ESAB Mig C240s PRO User manual

Brand: ESAB

Model: Mig C240s PRO

Category: Welding System

Type: User manual

This manual is also suitable for

ESAB Mig C240s PRO is an advanced welding power source designed for professional welding applications. It offers precise control over the welding process, enabling you to achieve high-quality welds on a wide range of materials, including steel, stainless steel, and aluminum. With its user-friendly interface and robust construction, the Mig C240s PRO is an excellent choice for both experienced welders and those new to the craft.

Key features of the Mig C240s PRO include:

Excellent weld quality: The C240s PRO delivers a stable arc and precise wire feed, resulting in consistent, high-quality welds.

Key features of the Mig C240s PRO include:

Excellent weld quality: The C240s PRO delivers a stable arc and precise wire feed, resulting in consistent, high-quality welds.

Valid for serial no. 6270349 301 115 061026

Mig C240 PRO

Mig C240s PRO

Origo







Instruction manual

ENGLISH

-- 2 --

TOCe

1 DIRECTIVE 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2 SAFETY 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3 INTRODUCTION 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 Equipment 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4 TECHNICAL DATA 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5 INSTALLATION 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 Placing 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 Assembly of components 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 Electrical installation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 Mains power supply 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 OPERATION 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 Connection and control devices 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 Welding without gas 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 Wire feed pressure 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4 Replacing and inserting wire 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.5 Overheating protection 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.6 Inductance connection 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.7 OrigoTM Mig C240 PRO 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.8 OrigoTM Mig C240s PRO 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7 MAINTENANCE 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1 Inspection and cleaning 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8 FAULT TRACING 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9 ORDERING OF SPARE PARTS 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DIAGRAM 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ACCESSORIES 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

-- 3 --

C240Pe

1 DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that weld-

ing power source Origo

Mig C240 PRO, Origo

Mig C240s PRO from serial number 627 complies

with standard IEC/EN 60974--1, in accordance with the requirements of directive (73/23/EEC) and

addendum (93/68/EEC) and with standard IEC/EN 60974--10 in accordance with the requirements of

directive (89/336/EEC) and addendum (93/68/EEC).

--------------------------------------------------------------------------------------------------------------------------------------

Kent Eimbrodt

Global Director Equipment and Automation

ESAB AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

Laxå 2006--09--05

2 SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

S its operation

S location of emergency stops

S its function

S relevant safety precautions

S welding

2. The operator must ensure that:

S no unauthorised person is stationed within the working area of the equipment when it is

started up.

S no--one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose

S be free from draughts

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.

S Work on high voltage equipment may only be carried out by a qualified electrician.

S Appropriate fire extinquishing equipment must be clearly marked and close at hand.

S Lubrication and maintenance must not be carried out on the equipment during operation.

-- 4 --

C240Pe

WARNING!

Read and understand the instruction manual

before installing or operating.

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.

S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

S Insulate yourself from earth and the workpiece.

S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.

S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.

S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

Do not use the power source for thawing frozen pipes.

WARNING!

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

-- 5 --

C240Pe

3 INTRODUCTION

Origo

Mig C240 PRO & Origo

Mig C240s PRO are step controlled power sources in a compact

design, intended for welding with solid steel, stainless steel or aluminium wire as well as tubular wire

with or without shielding gas.

The possibility of welding with homogeneous wire/shielding gas and welding with gasless tubular wire

is obtained by switching the + and -- connections on the switching terminal above the wire feed unit.

ESAB’s accessories for the product can be found on page 20.

3.1 Equipment

The power source is supplied with:

S Welding gun PSF 250 -- 3m

S Return cable 3,5m with return clamp

S Shelf for gas cylinder

S Instruction manual

4 TECHNICAL DATA

Origo

Mig C240 PRO Origo

Mig C240s PRO

Voltage 230/400--415V, 3∼ 50/60Hz 230/400--415V, 3∼ 50/60Hz

Permissible load at

100% duty cycle 130A 130A

60 % duty cycle 170A 170A

30 % duty cycle 240A 240A

Setting range (DC) 20A /15V--240A / 23,0V 20A /15V--240A / 23,0V

Open circuit voltage 14 -- 32V 14 -- 32V

Open circuit power 190W 190W

Efficiency 76% 76%

Power factor 0.95 0.95

Control voltage 42 V, 50/60Hz 42 V, 50/60Hz

Wire feed speed 1,9 -- 19m/min 1,4 -- 19m/min

Burnback time 0 -- 0,25s 0 -- 0,25s

Spot welding 0,2 -- 2,5s 0,2 -- 2,5s

Creep start -- + (auto)

2/4 stroke & motor inching -- +

Welding gun connection EURO EURO

Wire dimension range 0,6 -- 1,0mm 0,6 -- 1,0mm

Max diameter of wire bobin 300mm 300mm

Dimensions lxwxh 840x425x830 840x425x830

Weight 103 kg 100 kg

Operating temperature --10 ÷ +40

C --10 ÷ +40

Enclosure class IP 23 IP 23

Application classification

-- 6 --

C240Pe

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-

tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio

interference. It is the user’s responsibility to take adequate precautions.

