Briggs & Stratton 280000 User manual

280000
Briggs & Stratton
Brand
Briggs & Stratton
Model
280000
Category
Motor vehicle accessories & components
Type
User manual
Operator’s Manual
BRIGGSandSTRATTON.com
ECopyright Briggs & Stratton Corporation
Milwaukee, Wisconsin 53201 U.S.A.
Form No. 276344-3/07
Printed in U.S.A.
Models Covered in This
Manual Include Gasoline,
Natural Gas and Liquid
Propane Gas Engines
Model 210000
Power Built
Intek
I/C
Model 280000
Intek
I/C
Extended Life Series
Model 310000
Intek
I/C
Extended Life Series
2
TABLE OF CONTENTS
Safety 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Information 5. . . . . . . . . . . . . . . . . . . . . . . . . .
Oil 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel and Starting Information 7. . . . . . . . . . . . . . . . .
Starting and Stopping 8-9. . . . . . . . . . . . . . . . . . . . . .
Maintenance 10-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts and Service & Storage 15. . . . . . . . . . . . . . . . .
Warranty Information 16-18. . . . . . . . . . . . . . . . . . . .
For replacement parts or technical assistance, record below the engine model, type, and code numbers along with the date of
purchase. These numbers are located on your engine (see the “Engine Information” page).
Date of purchase:
Engine model:
MM/ DD/YYYY
Model: Code:Type:
BEFORE OPERATING ENGINE
• Read entire Operating & Maintenance Instructions
AND the instructions for the equipment this engine
powers.*
• Failure to follow instructions could result in serious
injury or death.
THE OPERATING & MAINTENANCE INSTRUC-
TIONS CONTAIN SAFETY INFORMATION TO
• Make you aware of hazards associated with engines
• Inform you of the risk of injury associated with those
hazards, and
• Tell you how to avoid or reduce the risk of injury.
* Briggs & Stratton does not necessarily know what equipment this engine will power. For that reason, you should carefully
read and understand the operating instructions for the equipment on which your engine is placed.
The safety alert symbol ( ) is used to identify safety
information about hazards that can result in personal injury.
A signal word (DANGER, WARNING, or CAUTION) is
used with the alert symbol to indicate the likelihood and the
potential severity of injury. In addition, a hazard symbol
may be used to represent the type of hazard.
DANGER indicates a hazard which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, might result in minor or moderate
injury.
CAUTION, when used without the alert symbol,
indicates a situation that could result in damage
to the engine.
WARNING
The engine exhaust from this
product contains chemicals known
to the State of California to cause
cancer, birth defects, or other
reproductive harm.
HAZARD SYMBOLS AND MEANINGS
Explosion
Toxic Fumes
Moving Parts
ShockHot Surface
Kickback
Fire
THE INTERNATIONAL SYMBOLS USED
ON THE ENGINE OR
IN THIS MANUAL INCLUDE:
On Off
Fuel Shutoff
Read Owner’s
Manual
Stop Fuel
Choke
Safety Alert
Oil
Frostbite
Wear Eye Protection
3
SAFETY
Fuel and its vapors are extremely flammable
and explosive.
Fire or explosion can cause severe burns or
death.
WARNING
WHEN FUELING
• Turn engine OFF and let engine cool at least 2 minutes
before removing cap or refueling engine.
• Fill fuel tank outdoors or in well-ventilated area.
• On GASOLINE operated engines, do not overfill fuel
tank. Fill tank to approximately 1-1/2 inches below top of
neck to allow for fuel expansion.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap, and fittings frequently for
cracks or leaks. Replace if necessary.
WHEN STARTING ENGINE
• Make sure spark plug, muffler, fuel cap and air cleaner
are in place, and firmly secured by equipped fasteners.
• Do not crank engine with spark plug, air cleaner cartridge
or air cleaner cover removed.
• If fuel spills, wait until it evaporates before starting engine.
• If GASOLINE engine floods, set choke to OPEN/RUN
position, place throttle in FAST and crank until engine
starts.
WHEN OPERATING EQUIPMENT
• Do not tip engine or equipment at angle which causes
gasoline to spill.
• Do not choke carburetor to stop engine.
WHEN TRANSPORTING EQUIPMENT
• On GASOLINE engine, transport with fuel tank EMPTY or
with fuel shut-off valve OFF.
• On NATURAL / LIQUID PETROLEUM (LP) GAS
engines transport with fuel cylinder empty or valve
closed, or tank disconnected.
WHEN STORING GASOLINE OR EQUIPMENT WITH
FUEL IN TANK
• Store away from furnaces, stoves, water heaters or other
appliances that have pilot light or other ignition source
because they can ignite gasoline vapors.
WARNING
Gaseous fuels are extremely flammable
and readily form explosive air-vapor mix-
tures at ambient temperatures.
IF YOU SMELL GAS:
• DO NOT start the engine.
• DO NOT actuate any electrical switches.
• DO NOT use the phone in the vicinity.
• Evacuate the area.
• Contact the gas supplier or fire department.
REMEMBER:
• LPG vapor is heavier than air and trends to collect in low
areas. NG vapor is lighter than air and tends to collect in
high areas. Both may travel to remote locations.
• Keep all flames, sparks, pilot lights, and other ignition
sources away from the area where the engine is operated
or repaired.
• DO NOT smoke when operating or repairing the engine.
• DO NOT store gasoline or other flammable vapors or
liquids in the vicinity of the engine.
• BEFORE doing any service work to the engine, shut off
the gas supply.
• After initial installation or servicing, check for gas leaks.
DO NOT use an open flame. Apply very soapy water or
leak test solution with a brush and look for bubbles.
• Keep the equipment and the area surrounding the engine
free of debris.
• Install the fuel system according to applicable fuel/gas
codes.
WARNING
Wear eye protection when doing repair work.
Frostbite can result from skin/eye contact with
leaking LP liquid.
• Installation, adjustment and repair work should be done by a
qualified technician.
