OPERATING INSTRUCTIONS
10000
1. Power button
2. LED indicator
3. Out 5V/1A
4. Out 5V/2.1A
5. In 5V
Included items:
- 1 HALO Pocket Power 10000
- 1 Retractable USB cable
- 1 30-pin adaptor
- 1 Mini-pin adaptor
- Operating Instructions/Warranty
1
2
3
4
5
Charging the HALO Pocket Power 10000
2
To Turn On/O the HALO Pocket Power 10000
To turn on the HALO charger, press the silver power
button the left side of the unit. The battery level is
indicated by the blue LED light located on the right side
of the charger. To conserve power, the charger shuts
down automatically after 10 seconds when not in use.
Power Indicator/Batter Status
Power status is 75-100% when four blue lights are fully
illuminated.
Power status is 50-75% when three blue lights are fully
illuminated.
Power status is 5-50% when two blue lights are fully
illuminated.
Charge the unit if one blue light is fully illuminated or
blinking.
Note: Charge the unit if any or all of the lights are
blinking.
Using Your HALO Pocket Power 10000
Out 5V/1A USB Port (diagram item #3)
Use this port to charge your smartphone, iPod, digital
camera, GPS and portable gaming device. When
possible, use the original USB charging cable that came
with your personal electronic device.
Note: The charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/1A.
3. Insert the other end of the cable with the proper tip
into your personal electronic device (e.g. smartphone,
digital camera, GPS or portable gaming device).
4. The blue LED lights will not illuminate during the
charging process. Press and release the on/o button
to see the battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
Out 5V/2.1A Port (diagram item #4)
Use this port to charge iPads, iPad minis, e-readers and
tablets. You may use the original USB charging cable
that came with your personal electronic device.
Note: the charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/2.1A.
3. Insert the other end of the cable with the proper tip
into your electronic device (e.g. iPad, iPad mini,
e-reader and tablet).
4. The blue LED lights will not illuminate during the
charging process. Press the on/o button to see the
battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
5V Input Port (diagram item #5)
Use this port to charge the HALO Pocket Power 10000.
1. Insert the micro tip (the smaller of the two tips
provided) into the female end of the retractable cable.
2. Insert the USB end of the cable into your computer
or wall charger.
3. HALO charger is fully charged when four blue LED
lights are fully illuminated.
The HALO Pocket Power 10000 should be charged every
three months if not used regularly.
Storing/Handling/Cleaning the HALO Pocket Power
10000
1. Do not get wet or store in extreme temperature
conditions.
2. Do not disassemble this HALO charger or attempt
to repair it.
3. Use a soft cloth with soap to clean the exterior of
your HALO charger. Do not use liquid detergent or
chemicals of any kind.
4. This HALO charger is intended for use with:
iPhone/iPad/iPod, tablets, e-Readers, smartphones,
digital cameras, portable gaming devices, GPS and
MP3 players.
3
To Turn On/O the HALO Pocket Power 10000
To turn on the HALO charger, press the silver power
button the left side of the unit. The battery level is
indicated by the blue LED light located on the right side
of the charger. To conserve power, the charger shuts
down automatically after 10 seconds when not in use.
Power Indicator/Batter Status
Power status is 75-100% when four blue lights are fully
illuminated.
Power status is 50-75% when three blue lights are fully
illuminated.
Power status is 5-50% when two blue lights are fully
illuminated.
Charge the unit if one blue light is fully illuminated or
blinking.
Note: Charge the unit if any or all of the lights are
blinking.
Using Your HALO Pocket Power 10000
Out 5V/1A USB Port (diagram item #3)
Use this port to charge your smartphone, iPod, digital
camera, GPS and portable gaming device. When
possible, use the original USB charging cable that came
with your personal electronic device.
Note: The charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/1A.
3. Insert the other end of the cable with the proper tip
into your personal electronic device (e.g. smartphone,
digital camera, GPS or portable gaming device).
