Altronix Pace1PRMT Installation guide

Brand: Altronix

Model: Pace1PRMT

Category: AV extenders

Type: Installation guide

Altronix Pace1PRMT extends the reach of your PoE or PoE+ network devices by transmitting data and power over a single twisted pair (UTP) or Cat5e cable. With a range of up to 500m (1,640 ft.) for Cat5e and 152m (500 ft.) for UTP, this device is ideal for connecting IP cameras, access points, and other PoE-powered devices in remote locations. It supports both 10/100BaseT Ethernet speeds and is compatible with IEEE 802.3af (15W) and IEEE 802.3at (30W) PoE standards. The Pace1PRMT also features LED indicators for power, PoE, and link status, making it easy to troubleshoot any issues.

Pace1PRMT - 1 -

Overview:

Pace1PRMT is a long range Ethernet adapter kit which transmits data at 100mbps full duplex and

power via a single twisted pair (UTP) or Cat5e or higher cable in a PoE(+) compliant format. The

Pace1PRM receiver is powered via a PoE midspan such as the Altronix Netway series or by an

endspan. The receiver passes the PoE(+) compliant power over the cable to the Pace1PTM trans-

ceiver which in turn passes this power to an enabled IP camera/device. These plug and play units

facilitate cost effective solutions for IP devices that need to be installed at distances greater than

100m. They also provide a simple way to replace legacy analog products with new IP devices over

single twisted pair (UTP) or structured cable.

Features:

Rev. 111413

Installation Guide

Pace1PRMT

IP and PoE+ Over Extended Distance UTP or CAT5e

Pace1PRM Receiver and Pace1PTM Transceiver kit

Agency Listings:

• UL/CUL Listed for Information

Technology Equipment (UL 60950-1).

• CE approved.

• C-Tick compliant.

Input (Pace1PRM):

• Powered by midspan or endspan.

PoE compliant to IEEE 802.3af (15W) and

PoE+ compliant to IEEE 802.3at (30W).

Ethernet:

• Connectivity: RJ45, auto-crossover.

• Wire type: 4-pair CAT5 or 1 pair UTP

structured cable.

• Distance: up to 500m (1,640 ft.).

• Speed: 10/100BaseT, half/full duplex, auto

negotiation. PoE compliant to IEEE 802.3af

(15W) and PoE+ compliant to IEEE 802.3at

(30W) delivered to camera by Pace1PTM.

Power provided by Pace1PRM to Pace1PTM

by PoE protocol.*

• Throughput is rated to pass 100mbps of

data at distances up to 500m with

proper headend equipment, this supports

Megapixel, HD720, HD1080.

CAT5e or higher:

• Distance: up to 500m @ 100mbps

(see Maximum Length of Cable Type vs.

Camera Power/PoE Class, pg. 4).

UTP (single pair):

• Distance: up to 152m @ 100mbps

(see Max. Length of Cable Type vs.

Camera Power/PoE Class, pg. 4).

LED Indicators:

• Pace1PRM/Pace1PTM:

Green - PoE ON (by respective RJ45 jack).

• Pace1PRM and Pace1PTM (RJ45 jack):

Yellow and Green LED IP Link status,

10/100Base-T/active.

Environmental:

• Operating Temperature

Pace1PRM/ Pace1PTM:

-- 20ºC to +49ºC (-- 4ºF to 120.2ºF).

• Storage Temperature:

-- 30º to +70ºC (-- 22º to 158ºF).

• Humidity: 20 to 85%, non-condensing.

Functions:

• Auto detection and protection of legacy

non-PoE cameras/devices.

Applications:

• Extend Network link distance in an

industrial environment over 700m

(see note, pg. 2).

• Retrofit digital IP cameras in an analog

CCTV CAT5e wired installations.

• Works with Megapixel, HD720, HD1080

and VGA (SD) cameras (see note, pg. 3).

Mechanical:

• Dimensions (W x L x H approx.):

Pace1PRM/Pace1PTM:

3.5” x 3.5” x 1”

(88.89mm x 88.89mm x 25.4mm).

I.T.E. 43KC

Z1409

* See note on page 3.

- 2 - Pace1PRMT

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and

with all local codes and authorities having jurisdiction. Wiring should be UL Listed and/or

Recognized wire suitable for the application.

Pace1PTM and Pace1PRM are not intended to be connected to outside plant leads and should be

installed indoors within the protected premises. Pace1PRM and Pace1PTM are intended for indoor

use only.

1. Pace1PRM installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit’s

mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet

switch/network, NVR or video server.

b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked

[PoE Input] (Fig. 2, pg. 3).

c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 OUT] (Fig. 2, pg. 3).

UTP: Connect single UTP to connector marked [UTP OUT] (Fig. 2, pg. 3).

2. Pace1PTM installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the case’s

mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device.

b. Connect structured cable from IP camera/device to RJ45 jack marked [PoE Out] (Fig. 2, pg. 3).

c. CAT5e or higher: Connect CAT5e or higher to connector marked [RJ45 IN] (Fig. 2, pg. 3).

UTP: For single UTP applications, jumpers (supplied) must be connected as follows:

1. Remove the four (4) screws from the Pace1PTM cover. Do not discard hardware.

2. Connect jumpers (supplied) to pins pairs [P5] and [P6] as shown (Figs. 1a & 1b, pg. 3).

3. Replace cover and secure it with the four (4) screws.

4. Connect UTP to connector marked [UTP IN].

Technical Specifications:

Parameter Description

Connections RJ45 for ethernet link or single pair UTP.