• Flexible supply lines should be checked regularly to make
sure they are in good condition. Replace damaged or
leaking components.
4
SAFETY
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
WARNING
• If there is natural or LP gas leakage in area, do not start
engine.
• Do not use pressurized starting fluids because vapors
are flammable.
WARNING
• When starting engine, pull cord slowly until resistance is
felt, then pull rapidly.
• Remove all external equipment/engine loads before
starting engine.
• Direct coupled equipment components such as, but not
limited to, blades, impellors, pulleys, sprockets, etc.,
must be securely attached.
Rapid retraction of starter cord (kickback) will pull
hand and arm toward engine faster than you can
let go.
Broken bones, fractures, bruises or sprains could
result.
WARNING
Rotating parts can contact or entangle hands,
feet, hair, clothing, or accessories.
Traumatic amputation or severe laceration can
result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling drawstrings or
items that could become caught.
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting or death.
WARNING
• Start and run engine outdoors.
• Do not start or run engine in enclosed area, even if doors
or windows are open.
WARNING
Running engines produce heat. Engine parts,
especially muffler, become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass,
brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before
touching.
• Remove accumulated combustibles from muffler area
and cylinder area.
• Install and maintain in working order a spark arrester
before using equipment on forest-covered, grass-cov-
ered, brush-covered unimproved land. The state of
California requires this (Section 4442 of the California
Public Resources Code). Other states may have similar
laws. Federal laws apply on federal land.
WARNING
Unintentional sparking can result in fire or
electric shock.
Unintentional start-up can result in entangle-
ment, traumatic amputation, or laceration.
BEFORE PERFORMING ADJUSTMENTS OR REPAIRS
• Disconnect spark plug wire and keep it away from spark
plug.
• Disconnect battery at negative terminal (only engines
with electric start).
WHEN TESTING FOR SPARK
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
5
ENGINE INFORMATION
1. Oil drain
2. Oil fill/Dipstick
3. Rotating screen
4. Air cleaner handle
5. Muffler/(Muffler guard (if equipped)/
(Spark arrester, if equipped)
6. 12 V electric starter (if equipped)
7. Rewind starter handle (if equipped)
8. Fuel pump (if equipped)
9. In-line fuel filter (if equipped)
10. Carburetor or LPG / NG Mixer
11. Oil filter (if equipped)
12. Air cleaner cover
13. Spark plug wire
14. Engine
Model Type Code
xxxxx xxxx xx xxxxxxxx
7
11
12
9
8
10
2
3
4
6
1
5
13
14
GENERAL INFORMATION
ENGINE MODEL: This is a single cylinder, overhead valve
(OHV), air-cooled engine. It is a low emissions engine.
In the state of California, OHV Models 210000, 280000 and
310000 engines are certified by the California Air Resources
Board to meet emissions standards for 250 hours. Such
certification does not grant the purchaser, owner or operator of this
engine any additional warranties with respect to the performance
or operational life of this engine. This engine is warranted solely
according to the product and emissions warranties stated
elsewhere in this manual.
TUNE-UP SPECIFICATIONS
Armature air gap 0.010 − 0.014 in. (0.25 − 0.36 mm). . . . . . . . .
Spark plug gap 0.030 in. (0.76 mm). . . . . . . . . . . . . . . . . . . . . . . .
Valve clearance with valve springs installed and piston 1/4 in.
(6 mm) past top dead center (check when engine is cold). See
Repair Manual P/N 272147.
Intake 0.003 − 0.005 in. (0.08 − 0.13 mm). . . . . . . . . . . . . . . . . . .
Exhaust 0.005 − 0.007 in. (0.13 − 0.18 mm). . . . . . . . . . . . . . . . .
MODEL 210000
Bore 3.44 in. (87.31 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke 2.27 in. (57.66 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement 21 cu. in. (344 cc). . . . . . . . . . . . . . . . . . . . . . . . . . .
MODEL 280000
Bore 3.44 in. (87.31 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke 3.06 in. (77.78 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement 28.42 cu. in. (466 cc). . . . . . . . . . . . . . . . . . . . . . . .
MODEL 310000
Bore 3.56 in. (90.60 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke 3.06 in. (77.78 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displacement 30.59 cu. in. (501 cc). . . . . . . . . . . . . . . . . . . . . . . .
Note: For practical operation, the horsepower loading should not
exceed 85% of rated horsepower. Engine power will decrease
3-1/2% for each 1,000 feet (300 meters) above sea level and 1%
for each 10° F (5.6° C) above 77° F (25° C). Engine will operate
satisfactorily at an angle up to 15°.
TECHNICAL INFORMATION
Engine Power Rating Information
The gross power rating for individual gas engine models is
labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 (Small Engine Power & Torque Rating
Procedure), and rating performance has been obtained and
corrected in accordance with SAE J1995 (Revision 2002-05).
Torque values are derived at 3060 RPM; horsepower values
are derived at 3600 RPM. Actual gross engine power will be
lower and is affected by, among other things, ambient operating
conditions and engine-to-engine variability. Given both the wide
array of products on which engines are placed and the variety
of environmental issues applicable to operating the equipment,
the gas engine will not develop the rated gross power when
used in a given piece of power equipment (actual “on-site” or
net power). This difference is due to a variety of factors
including, but not limited to, accessories (air cleaner, exhaust,
charging, cooling, carburetor, fuel pump, etc.), application
limitations, ambient operating conditions (temperature, humidity,
altitude), and engine-to-engine variability. Due to manufacturing
and capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this Series engine.
6
OIL
CAUTION: This engine is shipped from Briggs &
Stratton without oil
. Check oil level before starting
engine. If you start the engine without oil, the engine
will be damaged beyond repair and will not be
covered under warranty.
OIL CAPACITY
Engine without oil filter:
Approximately 44 ounces (1.30 liters)
Engine with oil filter:
Approximately 48 ounces (1.42 liters)
TYPE OF OIL TO USE
• Use a high quality detergent oil classified “For Service
SF, SG, SH, SJ” or higher, such as Briggs & Stratton
30W, Part Number 100005 (20 oz) or 100028 (48 oz).