4. The blue LED lights will not illuminate during the
charging process. Press and release the on/o button
to see the battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
Out 5V/2.1A Port (diagram item #4)
Use this port to charge iPads, iPad minis, e-readers and
tablets. You may use the original USB charging cable
that came with your personal electronic device.
Note: the charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/2.1A.
3. Insert the other end of the cable with the proper tip
into your electronic device (e.g. iPad, iPad mini,
e-reader and tablet).
4. The blue LED lights will not illuminate during the
charging process. Press the on/o button to see the
battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
5V Input Port (diagram item #5)
Use this port to charge the HALO Pocket Power 10000.
1. Insert the micro tip (the smaller of the two tips
provided) into the female end of the retractable cable.
2. Insert the USB end of the cable into your computer
or wall charger.
3. HALO charger is fully charged when four blue LED
lights are fully illuminated.
The HALO Pocket Power 10000 should be charged every
three months if not used regularly.
Storing/Handling/Cleaning the HALO Pocket Power
10000
1. Do not get wet or store in extreme temperature
conditions.
2. Do not disassemble this HALO charger or attempt
to repair it.
3. Use a soft cloth with soap to clean the exterior of
your HALO charger. Do not use liquid detergent or
chemicals of any kind.
4. This HALO charger is intended for use with:
iPhone/iPad/iPod, tablets, e-Readers, smartphones,
digital cameras, portable gaming devices, GPS and
MP3 players.
4
To Turn On/O the HALO Pocket Power 10000
To turn on the HALO charger, press the silver power
button the left side of the unit. The battery level is
indicated by the blue LED light located on the right side
of the charger. To conserve power, the charger shuts
down automatically after 10 seconds when not in use.
Power Indicator/Batter Status
Power status is 75-100% when four blue lights are fully
illuminated.
Power status is 50-75% when three blue lights are fully
illuminated.
Power status is 5-50% when two blue lights are fully
illuminated.
Charge the unit if one blue light is fully illuminated or
blinking.
Note: Charge the unit if any or all of the lights are
blinking.
Using Your HALO Pocket Power 10000
Out 5V/1A USB Port (diagram item #3)
Use this port to charge your smartphone, iPod, digital
camera, GPS and portable gaming device. When
possible, use the original USB charging cable that came
with your personal electronic device.
Note: The charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/1A.
3. Insert the other end of the cable with the proper tip
into your personal electronic device (e.g. smartphone,
digital camera, GPS or portable gaming device).
4. The blue LED lights will not illuminate during the
charging process. Press and release the on/o button
to see the battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
Out 5V/2.1A Port (diagram item #4)
Use this port to charge iPads, iPad minis, e-readers and
tablets. You may use the original USB charging cable
that came with your personal electronic device.
Note: the charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/2.1A.
3. Insert the other end of the cable with the proper tip
into your electronic device (e.g. iPad, iPad mini,
e-reader and tablet).
4. The blue LED lights will not illuminate during the
charging process. Press the on/o button to see the
battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
5V Input Port (diagram item #5)
Use this port to charge the HALO Pocket Power 10000.
1. Insert the micro tip (the smaller of the two tips
provided) into the female end of the retractable cable.
2. Insert the USB end of the cable into your computer
or wall charger.
3. HALO charger is fully charged when four blue LED
lights are fully illuminated.
The HALO Pocket Power 10000 should be charged every
three months if not used regularly.
Storing/Handling/Cleaning the HALO Pocket Power
10000
1. Do not get wet or store in extreme temperature
conditions.
2. Do not disassemble this HALO charger or attempt
to repair it.
3. Use a soft cloth with soap to clean the exterior of
your HALO charger. Do not use liquid detergent or
chemicals of any kind.
4. This HALO charger is intended for use with:
iPhone/iPad/iPod, tablets, e-Readers, smartphones,
digital cameras, portable gaming devices, GPS and
MP3 players.