5.1 Placing

Position the welding power source such way that its cooling air inlets and outlets are

not obstructed.

5.2 Assembly of components

-- 7 --

C240Pe

During transport, the rear wheels of the power source are in their forward position.

Before use, place the wheels in their rear position.

WARNING!

5.3 Electrical installation

5.4 Mains power supply

Check that the unit is connected to the correct mains power supply voltage, and that

it is protected by the correct fuse size. A protective earth connection must be made,

in accordance with regulations.

Rating plate with supply connection data

Origo

Mig C240 PRO

Origo

Mig C240s PRO

3∼ 50/60 Hz 3∼ 50/60 Hz

Voltage V 230 400/415

Current A

at 100% duty cycle 8.6 5.3

at 60% duty cycle 12.4 7.6

at 30% duty cycle 21 12

Cable area mm

4 x 2.5 4 x 1.5

Fuse slow A 20 16

NB: The mains cable areas and fuse sizes as shown above are in accordance with Swedish

regulations. They may not be applicable in other countries: make sure that the cable area and fuse

sizes comply with the relevant national regulations.

-- 8 --

C240Pe

6 OPERATION

General safety regulations for the handling of the equipment can be found on

page 3. Read through before you start using the equipment!

WARNING!

Rotating parts can cause injury, take great care.

To prevent the reel sliding off the hub: Lock the reel in place by turning

the red knob as shown on the warning label attached next to the hub.

WARNING!

WARNING -- TIPPING RISK!

There is a risk of tipping while transportation and operation, if the welding machine leans

more than 10

. In that case appropriate securing has to be provided !

6.1 Connection and control devices

Origo

Mig C240 PRO

1 Mains supply switch 7 Connection for return cable (--), high inductance

2 Switch, coarse control 8 Connection for return cable (--), low inductance

3 Switch, precise control 9 Knob for wire speed setting

4 Indicating lamp, power supply ON 10 Knob for spot welding -- ON/OFF and time setting

5 Orange indicating lamp, overhea-

ting

11 Digital instrument -- V / A

(option,see page 20)

6 EURO -- connector for welding gun 12 Knob for burn--back time setting

-- 9 --

C240Pe

Origo

Mig C240s PRO

1 Mains supply switch 11 Digital display for welding parameters

2 Switch, coarse control 12 Switch for display selection -- Volt. or Amp

3 Switch, precise control 13 Switch for display selection -- m/min or mm

4 Indicating lamp, power supply ON 14 Lamp indicating status of synergy control

5 Orange indicating lamp, overheating 15 Lamps indicating recommended (--) current

output -- max/min inductance

6 EURO -- connector (for welding gun) 16 Switch for ”Synergy”-- ON/OFF and ma-

terial/gas selection

7 Connection for return cable (--), high induc-

tance

17 Knob for selection of the wire diameter

8 Connection for return cable (--), low induc-

tance

18 Knob for burn--back time setting

9 Knob for wire speed setting / correction 19

Mode selector 2--stroke / / 4--stroke

10 Knob for spot welding -- ON/OFF and time

setting

-- 10 --

C240Pe

6.2 Welding without gas

6.3 Wire feed pressure

Start by making sure that the wire moves smoothly through the wire guide. Then

set the pressure of the wire feeder’s pressure rollers. It is important that the

pressure is not too great.

Fig 1 Fig 2

To check that the feed pressure is set correctly, you can feed out the wire against

an insolated object, e.g. a piece of wood.

When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed

rollers should slip.

If you hold the gun approx. 50 mm from the piece of wood, the wire should be

fed out and bend (fig. 2).

6.4 Replacing and inserting wire

S Open the side panel.

S Disconnect the pressure sensor by folding it backwards, the pressure rollers

slide up.

-- 11 --

C240Pe

S Straighten out the new wire 10--20 cm. File away burrs and sharp edges from the

end of the wire before inserting it into the wire feed unit.