• Do not use special additives.
• Choose a viscosity according to the table opposite.
Note: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol
(shown at left) with “SJ/CF ENERGY CON-
SERVING” or higher, is an acceptable oil at all
temperatures. Use of synthetic oil does not
alter required oil change intervals.
°F
-20 0 20 40 60 80 100
°C
-30 -20 -10 0 10 20 30 40
STARTING TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
*
**
32
* CAUTION: Air cooled engines run hotter than
automotive engines. The use of non-synthetic
multi-viscosity oils (5W-30, 10W-30, etc.) in
temperatures above 40° F (4° C) will result in higher
than normal oil consumption. When using a
multi-viscosity oil, check oil level more frequently.
** CAUTION: SAE 30 oil, if used below 40° F (4° C), will
result in hard starting and possible engine bore
damage due to inadequate lubrication.
SAE Viscosity Grades
CHECKING AND ADDING OIL
• Check oil level before starting the engine.
• Check level daily, or after every eight (8) hours.
• Keep oil level at FULL.
• Do not overfill.
[1] Place engine level and clean around oil fill area.
[2] Remove dipstick and wipe clean with cloth.
[3] Replace and tighten dipstick. Remove and check oil level.
[4] Oil level should be at FULL line on dipstick.
[5] If needed, add oil slowly - recheck. Do not over fill.
[6] Replace and tighten dipstick.
7
[1] Remove cap. Fill tank to approximately 1-1/2
inches below top of neck to allow for fuel
expansion. Be careful not to overfill.
[2] Replace cap before starting.
FUEL
TYPE OF FUEL TO USE
• Use clean, fresh, regular unleaded gasoline with a
minimum of 85 octane. Fresh fuel prevents gum from
forming in the fuel system or on essential carburetor parts.
Purchase fuel in quantity that can be used within 30 days.
• Do not use gasoline which contains Methanol.
• Do not mix oil with gasoline.
• For engine protection use Briggs & Stratton Gasoline
Additive available from your Authorized Briggs &
Stratton Dealer (P/N 5041 or single use pouch).
• The gasoline engine is certified to operate on gasoline.
Exhaust Emission Control System: EM (Engine
Modifications).
• Turn engine OFF and let engine cool at least
2 minutes before removing gas cap.
• Fill fuel tank outdoors or in well-ventilated
area.
• Keep gasoline away from sparks, open
flames, pilot lights, heat, and other ignition
sources.
• If fuel spills, wait until it evaporates before
starting engine.
CAUTION: Some fuels, called oxygenated or
reformulated gasoline, are gasoline blended with
alcohols or ethers. Excessive amounts of these
blends can damage the fuel system or cause
performance problems. If any undesirable operat-
ing symptoms occur, use gasoline with a lower
percentage of alcohol or ether.
GASOLINE POWERED ENGINES
NATURAL / LIQUID PROPANE GAS
POWERED ENGINES
• Use clean, dry fuel, free of moisture or any particulate
material. Using fuels outside the following recom-
mended values may cause performance problems.
• In engines set up to run on LPG, commercial grade
HD5 LPG is recommended. Recommended fuel
composition is fuel with a minimum fuel energy of
2500 BTU’s/ft
3
with maximum propylene content of
5% and butane and heavier gas content of 2.5% and
minimum propane content of 90%.
• NG or LPG engines are certified to operate on natural
or liquid propane gas.
The equipment on which this engine is
mounted is equipped with an automatic
safety gas “fuel lock-off” valve. DO
NOT operate the equipment if the “fuel
lock-off” valve is missing or
inoperative.
WARNING
ADDING FUEL
GASOLINE POWERED ENGINES
• Read the operating instructions supplied by the
equipment manufacturer for information on refueling
natural or LP gas engine.
NATURAL / LIQUID PROPANE GAS
POWERED ENGINES
WARNING
8
STARTING
WARNING
• Do not use pressurized starting fluids.
• Vapors are flammable.
WARNING
• DO NOT start engine with air filter or
cover not properly installed. Serious injury
or death could result from backfire.
OIL PRESSURE SWITCH
If engine is equipped with an oil pressure switch, the switch
will either activate a warning light or stop the engine when
the engine runs low on oil. (Read the operating instructions
supplied by the equipment manufacturer to determine
which way your engine is equipped because the equipment
manufacturer supplies the oil pressure gauge.)
♦ Store and fuel equipment in level position.
♦ Use fresh fuel. (See Fuel.)
♦ Use correct type of oil for expected starting
temperature. (See Oil.)
♦ Remove external equipment/engine loads. (See
equipment operating instructions.)
♦ Start lawn mower on hard surface or over
previously cut grass.
♦ Periodically remove grass buildup under mower
deck. (See Maintenance.)
♦ After engine has started, let it warm up several
seconds to several minutes, depending on outside
temperature.
♦ For maximum performance and life, operate
engine with choke in RUN and throttle in FAST.
STARTING AND OPERATING TIPS
BEFORE STARTING
[1] Check oil level.
NATURAL / LIQUID PROPANE GAS
POWERED ENGINES
[1] Check oil level.
[2] Open fuel
shut-off valve
(if equipped).
[3] If choke and
throttle controls
are separate,
move choke
control to
CHOKE. Move
throttle to FAST.
[4] If choke and
throttle are on the
same control,
move control to
CHOKE or
START.
Choke Throttle
Combined Choke/Throttle
control
1/4 TURN
GASOLINE POWERED ENGINES
9
STARTING
[1] Insert key and turn to START.
CAUTION:
To prolong starter life, use short starting
cycles (5 seconds maximum, then wait one
minute). Follow equipment manufacturer’s
recommendations for charging battery.
[2] Let engine warm up.
If choke equipped: Slowly adjust
toward RUN position. Wait until
engine runs smoothly before each
choke adjustment.