5
To Turn On/O the HALO Pocket Power 10000
To turn on the HALO charger, press the silver power
button the left side of the unit. The battery level is
indicated by the blue LED light located on the right side
of the charger. To conserve power, the charger shuts
down automatically after 10 seconds when not in use.
Power Indicator/Batter Status
Power status is 75-100% when four blue lights are fully
illuminated.
Power status is 50-75% when three blue lights are fully
illuminated.
Power status is 5-50% when two blue lights are fully
illuminated.
Charge the unit if one blue light is fully illuminated or
blinking.
Note: Charge the unit if any or all of the lights are
blinking.
Using Your HALO Pocket Power 10000
Out 5V/1A USB Port (diagram item #3)
Use this port to charge your smartphone, iPod, digital
camera, GPS and portable gaming device. When
possible, use the original USB charging cable that came
with your personal electronic device.
Note: The charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/1A.
3. Insert the other end of the cable with the proper tip
into your personal electronic device (e.g. smartphone,
digital camera, GPS or portable gaming device).
4. The blue LED lights will not illuminate during the
charging process. Press and release the on/o button
to see the battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
Out 5V/2.1A Port (diagram item #4)
Use this port to charge iPads, iPad minis, e-readers and
tablets. You may use the original USB charging cable
that came with your personal electronic device.
Note: the charging cable and tips provided allow you
to charge two devices at the same time.
1. Once fully charged, press and hold the power button
on the HALO charger.
2. Insert the USB end of the supplied cable, or the cable
that came with your personal electronic device, into
the port labeled Out 5V/2.1A.
3. Insert the other end of the cable with the proper tip
into your electronic device (e.g. iPad, iPad mini,
e-reader and tablet).
4. The blue LED lights will not illuminate during the
charging process. Press the on/o button to see the
battery level of the HALO charger.
5. When your personal electronic device is fully
charged, remove the cable from the HALO charger.
5V Input Port (diagram item #5)
Use this port to charge the HALO Pocket Power 10000.
1. Insert the micro tip (the smaller of the two tips
provided) into the female end of the retractable cable.
2. Insert the USB end of the cable into your computer
or wall charger.
3. HALO charger is fully charged when four blue LED
lights are fully illuminated.
The HALO Pocket Power 10000 should be charged every
three months if not used regularly.
Storing/Handling/Cleaning the HALO Pocket Power
10000
1. Do not get wet or store in extreme temperature
conditions.
2. Do not disassemble this HALO charger or attempt
to repair it.
3. Use a soft cloth with soap to clean the exterior of
your HALO charger. Do not use liquid detergent or
chemicals of any kind.
4. This HALO charger is intended for use with:
iPhone/iPad/iPod, tablets, e-Readers, smartphones,
digital cameras, portable gaming devices, GPS and
MP3 players.
6
Safety Precautions
This HALO charger has been designed and manufac-
tured to ensure personal safety. Please read the
following carefully before using. Incorrect operation or
incompatibility with your personal electronic device
may result in reduced battery performance or damage.
- Carefully read the operating instructions, and use the
HALO charger correctly.
- Caution: The lithium-ion rechargeable battery used in
this charging device may present a risk of re or
chemical burn if mistreated. Do not disassemble,
expose to heat above 212°F (100°C) or incinerate.
- Misusing or incorrectly connecting the HALO charger
may cause electric shock to users and damage
equipment. The HALO charger may become warm
under extended high power operation. During
operation, keep the HALO charger away from materials
that may be aected by these temperatures.
- When used correctly, lithium-ion rechargeable
batteries provide a safe and dependable source of
portable power. However, if they are misused or
abused, this may result in leakage, burns, re or
explosion, causing personal injury or damage to other
devices.
- Do not disassemble the HALO charger. There are no
user-serviceable parts inside. Incorrect reassembly
may result in shock or re hazard.
- Do not drop or subject to strong impacts. Do not
operate the HALO charger if it has received a sharp
blow, or otherwise been damaged in any way.
- Do not expose the HALO charger to moisture, water,
rain, or snow.
- Do not insert any object into the ports or openings of
the HALO charger.
- Never charge the HALO charger unattended.
- There is a risk of the batteries exploding, overheating,
or igniting. Do not disassemble, modify, heat or
short-circuit the batteries. Do not place in re or leave
in hot places. Do not expose to direct sunlight.
- Only charge the HALO charger by the specied
method with the specied USB cable.
- In the unlikely event of leakage or explosion use sand
or a chemical re extinguisher.
- Batteries must be recycled or disposed of properly.
7
This HALO charger has been designed and manufac-
tured to ensure personal safety. Please read the
following carefully before using. Incorrect operation or
incompatibility with your personal electronic device
may result in reduced battery performance or damage.
- Carefully read the operating instructions, and use the
HALO charger correctly.
- Caution: The lithium-ion rechargeable battery used in
this charging device may present a risk of re or
chemical burn if mistreated. Do not disassemble,
expose to heat above 212°F (100°C) or incinerate.
- Misusing or incorrectly connecting the HALO charger
may cause electric shock to users and damage
equipment. The HALO charger may become warm
under extended high power operation. During
operation, keep the HALO charger away from materials
that may be aected by these temperatures.
- When used correctly, lithium-ion rechargeable
batteries provide a safe and dependable source of
portable power. However, if they are misused or
abused, this may result in leakage, burns, re or
explosion, causing personal injury or damage to other
devices.
- Do not disassemble the HALO charger. There are no
user-serviceable parts inside. Incorrect reassembly
may result in shock or re hazard.
- Do not drop or subject to strong impacts. Do not
operate the HALO charger if it has received a sharp
blow, or otherwise been damaged in any way.
- Do not expose the HALO charger to moisture, water,
rain, or snow.
- Do not insert any object into the ports or openings of
the HALO charger.
- Never charge the HALO charger unattended.
- There is a risk of the batteries exploding, overheating,
or igniting. Do not disassemble, modify, heat or
short-circuit the batteries. Do not place in re or leave
in hot places. Do not expose to direct sunlight.
- Only charge the HALO charger by the specied
method with the specied USB cable.
- In the unlikely event of leakage or explosion use sand
or a chemical re extinguisher.
- Batteries must be recycled or disposed of properly.
Battery Disposal
Special Battery Disposal Instruction for Lithium
Ion / LiPO, NiMH. LiFE cell:
Dispose of product with lithium ion battery in
accordance with your local battery recycling or
disposal laws.
Note: Opening of product and/or removal of battery
will render product inoperative and voids manufac-
turer warranties. Dispose of remaining product
components in accordance with local laws. DO NOT
dispose of unit with general waste. Return it to a
battery recycling center.
8
This HALO charger has been designed and manufac-
tured to ensure personal safety. Please read the
following carefully before using. Incorrect operation or
incompatibility with your personal electronic device
may result in reduced battery performance or damage.
- Carefully read the operating instructions, and use the
HALO charger correctly.
- Caution: The lithium-ion rechargeable battery used in
this charging device may present a risk of re or
chemical burn if mistreated. Do not disassemble,
expose to heat above 212°F (100°C) or incinerate.
- Misusing or incorrectly connecting the HALO charger
may cause electric shock to users and damage
equipment. The HALO charger may become warm
under extended high power operation. During
operation, keep the HALO charger away from materials
that may be aected by these temperatures.
- When used correctly, lithium-ion rechargeable
batteries provide a safe and dependable source of
portable power. However, if they are misused or
abused, this may result in leakage, burns, re or
explosion, causing personal injury or damage to other
devices.
- Do not disassemble the HALO charger. There are no
user-serviceable parts inside. Incorrect reassembly
may result in shock or re hazard.
- Do not drop or subject to strong impacts. Do not
operate the HALO charger if it has received a sharp
blow, or otherwise been damaged in any way.
- Do not expose the HALO charger to moisture, water,
rain, or snow.
- Do not insert any object into the ports or openings of
the HALO charger.
- Never charge the HALO charger unattended.
