Trendnet Industrial Single Board Computer HS-6038 User manual

HS-6038

Socket 370 133MHz FSB

Industrial Single Board Computer

•Full-size•All-in-One•CompactFlash•

•

133MHz FSB

•

CRT

•

Dual LAN

•

Audio

•

•ATA/33/66/100•RS-232/422/485•PC/104•

•

IrDA

•

USB

•

DOC

•

WDT

•

H/W Monitor

•

•PICMG Bus Industrial Single Board Computer•

Copyright Disclaimers

The accuracy of contents in this manual has passed thorough checking and review

before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is

not liable for any infringements of patents or other rights resulting from its use. The

manufacturer will not be responsible for any direct, indirect, special, incidental

or consequential damages arising from the use of this product or

documentation, even if advised of the possibility of such damage(s).

This manual is copyrighted and BOSER Technology Co., Ltd. reserves all

documentation rights. Unauthorized reproduction, transmission, translation,

and storage of any form and means (i.e.,

electronic, mechanical, photocopying,

recording) of this document, in whole or partly, is prohibited, unless granted

permission by BOSER Technology Co., Ltd.

BOSER Technology Co., Ltd. reserves the right to change or improve the

contents of this document without due notice.

BOSER Technology Co., Ltd.

assumes no responsibility for any errors or omissions that may appear in this

manual, nor does it make any commitment to update the information contained

herein.

T

r

a

d

e

m

a

r

k

s

BOSER is a registered trademark of BOSER Technology Co., Ltd.

ISB is a registered trademark of BOSER Technology Co., Ltd.

Intel is a registered trademark of Intel Corporation.

AMI is a registered trademark of American Megatrends, Inc.

Award is a registered trademark of Award Software, Inc.

All other trademarks, products and or product names mentioned herein are

mentioned for identification purposes only, and may be trademarks and/or

registered trademarks of their respective companies or owners.

Version 1.0, May 06, 2004

Table of Contents

Chapter 1 General Description…………………...1

1.1

Major Features.................................................................. 2

1.2

Specifications ................................................................... 3

1.3

Board Dimensions............................................................ 4

Chapter 2 Unpacking……………………………..5

2.1

Opening the Delivery Package........................................ 5

2.2

Inspection.......................................................................... 5

Chapter 3 Hardware Installation………………...7

3.1

Before Installation ............................................................ 7

3.2

Board Layout .................................................................... 8

3.3

Jumper List ....................................................................... 9

3.4

Connector List .................................................................. 9

3.5

Configuring the CPU ...................................................... 10

3.6

System Memory .............................................................. 10

3.7

VGA Controller ............................................................... 10

3.8

IDE Drive Connector ...................................................... 11

3.9

Floppy Disk Drive Connector ........................................ 12

3.10

Serial Port Connectors .................................................. 12

3.11

Parallel Connector.......................................................... 13

3.12

Ethernet Connector........................................................ 14

3.13

IrDA Connector............................................................... 14

3.14

USB Connector............................................................... 15

3.15

CMOS Data Clear............................................................ 15

3.16

Power and Fan Connectors........................................... 16

3.17

Keyboard/Mouse Connectors ....................................... 17

3.18

System Front Panel Connectors................................... 17

3.19

External Speaker ............................................................ 18

3.20

Thermal Input Connectors............................................. 18

3.21

Audio Connectors .......................................................... 19

3.22

SMI Signal Input Switch................................................. 19

3.23

Watchdog Timer ............................................................. 20

3.24

CompactFlash



Connector........................................... 21

3.25

PC/104 Connectors ........................................................ 22

3.26

DiskOnChip



Address Setting ..................................... 25

Chapter 4 AMI BIOS Setup……………………..27

4.1

Starting Setup ................................................................. 27

4.2

Using Setup..................................................................... 28

4.3

Main Menu ....................................................................... 29