ELECTRIC (KEY) STARTER
WARNING
[3] Let engine warm up.
If choke equipped: Slowly adjust toward RUN position. Wait
until engine runs smoothly before each choke adjustment.
REWIND (MANUAL) STARTER (auxiliary)
[1] Insert key (if equipped) and turn to RUN.
[2] Grasp rope handle. Pull slowly until resistance is felt, then
pull rapidly to start engine and avoid kickback.
STOPPING
[1] With throttle in FAST, turn key to OFF.
[2] Remove key and store out of reach of children.
[3] Close fuel shut-off valve (if equipped).
1/4 TURN
CAUTION:
Do not stop engine by moving choke control to CHOKE.
Backfire, fire or engine damage could occur.
10
MAINTENANCE
MAINTENANCE
Regular maintenance will improve the performance and
extend the life of the engine. See any Authorized Briggs &
Stratton Dealer for service. Use only genuine Briggs &
Stratton parts. Other parts may not perform as well,
may damage the engine, and may result in injury. In
addition, use of other parts may void your warranty.
EMISSION CONTROL
Maintenance, replacement or repair of the emission
control devices and systems may be performed by any
nonroad engine repair establishment or individual.
However, to obtain no charge repairs under the terms and
provisions of the Briggs & Stratton warranty statement, any
service or emission control part repair or replacement must
be performed by a factory authorized dealer.
Task
Perform task at hourly
or calendar interval,
whichever comes first.
Every 8 Hours
or Daily
25 Hours or
Every Season
50 Hours or
Every Season
100 Hours or
Every Season
Yearly
200 Hours or
Every Season
Check Oil Level
Change Oil *
Change oil filter
(if equipped)
*
Service air cleaner
pre-cleaner (if equipped)
**
Replace air cleaner car-
tridge (if not equipped
with pre-cleaner)
**
Replace air cleaner car-
tridge (if equipped with
pre-cleaner)
**
Clean Extended Life
Series™ air cleaner car-
tridge
**
Replace Extended Life
Series™
air cleaner cartridge
**
Inspect spark arrester
(if equipped)
Replace spark plug
Replace in-line fuel filter
(if equipped)
Clean cooling system **
Check valve clearance
Check valve clearance
on NG / LPG Engines
* Change oil after first 5 to 8 hours of use, then every
50 hours or every season. Change oil every 25 hours
when operating the engine under heavy load or in high
temperatures.
** Clean more often under dusty conditions or when
airborne debris is present. Replace air cleaner parts, if
very dirty.
CHANGING OIL
[1] Place engine level.
[2] Disconnect spark plug
wire and keep away from
spark plug. Disconnect
battery (if equipped with
electric starter) at nega-
tive terminal.
[3] With engine OFF but still warm remove oil drain
plug and drain oil into appropriate receptacle.
[4] Reinstall drain plug. Remove dipstick.
[5] Fill to FULL mark on dipstick with new oil.
Do not overfill.
[6] Replace dipstick.
OIL DRAIN
PLUG
TO REMOVE
Typical drain
plugs
7/16” PIPE
5/16” HEX
3/8” SQUARE
WARNING
CAUTION: Used oil is a hazardous waste product.
Dispose of used oil properly. Do not discard with
household waste. Check with your local authorities,
service center, or dealer for safe disposal/recycling
facilities.
11
MAINTENANCE
AIR CLEANER
CAUTION: Do not use pressurized air or solvents to clean cartridge. Pressurized air can damage cartridge;
solvents will dissolve cartridge.
FLAT AIR CLEANER REMOVAL/ INSTALLATION
[1] Pull up on air cleaner cover handle, and rotate toward
engine.
[2] Remove air cleaner cover.
[3] Carefully lift air cleaner cartridge and pre-cleaner, if
equipped, from blower housing.
Note: To clean pre-cleaner, wash in soapy water. Squeeze
dry in a clean cloth. DO NOT OIL.
[4] Clean base of air cleaner cartridge area carefully to
prevent debris from entering engine.
[5] Place air cleaner pre-cleaner, if equipped, and cartridge
into blower housing. Cartridge must fit securely in base.
[6] Align tabs on cover with slots of blower housing and
replace cover.
[7] Hook handle and close cover.
If filters, or covers are not installed
correctly serious injury or death
could result from backfire. Do not
attempt to start your engine with
them removed.
WARNING
EXTENDED LIFE SERIESE CARTRIDGE ONLY
This filter,
IF STAMPED
‘WASHABLE’, can
be washed with
warm water and
mild soap.
IMPORTANT:
Rinse in tap water
with SCREEN side
up allowing dirt
and debris to filter
out.
Leave filter to dry
overnight before
reinstalling.
COVER
PRE-CLEANER
(if equipped)
TABS
CARTRIDGE
SLOTS
12
MAINTENANCE
HIGH FLOW AIR CLEANER MAINTENANCE
Perform this maintenance every 25 hours or every season,
clean more often under dusty conditions or when airborne
debris is present. This filter is made of cotton, which is
different from a standard paper filter, therefore it MUST be
oiled.
[1] Remove clamp and pull air cleaner from intake
manifold.
[2] Remove as much dirt from the filter as possible.
[3] Using the High Flow Air Filter Cleaner Kit, Briggs &
Stratton part no. 5089D, spray the filter with cleaner.
Allow the solution to soak in to the filter for about 15
minutes.
CAUTION: Never use strong detergents, high
pressure water, or gasoline to clean this filter.
[4] Rinse the filter with warm water, inside first and then
outside. (Let the water run from the clean side to the
dirty side.)
[5] Allow the filter to dry completely. It is best to allow the
filter to dry naturally. Don’t use heat, this might shrink
the cotton.
[6] Use only air filter oil, such as the oil included in the
cleaning kit (P/N 5089D), to re-oil the filter.
WARNING
Never use motor oil, transmission fluid, WD40, or other
oils. Failure to follow instructions can cause fires
resulting in death or serious injury. Use only air filter oil
designed specifically for air filters.