- There is a risk of the batteries exploding, overheating,
or igniting. Do not disassemble, modify, heat or
short-circuit the batteries. Do not place in re or leave
in hot places. Do not expose to direct sunlight.
- Only charge the HALO charger by the specied
method with the specied USB cable.
- In the unlikely event of leakage or explosion use sand
or a chemical re extinguisher.
- Batteries must be recycled or disposed of properly.
Battery Disposal
Special Battery Disposal Instruction for Lithium
Ion / LiPO, NiMH. LiFE cell:
Dispose of product with lithium ion battery in
accordance with your local battery recycling or
disposal laws.
Note: Opening of product and/or removal of battery
will render product inoperative and voids manufac-
turer warranties. Dispose of remaining product
components in accordance with local laws. DO NOT
dispose of unit with general waste. Return it to a
battery recycling center.
9
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
15.21
You are cautioned that changes or modications not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
15.105(b)
This equipment has been tested and found to comply
with the limits for Class B digital devices, pursuant to
Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment o and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver
- Connect the equipment into an outlet on a circuit
dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
10
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
15.21
You are cautioned that changes or modications not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
15.105(b)
This equipment has been tested and found to comply
with the limits for Class B digital devices, pursuant to
Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment o and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver
- Connect the equipment into an outlet on a circuit
dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Limited Warranty
Halo2Cloud, LLC warrants its products to be free from
defects in material and workmanship under normal
use conditions, as follows:
• During the rst one year from date of purchase,
Halo2Cloud, LLC will repair or replace the defective
product.
• Halo2Cloud, LLC will, subject to inspection, repair
the defective product or replace it with a new or
reconditioned unit. The return must be accompanied
by a Return Materials Authorization (RMA) number to
be issued upon request and must be shipped
prepaid. A shipping rebate will only be extended to
the customer in the event that a defect in material or
workmanship is conrmed.
• Warranty is void if the product has been improperly
handled or misused in any way, or if the label and/or
bar coded warranty label has been removed or
tampered with.
• Warranty returns require a check for $14.95 for
processing and handling made payable to
Halo2Cloud, LLC.
• Where applicable, all requests for warranty returns
must be accompanied by a proof of purchase and be
sent to Halo2Cloud, LLC (www.halo2cloud.com)
The warranty does not extend to the electronic
equipment that is used or which incorporates with
any of our products and accessories. Halo2Cloud, LLC
shall not be held responsible for the improper use of
its products.
For any questions email us at:
or call us:
888-907-6274
Halo2Cloud, LLC
148 Eastern Boulevard, Suite 210
Glastonbury, CT 06033
www.halo2cloud.com
11
Limited Warranty
Halo2Cloud, LLC warrants its products to be free from
defects in material and workmanship under normal
use conditions, as follows:
• During the rst one year from date of purchase,
Halo2Cloud, LLC will repair or replace the defective
product.
• Halo2Cloud, LLC will, subject to inspection, repair
the defective product or replace it with a new or
reconditioned unit. The return must be accompanied
by a Return Materials Authorization (RMA) number to
be issued upon request and must be shipped
prepaid. A shipping rebate will only be extended to
the customer in the event that a defect in material or
workmanship is conrmed.
• Warranty is void if the product has been improperly
handled or misused in any way, or if the label and/or
bar coded warranty label has been removed or
tampered with.
• Warranty returns require a check for $14.95 for
processing and handling made payable to
Halo2Cloud, LLC.
• Where applicable, all requests for warranty returns
must be accompanied by a proof of purchase and be
sent to Halo2Cloud, LLC (www.halo2cloud.com)
The warranty does not extend to the electronic
equipment that is used or which incorporates with
any of our products and accessories. Halo2Cloud, LLC
shall not be held responsible for the improper use of
its products.
For any questions email us at:
or call us:
888-907-6274
Halo2Cloud, LLC
148 Eastern Boulevard, Suite 210
Glastonbury, CT 06033
www.halo2cloud.com
12
/