Input power

requirements

Midspan or endspan port connected.

PoE compliant to IEEE 802.3af (15W) and

PoE+ compliant to IEEE 802.3at (30W)

Indicators

Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.

Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.

Green: PoE Active.

Environmental

Conditions

Operating Ambient Temperature: UL60950-1

Pace1PRM: -- 20ºC to +49ºC (-- 4ºF to 120.2ºF).

Pace1PTM: -- 20ºC to +49ºC (-- 4ºF to 120.2ºF).

Relative humidity: 20 to 85%, non-condensing.

Storage Temperature: -- 30º to +70ºC (-- 22º to 158ºF).

Operating Altitude: -- 1000 to 6,561.679 ft. (-- 304.8 to 2000m).

Regulatory

Compliance

UL/CUL Listed for Information Technology Equipment (UL 60950-1).

CE approved. C-Tick compliant.

Weights (approx.) Product: 3.88 oz. (0.11 kg.), Shipping: 6.70 oz. (0.19 kg.)

Pace1PRMT - 3 -

Structured

Cable to

Midspan/

Endspan

Green LED

indicates

PoE Present

from Midspan/

Endspan

Green LED

indicates

PoE being

transmitted

to Pace1PTM

CAT5 or higher

from Pace1PTM

Single UTP

from

Pace1PTM

Structured

Cable from

Camera/Device

Green LED

indicates

PoE transmitted

to Camera/Device

Green LED

indicates

PoE received

from Pace1PRM

CAT5 or higher

from Pace

receiver

Single UTP

from

Pace1PRM

*Note: Caution, once PoE connection is established between Pace1PRM and Pace1PTM, discon-

nection from Pace1PTM will not disable the PoE output voltage on the Pace1PRM, although the

Pace1PTM can be reconnected, caution should be taken not to connect the CAT5e or single UTP

wiring from Pace1PRM to any non-PoE device.

PoE compliant

100m max.

Mounting Hole

PoE Camera

Pace1PTM

Pace1PRM

I.T.E. 43KC

RJ45

Link

Z1409

UTP

Link

RJ45 LEDs Yellow - Activity

Green - Speed

Green LED Power and PoE

PoE

Out

Output

PoE

LED

Input

PoE

LED

www.altronix.com

IP-UTP Transceiver

Passes PoE/PoE+

Pace1PTM - Transceiver

RJ45

Link

Output

PoE

LED

Input

PoE

LED

UTP

Link

PoE

Input

I.T.E. 43KC

Z1409

RJ45 LEDs Yellow - Activity

Green - Speed

Green LED Power and PoE

www.altronix.com

IP-UTP Receiver

Passes PoE/PoE+

Pace1PRM - Receiver

Structured Cable

or Single UTP

Legend:

PoE+ over CAT5e up to 500m max.

Single UTP up to 152.4m max.

Powered Switch or NetWay MidSpan

Single PoE Camera Connection Utilizing Pace1PRM and Pace1PTM:

Fig. 2 Fig. 2a

Pace1PRM

Pace1PTM

To access pins which are located behind

the UTP Link you must remove cover.

Note: Make sure jumpers are lined up

with pins pairs [F5] and [F6] as shown

in top and side views noted in

Figs. 1a & 1b.

Fig. 1

Fig. 1a Fig. 1b

Side View

Top View

UTP

Link

Jumper

P5 P6

- 4 - Pace1PRMT

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056

website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.

IIPace1PRMT K04O

MEMBER

PoE Camera

PoE+ over CAT5e up to 500m (1,640 ft.) max.

or Single UTP up to 152.4m (500 ft.) max.

PoE+ over CAT5e up to 500m (1,640 ft.) max.

or Single UTP up to 152.4m (500 ft.) max.

PoE+ over CAT5e up to 500m (1,640 ft.) max.

or Single UTP up to 152.4m (500 ft.) max.

PoE+ over CAT5e up to 500m (1,640 ft.) max.

or Single UTP up to 152.4m (500 ft.) max.

100m (328 ft.) max.

PoE compliant

100m (328 ft.) max.

PoE compliant

100m (328 ft.) max.

PoE compliant

100m (328 ft.) max.

PoE compliant

100m (328 ft.) max.

Structured Cable

or Single UTP

Legend:

Pace1PRM

Pace1PTM

Powered Switch or

NetWay MidSpan

Multiple PoE Cameras Connection:

Fig. 3

Maximum Length of Cable Type vs. Camera Power/PoE Class:

Cable Type

Total Power

Consumption

Max.

Data Distance

Max.

Power Distance

CAT5e

15W

500m

846m

30W 423m

Cable Type

Total Power

Consumption

Max.

Data Distance

Max.

Power Distance

Single UTP

(23AWG)

15W

152m

266m

30W 133m

Note: Calculations based on 56VDC starting voltage from power source and accounts for a

10VDC voltage drop. IEEE standards voltage range requirement for powered devices are:

PoE (15W) - 37VDC to 57VDC

PoE+ (30W) - 44VDC to 57VDC.

Altronix Pace1PRMT Installation guide

Brand: Altronix

Model: Pace1PRMT

Category: AV extenders

Type: Installation guide

Download PDF

report

Altronix Pace1PRMT Installation guide

Altronix Pace1PRMT Installation guide

Related papers

Other documents