[7] Spray the filter with oil, or pour small amount onto
each pleat and allow filter to stand for 20 minutes. The
filter is correctly oiled when the cotton changes from
white to the color of the oil.
CAUTION: DO NOT over-oil air filter, it will interfere
with engine performance and may cause engine
damage. If the filter is placed on cardboard for 10
minutes and leaves a stain, it is over oiled. Wash/clean
and re-oil per above instructions.
[8] Re-install air filter.
CARBURETOR
CLAMP
HIGH FLOW
AIR FILTER
FILTER
P/N 698973
OIL FILTER (IF EQUIPPED)
Replace oil filter after every 100 hours of operation.
[1] Drain engine oil and remove oil filter.
[2] Before installing new filter, lightly oil filter gasket with
fresh, clean engine oil.
[3] Screw filter on by hand until gasket contacts oil filter
adapter. Tighten 1/2 to 3/4 turn more.
[4] Add fresh oil. Fill to FULL line on dipstick.
[5] Start and run engine at idle to check for oil leaks.
[6] Stop engine. Recheck oil level and add oil if required.
OIL PRESSURE
If oil pressure drops too low, an oil pressure switch (if
engine is equipped) will either activate a warning light or
stop the engine. Check oil level with dipstick. If oil level is
between ADD and FULL mark on dipstick, Do not try to
restart engine. Contact an Authorized Briggs & Stratton
Service Dealer. Do not operate engine until oil pressure is
corrected.
If oil level is below ADD mark on dipstick, add oil to bring
level to FULL mark. Restart engine and check oil pressure.
If pressure is normal, continue to operate engine.
Note: Oil pressure gauge, if engine is equipped, is supplied
by manufacturer of equipment.
13
MAINTENANCE
ENGINE AND ENGINE PARTS
We recommend that you see an authorized Briggs & Stratton Service Dealer for all maintenance and service of the engine
and engine parts. Use only genuine Briggs & Stratton parts.
WARNING
If you perform any maintenance on the engine, first disconnect the spark plug wire
from the spark plug, and disconnect the battery at the negative terminal (electric
starter engines only) to prevent unintentional sparking. Unintentional sparking can
result in fire or electric shock. Unintentional start-up can result in entanglement,
traumatic amputation or laceration. Use only correct tools.
WARNING
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
• Do not tamper with governor spring, links or other parts to increase engine speed.
Replacement parts for the muffler
must be the same and installed in the
same position as the original parts,
otherwise fire can occur.
WARNING
If muffler is equipped with spark arrester screen, remove
screen for inspection. Replace screen if damaged or
plugged.
MUFFLER
SPARK PLUG
Use only Briggs & Stratton Spark Tester (part number
19368) to check for spark.
Check the spark plug every season. Replace the spark plug
if upon inspection the electrodes are burned or worn.
Ensure the spark plug is clean. Check the gap with a feeler
gage and reset to 0.030 in. (0.76 mm) if necessary.
Note: In some areas, local law requires using resistor
spark plug to suppress ignition signals. If this engine was
originally equipped with resistor spark plug, use same
type for replacement.
.030” (0.76 mm)
WIRE GAGE
REPLACE FUEL FILTER (if equipped)
WARNING
EXTENDED LIFE SERIES™ FUEL FILTER
PART NO. 695666 OR 5070
(WITH FUEL PUMP)
Drain fuel tank or close
fuel shut-off valve before
replacing fuel filter.
Otherwise, fuel can leak
out, creating a fire/ex-
plosion hazard.
STANDARD FUEL FILTER
FUEL HOSE
CLAMPS
PART NO. 298090 OR 5018
(WITHOUT FUEL PUMP)
PART NO. 394358
(WITH FUEL PUMP)
Debris may clog the engine’s air cooling system. Remove
blower housing and clean area shown to prevent
overheating and engine damage.
AIR COOLING SYSTEM
CLEAN OUT CHAFF AND
DEBRIS
14
MAINTENANCE
CLEANING DEBRIS
Engine parts should be kept clean to
reduce the risk of overheating and
ignition of accumulated debris. This is
especially important if cutting tall grass.
WARNING
CAUTION: Do not use water to clean engine parts.
Water could contaminate fuel system. Use a brush
or dry cloth.
Finger Guard
CLEAN
CLEAN
Rotating Screen
Daily or before every use, clean grass, chaff or accumu-
lated debris from engine. Keep linkage, spring and
controls clean. Keep area around and behind muffler free
of any combustible debris.
Linkage, Springs,
Controls
CLEAN
CLEAN
Muffler,
Spark Arrester
15
SERVICE & STORAGE
PARTIAL LIST OF BRIGGS & STRATTON PARTS
Models 280000, 310000 AVSE series
Extended Life SeriesE flat air cleaner cartridge 697153
(washable, no pre-cleaner required)
Extended Life SeriesE Maintenance Kit 5128. . . . . . . .
(Includes oil, A/C filter, spark plug, gas additive)
Flat air cleaner cartridge and pre-cleaner kit 5077. . . . .
Flat air cleaner cartridge 698083. . . . . . . . . . . . . . . . . . . .
Flat air cleaner pre-cleaner 697015. . . . . . . . . . . . . . . . . .
Maintenance Kit 5127. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Includes oil, A/C filter, spark plug, gas additive)
UL Approved flat air cleaner cartridge 790263. . . . . . . . .
(For NG/LPG Gaseous Fuel engines.)
Model 210000 AVSE series
Flat air cleaner cartridge and pre-cleaner kit 5079. . . . .
Flat air cleaner cartridge 698413. . . . . . . . . . . . . . . . . . . .
Flat air cleaner pre-cleaner 697292. . . . . . . . . . . . . . . . . .
Maintenance Kit 5126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Includes oil, A/C filter, spark plug, gas additive)
Oval air cleaner cartridge and pre-cleaner kit 5053. . . .
