Amba RSH-B Installation guide

Type
Installation guide

This manual is also suitable for

Page 1
RADIANT SHELF
INSTALLATION INSTRUCTIONS
INCLUDED COMPONENTS TOOLS REQUIRED
Two year limited
warranty with proof of
purchase will apply if all
Terms and Conditions of
Sale are met and
Installation Instructions
are adhered to.
WARRANTY
CONTACT
Email: info@ambaproducts.com
Tel: 4043509738
Fax: 4043550166
www.ambaproducts.com
Plug-In units include
Cord with grounded plug
Follow Steps:
1,3,4
No Wire Connection
or plate required
PLUG-IN INSTALLATION
Requires Grounded Outlet
AVAILABLE MODELS
B-Brushed P-Polished
* Please read the Safety Measures before installing your RADIANT Heated Towel Rack.
* All installations should be in accordance with National and Local electrical codes.
* The Heated Towel Rail should be installed on a GFCI protected circuit and wired by a certified electrician.
* The unit requires a 120 volt, 60Hz power source
* Power plug should be connected to grounded outlet with a minimum rating of 10 amps.
SAFETY MEASURES
• Do not install and connect before reading the installation and operating instructions.
• If you experience any quality problems, DO NOT disassemble but return the unit to the distributor.
• Ensure your hands are dry when unplugging the power cord.
• Unit is intended for indoor use only. Do not place units inside a shower, sauna, steam room, or wherever unit would be exposed to water.
• Ensure that unit is securely fixed to the wall. Under no circumstances should anybody climb or hang on unit.
• Make sure that the electrical circuit breaker is shut off at the main panel before wiring or servicing your unit.
• Never use an extension cord for the Plug-in model.
As this is a heating device, the surface temperature can increase depending on the ambient temperature in the room and the
number of towels applied to the unit. Overloading the unit will cause the unit to become extremely hot and may result in a burn if
touched and/or damage to towels.
For a guide to loading towels refer to our website: ambaproduct.com/towels
OPERATING INSTRUCTION
• After installation, connect the electric power. Remove the protective cover from the switch and turn it to the on position. The
indicator light will glow red and the towel warmer will start to heat.
• This towel warmer has been designed to run continuously. Turn off the switch or unplug the cord when the towel warmer is
not in use for long periods of time.
CLEANING INFORMATION
• Clean the unit with a soft, non-abrasive, damp cloth while warm. Once the towel warmer has cooled, lightly polish with a soft dry cloth.
• Do not use abrasive cleaning powders, metal polish or chlorine based cleaners on any part of the towel warmer.
B
4x
F
1x 1x
H
G
1x
2X
D
M5x15
#6-32 x ¾ -in
A
4x
C
4x
4x
E
ST4. 2x40
m5x8
Page 2
RADIANT SHELF
INSTALLATION INSTRUCTIONS
BEFORE STARTING ASSEMBLY MAKE SURE ALL COMPONENTS LISTED ARE IN THE PACKAGE
DO NOT OVERTIGHTEN SET SCREW
1 2
3
4
5
22 3/8”
568mm
9 13/16”
250mm
E
E
A
B
C
Center of
Wall Plate
6 3/8"
162mm
2B2A
H
F
G
For hardwired installation cut plug from end of
cable and follow wiring guide below
WIRING GUIDE
HOT LOAD
(Black)
GROUND
(Green)
NEUTRAL LOAD
(White)
ELECTRICAL BOX
HEATED
TOWEL
RACK
FROM POWER SOURCE
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
A
A
B
B
C
C
G
D
F
ON/OFF
SWITCH
Turn on unit with switch
  • Page 1 1
  • Page 2 2

Amba RSH-B Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI