Fujitsu 9RLF Service Instructions Manual

Brand: Fujitsu

Model: 9RLF

Category: Split-system air conditioners

Type: Service Instructions Manual

This manual is also suitable for

SPLIT TYPE

ROOM AIR CONDITIONER

WALL MOUNTED

type

Models Indoor unit Outdoor unit

INVERTER

SERVICE

INSTRUCTION

R410A

ASU 9RLF

ASU12RLF

ASU15RLS

AOU 9RLFW

AOU12RLFW

AOU15RLS

CONTENTS

1. DESCRIPTION OF EACH CONTROL OPERATION

1. COOLING OPERATION................................................................................................

3. DRY OPERATION.........................................................................................................

2. HEATING OPERATION.................................................................................................

5. INDOOR FAN CONTROL..............................................................................................

4. AUTO CHANGEOVER OPERATION............................................................................

7. LOUVER CONTROL.....................................................................................................

6. OUTDOOR FAN CONTROL..........................................................................................

9. TIMER OPERATION CONTROL...................................................................................

8. COMPRESSOR CONTROL..........................................................................................

11. TEST OPERATION CONTROL...................................................................................

10. ELECTRONIC EXPANSION VALVE CONTROL........................................................

13. FOUR-WAY VALVE EXTENSION SELECT................................................................

12. PREVENT TO RESTART FOR 3 MINUTES ( 3 MINUTES ST ).................................

15. MANUAL AUTO OPERATION ( Indoor unit body operation ).....................................

14. AUTO RESTART.........................................................................................................

16. FORCED COOLING OPERATION..............................................................................

18.

MINIMUM HEAT OPERATION....................................................................................

17. COMPRESSOR PREHEATING..................................................................................

19. ECONOMY OPERATION............................................................................................

21. OFF DEFROST OPERATION CONTROL...................................................................

20.

DEFROST OPERATION CONTROL...........................................................................

01-01

01-02

01-03

01-04

01-06

01-07

01-08

01-09

01-11

01-12

01-13

01-15

22. VARIOUS PROTECTIONS.......................................................................................... 01-16

01-11

2. TROUBLE SHOOTING

2-1 ERROR DISPLAY.......................................................................................................

2-1-1 WIRED REMOTE CONTROLLER DISPLAY (OPTION)....................................

3. APPENDING DATA

2-1-2 OUTDOOR UNIT DISPLAY................................................................................

2-1-3 INDOOR UNIT DISPLAY....................................................................................

2-2 TROUBLE SHOOTING WITH ERROR CODE............................................................

2-3 TROUBLE SHOOTING WITH NO ERROR CODE.....................................................

02-01

02-02

02-03

3-1 FUNCTION SETTING.................................................................................................

3-1-1 INDOOR UNIT....................................................................................................

3-1-2 Procedures to change the Function Setting for wireless RC..............................

03-01

03-03

3-2 Thermistor Resistance Values.....................................................................................

3-2-1 INDOOR UNIT....................................................................................................

3-2-2 OUTDOOR UNIT................................................................................................

03-05

02-04

02-24

2-4 SERVICE PARTS INFORMATION.............................................................................. 02-29

1 . DESCRIPTION OF EACH

CONTROL OPERATION

R410A

WALL MOUNTED type

INVERTER

( Fig.1 : Limit of Maximum Frequency based on Outdoor Temperature )

1. COOLING OPERATION

1-1 COOLING CAPACITY CONTROL

A sensor (room temperature thermistor) built in the indoor unit body will usually perceive

difference or variation between a set temperature and present room temperature, and

controls the operation frequency of the compressor.

* If the room temperature is 4°F(2°C) higher than a set temperature, the compressor operation

frequency will attain to maximum performance.

minimum

frequency

maximum

frequency

ASU9RLF 22rps 79rps

ASU12RLF 18rps 96rps

ASU15RLS 15rps 80rps

Outside air Outside air

temperature temperature

96.8°F

(36°C)

A zone

93.2°F

(34°C)

89.6°F

(32°C)

B zone

86°F

(30°C)

69.8°F

(21°C)

C zone

66.2°F

(19°C)