Oval air cleaner cartridge 496894. . . . . . . . . . . . . . . . . . . .
Oval air cleaner pre-cleaner 272403. . . . . . . . . . . . . . . . . .
High Flow Air Filter (cylinder) 698973. . . . . . . . . . . . . . . .
High Flow Air Filter Cleaning Kit 5089D. . . . . . . . . . . . . . .
Synthetic Oil (32 oz.) 100074. . . . . . . . . . . . . . . . . . . . . . .
Oil (20 oz.) 100005. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil (48 oz.) 100028. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil filter (3-1/2 in. long) 491056. . . . . . . . . . . . . . . . . . . . . .
Oil filter (2-1/4 in. long) 492932. . . . . . . . . . . . . . . . . . . . . .
Fuel filter 298090 -or- 5018. . . . . . . . . . . . . . . . . . . . . . . . .
(for engines without fuel pump installed)
Extended Life Series™ fuel filter 695666 -or- 5070. . . . . .
(for engines equipped with fuel pump)
Fuel filter 394358. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(for engines equipped with fuel pump)
Gas additive 5041. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resistor spark plug 491055. . . . . . . . . . . . . . . . . . . . . . . . .
Long life platinum spark plug 5066. . . . . . . . . . . . . . . . . . .
(used on most OHV engines)
Spark plug wrench 89838 -or- 5023. . . . . . . . . . . . . . . . . . .
Spark tester 19368. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil pump kit 5056. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(uses standard electric drill to remove oil from engine quickly)
SERVICE
See an Authorized Briggs & Stratton Service Dealer. Each
one carries a stock of Genuine Briggs & Stratton Parts and
is equipped with special service tools. Trained mechanics
assure expert repair service on all Briggs & Stratton
engines. Only dealers advertising as “Authorized Briggs &
Stratton” are required to meet Briggs & Stratton standards.
When you purchase equipment powered by a
Briggs & Stratton engine, you are assured of
highly skilled, reliable service at more than
30,000 Authorized Service Dealers
worldwide, including more than 6,000 Master
Service Technicians. Look for these signs
wherever Briggs & Stratton service is offered.
You may locate your nearest Authorized Briggs & Stratton
Service Dealer in our dealer locator map on our web site
www.briggsandstratton.com or in the “Yellow Pages™”
directory under “Engines, Gasoline” or “Gasoline
Engines,” or “Lawn Mowers” or similar category.
Note: Walking fingers logo and “Yellow Pages” are regis-
tered trademarks in various jurisdictions.
™
An illustrated shop manual includes
common specifications and detailed
information covering adjustment,
tune-up and repair of Briggs & Strat-
ton single cylinder, OHV, 4 cycle
engines. It is available for purchase
from an Authorized Briggs & Stratton
Service Dealer or you can order it
from the factory. Write:
Briggs & Stratton Corporation
Attn: Service Division
P. O. Box 1144
Milwaukee, WI 53201
Part No. 272147
STORAGE
Engines stored over 30 days need special attention.
[1] To prevent gum from forming in fuel system or on
essential carburetor parts:
a) if fuel tank contains oxygenated or reformulated
gasoline (gasoline blended with an alcohol or an
ether), run engine until it stops from lack of fuel, or b) if
fuel tank contains gasoline, either run engine until it
stops from lack of fuel, or add a gasoline additive to the
gas in the tank. (See parts list. Single − use pouches of
gas additive are available from your service dealer.) If
you use a gas additive, run the engine for several
minutes to circulate the additive through the carburetor.
Then, engine and fuel can be stored up to 24 months.
[2] While engine is still warm, change oil.
[3] Remove spark plug and pour about 1 oz. (30 ml) of
engine oil into cylinder. Replace spark plug and crank
slowly to distribute oil.
[4] Clean engine of surface debris, chaff or grass.
WARNING
[5] Store in a clean, dry area.
Do not store in same area
as a stove, furnace, water
heater, or other appliance
that uses a pilot light or
has a device that can
create a spark.
16
BRIGGS & STRATTON ENGINE OWNER WARRANTY POLICY
Effective 12/06
Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the engine that is defective in material or workmanship or both.
Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective
for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our
dealer locator map at www.briggsandstratton.com, or by calling (800) 233-3723, or as listed in the ‘Yellow Pages™’.
There is no other express warranty, implied warranties, including those of merchantability and fitness for a particular purpose, are
limited to one year from purchase, or to the extent permitted by law any and all implied warranties are excluded. Liability for incidental
or consequential damages are excluded to the extent exclusion is permitted by law. Some states or countries do not allow limitations on how
long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary
from state to state and country to country.
LIMITED WARRANTY
WARRANTY TERMS **
Brand / Product Type Consumer Use Commercial Use
Vanguard 2 years 2 years
Extended Life Series, I / C, Intek I / C, Intek Pro 2 years 1 year
Kerosene Fuel Operated Engines 1 year 90 days
All Other Briggs & Stratton Engines 2 years 90 days
** Engines used on Home Standby Generator applications are warranted under consumer use only. This warranty does not
apply to engines on equipment used for prime power in place of a utility. Engines used in competitive racing or on
commercial or rental tracks are not warranted.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in
the table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including
use for commercial, income producing or rental purposes. Once an engine has experienced commercial use, it shall thereafter be considered as a
commercial use engine for purposes of this warranty.
No warranty registration is necessary to obtain warranty on Briggs & Stratton Products. Save your proof of purchase
receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing
date of the product will be used to determine the warranty period.
ABOUT YOUR WARRANTY
Briggs & Stratton welcomes warranty repair and apologizes to you for being
inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most
warranty repairs are handled routinely, but sometimes requests for warranty service
may not be appropriate. For example, warranty would not apply if engine damage
occurred because of misuse, lack of routine maintenance, shipping, handling,
warehousing or improper installation. Similarly, warranty is void if the serial number
of the engine has been removed or the engine has been altered or modified.