S Make sure that the wire goes properly into the feed roller track and into the outlet

nozzle and the wire guide.

S Secure the pressure sensor.

S Close the side panel.

6.5 Overheating protection

When the machine is switched on with the mains switch [1], indicating lamp [4] is on and

lamp [5] off -- the machine is ready to operate. If the internal temperature becomes too

high, the welding is interrupted and disabled. This state is indicated by lighting of the

orange indicating lamp [5] on the front of the machine. It resets automatically when the

temperature has fallen.

6.6 Inductance connection

Higher inductance produces a more flowing weld and fewer spatters. Lower inductance

produces a harsher sound and a stable, concentrated arc.

6.7 Origo

Mig C240 PRO

The Origo

Mig C240 PRO is equipped with standard control unit. Welder can

manually select and adjust all welding parameters.

S Wire speed (1,9 -- 19m/min).

S Spot--welding time.

S Burn back time.

The machine C240 can be fitted with a digital instrument that displays current and

voltage. It incorporates a hold function (see page 20).

6.8 Origo

Mig C240s PRO

S the standard control (welder can manually select and adjust all welding

parameters) -- switch “SYNERGY” [16] set to OFF

S the synergy control (partly preprogrammed welding parameters) -- switch

“SYNERGY” [16] set to any material/gas group

The stroke control (2/4 stroke) or motor inching (only wire feed motor is activated)

is selected with switch [19]. Burn back time is adjusted with knob [18]. Spot welding

(turning on and time setting 0,5 -- 4s) is activated with knob [10].

For machines C240s digital instrument is included as standard.

6.8.1 Standard control mode

When standard control mode is selected lamps [14, 15] are off and only a lower row

of digital display [11] shows wire speed reference (selector [13] shall be in position

”m/min”).

Operator selects the required voltage [2, 3] and he may set wire speed within full

range (1,4 -- 19m/min) with knob [9].

-- 12 --

C240Pe

During welding process the upper row of display shows actual welding voltage or

current, depending on selection with switch [12]. When welding process is stopped,

displayed values are ”frozen” (dimmed display).

6.8.2 Synergy control mode

In synergy control mode, the operator first has to preselect material/gas [16] and

wire diameter [17].

While changing the voltage (with the voltage selectors [2,3]) digital instrument [11]

and lamps [14,15] on the front panel show welding parameters.

Synergy status lamp [14] is green (only in synergy mode) when correct welding

parameters are set, or red when incorrect or not allowed welding parameters are set

(then machine operation is disabled!).

Note: Lamp is also red (in all control modes):

S if during welding (gun trigger pressed) -- any voltage selector [2, 3]

is operated, then the operation of the machine is disabled immediately until

the trigger is released,

S when the gun trigger is pressed while turning on the machine with switch [1].

One of the lamps [15] points at recommended current outlet (--) with appropriate

inductance [7,8].

Digital display [11] shows values depending on display selectors [12, 13]

and machine status.

Before welding start: the upper display shows expected values of welding current [A]

or voltage [V] (both only in SYNERGY mode); the lower display shows wire speed

reference [m/min] or recommended maximum thickness [mm] of workpiece.

During welding: upper display shows actual welding voltage or current, the lower

display -- as above.

After welding stop: the upper display shows last memorised (HOLD) values of

voltage or current (dimmed display).

Wire speed is set by program (stored in the microprocessor) and the knob [9] shall

be set to middle position ”0”. If necessary the operator may correct the preset speed

reference with that knob within +/-- 20% of the set value.

-- 13 --

C240Pe

7 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself

attempts any work in the product during the guarantee period in order to rectify any

faults.

7.1 Inspection and cleaning

Check regularly that the power source is free from dirt.

The power source should be regularly blown clean using dry compressed air at reduced

pressure. More frequently in dirty environments.

Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid

this you can use an airfilter.

The airfilter is an accessory. Ordering number can be found on page 20.

Welding gun

S Cleaning and replacement of the welding gun’s wear parts should take place at

regular intervals in order to achieve trouble--free wire feed. Blow the wire guide

clean regularly and clean the contact tip.

The brake hub

The hub is adjusted when delivered, if

readjustment is required, follow the instructions

below. Adjust the brake hub so that wire is slightly

slack when wire feed stops.

S Adjusting the braking torque:

S Turn the red handle to the locked position.

S Insert a screwdriver into the springs in the hub.