D zone

Hi Me Lo Quiet

A zone 79rps 61rps 52rps 37rps

B zone 79rps 61rps 52rps 37rps

C zone 79rps 61rps 52rps 37rps

9RLF

D zone 52rps 43rps 37rps 28rps

E zone 64rps 55rps 49rps 36rps

F zone 64rps 55rps 49rps 36rps

96rps 61rps 51rps 33rps

57rps 42rps 36rps 27rps

A zone

B zone

C zone

12RLF

15RLS

D zone

E zone

F zone

80rps 45rps 37rps 29rps

47rps 37rps 31rps 22rps

A zone

B zone

C zone

D zone

E zone

F zone

( Table1 : Compressor Frequency Range )

01-01

E zone

F zone

50°F

(10°C)

32°F

(0°C)

53.6°F

(12°C)

35.6°F

(2°C)

* When the room temperature is between +4°F(+2°C) to -5°F(-2.5°C) of the setting temperature,

the compressor frequency is controlled within the range shown in Table1.

However, the maximum frequency is limited in the range shown in Figure1 based on the

fan speed mode and the outdoor temperature.

* If the room temperature is 5°F(2.5°C) lower than a set temperature, the compressor will be

stopped.

2. HEATING OPERATION

2-1 HEATING CAPACITY CONTROL

A sensor (room temperature thermistor) built in the indoor unit body will usually perceive

difference or variation between a set temperature and present room temperature, and

controls the operation frequency of the compressor.

* If the room temperature is lower by 6°F(3°C) than a set temperature, the compressor operation

frequency will attain to maximum performance.

* If the room temperature is higher 5°F(2.5°C) than a set temperatire, the compressor will be

stopped.

* When the room temperature is between +5°F(+2.5°C) to -6°F(-3°C) of the setting temperature,

the compressor frequency is controlled within the range shown in Table2.

( Table2 : Compressor Frequency Range )

01-02

minimum

frequency

maximum

frequency

ASU9RLF 22rps 99rps

ASU12RLF 18rps 130rps

ASU15RLS 15rps 119rps

3. DRY OPERATION

3-1 INDOOR UNIT CONTROL

The compressor rotation frequency shall change according to the temperature, set temperature,

and room temperature variation which the room temperature sensor of the indoor unit body has

detected as shown in the Table3.

However, after the compressor is driven, the indoor unit shall run at operation frequency of

64rps (9RLF), 61rps (12RLF), 51rps (15RLS), for a minute.

Ts+1°F

(Ts+0.5°C)

Ts-1°F

(Ts-0.5°C)

Ts-3°F

(Ts-1.5°C)

Ts+3°F

(Ts+1.5°C)

( Table3 : Compressor frequency )

( Fig.2 : Compressor Control based on Room Temperature )

Operating

frequency

37rps

28rps

0rps

9RLF

X zone

J zone

Y zone

Operating

frequency

J zone

Y zone

X zone

33rps

25rps

0rps

12RLF

Operating

frequency

J zone

Y zone

X zone

29rps

18rps

0rps

15RLS

Room Room

temperature temperature

X zone

J zone

Y zone

4. AUTO CHANGEOVER OPERATION

01-03

Operation flow chart

START

Room temp.

>Ts+4°F(2°C)?

COOLING OPERATION

HEATING OPERATION

YES

TS : Setting temperature

<Ts- 4°F(2°C)?

Thermostat remains

in OFF state for 6 minutes or

longer?

System stops

or operation command other than

auto changeover operation?

Thermostat remains

in OFF state for 6 minutes or

longer?

System stops

or operation command other than

auto changeover operation?

YES

When the air conditioner is set to the AUTO mode by remote control, operation starts in the optimum

mode from among the HEATING, COOLING, DRY and MONITORING modes. During operation, the

optimum mode is automatically switched in accordance with temperature changes. The temperature

can be set between 64°F(18°C) and 88°F(30°C) in 2°F(1°C) steps.

5. INDOOR FAN CONTROL

The airflow can be switched in 5 steps such as AUTO, QUIET, LOW, MED, HIGH,

while the indoor fan only runs.

When Fan mode is set at (Auto), it operates on (MED) Fan Speed.

01-04

1. Fan speed

2. FAN OPERATION

( Table4 : Indoor Fan Speed )

Operation mode Air flow mode

Speed (rpm)

1330

1290

1160

980

Cooling/ Fan

710

600

480

1330

Me+

Heating

1160

930

Quiet

680

Dry

S-Lo

X zone: 680

J zone: 660

1500

1360

1230

1050

770

600

480

1440

1230

1000

750

X zone: 750

J zone: 730

Cool air prevention

3. COOLING OPERATION

Switch the airflow [AUTO], and the indoor fan motor will run according to a room temperature,

as shown in Figure3.