4.4

Standard CMOS Setup ................................................... 30

4.5

Advanced CMOS Setup ................................................. 31

4.6

Advanced Chipset Setup ............................................... 32

4.7

Power Management Setup ............................................ 33

4.8

PCI / Plug and Play Setup.............................................. 34

4.9

Peripheral Setup............................................................. 35

4.10

Hardware Monitor Setup................................................ 36

4.11

Auto-Detect Hard Disks ................................................. 37

4.12

Change Supervisor/User Password ............................. 38

4.13

Auto Configuration with Optimal Settings .................. 39

4.14

Optimal Configuration with Fail Safe Settings............ 40

4.15

Save Settings and Exit................................................... 41

4.16

Exit Without Saving........................................................ 42

Chapter 5 Software Utilities…………………….43

5.1

IDE Driver Installation .................................................... 43

5.2

VGA Driver Installation .................................................. 49

5.3

LAN Driver Installation................................................... 55

5.4

Audio Driver Installation................................................ 74

Safety Instructions

Integrated circuits on computer boards are sensitive to static electricity.

To avoid damaging chips from electrostatic discharge, observe the

following precautions:

 Do not remove boards or integrated circuits from their anti-static

packaging until you are ready to install them.

 Before handling a board or integrated circuit, touch an unpainted portion

of the system unit chassis for a few seconds. This helps to discharge any

static electricity on your body.

 Wear a wrist-grounding strap, available from most electronic component

stores, when handling boards and components. Fasten the ALLIGATOR

clip of the strap to the end of the shielded wire lead from a grounded

object. Please wear and connect the strap before handle the HS-6038 to

ensure harmlessly discharge any static electricity through the strap.

 Please use an anti-static pad when putting down any components or

parts or tools outside the computer. You may also use an anti-static bag

instead of the pad. Please inquire from your local supplier for additional

assistance in finding the necessary anti-static gadgets.

NOTE:

DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE

COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC

PROTECTION.

1

Chapter 1

General Description

The HS-6038 is a 133MHz FSB Intel

®

82815/82801BA chipset-based

board designed for PICMG Bus Celeron™/Coppermine™/Tualatin™

800MHz~1.2GHz CPU compatibility. These features combine and

make the HS-6038 an ideal all-in-one industrial single board computer.

Additional features include an enhanced I/O with CompactFlash, VGA,

dual LAN, audio, and two COM interfaces.

Its onboard ATA/33/66/100 to connected IDE drive interface

architecture allows the HS-6038 to support data transfers of 33, 66 or

100MB/sec. for each IDE drive connection. Designed with the Intel

®

82815/82801BA core logic chipset, the board supports all

Celeron™/Coppermine™/Tualatin™ CPU series operating at 800MHz

to 1.2GHz. The 82815 integrated CRT display controller supports up to

1280 x 1024 at 16 color resolution.

A single Flash chip holds the system BIOS, and you can change the

Flash BIOS by the Utility Update. Advanced IrDA port also provides a

faster data transmission. You can also use the DOS version of the

“DiskOnChip

TM

” socket by issuing commands from the DOS prompt

without the necessity of other software supports up to 288MB. System

memory is also sufficient with the two DIMM sockets that can support

up to 512MB.

2

Additional onboard connectors include an advanced USB and IrDA

ports providing faster data transmission, and a dual RJ-45 connector

for 10/100 Based Ethernet use.

To ensure the reliability in an unmanned or standalone system

, the

Watchdog Timer (WDT) onboard HS-6038 is designed with pure

hardware that does not need the arithmetical functions of a real-time

clock chip. If any program causes unexpected halts to the system, the

onboard Watchdog Timer (WDT) will automatically reset the CPU or

generate an interrupt to resolve such condition.

The HS-6038 also has a CompactFlash

TM

connector that

accommodates standard of memory cards available in the market.

1.1 Major Features

The HS-6038 comes with the following features:

 Socket 370 for Intel

®

Celeron



/Coppermine



/Tualatin



800MHz

~1.2GHz CPU

 Supports 66/100/133MHz FSB

 Two DIMM sockets with a max. capacity of 512MB

 Intel

®

82815/82801BA system chipset

 Winbond W83627 super I/O chipset

 Intel



82815 CRT display controller

 Intel



82559 and ICHII 10/100 Based LAN

 AC97 3D audio controller

 Two COM, four USB connectors

 PC/104 Bus connector

 DiskOnChip

TM

socket supporting memory sizes of up to 288MB

 Supports Hardware Monitor

 Supports CompactFlash

TM

card reader (optional)