If a customer differs with the decision of the Service Dealer, an investigation will be
made to determine whether the warranty applies. Ask the Service Dealer to submit
all supporting facts to his Distributor or the Factory for review. If the Distributor or the
Factory decides that the claim is justified, the customer will be fully reimbursed for
those items that are defective. To avoid misunderstanding which might occur
between the customer and the Dealer, listed below are some of the causes of
engine failure that the warranty does not cover.
Normal wear:
Engines, like all mechanical devices, need periodic parts service and replacement to
perform well. Warranty will not cover repair when normal use has exhausted the life
of a part or an engine.
Improper maintenance:
The life of an engine depends upon the conditions under which it operates, and the
care it receives. Some applications, such as tillers, pumps and rotary mowers, are
very often used in dusty or dirty conditions, which can cause what appears to be
premature wear. Such wear, when caused by dirt, dust, spark plug cleaning grit, or
other abrasive material that has entered the engine because of improper
maintenance, is not covered by warranty.
This warranty covers engine related defective material and/ or workmanship
only, and not replacement or refund of the equipment to which the engine may
be mounted. Nor does the warranty extend to repairs required because of:
1 Problems caused by parts that are not original Briggs & Stratton parts.
2 Equipment controls or installations that prevent starting, cause unsatisfactory
engine performance, or shorten engine life. (Contact equipment manufacturer.)
3 Leaking carburetors, clogged fuel pipes, sticking valves, or other damage,
caused by using contaminated or stale fuel. (Use clean, fresh, lead-free
gasoline and Briggs & Stratton Fuel Stabilizer, Part No. 5041.)
4 Parts which are scored or broken because an engine was operated with
insufficient or contaminated lubricating oil, or an incorrect grade of lubricating oil
(check oil level daily or after every 8 hours of operation. Refill when necessary
and change at recommended intervals.) OIL GARD may not shut down running
engine. Engine damage may occur if oil level is not properly maintained. Read
Operating & Maintenance Instructions.
5 Repair or adjustment of associated parts or assemblies such as clutches,
transmissions, remote controls, etc., which are not manufactured by Briggs &
Stratton.
6 Damage or wear to parts caused by dirt, which entered the engine because of
improper air cleaner maintenance, re-assembly, or use of a non-original air
cleaner element or cartridge. (At recommended intervals, clean and re-oil the
Oil-Foam
element or the foam pre-cleaner, and replace the cartridge.) Read
Operating & Maintenance Instructions.
7 Parts damaged by over-speeding, or overheating caused by grass, debris, or
dirt, which plugs or clogs the cooling fins, or flywheel area, or damage caused
by operating the engine in a confined area without sufficient ventilation. (Clean
fins on the cylinder, cylinder head and flywheel at recommended intervals.)
Read Operating & Maintenance Instructions.
8 Engine or equipment parts broken by excessive vibration caused by a loose
engine mounting, loose cutter blades, unbalanced blades or loose or
unbalanced impellers, improper attachment of equipment to engine crankshaft,
over-speeding or other abuse in operation.
9 A bent or broken crankshaft, caused by striking a solid object with the cutter
blade of a rotary lawn mower, or excessive v-belt tightness.
10 Routine tune-up or adjustment of the engine.
11 Engine or engine component failure, i.e., combustion chamber, valves, valve
seats, valve guides, or burned starter motor windings, caused by the use of
alternate fuels such as, liquified petroleum, natural gas, altered gasolines, etc.
Warranty service is available only through service dealers which have been
authorized by Briggs & Stratton Corporation. Your nearest Authorized Service
Dealer is listed in the “Yellow Pages
™” of your telephone directory under
“Engines, Gasoline” or “Gasoline Engines,” “Lawn Mowers,” or similar
category.
17
Emissions Control System Warranty Statement
Briggs & Stratton Corporation (B&S), the California Air Resources Board (CARB) and the
United States Environmental Protection Agency (U.S. EPA) Emissions Control System
Warranty Statement (Owner’s Defect Warranty Rights and Obligations)
California, United States and Canada Emissions Control Defects
Warranty Statement
The California Air Resources Board (CARB), U.S. EPA and B&S are
pleased to explain the Emissions Control System Warranty on your small
off-road engine (SORE). In California, new small off-road engines model
year 2006 and later must be designed, built and equipped to meet the
State’s stringent anti-smog standards. Elsewhere in the United States,
new non-road, spark-ignition engines certified for model year 1997 and
later must meet similar standards set forth by the U.S. EPA. B&S must
warrant the emissions control system on your engine for the periods of
time listed below, provided there has been no abuse, neglect or improper
maintenance of your small off-road engine.
Your emissions control system includes parts such as the carburetor, air
cleaner, ignition system, fuel line, muffler and catalytic converter. Also
included may be connectors and other emissions related assemblies.
Where a warrantable condition exists, B&S will repair your small off-road
engine at no cost to you including diagnosis, parts and labor.
Briggs & Stratton Emissions Control Defects Warranty Coverage
Small off-road engines are warranted relative to emissions control parts
defects for a period of two years, subject to provisions set forth below. If
any covered part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities
As the small off-road engine owner, you are responsible for the
performance of the required maintenance listed in your Operating and
Maintenance Instructions. B&S recommends that you retain all your
receipts covering maintenance on your small off-road engine, but B&S
cannot deny warranty solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that
B&S may deny you warranty coverage if your small off-road engine or a
part has failed due to abuse, neglect, improper maintenance or
unapproved modifications.
You are responsible for presenting your small off-road engine to an
Authorized B&S Service Dealer as soon as a problem exists. The
undisputed warranty repairs should be completed in a reasonable amount
of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and
responsibilities, you should contact a B&S Service Representative at
(414) 259-5262.
The emissions warranty is a defects warranty. Defects are judged on
normal engine performance. The warranty is not related to an in-use
emissions test.
Briggs & Stratton Emissions Control Defects Warranty Provisions
The following are specific provisions relative to your Emissions Control Defects Warranty Coverage. It is in addition to the B&S engine warranty for
non-regulated engines found in the Operating and Maintenance Instructions.