On the other hand, if switched in [HIGH] [QUIET], the indoor motor will run at a constant airflow of [COOL]

operation modes QUIET, LOW, MED, HIGH,as shown in Table4.

( Fig.3 : Airflow change - over ( Cooling : AUTO ) )

When the room

temperature rises

When the room

temperature drops

TR : Room temperature

Ts : Setting temperature

TR-Ts > 4°F

(2°C)

2°F > TR-Ts

(1°C)

4°F > TR-Ts > 2°F

(2°C) (1°C)

TR-Ts > 5°F

(2.5°C)

3°F > TR-Ts

(1.5°C)

5°F > TR-Ts > 3°F

(2.5°C) (1.5°C)

HIGH mode

MED mode

LOW mode

ASU9RLF ASU12RLF ASU15RLS

4. DRY OPERATION

Refer to th

ble4.

During the d

ry mode operation, the fan speed sett

ing c

an not be

hange

The maximum value of the indoor fan speed is set as shown in Figure5, based on the detected

temperature by the indoor heat exchanger sensor on heating mode.

(Fig.5 : Cool Air Prevention Control)

01-05

5. HEATING OPERATION

Switch the airflow [AUTO], and the indoor fan motor will run according to a room temperature,

as shown in Figure4.

Switch the airflow [AUTO] at cooling mode, and the indoor fan motor will run as shown in Figure6.

On the other hand, if switched in [HIGH] [QUIET], the indoor motor will run at a constant airflow

of [HEAT] operation modes QUIET, LOW, MED, HIGH, as shown in Table4.

6. COOL AIR PREVENTION CONTROL (Heating mode)

7. MOISTURE RETURN PREVENTION CONTROL (Cooling mode& Dry mode)

( Fig.4 : Airflow change - over ( Heating : AUTO ) )

TR-Ts > -3°F

(-1.5°C)

-5°F > TR-Ts

(-2.5°C)

-3°F > TR-Ts > -5°F

(-1.5°C) (-2.5°C)

TR-Ts > -2°F

(-1°C)

-4°F > TR-Ts

(-2°C)

-2°F > TR-Ts > -4°F

(-1°C) (-2°C)

When the room

temperature rises

When the room

temperature drops

TR : Room temperature

Ts : Setting temperature

LOW mode

MED mode

MED+ mode

107.6°F (42°C)

86°F (30°C)

93.2°F (34°C)

Indoor heat exchanger

temperature

Indoor heat exchanger

temperature

Me+

Cool air

prevention

102.2°F (39°C)

98.6°F (37°C)

89.6°F (32°C)

75.2°F (24°C)

S-Lo

( Fig.6 : Indoor Fan Control )

Compressor

OFF

Indoor fan

Setting air flow

Indoor fan

(as shown in Table 5)

S-Lo

OFF

10 30 60 180 60 180 60 10 30

(SEC)

( Table5 : Indoor fan speed )

X zone J zone

ASU9/ 12RLF 680rpm 660rpm

ASU15RLS 750rpm 730rpm

Y zone

0 480rpm

480rpm

Dry

Cooling

6. OUTDOOR FAN CONTROL

( Table7 : Outdoor fan speed )

The outdoor fan speed mentioned above depends on the compressor frequency.

(When the compressor frequency increases, the outdoor fan speed also changes to the higher

speed. When the compressor frequency decreases, the outdoor fan speed also changes to the

lower speed.)

After the defrost control is operated on the heating mode, the fan speed keeps at the higher speed

as table8 without relating to the compressor frequency.

01-06

( Table8 : Outdoor fan speed after the defrost )

1. Outdoor Fan Motor

2. Fan Speed

AC Motor DC Motor

ASU9/ 12RLF,15RLS

Following table shows the type of the outdoor fan motor. The control method is different

between AC motor and DC motor.

( Table6 : Type of Motor )

ASU9RLF 900rpm

Cooling Heating

ASU9RLF

ASU12RLF

ASU15RLS

Zone

860/ 780/ 760/ 470

900/ 760/ 720/ 680/ 470

950/ 850/ 750/ 680/ 550/ 450

1100/ 850/ 780/ 590/ 480

Refer to Fig.7

(rpm)

860/ 470/ 330

230

150

850/ 750/ 670/ 500

850/ 500/ 350

330

230

1050/ 1010/ 870/ 720/ 530

Dry

760/ 470

530

870/ 530/ 300

300/ 250

250/ 200

ASU12RLF 950rpm

ASU15RLS 1100rpm

( Fig.7 : Outside air temperature zone selection )

69.8°F (21°C)

50°F (10°C)

Outside air

temperature

Outside air

temperature

Z zone

Y zone

F zone

G zone

53.6°F (12°C)

35.6°F ( 2°C)

66.2°F (19°C)

32°F ( 0°C)

7. LOUVER CONTROL

1. VERTICAL LOUVER CONTROL

2. SWING OPERATION

Each time the button is pressed, the air direction range will change as follow:

(Function Range)

01-07

The vertical airflow direction is set automatically as shown, in accordance with the type of operation selected.

Cooling / Dry mode

Horizontal flow

Heating mode Downward flow

When the swing signal is received from the remote controller, the vertical louver starts to swing.

(Table9 : Swinging Range)

Air Direction RangeFig.8 :

Cooling / Dry mode

Fan mode ( )

Types of Air flow Direction Setting:

,,,,, :DuringHeating/Cooling/Drymodes

The Remote Controller's display does not change.

Use the air direction adjustments within the ranges shown above.

During AUTO mode operation, for the first a few minutes after beginning operation,

air-flow will be horizontal 1; the air direction cannot be adjusted during this period.

The air flow direction setting will temporarily become 1 when the temperature of the air -flow is

low at the start of the Heating mode.

Range

Heating mode

Fan mode ( )

The SWING operation may stop temporarily when the air conditioner’s fan is not operating,

or when operating at very low speeds.

8. COMPRESSOR CONTROL

1. OPEARTION FREQUENCY RANGE

The operation frequency of the compressor is different based on the operation mode as

shown in the table10.

Cooling Heating

Min Max Min Max Min Max

Dry

ASU9RLF

ASU12RLF

22rps 79rps 22rps 99rps 28rps 37rps

18rps 96rps 18rps 130rps 25rps 33rps

ASU15RLS 15rps 80rps 15rps 119rps 18rps 29rps

ASU9RLF

70rps 82rps 92rps 96rps 96rps 96rps

ASU12RLF

56rps 74rps 87rps 97rps 108rps 119rps

ASU15RLS

40rps 57rps 72rps 80rps 101rps 110rps

80sec 140sec 200sec 380sec 440sec 440sec

(Table10 : Compressor Operation Frequency Range)

2. OPEARTION FREQUENCY CONTROL AT START UP

The compressor frequency soon after the start-up is controlled as shown in the Figure9.

(Fig.9 : Compressor Control at Start-up)

Time

Time Time Time

Time

(Frequency)

(Time)

Frequency

Frequency Frequency

Frequency

Time Time

Time Time Time Time

Frequency

01-08

ASU9RLF

80sec 140sec 200sec 380sec 440sec 500sec

ASU12RLF

80sec 110sec 140sec 200sec 350sec 410sec

ASU15RLS

9. TIMER OPEARTION CONTROL

1. OPEARTION FREQUENCY RANGE

The table11 shows the available timer setting based on the product model.

ON TIMER / OFF TIMER PROGRAM TIMER SLEEP TIMER

ASU9/ 12RLF,15RLS

OFF timer : When the clock reaches the set time, the air conditioner will be turned off.

Operation mode

Stop mode

Set time of timer

ON timer : When the clock reaches the set time, the air conditioner will be turned on.

Operation mode

Stop mode

Set time of timer

The program timer allows the OFF timer and ON timer to be used in combination one time.

Operation mode

Operation will start from the timer setting (either OFF timer or ON timer) whichever is closest

to the clock's current timer setting.

The order of operations is indicated by the arrow in the remote control unit's display.

SLEEP timer operation cannot be combined with ON timer operation.

(Table11 : Timer Setting)

2. PROGRAM TIMER

Stop mode

Operation mode

Set time

Set time Set time Set time

01-09

3. SLEEP TIMER

If the sleep is set, the room temperature is monitored and the operation is stopped automatically.

If the operation mode or the set temperature is change after the sleep timer is set, the operation is

continued according to the changed setting of the sleep timer from that time ON.

Set temperature rises

( Ts : Set temperature )

Stop of operation

Set temperature lowers

( Ts : Set temperature )

Stop of operation

In the cooling operation mode

When the sleep timer is set, the setting temperature is increased 2°F(1°C).