Turn the springs clockwise to reduce the braking torque

Turn the springs anticlockwise to increase the braking torque. NB: Turn both

springs through the same amount.

-- 14 --

C240Pe

8 FAULT TRACING

Try these recommended checks and inspections before sending for an authorised service technican.

Type of fault

Actions

No arc S Check that the mains power supply switch is turned on.

S Check that the welding current supply and return cables are

correctly connected.

S Check that correct current value is set.

Welding current is interrupted

during welding

S Check whether the thermal overload trip has operated

(indicated by the orange lamp on the front).

S Check the main power supply fuses.

Thermal overload trips

operate frequently

S Check to see whether the air filters are clogged.

S Make sure that you are not exceeding the rated data for the

power source (i.e. that the unit is not being overloaded).

Poor welding performance S Check that the welding current supply and return cables are

correctly connected.

S Check that the correct current value is set.

S Check that the correct welding wires are being used.

S Check the main power supply fuses.

S Check the wire feed unit -- if proper rolls are applied and

properly set the pressure of the wire feeder’s pressure rollers

9 ORDERING OF SPARE PARTS

Origo

Mig C240 PRO, Origo

Mig C240s PRO is designed and tested in accordance

with the international and European standards IEC/EN 60974--1 and EN 60974--10. It is

the obligation of the service unit which has carried out the service or repair work to

make sure that the product still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of

this publication.

Diagram

-- 15 --

dC240P

Origo

Mig C240 PRO, 230/400--415V

-- 16 --

dC240P

Origo

Mig C240s PRO, 230V

-- 17 --

dC240P

Origo

Mig C240s PRO, 400--415V

Origo

Mig C240 PRO, Origo

Mig C240s PRO

Edition 061026

-- 18 --

oC240P

Valid for serial no. 627--XXX--XXXX

Ordering numbers

0349 304 657 Origo

Mig C240 PRO 400--415V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 3m)

0349 304 658 Origo

Mig C240 PRO 230V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 3m)

0349 304 659 Origo

Mig C240s PRO 400--415V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 3m)

0349 304 660 Origo

Mig C240s PRO 230V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 3m)

0349 305 983 Origo

Mig C240 PRO 400--415V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 4,5m)

0349 305 984 Origo

Mig C240 PRO 230V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 4,5m)

0349 305 985 Origo

Mig C240s PRO 400--415V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 4,5m)

0349 305 986 Origo

Mig C240s PRO 230V 3∼

∼∼

∼50/60Hz (welding gun PSF 250, 4,5m)

Origo

Mig C240 PRO, Origo

Mig C240s PRO

Edition 061026

-- 19 --

wC240P

W. F. Mechanism 0455 890 882

Item Denomination Ordering no. Notes

A Pressure roller 0455 907 001

B Feed roller

0367 556 001

0367 556 002

0367 556 006

0367 556 004

Ø 0.6--0.8mm Fe, Ss, cored wire.

Ø 0.8--1.0mm Fe, Ss, cored wire.

Ø 1.0--1.2mm cored wire.

Ø 1.0--1.2mm Al wire.

C Inlet nozzle 0466 074 001

D Insert tube

0455 894 001

0455 889 001

Plastic, must be used together with item 0455 885 001,

for welding with Al wire.

Steel, must be used together with item 0455 886 001.

E Outlet nozzle

0455 885 001

0455 886 001

Must be used together with item 0455 894 001,

for welding with Al wire.

Must be used together with item 0455 889 001.

The rollers are marked with wire dimension in mm, some are also marked with inch.

Welding with aluminium wires.

In order to weld with aluminium wires, proper rollers, nozzles and liners for aluminium wires MUST be

used. It is recommended to use 3m long welding gun for aluminium wires, equipped with appropriate

wear parts.

Origo

Mig C240 PRO, Origo

Mig C240s PRO

Edition 061026

Accessories

-- 20 --

aC240P

Digital meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 302 598

Transformer kit for CO

heater . . . . . . . . . . . 0349 302 250

Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 302 599

Cable holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0349 303 362

Page is loading ...

ESAB Mig C240s PRO User manual

Brand: ESAB

Model: Mig C240s PRO

Category: Welding System

Type: User manual

This manual is also suitable for

Key features of the Mig C240s PRO include:

Excellent weld quality: The C240s PRO delivers a stable arc and precise wire feed, resulting in consistent, high-quality welds.

Download PDF

report

ESAB Mig C240s PRO User manual

This manual is also suitable for

ESAB Mig C240s PRO User manual

Related papers

Other documents