Toshiba U200/PORTG M500 User manual

GB-1

GB

TOSHIBA Bluetooth Module

Installation

This sheet provides information on installing the Bluetooth module in the

Satellite U200/PORTÉGÉ M500/Satellite Pro U200/TECRA M6.

Installing the Bluetooth module

1. Turn off the power - ensure that the Power indicator is off.

2. Remove all cables and peripherals that are connected to the computer.

3. Close the display panel and turn the computer upside down.

4. Remove the battery pack from the computer. For instructions on

removing the battery pack, refer to Chapter 6 in the online manual.

5. Remove ten screws.

Figure 1: Removing ten screws

This sheet is for information only. The Bluetooth module must be installed

by dealers of TOSHIBA or TOSHIBA OEM products.

Discharge static electricity from your body by touching a metal object,

before you handle the card.

Use a point size zero screwdriver.

BT_061215.fm Page 1 Monday, December 18, 2006 5:41 PM

GB-2

6. Turn the computer right side up and open the display panel.

7. Insert a thin object under the rim of the keyboard brace and lift it out.

8. Remove two screws securing the keyboard.

9. Lift up the back of the keyboard, rotate it toward you and lay in face

down on the palm rest.

Figure 2: Removing the keyboard brace and two screws

10. Remove one screw securing the keyboard support plate, lift the plate up

and out to remove it.

11. Disconnect the keyboard flexible cable from the connector and remove

the keyboard.

Figure 3: Removing the keyboard support plate and the keyboard

When you move the keyboard forward, do not touch the keys. Doing so

could cause misalignment. Hold the keyboard by the sides and lay it

gently on the palm rest. The keyboard is connected to the computer by the

keyboard flexible cable. Be careful not to apply tension to this cable when

you lift up the keyboard.

Keyboard brace

Screws

Keyboard support plate

Screw

Keyboard

BT_061215.fm Page 2 Monday, December 18, 2006 5:41 PM

GB-3

12. Peel off the insulators and disconnect three flexible cables from the

connectors.

Figure 4: Removing the insulators and the flexible cables

13. Remove two screws.

Figure 5: Removing two screws

14. Remove the cover assembly.

Figure 6: Removing the cover assembly

Flexible cable

Flexible cables

Insulators

Screws

Cover assembly

BT_061215.fm Page 3 Monday, December 18, 2006 5:41 PM

GB-4

15. Connect the antenna cable to the Bluetooth module.

16. Connect one end of the flexible cable to the Bluetooth module.

17. Connect the other end of the flexible cable to the connector on the

computer.

18. Seat the Bluetooth module and secure it with one flat-head screw.

Figure 7: Connecting the flexible cable and antenna cable

19. Seat the cover assembly and secure two screws.

20. Connect three flexible cables and apply two new insulators.

21. Place the keyboard as its face down on the palm rest and connect the

keyboard flexible cable.

22. Seat the keyboard support plate and secure one screw.

23. Seat the keyboard and secure two screws.

24. Seat the keyboard brace and press to secure latches.

25. Close the display panel and turn the computer upside down.

26. Secure ten screws.

27. Install the battery pack.

Hold the Bluetooth module by the sides only. Do not touch the connector

on the card or on the computer. Debris on the connectors may cause

access problems. Be careful not to apply pressure to the ICs on the

Bluetooth module.

Fold up a flexible cable after seating the Bluetooth module.

Flat-head screw

Bluetooth module

Antenna cable

Flexible

cable

When applying insulators, do not reuse the removed insulators. Use new

ones.

BT_061215.fm Page 4 Monday, December 18, 2006 5:41 PM

GB-5

Applying labels

The following figure shows the locations of labels.

Label positions

The letters A, B and C correspond to labels identified in later illustrations.

The applied labels will vary according to your computer’s configuration.

Figure 8: Label positions

New labels

Refer to figures above and below when you apply new labels.

1. Remove the battery pack. Refer to Chapter 6 in the online manual for

details.

2. Apply the Bluetooth label to position B.

3. Apply the Wireless LAN label to position A.

4. Apply the Singapore Regulatory label to position C. If your computer

already has the Singapore Regulatory label, you do not need to apply a

new label.

AB

C

BT_061215.fm Page 5 Monday, December 18, 2006 5:41 PM

GB-6

These labels are samples.

Figure 9: Bluetooth label

Figure 10: Wireless LAN labelBluetooth label

Figure 11: Singapore Regulatory label

BT_061215.fm Page 6 Monday, December 18, 2006 5:41 PM

Page is loading ...

DE-8

BT_061215.fm Page 8 Thursday, December 21, 2006 2:34 AM

Page is loading ...

ES-6

Estas etiquetas son muestras.

Figura 9: Etiqueta de Bluetooth

Figura 10: Etiqueta de LAN inalámbrica

Figura 11: Etiqueta de la legislación para Singapur

BT_061215.fm Page 6 Thursday, December 21, 2006 2:55 AM

Page is loading ...

NL-6

Deze labels zijn voorbeelden.

Afbeelding 9: Bluetooth-label

Afbeelding 10: Wireless LAN-label Bluetooth-label

Afbeelding 11: Officieel etiket voor Singapore

BT_061215.fm Page 6 Thursday, December 21, 2006 3:04 AM

Toshiba U200/PORTG M500 User manual

This manual is also suitable for

Toshiba U200/PORTG M500 User manual

in other languages

Related papers

Other documents