It increases the setting temperature another 2°F(1°C) after 1 hour.

After that, the setting temperature is not changed and the operation is stopped at the time

of timer setting.

+2°F (1°C)

+4°F (2°C)

Set

60min

In the heating operation mode

When the sleep timer is set, the setting temperature is decreased 2°F(1°C).

It decreases the setting temperature another 2°F(1°C) every 30 minutes.

Upon lowering 8°F(4°C) the setting temperature is not changed and the operation stops at

the time of timer setting.

-8°F (-4°C)

-6°F (-3°C)

-4°F (-2°C)

-2°F (-1°C)

Set

30min

01-10

10. ELECTRONIC EXPANSION VALVE CONTROL

The most proper opening of the electronic expansion valve is calculated and controlled under the

present operating condition based on the Table12.

The compressor frequency, the temperatures detected by the discharge temperature sensor, the

indoor heat exchanger sensor, the outdoor heat exchanger sensor,

and the outdoor temperature sensor.

The expansion valve is set at 480 pulses after 110 seconds of stopping compressor.

At the time of supplying the power to the outdoor unit, the initialization of the electronic

expansion valve is operated (528 pulses are input to the closing direction).

11. TEST OPERATION CONTROL

Under the condition where the air conditioner runs, press the test run button of the remote

control, and the test operation control mode will appear. During test running, the operation lamp

and timer lamp of the air conditioner body twinkle simultaneously. Set the test operation mode,

and the compressor will continue to run regardless of whether the room temperature sensor detects.

The test operation mode is released if 60 minutes have passed after setting up the test operation.

The compressor won't enter operation status for 2 minutes and 20 seconds after the compressor is

stopped, even if any operation is given.

At the time when the air conditioner is switched from the cooling mode to heating mode, the

compressor is stopped, and the four-way valve is switched in 2 minutes and 20 seconds later after

the compressor stopped.

When the power was interrupted by a power failure, etc. during operation, the operation contents

at that time are memorized and when power is recovered, operation is automatically started with

the memorized operation contents.

When the power is interrupted and recovered during timer operation, since the timer operation time

is shifted by the time the power was interrupted, an alarm is given by blinking (7 sec ON/2 sec OFF)

the indoor unit body timer lamp.

[Operation contents memorized when the power is interrupted]

Operation mode

Set temperature

Set air flow

Timer mode and timer time

Set air flow Direction

Swing

ECONOMY operation

MINIMUM HEAT operation

12. PREVENT TO RESTART FOR 3 MINUTES ( 3 MINUTES ST )

13. FOUR-WAY VALVE EXTENSION SELECT

14. AUTO RESTART

01-11

Cooling / Dry mode

Heating mode

Cooling / Dry mode

Heating mode

ASU9/ 12RLF

ASU15RLS

Operation mode Pulse range

between 60 to 480 pulses.

between 45 to 480 pulses.

Table12 : The pulse range of the electronic expansion valve control

15. MANUAL AUTO OPERATION (Indoor unit body operation)

If MANUAL AUTO Button is set, the operation is controlled as shown in Table13.

If the remote control is lost or battery power dissipated, this function will work without the remote control.

OPERATION MODE Auto changeover

FAN CONT. MODE Auto

TIMER MODE Continuous

SETTING TEMP. 75.2°F (24°C)

SETTING LOUVER Standard

SWING

ECONOMY

OFF

When the outdoor temperature is lower than 68°F(20°C) and the heating operation has been

stopped for 30 minutes, power is applied to the compressor and the compressor is heated.

(By heating the compressor, warm air is quickly discharged when operation is started.)

When operation was started and when the outdoor temperature rises to 77°F(25°C) or greater,

preheating is ended.

(Table13)

(No timer setting available)

17. COMPRESSOR PREHEATING

01-12

Forced cooling operation

Cooling

16. FORCED COOLING OPERATION

Forced cooling operation is started when pressing MANUAL AUTO button for 10 seconds or more.

During the forced cooling operation, it operates regardless of room temperature sensor.

Operation LED and timer LED blink during the forced cooling operation. They blink for 1 second ON

and 1 second OFF on both operation LED and timer LED (same as test operation).

Forced cooling operation is released after 60 minutes of starting operation.

The FORCED COOLING OPERATION will start as shown in Table13.

Horizontal

OFF

Room Temp is not controlled

Manual auto operation

18. MINIMUM HEAT OPERATION

The MINIMUM HEAT operation functions by pressing MIN.HEAT button on the remote controller.

The MINIMUM HEAT operation is almost the same operation as below settings.

Mode Heating

Setting temperature 50°F (10°C)

Fan mode AUTO

( Table14 )

19. ECONOMY OPERATION

The ECONOMY operation functions by pressing ECONOMY button on the remote controller.

The ECONOMY operation is almost the same operation as below settings.

Mode Cooling/ Dry Heating

Target temperature Setting temp.+2°F Setting temp.-2°F

(+1°C) (-1°C)

( Table15 )

20. DEFROST OPERATION CONTROL

01-13

1. CONDITION OF STARTING THE DEFROST OPERATION

The defrost operation starts as shown in the following Table 16.

2. CONDITION OF THE DEFROST OPERATION COMPLETION

Release Condition

Outdoor heat exchanger temperature sensor value is higher than

+60.8°F (+16°C) or Compressor operation time has passed 15 minutes.

(Table 16 : Condition of starting Defrost Operation)

Defrost operation is released when the conditions become as shown in Table 17.

(Table 17 : Defrost Release Condition)

Integrating defrost

If the compressor continuous operation time is less than 10 minutes,

the OFF number of the compressor is counted.

If any defrost operated, the compressor OFF count is cleared.

Normal defrost

Compressor integrating operation time

Less than 25 minutes More than 25 minutes

Does not operate

Outdoor heat exchanger temp. < 1.4°F (-17°C)

(at outside air temp. > 14°F (-10°C))

Outdoor heat exchanger temp. < Outside air temp.- 12.6°F (7°C)

or Outdoor heat exchanger temp. < - 4°F (-20°C)

(at outside air temp. < 14°F (-10°C))

More than 240 minutes

(For continuous operation)

Less than 10 minutes

( For

intermittent operation )

Compressor integrating operation time

Outdoor heat exchanger temp.

below 26.6°F (-3°C)

OFF count of the compressor

40 times

01-14

Outdoor fan : OFF

Compressor speed:0rps

EEV : 480pulse

4-way valve : OFF

Compressor speed : 90rps (09/ 12)

70rps (15)

3. Defrost Flow Chart

The defrosting shall proceed by the integrating operation time, outdoor temperature

and outdoor heat exchanger temperature as follows.

(Not defrosted for 10 minutes)

Heating operation start : Compressor ON

Outdoor HEX temp.: Over 60.8°F(16°C)

Compressor ON time: Maximum 15 minutes

Defrost end

Outdoor HEX temp.

Below 1.4°F

(-17°C)

Outdoor HEX temp.

- Outside air temp.

Below - 12.6°F(7°C)

Outdoor HEX temp.

Below - 4°F(-20°C)

Compressor

integrating

operation:

Over 240 minutes

Integrating defrost

Defrost Indicator:

[Operation lamp]

7 sec ON / 2 sec OFF

Defrost start

Outdoor HEX temp.

Below 26.6°F(-3°C)

Compressor

OFF count :

40 times

Normal defrost

Outside air temp. > 14°F

(-10°C)

Outside air temp. < 14°F

(-10°C)

Intermittent operation Continuous operation

21. OFF DEFROST OPEARTION CONTROL

1. OFF DEFROST OPERATION CONDITION

When operation stops in the [Heating operation] mode, if frost is adhered to the outdoor unit heat

exchanger, the defrost operation will proceed automatically. In this time, if indoor unit defrost lamp

lighting, the outdoor unit will allow the heat exchanger to defrost, and then stop.

In heating operation, the outdoor heat exchanger temperature is less than 24.8°F (-4°C), and

compressor operation integrating time lasts for more than 30 minutes.

OFF Defrost Flow Chart

Heating operation stop

Outdoor heat exchanger temperature:

Below 24.8°F(-4°C)

and

Compressor integrating operation:

Over 30 minutes

Defrost start

Defrost Indicater:

[Defrost lamp]

Lighting

Outdoor heat exchanger temperature:

Over 60.8°F (16°C) or

Compressor ON time: Over 15 minutes

Defrost end

2. OFF DEFROST END CONDITION

Release Condition

Outdoor heat exchanger temperature sensor value is higher than 60.8°F (16°C)

or Compressor operation time has passed 15 minutes.

01-15

22. VARIOUS PROTECTIONS

1. DISCHARGE GAS TEMPERATURE OVERRISE PREVENSION CONTROL

The discharge gas thermosensor (discharge thermistor : Outdoor side) will detect discharge gas

temperature.

ASU9/ 12RLF,15RLS

219.2°F

(104°C)

213.8°F

(101°C)

230°F

(110°C)

When the discharge temperature becomes higher than Temperature ,the compressor frequency

is decreased 20rps, and it continues to decrease the frequency for 20rps every 120 seconds until

the temperature becomes lower than Temperature .

When the discharge temperature becomes lower than Temperature , the control of the control of

the compressor frequency is released.

When the discharge temperature becomes higher than Temperature ,the compressor is stopped

and the indoor unit LED starts blinking.

(Table18 : Discharge Temperature Over Rise Prevension Control / Release Temperature)

Temperature

2. CURRENT RELEASE CONTROL

The compressor frequency is controlled so that the outdoor unit input current does not exceeds

the current limit velue that was set up with the outdoor temperature.

The compressor frequency returns to the designated frequency of the indoor unit at the time

when the frequency becomes lower than the release value.

(Table19 : Current Release Operation Value / Release Value)

01-16

[ Heating ]

OT (Control / Release)

5.5A/ 5.0A

6.0A/ 5.5A

7.0A/ 6.5A

5.5A/ 5.0A

7.0A/ 6.5A

7.5A/ 7.0A

8.5A/ 8.0A

62.6°F(17°C)

53.6°F(12°C)

OT : Outdoor Temperature

41°F(5°C)

62.6°F(17°C)

53.6°F(12°C)

41°F(5°C)

62.6°F(17°C)

53.6°F(12°C)

41°F(5°C)

ASU9RLF

OT (Control / Release)

OT : Outdoor Temperature

ASU12RLF

OT (Control / Release)

3.5A/ 3.0A

4.0A/ 3.5A

5.5A/ 5.0A

4.0A/ 3.5A

5.0A/ 4.5A

6.0A/ 5.5A

114.8°F(46°C)

104°F(40°C)

114.8°F(46°C)

104°F(40°C)

114.8°F(46°C)

104°F(40°C)

OT : Outdoor Temperature

ASU9RLF

OT (Control / Release)

OT : Outdoor Temperature

ASU12RLF

[ Cooling ]

7.0A/ 6.5A

9.0A/ 8.5A

10.0A/ 9.0A

10.0A/ 9.5A

OT (Control / Release)

OT : Outdoor Temperature

ASU15RLS

4.5A/ 3.0A

6.0A/ 5.5A

8.5A/ 8.0A

OT (Control / Release)

OT : Outdoor Temperature

ASU15RLS

3. ANTIFREEZING CONTROL (Cooling and Dry mode)

The compressor frequency is decrease on cooling & dry mode when the indoor heat exchanger

temperature sensor detects the temperature lower than Temperature .

Then, the anti-freezing control is released when it becomes higher than Temperature .

(Table19 : Anti-freezing Protection Operation / Release Temperature)

4. COOLING PRESSURE OVERRISE PROTECTION

When the outdoor unit heat exchange sensor temperature rises to 152.6°F (67°C) or greater,

the compressor and the outdoor fan motor are stopped and trouble display is performed.

5. HIGH TEMPERATURE RELEASE CONTROL ( HEATING MODE )

On heating mode, the compressor frequency is controlled as following based on the

detection value of the indoor heat exchanger temperature sensor.

01-17

Indoor heat exchange

temperature

[ Control System ]

It returns to the normal operation

127.4°F

(53°C)

122°F

(50°C)

Outdoor temperature

Over than 50°F(10°C) *1

or 53.6°F(12°C) *2

Less than 50°F(10°C) *1

or 53.6°F(12°C) *2

*1. When the temperature rises.

*2. When the temperature drops.

39.2°F (4°C)

44.6°F (7°C)

55.4°F (13°C)

Temperature Temperature

The compressor frequency is

decreased 3rps every 60seconds.

Page is loading ...

Fujitsu 9RLF Service Instructions Manual

Brand: Fujitsu

Model: 9RLF

Category: Split-system air conditioners

Type: Service Instructions Manual

This manual is also suitable for

Download PDF

report

Fujitsu 9RLF Service Instructions Manual

This manual is also suitable for

Fujitsu 9RLF Service Instructions Manual

Related papers

Other documents