3

1.2 Specifications

 CPU: Socket 370 for Intel



Celeron/Coppermine/Tualatin 800MHz

~1.2GHz CPU

 Bus Interface: PICMG Bus

 Memory: Two DIMM sockets supporting up to 512MB

 Chipset: Intel

®

82815/82801BA

 I/O Chipset: Winbond W83627

 CompactFlash



: One, IDE interface adapter (optional)

 VGA: Intel



82815 supporting CRT display up to 1280 x 1024 at 16 colors

 LAN: Intel

®

82559 and Intel

®

ICHII 10/100 Based LAN

 Audio: AC97 3D audio controller



IDE:

Four IDE disk drives supporting ATA/33/66/100 and with transfer

rates of up to 33/66/100MB/sec.

 FDD: Supports up to two floppy disk drives

 Parallel: One enhanced bi-directional parallel port supporting

SPP/ECP/EPP

 Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232

x 1 serial ports with 16-byte FIFO

 PC/104: PC/104 connector for 8-bit ISA Bus

 IrDA: One TX/RX IrDA header

 USB: Four USB connectors

 Keyboard/Mouse: PS/2 6-pin Mini DIN

 DiskOnChip: DiskOnChip socket supporting memory sizes of up to

288MB

 BIOS: AMI PnP Flash BIOS

 Watchdog Timer: Software programmable time-out intervals from

1~256 sec.

 CMOS: Battery backup

 Power Consumption: +5V/7.5A (1GHz CPU), +12V/120mA

 Operating Temperature: 0~60°C

 Hardware Monitor: Winbond W83627

 Board Size: 33.8 x 12.1 cm

4

1.3 Board Dimensions

5

Chapter 2

Unpacking

2.1 Opening the Delivery Package

The HS-6038 is packed in an anti-static bag. The board has

components that are easily damaged by static electricity. Do not

remove the anti-static wrapping until proper precautions have been

taken. Safety Instructions in front of this manual describe anti-static

precautions and procedures.

2.2 Inspection

After unpacking the board, place it on a raised surface and carefully

inspect the board for any damage that might have occurred during

shipment. Ground the board and exercise extreme care to prevent

damage to the board from static electricity.

Integrated circuits will sometimes come out of their sockets during

shipment. Examine all integrated circuits, particularly the BIOS,

processor, memory modules, ROM-Disk, and keyboard controller chip

to ensure that they are firmly seated. The HS-6038 delivery package

contains the following items:

 HS-6038 Industrial Single Board Computer

 ATA/100 IDE flat cable x 2

 FDD flat cable x 1

 Printer cable with bracket x 1

 KB/MS transfer cable x 1



8-pin USB split type cable with bracket x 1

 Speaker connector flat cable with bracket x 1

 Two RS-232 cable with bracket x 1

 5-pin ATX cable x 1

 Jumper Bag

 Utility CD-ROM

 User’s Manual

6

It is recommended that you keep all the parts of the delivery package

intact and store them in a safe/dry place for any unforeseen event

requiring the return shipment of the product. In case you discover any

missing and/or damaged items from the list of items, please contact

your dealer immediately.

7

Chapter 3

Hardware Installation

This chapter provides the information on how to install the hardware

using the HS-6038. This chapter also contains information related to

jumper settings of switch, watchdog timer, and the DiskOnChip



address selection etc.

3.1 Before Installation

After confirming your package contents, you are now ready to install

your hardware. The following are important reminders and steps to

take before you begin with your installation process.

1. Make sure that all jumper settings match their default settings

and CMOS setup correctly. Refer to the sections on this chapter

for the default settings of each jumper.

2. Go through the connections of all external devices and make

sure that they are installed properly and configured correctly

within the CMOS setup. Refer to the sections in this chapter for

the detailed information on the connectors.

3. Keep the manual and diskette in good condition for future

reference and use.

8

3.2 Board Layout

9

3.3 Jumper List

Jumper Definition Setting

Page

JP2 Host Bus Clock Rate Select: 133MHz FSB Open 10

JP3 Clear CMOS: Normal Operation Short 1-2 15

JP4 LAN2 Enabled/Disabled Select: Enabled Short 1-2 14

JP5

WDT Active Type Setting: System Reset Short 2-3 20

JP6 Short 3-4 25

JP7

DiskOnChip Address Select: 0D000H~

0D1FFH

Short 1-2 25

JP8 / JP9 /

JP11 / JP12

COM 2 Use RS-232 or RS-422/485 Select:

RS-232

Short 2-3

12

3.4 Connector List

Connector Definition Page

ATX1 20-pin ATX Power In Connector 16

CD1 CD-ROM Analog Input Connector 19

CD2

Line In Connector 19

CN1 Keylock Connector 17

CN2 Speaker Connector 18

CN3 5-pin Keyboard Connector 17

CN4 HDD LED Connector 17

CN5

SMI Signal Input Connector 19

CN6 2-pin ATX Power On Switch 16

CN7 2-pin Reset Button Connector 17

CN8 Fan Power In Connector 16

CN9 I

2

C Bus Connector 10

CN10 5-pin ATX Power In Connector 16

CN11 COM 1 Connector (5x2 header) 12

CN12 RS-422/485 Connector (5x2 header) 12

CN13 COM 2 Connector (5x2 header) 12

CF1 CompactFlash

TM

Connector 21

DIM1/DIM2 168-pin DIMM Sockets 10

FDC1 Floppy Connector 12

IDE1/IDE2 Primary/Secondary IDE Connectors 11

IR1 IrDA Connector 14

JP1 System Sensing Connector 18

JP13 MIC In / Audio Out Connector 19

KB1 PS/2 6-pin Mini DIN KB/MS Connector 17

LAN1 Dual RJ-45 Connector 14

LPT1

Parallel Connector 13

…More on next page…

10

Connector Definition Page

PC1 / PC2 PC/104 Bus 64-pin/40-pin Connectors 22

USB1 External USB Connector 15

USB2/USB3 Internal USB Connectors 15

RT1/RT2 Power Sensing Connectors 18

VGA1

15-pin VGA Connector 10

3.5 Configuring the CPU

JP2 is used to set the Host Bus Clock Rate. The setting of internal Host

Bus Clock Rate is for defining the operating clock base rate of the

internal bus of core logic.



JP2: Host Bus Clock Rate Select

Description Setting

66/100MHz FSB Short

133MHz FSB (default) Open

1

2

3.6 System Memory

The HS-6038 provides two 168-pin DIMM sockets at locations DIM1

and DIM2. The maximum capacity of the onboard memory is 512MB.

3.7 VGA Controller

The HS-6038 provides one connection for VGA device. VGA1 offers a

single standard 15-pin CRT connector.



VGA1: 15-pin CRT Connector

PIN Description PIN Description

1 Red 2 Green

3 Blue 4 VCC

5 GND 6 GND

7 GND 8 GND

9 VCC 10 GND

11 VCC 12 DDCDA

13 HSYNC 14 VSYNC

15 DDCCL

1

6

10

11

5

15

An Inter-IC connector CN9, also offers the flexibility of installing an I

2

C

digital signal-based device.

11



CN9: I

2

C Bus Connector

PIN Description

1 SMBDATA

2 SMBCLK

3

GND

123

3.8 IDE Drive Connector

IDE1/IDE2 are standard 40-pin connector daisy-chain driver

connectors serving the PCI E-IDE drive provisions onboard the

HS-6038. A maximum of four IDE drives can be connected to the

HS-6038 via IDE1/IDE2.



IDE1/IDE2: Primary/Secondary IDE Connectors

PIN Description PIN Description

1 RESET 2 GND

3 DATA 7 4 DATA 8

5

DATA 6

6

DATA 9

7 DATA 5 8 DATA 10

9 DATA 4 10 DATA 11

11 DATA 3 12 DATA 12

13 DATA 2 14 DATA 13

15

DATA 1

16

DATA 14

17 DATA 0 18 DATA 15

19 GND 20 N/C

21 PDREQ 22 GND

23 PDIOW# 24 GND

25 PDIOR# 26 GND

27 PIORDY 28 GND

29 RPDACK- 30 GND

31 IRQ14 32 N/C

33 RPDA1- 34 PATA66DET

35 RPDA0- 36 RPDA2-

37 RPCS1- 38 RPCS3-

39 HDD ACTIVE 40 GND

1

2

40

39

3 5 7 9 17 19 21 23 25 27 29 31

33

11 13 15 35 37

46810

18

20

22

24 26

28

30

32 34

12 14

16 36

38

12

3.9 Floppy Disk Drive Connector

The HS-6038 uses a standard 34-pin header connector, FDC1, for

floppy disk drive connection. A total of two floppy drives may be

connected to FDC1 at any given time.



FDC1: Floppy Connector

PIN Description PIN Description

1 GND 2 RWC-

3 GND 4 N/C

5 GND 6 DS1-

7

GND

8

Index#

9

GND

10

Motor Enable A#

11 GND 12 Drive Select B#

13 GND 14 Drive Select A#

15 GND 16 Motor Enable B#

17 GND 18 Direction#

19 GND 20 Step#

21 GND 22 WD-

23 GND 24 WE-

25 GND 26 Track 0#

27 GND 28 WP-

29 N/C 30 RDATA-

31 GND 32 HEAD-

33 N/C 34 DSKCHG-

34

33

1

2

u

3.10 Serial Port Connectors

The HS-6038 offers one NS16C550 compatible UARTs with

Read/Receive 16-byte FIFO serial ports.



CN11, CN13: COM1/COM2 Connectors (5x2 header)

PIN Description

1 DCD 2 DSR

3 RXD 4 RTX

5

TXD

6

CTX

7 DTR 8 RI

9 GND 10 N/C

246810

13579

13



CN12: RS-422/485 Connector (5x2 header)

PIN Descriptio

n

PIN Description

1 TX- 2 TX+

3 RX+ 4 RX-

5 GND 6 RTS-

7 RTS+ 8 CTS+

9 CTS- 10 N/C

246810

13579

TX+

RX-

RTS-

N/C

CTS+

TX-

RX+

GND

CTS-

RTS+



JP8/JP9/JP11/JP12: COM2 Use RS-232 or RS-422/485 Select

Options Settings

RS-232 (default)

Short 2-3

RS-422/485 Short 1-2

13

3.11 Parallel Connector

LPT1 is a standard 26-pin flat cable connector designed to

accommodate parallel port connection onboard the HS-6038.



LPT1: Parallel Connector

PIN Description PIN Description

1 Strobe 2 DATA 0

3 DATA 1 4 DATA 2

5

DATA 3

6

DATA 4

7 DATA 5 8 DATA 6

9 DATA 7 10 Acknowledge

11 Busy 12 Paper Empty

13 Printer Select 14 Auto Form Feed

15 ERROR# 16 Initialize

17 Printer Select LN# 18 GND

19 GND 20 GND

21 GND 22 GND

23 GND 24 GND

25 GND 26 GND

1

14

26

13

14

3.12 Ethernet Connector

The HS-6038 provides one dual RJ-45 10/100 Based LAN interface

connectors. Please refer to the following table for their identical pin

assignments.



LAN1: Dual RJ-45 Connector

Description

1 1TX+ 2 1TX-

3

1RX+

4

1R/C GND

5 1R/C GND 6 1RX-

7 1R/C GND 8 1R/C GND

9 2TX+ 10 2TX-

11 2RX+ 12 2R/C GND

13

2R/C GND

14

2RX-

15 2R/C GND 16 2R/C GND

1R/C GND

8

7

2

1

1RX-

1R/C GND

1RX+

1TX+

1TX-

2R/C GND

16

15

10

9

2RX-

2R/C GND

2RX+

2TX+

2TX-



JP4: LAN2 Enable/Disable Select

Options Settings

Enabled (default) Short 1-2

Disabled Short 2-3

123

3.13 IrDA Connector

IR1 is a 5-pin internal IR communication connector for connection of an

IrDA device.



IR1: IrDA Connector

PIN Description

1 VCC

2

N/C

3 IRRX

4 GND

5 IRTX

12345

Page is loading ...

Trendnet Industrial Single Board Computer HS-6038, HS-6038 User manual

Other documents