1. Warranted Parts
Coverage under this warranty extends only to the parts listed below
(the emissions control systems parts) to the extent these parts were
present on the engine purchased.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor and internal parts
• Fuel pump
• Fuel line, fuel line fittings, clamps
• Fuel tank, cap and tether
• Carbon canister
b. Air Induction System
• Air cleaner
• Intake manifold
• Purge and vent line
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse valve
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and
switches
• Connectors and assemblies
2. Length of Coverage
B&S warrants to the initial owner and each subsequent purchaser
that the Warranted Parts shall be free from defects in materials and
workmanship which caused the failure of the Warranted Parts for a
period of two years from the date the engine is delivered to a retail
purchaser.
3. No Charge
Repair or replacement of any Warranted Part will be performed at no
charge to the owner, including diagnostic labor which leads to the
determination that a Warranted Part is defective, if the diagnostic
work is performed at an Authorized B&S Service Dealer. For
emissions warranty service contact your nearest Authorized B&S
Service Dealer as listed in the “Yellow Pages” under “Engines,
Gasoline,” “Gasoline Engines,” “Lawn Mowers,” or similar category.
4. Claims and Coverage Exclusions
Warranty claims shall be filed in accordance with the provisions of
the B&S Engine Warranty Policy. Warranty coverage shall be
excluded for failures of Warranted Parts which are not original B&S
parts or because of abuse, neglect or improper maintenance as set
forth in the B&S Engine Warranty Policy. B&S is not liable to cover
failures of Warranted Parts caused by the use of add-on,
non-original, or modified parts.
5. Maintenance
Any Warranted Part which is not scheduled for replacement as
required maintenance or which is scheduled only for regular
inspection to the effect of “repair or replace as necessary” shall be
warranted as to defects for the warranty period. Any Warranted Part
which is scheduled for replacement as required maintenance shall
be warranted as to defects only for the period of time up to the first
scheduled replacement for that part. Any replacement part that is
equivalent in performance and durability may be used in the
performance of any maintenance or repairs. The owner is
responsible for the performance of all required maintenance, as
defined in the B&S Operating and Maintenance Instructions.
6. Consequential Coverage
Coverage hereunder shall extend to the failure of any engine
components caused by the failure of any Warranted Part still under
warranty.
18
Look For Relevant Emissions Durability Period and
Air Index Information On Your Engine Emissions Label
Engines that are certified to meet the California Air Resources Board
(CARB) Tier 2 Emissions Standard must display information regarding
the Emissions Durability Period and the Air Index. Briggs & Stratton
makes this information available to the consumer on our emissions
labels. The engine emissions label will indicate certification information.
The Emissions Durability Period describes the number of hours of
actual running time for which the engine is certified to be emissions
compliant, assuming proper maintenance in accordance with the
Operating & Maintenance Instructions. The following categories are used:
Moderate:
Engine is certified to be emissions compliant for 125 hours of actual
engine running time.
Intermediate:
Engine is certified to be emissions compliant for 250 hours of actual
engine running time.
Extended:
Engine is certified to be emissions compliant for 500 hours of actual
engine running time. For example, a typical walk-behind lawn mower is
used 20 to 25 hours per year. Therefore, the Emissions Durability
Period of an engine with an intermediate rating would equate to 10 to 12
years.
Certain Briggs & Stratton engines will be certified to meet the United
States Environmental Protection Agency (USEPA) Phase 2 emissions
standards. For Phase 2 certified engines, the Emissions Compliance
Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet
Federal emissions requirements.
For engines less than 225 cc displacement.
Category C = 125 hours
Category B = 250 hours
Category A = 500 hours
For engines of 225 cc or more displacement.
Category C = 250 hours
Category B = 500 hours
Category A = 1000 hours
Briggs & Stratton Engines Are Made Under One Or More Of The Following Patents: Design D-247,177 (Other Patents Pending)
6,691,683
6,647,942
6,622,683
6,615,787
6,617,725
6,603,227
6,595,897
6,595,176
6,584,964
6,557,833
6,542,074
6,520,141
6,495,267
6,494,175
6,472,790
6,460,502
6,456,515
6,382,166
6,369,532
6,356,003
6,349,688
6,347,614
6,325,036
6,311,663
6,284,123
6,263,852
6,260,529
6,242,828
6,239,709
6,237,555
6,230,678
6,213,083
6,202,616
6,145,487
6,142,257
6,135,426
6,116,212
6,105,548
6,347,614
6,082,323
6,077,063
6,064,027
6,040,767
6,014,808
6,012,420
5,992,367
5,904,124
5,894,715
5,887,678
5,852,951
5,843,345
5,823,153
5,819,513
5,813,384
5,809,958
5,803,035
5,765,713
5,732,555
5,645,025
5,642,701
5,628,352
5,619,845
5,606,948
5,606,851
5,605,130
5,497,679
5,548,955
5,546,901
5,445,014
5,503,125
5,501,203
5,497,679
5,320,795
5,301,643
5,271,363
5,269,713
5,265,700
5,243,878
5,235,943
5,234,038
5,228,487
5,197,426
5,197,425
5,197,422
5,191,864
5,188,069
5,186,142
5,150,674
5,138,996
5,086,890
5,070,829
5,058,544
5,040,644
5,009,208
4,996,956
4,977,879
4,977,877
4,971,219
4,895,119
4,875,448
4,819,593
4,720,638
4,719,682
4,633,556
4,630,498
4,522,080
4,520,288
4,512,499
4,453,507
4,430,984
D 476,629
D 457,891
D 368,187
D 375,963
D 309,457
D 372,871
D 361,771
D 356,951
D 309,457
D 308,872
D 308,871
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Briggs & Stratton 280000 User manual

280000
Briggs & Stratton
Brand
Briggs & Stratton
Model
280000
Category
Motor vehicle accessories & components
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers