)
7
SPECIFICATIONS
0dBu = 0.775 Vrms Reference for high level equipment +4dBu = 1.23 V
0dBV = 1 Vrms Reference for low level equipment -10dBV = 310 mV
0VU meter reading = +4dBu at XLR outputs
INPUT GAIN
Mic/Line Input ................. +6dB to +60dB variable
Mic/Line + Pad ............... -14dB to +40dB variable
Line Input ....................... -14dB to +40dB variable
Stereo Line Input ............ off to +10dB variable
2-track Return ................ off to +10dB variable
MAXIMUM OUTPUT LEVEL
Main Outputs .................. +27dBu into load of >600 ohm
Jack Outputs .................. +21dBu into load of >2K ohm
Internal headroom .......... +21dB
FREQUENCY RESPONSE
Measured 20Hz to 20kHz ref 1kHz
Mic to mix (+40dB) ......... +0/-0.5dB
Line to mix (0dB) ............ +0/-0.5dB
DISTORTION
THD + noise measured @ 1kHz +20dBu
Mic to mix (+40dB) ......... 0.006%
Line to mix (0dB) ............ 0.006%
CROSSTALK
Referred to driven channel @ 1kHz
Channel to channel ........ > 100dB
Mute shutoff ................... > 85dB
Fader shutoff .................. > 90dB
NOISE PERFORMANCE
Measured rms 22Hz to 22kHz bandwidth
Mic EIN........................... -128dB 150 ohm source
Line pre-amp (0dB) ........ < -91dBu
Residual output noise ......................... < -98dBu (-102dB S/N)
Mix noise, nothing routed ................... < -87dBu (-91dB S/N)
Mix noise, 24 channels routed ............ < -81dBu (-85dB S/N)
METERING
Input meters ................... 4 segment LED (signal, 0, +6, peak)
Mix meters ...................... 4 segment LED (signal, 0, +6, peak)
Output meters ................ 12 segment LED
LED meter response ...... peak reading
Peak indicators ............... on 5dB before clipping
Signal indicators ............. on -20dBu
Meterpod ........................ Illuminated VU moving coil meters
8
MODE SWITCHING
Protected underpanel mode switches set the console architecture according to the required application, for example FOH
or stage monitor. Select these using a pointed object.
DIR OUT routes the channel direct out signal
through the aux 10 pre/post selector and
level control.
OUT REV swaps the matrix or LR2 output
jack with the related aux XLR and insert. The
control sections are not swapped. This can
provide matrix outputs on XLR with inserts, or
aux effects sends on jack as required.
TRIM ON routes the group output signal
through a pre/post fader selector and level
trim. This lets you record the groups
independent of the subgrouping to LR and M.
MTX TO AUX Links the matrix mix into the
aux mix to include aux sends from the groups,
LR and M. Used for effects from the groups,
and for quick monitor mixes.
GRP REV reverses the aux (small fader) and
group (main fader) control sections. Also
applies to LR. The outputs remain unaffected.
This mode is used for stage monitoring.
MONO MODE converts the mono output to
the monitor engineers listen wedge. M AFL
is disabled. The M mix still feeds the insert
and matrix.
9
SYSTEM DIAGRAM
10
CONNECTORS
Professional gold plated connector types are used to ensure continued reliable
operation. All the console main inputs and outputs are balanced XLRs. All 1/4" jacks
are 3-pole TRS for operation with balanced or unbalanced equipment. Inserts are
provided on all channel inputs, and on Groups, L, R, Mono and all Aux outputs. Aux
can be swapped with matrix and LR2 for XLR outputs with inserts
DIRECT OUTPUT
Provides a buffered signal from the channel, ideal for minimum
signal path connection to multitrack recorders or local effects
sends. Set post-fader, post-mute as standard. Can be switched
through the Aux10 send control for pre/post fader selection and
level trim with +6dB maximum boost.
3-pole 1/4" jack socket (tip = hot). Impedance balanced 50 ohm
0dBu line level for connection to balanced or unbalanced equipment.
INSERT SEND
Used to send the channel signal to external effects and signal
processing equipment, post-pre-amp and pre-EQ.
3-pole 1/4" jack socket (tip = hot).
Impedance balanced 0dBu 50ohm line level.
INSERT RETURN
Used to return the processed signal from external equipment into
the channel audio signal path pre-EQ.
3-pole 1/4" jack socket (tip = hot). Balanced >10kohm 0dBu line
level. (Stereo channel returns are unbalanced).
MIC/LINE INPUT
3-pin female XLR (pin 2 = hot). Electronically balanced.
74dB gain range. Mic impedance >2kohm, line >10kohm
Can be used for XLR line input when the LINE IN jack is left
unplugged.
MONO CHANNEL LINE INPUT
3-pole 1/4" jack socket (tip = hot). Electronically balanced >10kohm.
STEREO CHANNEL LINE INPUT
3-pole 1/4" jack socket (tip = hot). Electronically balanced >10kohm.
Plug into the Left input only for a mono line source.
11
SYS-LINK EXPANDER OPTION
Available as a kit to be fitted to the console to expand the busses.
Uses 4 25-pin D-type connectors (input and output A and B).
Operates at -2dBu line level. Refer to your Allen & Heath agent for
further details.
GROUP/AUX/L/R/M INSERT SEND
Used to send the output signal to external effects and signal
processing equipment such as graphic equalisers, delays and
compressors, post-mix amp and pre-fader.
3-pole 1/4" jack socket (tip = hot).
Impedance balanced -2dBu 50ohm line level.
GROUP/AUX/L/R/M INSERT RETURN
Used to return the processed signal from external equipment into
the output audio signal path pre-fader and mix meter.
3-pole 1/4" jack socket (tip = hot). Balanced >10kohm -2dBu line
level.
GROUP/AUX/L/R/M MAIN OUTPUT
3-pin male XLR (pin 2 = hot). Electronically balanced 75ohm.
+4dBu line level, +27dBu maximum into 600 ohm load.
Capable of driving long cable runs without loss or interference.
MODE SWITCHING
Set the underpanel mode switches for the intended console
operation. Some of these affect the way the connectors work. For
full details please refer to the BLOCK DIAGRAM.
OUT REV underpanel mode switch - The Aux XLRs and
inserts can swap with the Matrix and LR2 output jacks for aux
(effects) sends on jacks if required. This also provides matrix and
LR2 outputs on XLRs with inserts for driving speaker systems.
MONO MODE underpanel mode switch - The Mono output
becomes the engineers listen wedge monitor feed when the
console is operated in on-stage monitor mode. However, the Mono
insert remains with the mono mix.
MIX/AUX REV underpanel mode switch - Note that while the
front panel control sections are swapped when the reverse mode
switches are pressed, the signals always appear at their related
connectors, ie. the connectors do not swap.
12
METERPOD CONNECTOR
Recessed 16-pin dual row header for connection to the meterpod.
LOCAL STEREO MONITOR
For connection to a stereo amplifier/speaker system for LR, AFL/
PFL monitoring local to the console.
3-pole 1/4" jack sockets (tip = hot). Impedance matched 50ohm
0dBu nominal line level.
HEADPHONES
Connections for 2 stereo headphones >8ohms. One connector is
on the front panel, the other is concealed under the armrest.
3-pole 1/4" jack sockets (tip = left, ring = right).
MATRIX OUTPUT
3-pole 1/4" jack socket (tip = hot). Impedance balanced 50ohm
0dBu nominal line level.
Can swap with the aux output XLRs and inserts to drive long cable
runs without loss or interference, and to insert external signal
processing devices such as graphic equalisers and delays.
LR2 OUTPUT
Secondary LR output for 2-track recording, broadcast or additional
speaker and zone feeds.
3-pole 1/4" jack socket (tip = hot). Impedance balanced 50ohm
0dBu nominal line level.
Can swap with the aux output XLRs and inserts to drive long cable
runs without loss or interference, and to insert external signal
processing devices such as graphic equalisers and delays.
2-TRACK RETURN INPUT
For connection to 2-track playback equipment such as cassette,
DAT or CD players.
3-pole 1/4" jack sockets (tip = signal). Unbalanced 50ohm. +10dB
maximum gain allows connection to low and high level equipment.
MIDI INTERFACE
Standard 5-pin 180' connectors for opto-isolated connection to
other MIDI equipment. A mute processor reset switch is provided.
CONSOLE DC POWER INPUT
The console connects to a separate power supply unit via a 10-pin
circular connector cable. Connect only the Allen & Heath power
unit supplied with the console.
A chassis ground terminal post is provided. This connects to mains
earth through the power cable.
13
EARTHING
The connection to earth (ground) in an audio system is important for two reasons:
1. SAFETY - To protect the operator from high voltage shock associated with the AC
mains supply feeding the system, and
2. AUDIO PERFORMANCE QUALITY - To minimise the effect of earth (ground) loops
which result in audible hum and buzz, and to shield the audio signals from external
interference.
For safety it is important that all equipment earths are connected to mains earth so that
exposed metal parts are prevented from carrying high voltage which can injure or even kill
the operator. A solid, low impedance earth system is necessary to ensure that earths at
different points in the system are kept at the same potential. A typical sound system
includes amplifiers, signal processing equipment, microphones, musical instruments and
much more in addition to the console, all of which require earth connection for safety and
correct audio operation. Often this equipment is spread across the venue and interconnected
by hundreds of metres of power and audio cables. It is recommended that the sound
engineer check the continuity of the safety earth from all points in the system including
microphone bodies, guitar strings, muticore cases, equipment panels ...
The same earth is also used to shield audio cables from external interference such as the
hum fields associated with power transformers, lighting dimmer buzz, and computer
radiation. Earth is also used for the signal 'return' when connecting to unbalanced
equipment. Problems arise when the signal sees more than one path to mains earth. An
'earth loop' (ground loop) results causing current to flow between the different earth paths.
A larger potential difference between these paths results in more current flow and so more
audible noise. This condition is usually detected as a low frequency hum or buzz at mains
frequency or its harmonics.
To ensure operator safety and trouble-free audio performance from your system we
recommend the following :
Do not remove the earth connection from the power unit mains plug. The
console chassis is connected to mains earth through the power cable to ensure your safety.
Audio 0V is connected to the console chassis internally. If problems are encountered with
earth loops operate the audio 'ground lift' switches on connected equipment accordingly,
or disconnect the cable screens at one end, usually at the destination. It is useful to carry
ground lift cable adaptors such as short XLR male to female leads with pin1 disconnected.
Use a separate 'clean' mains outlet for the audio equipment to prevent
interference from other equipment such as lighting, stage machinery and vending
machines. Ensure a good central 'star point' earth connection.
Avoid running audio cables next to mains, computer or lighting cables, or near
thyristor dimmer and power supply units. If unavoidable, cross these at right angles.
Use low impedance sources such as 200 ohm or less microphones to reduce
susceptability to interference. The console outputs are designed to operate at very low
impedance to minimise interference problems.
Use balanced connections where possible as these provide further immunity by
cancelling out interference that may be picked up on long cable runs. To connect an
unbalanced source to a balanced console input, link the cold input (XLR pin3 or jack ring)
to 0V earth (XLR pin1 or jack sleeve) at the console. To connect a balanced console output
to an unbalanced destination, link the cold output to 0V earth at the console.
Use professional quality cables and connectors and check for correct wiring and
reliable solder joints.
If you are not sure ... Have your system checked by a competent engineer, or
contact your local Allen & Heath agent for advice.
14
DO NOT OBSTRUCT VENTILATION OPEN INGS.
SEE INSTA LLATION INSTRUC TIONS BEF ORE CONNE CTING TO THE SUP PLY.
ALLOW ADEQUATE VENTILATION AROUND THE UNIT.
V-
CARACTERISTIQUES.
T 10A 250V 20mm
DC FU SES
REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
V+
OFFON
ALLOW ADEQUATE VENTILATION AROUND THE UNIT.
DO NOT OBSTRUCT VENTILATION OPENINGS.
WARNING - THIS APPARATUS MUST BE EARTHED.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE
SERIAL No:
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR.
CAUTION
WITH SAME TYPE AND RATING.
ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES.
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE
NO USER SERVICEABLE PARTS INSIDE
FUSE TYPE AC SUPPLY
T 5.0A 20mm 100 - 120V~
T 3.15A 20mm 220 - 240V~
47-63Hz
300W MAX
320VA MAX
AC MAINS IN ~
CONNECTING THE POWER UNIT
Connect only the Allen & Heath power unit specified for the console. The standard unit for GL4000
is the RPS11. This is an external 3U 19" rack mounted unit that connects to the console via the
separate DC cable supplied. The RPS11 is a low noise linear design that converts AC mains voltage
to the DC voltages required to power the console. It also provides +48V phantom power for use with
high quality powered microphones. The presence of AC mains voltage is shown on the power unit
front panel neon indicator. The presence of the DC voltages is shown on the console power indicator
LEDs. A second backup RPS11 may be connected to the console through the optional RPSD-2 dual
supply combiner unit available from your Allen & Heath agent if required.
SAFETY WARNINGS !
Ensure that the warnings printed on
the power unit (shown here) are
followed.
Always switch the power unit off before
connecting or disconnecting the
console power cable.
It is normal for the power unit to dissipate
heat. Do not cover the unit or position
it on soft furnishings during operation.
Do not position other equipment known
to generate significant amounts of heat
below the unit. It is recommended that
rack units containing high power
amplifiers and other heat dissipating
equipment are fitted with cooling fans.
BEFORE SWITCHING ON !
Check that the voltage indicated on the
fuseholder is correct for the mains
voltage in your area.
Check that the mains IEC connector is
fully inserted into the inlet socket.
Check that the DC power cable is
correctly fitted to both the power unit
and the console. The locking ring
should be screwed in place.
It is recommended that audio power
amplifiers are switched on last and
switched off first to prevent possible
damage to loudspeakers.
Check the system for safety earthing.
15
MATCHING THE SIGNAL LEVELS
For best performance it is important that the connected source signals are
matched to the "normal operating level" of the console. Similarly the
console outputs should be correctly matched to the operating levels of the
connected amplifiers and destination equipment. If too high the signal
peaks will be clipped resulting in a harsh distorted sound, and if too low
the signal-to-noise ratio is reduced resulting in excessive background hiss
and noise.
For best results operate the console with the meters averaging around '0'
letting the louder passages peak into the 'yellow'. Reduce the gain if the
red peak indicators flash. The GL4000 produces a standard XLR output
level of +4dBu for a meter reading of 0VU. It is advisable to adjust the
power amplifier input gain or fit an attenuator pad if normal console
operation results in an output level too high for the connected amplifier.
Normal operation should result in fader levels around the '0' mark. Note
that when reversed with the auxes the matrix and LR2 output level trims
can be used to match the console to the amplifiers independent of the mix
levels. Similarly the group output trims can be switched in to match levels.
The GL4000 has an advanced PFL (pre-fade listen) / AFL (after-fader
listen) and channel metering system to let you listen to and check the level
of signals at different points in the signal path without affecting the main
outputs. Use the channel PFL switches to set up the input GAIN controls
to read an average '0'. Signal activity is always shown on the channel
meters regardless of fader position. The green 'SIG' LED lights at -20dBu
to indicate signal presence, the green '0' LED indicates normal level,
yellow '+6' indicates normal peaks, and the red 'PEAK' LED warns of
potential overload 5dB before clipping.
The mix meters above each output fader monitors the pre-fade mix level.
You can run the mix 'hot' but reduce the channel fader levels if the red
'PEAK' LEDs flash.
LEVEL DIAGRAM
16
MONO INPUT
+48V - Feeds +48V to pins 2 and 3 of the input XLR for condenser
microphones which require phantom power.
Plug the microphone in before switching +48V on or off. Use +48V
only with balanced microphones and cables. No damage will occur
when +48V is switched to balanced non-phantom powered transformer
coupled dynamic microphones. However, always switch +48V off when
connecting line or unbalanced sources.
PHASE REVERSE - Reverses XLR input pins 2 and 3 to correct for
reverse wired cables or reversed phase signals. Can also be effective in
minimising acoustic feedback between the microphone and loudspeakers
in live sound mixing.
MIC/LINE (PAD) - Selects line input sensitivity when pressed, microphone
when released. Note that with the line jack unplugged the switch acts as
a 20dB pad for high output microphones or line input on XLR.
GAIN - Use this control with the MIC/LINE switch to adjust the channel
input sensitivity to match the connected source (-60 to +14dBu) to the
console operating level (0dBu). The gain should be set so that the channel
meter reads an average '0'.
LO-CUT FILTER - Reduces low frequency source noise such as
microphone proximity popping, stage noise and transport rumble. Can be
used to clean up sounds that do not have much bass content such as
vocals (around 150Hz), separate out the top end of a drum kit (400Hz),
reduce the handling noise of acoustic instruments, and so on. Select the
required cut off frequency by sweeping from fully anticlockwise (filter off)
to the maximum 400Hz. Setting the cutoff to 50Hz will have little effect on
most program material but will protect the low frequency speaker drivers.
The response drops by 12dB per octave below the cut off frequency.
EQUALISER - This provides separate, simultaneous control of 4
frequency bands. Each band may be boosted or cut by up to +/- 15dB
centred on the selected frequency which may be swept across a wide
range. Use the equaliser to correct for tonal deficiencies in the source
such as acoustic resonances or poor microphone response (corrective
EQ), or to change the tonal balance, for example to brighten up a guitar
so it cuts through the mix (effective EQ). You may need to adjust the input
GAIN control when using excessive amounts of EQ to compensate for the
change in overall signal level.
HF and LF affect the high (treble) and low (bass) frequencies respectively.
These have a shelving response which means that all frequencies beyond
the selected frequency are affected.
MF1 and MF2 affect the upper and lower mid frequencies respectively.
These have a peak/dip (bell shaped) response which means that the
maximum boost or cut occurs at the selected (center) frequency. The
MF1 and MF2 bands overlap for additional cut or boost when required or
to provide a tailored frequency response to suit any application. The
sharpness of the curve is selected using the Q switch to a Q of either 1
(wide band) or 2.4 (narrow band). Use wide band when you want to add
presence or warmth to the sound. Use narrow band to control problem
frequencies for example when notching out acoustic resonances.
(
17
AUXILIARY SENDS - Route the channel signal to one or
more of 10 auxiliary send busses. These are independent
from the main outputs and may be used for effects sends
and monitor mixes. The sends are grouped 1-4, 5-8, and 9-
10. Each group may be selected pre or post channel fader.
A further 6dB of boost above 0dB normal channel level is
available on the send control.
Use post-fade for effects sends such as reverb. The amount
of signal sent to the effects unit follows the fader level and
mute switch. The processed ("wet") signal returned to the
mix through the return channel is therefore in proportion to
the direct ("dry") signal from the fader to the mix.
Use pre-fade for monitor sends such as to on-stage monitor,
backstage, orchestra pit, and musicians cue speakers. The
amount of signal in the monitor mix is independent of the
fader level. Pre-fade sends are post-EQ, post-mute as
standard. (may be configured pre-EQ or pre-mute by setting
internal links).
DIRECT OUT - The 0dBu post-fade channel signal is
available at the DIR OUT jack socket. For pre/post selection
and independent level control select the underpanel #
DIR OUT mode switch. The 9-10 pre/post switch and aux 10
send control now affect the direct out signal. Select POST
for an effects send dedicated to that channel (local effect)
without tying up a complete aux buss. Select PRE for a
multitrack recording send with independent level control.
MUTE - When illuminated the channel signal is turned off
(muted). This affects both pre and post fade signals unless
the pre-fade aux has been internally configured pre-mute.
The silent action mute element can be controlled by the
switch, mute groups, mute patches or via MIDI. The green
SAFE/PREVIEW LED indicates if the channel has been
made 'safe' so that it is not affected by the mute groups,
patches or MIDI. It is also used when previewing or editing
the groups and patches.
ROUTING and PAN - The PAN control positions the
channel signal in the stereo mix. The post-pan signal may
be routed directly to the L-R mix or to the groups in odd/even
pairs. The groups may be used to feed additional outputs or
recording tracks, or for subgrouping combinations of
channel signals to the mix so that the overall level of the
group can be controlled without affecting the balance between
the signals, for example the drum kit mics. The pre-pan
signal may be routed to the MONO output independent of the
stereo positioning.
METER and PFL - The peak reading meter displays the
channel signal pre-fader. Use this to monitor signal presence
and level. The signal should average around '0' with the
loudest peaking at '6'. If the red PEAK light flashes the signal
level is too high (5dB below clipping) and should be reduced
using the GAIN control to prevent possible overload distortion.
Press PFL to listen to the pre-fade signal on headphones or
engineers monitor without affecting the main outputs.
18
STEREO INPUT
The stereo channel has two independent input sections: XLR IN for mono
microphone or line input, and STEREO LINE IN on jacks for sources such
as stereo keyboards, voice modules and effects returns. When using the
channel as a mono XLR mic/line input the stereo line input can be
independently routed to L-R for a stereo effects return or additional line
input. The XLR inputs on adjacent channels can be patched into a stereo
line when using stereo or paired microphones.
XLR MIC/LINE INPUT - This section is the same as the mono channel
input except that it has only the XLR input for both mic or line. It uses the
same wide ranging balanced pre-amp stage and includes the swept lo-cut
filter and insert. Refer to the MONO INPUT section for a detailed
description of these controls.
STEREO LINE INPUT - The left/mono and right inputs feed a balanced
pre-amp stage with GAIN variable from fully off to +10dB boost. Press ØR
to reverse the phase of the right input signal to correct phase differences
between the inputs. the WIDTH control is normally set to the centre
detented position for normal stereo. Turn anticlockwise to narrow the
stereo image until it becomes mono. Continue anticlockwise to open up
the stereo image but with left and right reversed. Turning clockwise from
centre accentuates the stereo effect by producing a phase enhanced
"wide" image. Press PFL to listen to the stereo signal on headphones or
local monitor without affecting the main outputs.
DIRECT TO L-R routes the stereo line signal to L-R independent of the
main stereo channel which you may be using as a mic/line XLR input. The
GAIN control adjusts the level to L-R. PFL lets you check the post-gain,
post-width stereo signal independent of the main channel PFL.
XLR/STEREO selects the input source to the main stereo channel. When
pressed the stereo line input is selected, when released the XLR mic/line
input is selected.
EQUALISER - This provides separate, simultaneous stereo control of 4
frequency bands. Each band may be boosted or cut by up to +/- 15dB. HF
and LF have a shelving response and affect the high (treble) and low
(bass) frequencies respectively. MF1 and MF2 have a peak/dip (bell
shaped) response and affect the upper and lower mid frequencies
respectively. MF1 is centred on 2.5kHz (presence) and MF2 is centred on
250Hz (warmth). Careful use of the equaliser can go a long way to
brightening up the sound of your stereo instruments, or tuning out the
noise characteristic of many lower cost effects units.
AUXILIARY SENDS - 10 aux sends are provided. These work in the
same way as the mono channel. Note that the left and right signals are
combined as mono aux sends. No direct output facility is available.
ROUTING, PAN, METER and PFL - These are the same as on the mono
channel. When a stereo input is selected PAN acts as a balance control
to adjust the level of the left and right signals relative to each other. The
meter indicates the pre-fade left and right signals combined. PFL
operates in stereo so that you can hear the image of the stereo source and
check the relative levels on the L and R meters.
19
STEREO MICROHONES
This example shows two
cardiod microphones arranged
as an X-Y coincident pair. This
minimises the phase
differences which can cause
problems when the mics are
arranged as a spaced pair.
The mic input stages are
patched into a stereo line input
for single fader control. The
second stereo channel may be
used for an independent line
input.
ABOVE AND BELOW MICROPHONES
Here, two microphones are
used on the snare drum to get
the best balance between stick
sound and skin resonance on
top, and snare sound below.
Reversing the phase of the
lower mic can compensate for
the opposite skin resonance
between the mics. Signal
processing such as noise
gates can be patched in as
shown.
The M-S stereo configuration is often
preferred when simultaneous mono feeds
are derived from the stereo signal. Here,
a cardiod and a figure-of-8 mic are
positioned on the same stand. The
cardiod picks up the "middle" (mono)
signal, and the figure-of-8 the "side"
(stereo content). Stereo is extracted
from the mic signals by producing sum
and difference channels. When
combined the stereo content is cancelled
out leaving true mono. Balance the two
faders to achieve the desired image.
M-S STEREO MICROPHONES
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

Allen-Heath ML4000 User manual

Category
Audio mixers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI