Simplicity GRASS BAGGER User manual

Brand: Simplicity

Model: GRASS BAGGER

Category: Lawnmowers

Type: User manual

Assembly

Operation

Maintenance

F–010900L TP-100-4291-00-AT-R

Repair Parts

CAUTION: Before using this

product, read this manual and

follow all its Safety Rules and

Operating Instructions.

Español

Operator’s Manual

GRASS BAGGER

Rear Mount, Dual Container

for 30” Rear Engine Rider

Model 502.249274

Safety

Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A.

F–010900L

TABLE OF CONTENTS

WARRANTY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

GRASS BAGGER FEATURES 2. . . . . . . . . . . . . . . . . . . .

CUSTOMER RESPONSIBILITIES 2. . . . . . . . . . . . . . . . .

ASSEMBLY 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO MOUNT THE FRAME ASSEMBLY 7. . . . . . .

HOW TO MOUNT THE COVER 8. . . . . . . . . . . . . . . . . .

HOW TO MOUNT THE EXTENSION TUBE 9. . . . . . . .

HOW TO MOUNT THE CONNECTOR TUBE 10. . . . . .

HOW TO ASSEMBLE THE CONTAINERS 11. . . . . . . .

HOW TO MOUNT THE CONTAINERS 12. . . . . . . . . . . .

HOW TO INSTALL THE FRONT WEIGHT 12. . . . . . . . .

CONTAINER LININGS 12. . . . . . . . . . . . . . . . . . . . . . . . . .

OPERATION 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

HOW TO USE THE GRASS BAGGER 13. . . . . . . . . . . .

CUSTOMER RESPONSIBILITIES 14. . . . . . . . . . . . . . . . .

HOW TO CLEAN THE GRASS BAGGER 14. . . . . . . . .

SLOPE GUIDE 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

LIMITED ONE YEAR WARRANTY

ON ATTACHMENTS

For one (1) year from the date of purchase, Sears will repair any defect in material or workmanship in this Attachment at no

charge.

This warranty does not cover:

●Expendable items which become worn during normal use, such as blades and blade adapters.

●Repairs necessary because of operator abuse, negligence, improper storage or accident or the failure to maintain the

equipment according to the instructions contained in the owner’s manual.

●Equipment used for commercial or rental purposes.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE ATTACHMENT TO THE NEAREST SEARS SERVICE

CENTER/DEPARTMENT IN THE UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Sears, Roebuck and Co., D/817WA, Hoffman Estates, Illinois 60179.

GRASS BAGGER FEATURES

See Through Window: Lets you know when the containers are

full.

Large Capacity Containers: Containers are quickly removed

and easy to empty.

GRASS BAGGER

Record in the space below the serial number and the date

of purchase of this unit.

The model number and serial number are found on a decal

attached to the unit.

Serial Number:

Date of Purchase:

Keep these numbers for future reference.

Model Number: 502.249274

Congratulations on your purchase of a Craftsman Grass Bagger.

It has been designed, engineered and manufactured to give you

the best possible dependability and performance.

If you experience any problems you cannot easily remedy, please

see your nearest Sears Service Department. We have

competent, well trained technicians and the proper tools to

service or repair this unit.

Please read and keep this manual. The instructions will enable

you to assemble and maintain your unit properly. Always observe

the “Safety Rules”.

CUSTOMER RESPONSIBILITIES

SCarefully read and follow the rules for safe operation. Inspect

the unit.

SFollow all the assembly instructions. Carefully adjust the unit.

SKnow how to operate all standard and accessary equipment

on the unit. Make sure the operator can correctly operate the

unit.

SOperate the unit only with guards, shields and other safety

items in place and working correctly.

SComplete all maintenance on the unit. Service the unit only

with authorized or approved replacement parts.

SAFETY RULES

F–010900L

Safe Operation Practices for Riding Vehicles

As Recommended by American National Standards Institute

WARNING: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury or death to the operator or bystanders.

GENERAL OPERATION:

1. Read, understand and follow all instructions in the Instruction

Book, on the machine, the engine and with any attachments

before starting.

2. Only allow responsible adults familiar with the instructions to

operate the machine.

3. Clear the area of objects such as rocks, toys, wire, etc.

which could be picked up and thrown by the blade.

4. Be sure the area is clear of other people before mowing.

Stop the machine if anyone enters the area.

5. Never carry passengers.

6. Disengage power to the mower or any attachments before

backing up. Do not mow in reverse unless absolutely neces-

sary. Always look down and behind before and while back-

ing.

7. Be aware of the direction the mower discharges. Do not point

discharge from the mower at anyone or at places where

people may be. Do not operate the mower without either the

entire grass bagger or the mower guard in place.

8. Slow down before turning.

9. Never leave a machine unattended with the engine running.

Always disengage the blade(s), set the parking brake, stop

the engine and remove the key before dismounting.

10. Disengage power to attachment(s) when transporting or not

in use. Disengage the blade(s) when not mowing.

11. Stop the engine before removing the grass bagger or unclog-

ging the chute.

12. Mow only in daylight or good artificial light.

13. Do not operate the machine while under the influence of al-

cohol or drugs or when very tired.

14. Watch for traffic when operating near or crossing roadways.

15. Use extra caution when loading or unloading the machine

when using a trailer or truck for transporting.

16. Disengage all attachment clutches and shift into Neutral be-

fore attempting to start the engine.

17. Always wear safety glasses or an eye shield when you oper-

ate the unit to protect your eyes from foreign objects that can

be thrown from the unit. Always wear eye protection when

you make an adjustment or repair to the machine.

18. Use care when pulling loads or using heavy equipment.

a. Use only approved drawbar hitch points.

b. Limit loads to those you can safely control.

c. Do not turn sharply. Use care when backing.

d. Use counterweights or wheel weights when suggested in

the Instruction Book.

19. Do not operate this machine if you are taking drugs or other

medication which can cause drowsiness or affect your ability

to operate this machine.

20. Do not use this machine if you are mentally or physically

unable to operate this machine safely.

21. Data indicates that operators, age 60 years and above, are

involved in a large percentage of riding mower related inju-

ries. These operators should evaluate their ability to operate

a riding mower safely enough to protect themselves and oth-

ers from serious injury.

SLOPE OPERATION:

Slopes and rough terrain are major factors related to loss of

control and tip over accidents which can result in severe

injury or death. ALL slopes require extra caution. If you can-

not back up the slope or if you feel uneasy on the slope, do

not mow it. See the “Slope Guide” in the back of this book to

check for safe operation.

1. Mow up and down slopes, not across.

2. Remove obstacles such as rocks, limbs, etc...

3. Watch for holes, ruts or bumps. Uneven terrain could over-

turn the machine. “Tall grass can hide obstacles.”

4. Use slow speed. Choose a low enough gear so that you will

not have to stop or shift while on the slope.

5. Follow the manufacturer’s recommendations for wheel

weights or counterweights to improve stability.

6. Use extra care with grass baggers or other attachments,

they can change the stability of the machine.

7. Keep all movement on the slopes slow and gradual. Do not

make sudden changes in speed or direction.

8. Avoid starting or stopping on a slope. If tires lose traction,

disengage the blades and proceed slowly straight down the

slope.

DO NOT

1. Do not turn on slopes unless absolutely necessary, then

only turn slowly and gradually downhill, if possible.

2. Do not mow near drop–offs, ditches or embankments. A

wheel over the edge or an edge caving in could cause a sud-

den overturn and an injury or death.

3. Do not mow on wet grass. Reduced traction could cause

sliding.

4. Do not try to stabilize the machine by putting your foot on

the ground.

5. Do not use a grass bagger or other rear mounted accesso-

ries on steep slopes (greater than 10 degrees).

CHILDREN:

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the ma-

chine and the mowing activity. NEVER assume that children

will remain where you last saw them.

1. Keep children out of the mowing area and in the watchful

care of an adult other than the operator.

SAFETY RULES

F–010900L

2. Be alert and turn the engine off if children enter the area.

3. Before and when backing, look behind and down for small

children.

4. Never carry children or any passengers. They may fall off

and be seriously injured or interfere with the safe operation

of the machine.

5. Never allow children to operate the machine. Instruct chil-

dren in the dangers of the machine.

6. Use extra care when approaching blind corners, shrubs,

trees or other objects that may obscure vision.

SERVICE:

1. Use extra care when handling gasoline and other fuels.

Fuels are flammable and the vapors are explosive.

a. Use only an approved container.

b. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool for several minutes before

refueling. Do not smoke.

c. Never refuel the machine indoors.

d. Never store the machine with fuel in the tank or fuel con-

tainer inside where there is an open flame, such as a water

heater.

2. Never start or run the engine inside a closed area.

3. Keep all nuts and bolts, especially the blade attachment nuts

tight. Frequently check the blade(s) for wear or damage such

as cracks and nicks. A blade that is bent or damaged must

be immediately replaced with an original equipment blade

from an authorized service dealer. For safety, replace the

blade every two years. Keep the equipment in good condi-

tion.

4. Never tamper with the safety devices. Check their proper

operation regularly.

5. To reduce fire hazards keep the machine free of grass,

leaves or other debris build–up. Clean up oil or fuel spills.

Allow the machine to cool before storing.

6. Stop and inspect the equipment if you strike an object. Re-

pair, if necessary, before restarting.

7. Never make adjustments or repairs with the engine running.

The carburetor can be adjusted with the engine running. Do

not change the engine governor settings or overspeed the

engine.

8. Grass bagger components are subject to wear, damage and

deterioration, which could expose moving parts or allow ob-

jects to be thrown. For storage, always make sure the grass

bag is empty. Frequently check components and replace with

manufacturer’s recommended parts when necessary.

9. Mower blade(s) are sharp and can cut. Wrap the blade(s) or

wear gloves and use extra caution when servicing them or

the blade housing area.

10. Check the brake operation frequently. Adjust and service as

required.

11. Wait for all movement to stop before servicing any part of the

unit.

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

ASSEMBLY

F–010900L

ASSEMBLY

Read and follow the assembly, operation and maintenance instruc-

tions. All fasteners are in the parts bag. Do not discard any parts or

material until the unit is assembled. Layout and identify all parts and

contents.

TOOLS REQUIRED

1. Pliers (1)

2. Adjustable open end wrenches (2

3. Blade type screwdriver (1)

4. Phillips screwdriver (1)

5. Short blade type screwdriver (1)

6. Open end wrenchs – 3/8”, 1/2”, 7/16”, 9/16”

7. Socket set recommended

HARDWARE PACKAGE – CONTENTS

The fasteners and other loose parts are shown below. The fasteners are shown at full size. The quantity is shown in brackets ( ).

On some models, all of the fasteners are not required.

6x93

(5) Special Bolt

5/16”–24x15/8”

26x239

(1) Screw

1/4”x3/4” AB

1x91

(4) Hex Bolt

5/16”–18x3/4”

STD523107

15x66

(6) Locknut

1/4”–20

STD541425

18x15

(5) Lockwasher

STD551131

15x32

(5) Hex Nut

5/16”–24

STD541131

2x39

(1) Carriage Bolt

1/4”–20x5/8”

STD532507 14x86

(2) Wingnut

2x64

(2) Carriage Bolt

STD533107

4x71

(1) Screw

1/4”–20x1”

STD512510

4x24

(5) Screw

1/4”–20x1/2”

STD512505

4x21

(3) Screw

#10–24x5/8”

STD511007

15x76

(5) Locknut

5/16”–18

STD541431

15x89

(2) Locknut

1/4”–20

STD541425

15x81

(3) Locknut

#10–24

STD541410

Not shown full size

54407Z

(1) Pin

Not shown full size

54408Z

(1) Pin

31x6

(1) Hair Pin

STD624003

193x1

(8) Fastener

Not shown full size

54695

(1) Latch

Not shown full size

54416E701

(1) Handle

Not shown full size

54537

(1) Handle

Not shown full size

54563

(1) Pin, Latch 24862

(3) Cap, End

24863

(1) Plug, Weight

ASSEMBLY

F–010900L

LOOSE PARTS – CONTENTS

Container

Sections

Blade

Container

Sections

Cover

Hinge

Outer Tube

Inner Tube

Channel

Elbow

Connector Tube

Frame Bracket

Support Bracket

Extension Tube

Front Weight

Weight Bracket

Literature Kit

Hardware Pack

Window Bag

ASSEMBLY

F–010900L

HOW TO MOUNT THE FRAME ASSEMBLY

IMPORTANT: Note the bolt shown in Figure 1 that was

installed at the factory. Use this bolt to attach the frame

bracket.

1. Mount the frame bracket onto the factory installed bolt

shown in Figure 1.

2. Hold the support bracket on the inside of the frame. Align

the holes in the support bracket with the holes in the frame

and the frame bracket. Fasten with the fasteners shown full

size below. Tighten the fasteners only with your fingers.

(A)

1x91 (B)

15x76

3. Carefully follow the procedure below to tighten the fasteners.

This procedure is necessary to lock the frame bracket and

the support bracket in place. See the procedure steps in

Figure 1.

First: Tighten bolt (A), located next to the tire, with a wrench.

Next: Tighten the two bolts (A), located at the back of the frame.

Last: Tighten the top two fasteners.

Figure 1

Frame Bracket

Bolt (Installed

at factory)

Support Bracket

Tighten First

Tighten Next

Tighten Last

4. Mount the channel in the frame bracket (Figure 2).

IMPORTANT: If you remove the grass bagger to mount a

different pull–behind attachment, do not remove the

frame bracket. Use the hitch pin hole in the frame

bracket to mount a different attachment.

5. Install the channel pin into the right side of the channel

(Figure 3). Rotate the channel pin counterclockwise to lock

the channel in place.

6. Mount the outer tube to the channel. Make sure the two

holes, on the side of the outer tube, are on the right side

(Figure 3). Use the fasteners shown full size below. Make

sure the fasteners are tight.

(C)

6x93 (D)

18x15 (E)

15x32

Figure 2

Channel

Frame Bracket

Hitch Pin Hole

Figure 3

Channel Pin

Channel

Channel Pin

Rotate Counterclockwise

Outer Tube

Two Holes

on right side

Figure 4

Center Tube

Channel

Cap

7. Mount the center tube to the channel (Figure 4). Make sure

the fasteners are tight.

8. Attach the caps to the ends of the tubes (Figure 4).

ASSEMBLY

F–010900L

HOW TO MOUNT THE COVER

1. Assemble the hinge to the cover (Figure 5). The fasteners

are shown full size below. Push the hinge toward the top of

the cover. Make sure the screws are at the bottom of the

holes in the hinge. Tighten the fasteners.

(A)

4x24 (B)

15x66

2. Attach the handle to the cover with the fasteners as shown.

Tighten the fasteners.

3. Attach the window to the cover with the fasteners

(Figure 6). Make sure the flange and the two tabs are

locked inside the cover.

(C)

4x21 (D)

15x81

4. Set the cover in the operating position on top of the outer

tube. Fasten the hinge to the channel with the fasteners

shown below.

(E)

54407Z

(F)

31x6

(Not Shown Full Size)

Figure 5

Hinge

Handle

Cover

Figure 6

Cover

Channel

Window

Flange

Tab

ASSEMBLY

F–010900L

HOW TO MOUNT THE EXTENSION TUBE

1. Attach latch pin (A) to the extension tube with the fasteners

shown full size below (see Figure 8).

(A)

54563 (B)

15x89 (C)

2x39

(Not Shown Full Size)

2. Engage the parking brake.

3. Disconnect the wire from the spark plug (see Figure 7).

Figure 7

Spark Plug

4. Move the lift lever to the lowest cut position.

5. Raise the deflector (see Figure 8). If a mulch cover is

installed, remove the mulch cover. Use the mulch cover

hardware to attach the extension tube. If a mulch cover is

not installed, use the fasteners in the parts bag.

6. Rotate the blade away from the discharge opening.

WARNING: The blade has sharp edges. Always be

careful of the position of the blade.

7. Slide the tabs of the extension tube bracket under the de-

flector (Figure 8).

8. Slide the extension tube bracket toward the front

(Figure 9). Make sure the tabs on the extension tube

bracket lock behind the nuts (Figure 10).

9. Move the lift lever to the highest cut position.

10. Attach the bottom of the extension tube to the mower hous-

ing with the fasteners shown full size below.

(D)

2x64

(E)

14x86

a. First, install bolt (D) to the front of the extension tube.

Fasten with wingnut (E) on the outside (Figure 10).

Make sure the wingnut is tight.

b. Next, reach through the extension tube. Install bolt (D)

to the rear of the extension tube. Fasten with wingnut

(E). Push the back of the extension tube until bolt (D) is

at the top of the slot. Tighten wingnut (E).

11. Connect the wire to the spark plug.

Figure 8

Deflector

Extension Tube

Extension

Tube Bracket

Figure 9

Slide the bracket toward the front.

Tab

Deflector

Extension Tube

Figure 10

Deflector

Tab locked

behind nut. Tab locked

behind nut.

Make sure bolt D

is at top of slot.

Extension Tube

Extension Tube Bracket

ASSEMBLY

F–010900L

HOW TO MOUNT THE CONNECTOR TUBE

Mount the connector tube with the fasteners shown full size below.

(A)

26x239 (B)

15x89 (C)

4x24

(D)

4x71 (E)

15x66

1. Assemble the handle and the to the connector tube with

the fasteners (see Figure 11). Hold screws (C) and (D) with a

short screwdriver and tighten locknuts (E).

2. Attach the rubber latch to the handle with nut (B) (see

Figure 11).

3. Align the two holes in the connector tube with the hole on

the elbow. Slide the connector tube into the elbow until the

second line on the decal is even with the edge of the elbow.

4. Fasten the elbow to the connector tube with screw (A).

Push screw (A) through the hole on the elbow. Tighten

screw (A) until the head of the screw touches the elbow.

5. Move the lift lever to the lowest position.

6. Hold the handle on the connector tube and push the elbow

into the hole in the cover (Figure 12).

7. Align the rubber latch with the latch pin (Figure 13).

8. Slide the connector tube over the extension tube.

9. Lock the rubber latch to the latch pin.

Figure 11

Handle

Rubber

Latch

Decal

Align the holes.

Elbow

Connector Tube

Figure 12

Handle

Cover Elbow

Connector Tube

Figure 13

Connector

Tube

Extension Tube

Lock Rubber Latch

To Latch Pin

ASSEMBLY

F–010900L

HOW TO ASSEMBLE THE CONTAINERS

NOTE: The containers can only be assembled one way.

Carefully read and follow the instructions below.

1. Separate the six container sections into two groups. Each

group will have a top section, a middle section, and a bottom

section (Figure 14).

2. Look for a number on the side of each top section. The num-

bers for the two top sections are 1 and 3. Set the two top sec-

tions on the ground with the flanges on top.

3. Look for the numbers on the side of each middle section. One

middle section has the numbers 1 – 2. The other middle sec-

tion has the numbers 3 and 4.

4. Set middle section 1 – 2 inside of top section 1.

5. Set middle section 3 – 4 inside of top section 3.

6. Look for a number on the side of each bottom section. The

numbers for the two bottom sections are 2 and 4.

7. Set bottom section 2 inside of middle section 1 – 2.

8. Set bottom section 4 inside of middle section 3 – 4.

9. Stand with one foot inside the three sections (Figure 15). Lift

the top section until all three sections connect together. Make

sure all four corners of each section are locked together.

10. Fasten the top section and the middle section of each con-

tainer together with four fasteners A shown below. From the in-

side of each container, push the fasteners through the holes

(Figure 16).

(A)

193x1

Figure 14

Bottom Section

Middle Section

Top Section

Flange

Figure 15

Bottom Section

Middle Section

Top Section

Figure 16

Bottom Section

Middle Section

Top Section

ASSEMBLY

F–010900L

HOW TO MOUNT THE CONTAINERS

1. Tilt the seat forward. Raise the cover (Figure 17).

2. If desired, put the optional plastic bag linings in the

containers.

3. Slide the containers onto the frame tubes. Make sure the

CAUTION, on the side of the containers, is to the rear.

4. Lower the cover. To lock the cover in place, pull back on the

handle, push the cover down and release the handle.

IMPORTANT: For the grass bagger to work correctly, the

cover must be locked in the down position. Figure 17

Handle

Cover

Frame Tubes

Containers

Caution

to rear

HOW TO INSTALL THE FRONT WEIGHT

1. To find the mounting location for the weight brackets, look

under the frame at the square holes (Figure 18). Lock the

tabs on the weight brackets in the square holes. Fasten-

ers are not required.

2. Set the front weight on the weight brackets.

3. Fill the front weight with sand. Install the plug.

CAUTION: Removal of the front weight will also require the

removal of the weight brackets.

WARNING: Use the front weight when you operate

on a slope or where the lawn is rough or is not

even.

WARNING: Do not ride up or down slopes that are

too steep to back straight up. Never ride the unit

across a slope. See the “Slope Guide” in the back

of this book for information on how to check

slopes. Figure 18

Slide Tab Forward

Weight Bracket

Tab

Square Hole

Plug

Front Weight

CONTAINER LININGS

Plastic bag linings are optional accessories that can be used for

easy removal of the grass. Use one of the following sizes.

 33 gallons

 4 bushels

 145 liters

HIGH–LIFT BLADE

There are several different types of grass. Some types of grass

make filling the bag more difficult. A high–lift blade is included

with the grass bagger. If the bag does not fill properly, replace the

standard blade with the high–lift blade. To replace the blade(s),

follow the instructions in the mower instruction book.

OPERATION

F–010900L

HOW TO USE THE GRASS BAGGER

WARNING: Do not ride up or down slopes that are too

steep to back straight up. Never ride the unit across

a slope. See the “Slope Guide” in the back of this

book for information on how to check slopes.

OPERATION

To operate with the grass bagger, follow the steps below.

IMPORTANT: Do not cut wet grass. Wet grass will not

discharge correctly into the grass bagger.

1. Start the engine.

2. Move the throttle control to FAST position.

3. Move the shift lever to FIRST (1) position. To fill the containers,

always operate at the slowest speed.

4. If the height of the grass is more than 31/2 inches (9cm), cut the

grass with the mower housing in the highest position. Then,

lower the mower housing and cut the grass again. You can also

cut at 1/2 to 2/3 of the full cutting width of the mower housing.

CHECK AND CLEAN CONNECTOR TUBE

The connector tube is made of clear plastic. If the connector tube

becomes filled with grass, clean the connector tube as follows.

1. Move the attachment clutch to the DISENGAGE position.

2. Move the shift lever to the neutral (N) position.

3. Engage the parking brake.

4. Stop the engine.

5. Disconnect the rubber latch from the extension tube

(Figure 19).

6. Remove the connector tube.

7. Clean the connector tube and the extension tube with soap

and water.

HOW TO EMPTY THE CONTAINERS

Look at the window in the cover (Figure 20). When the containers

are full, grass can be seen through the window. Empty the

containers as follows.

1. Move the attachment clutch to the DISENGAGE position.

2. Move the shift lever to the neutral (N) position.

3. Engage the parking brake.

4. Stop the engine.

5. Tilt the seat forward.

6. Pull the handle back and raise the cover.

7. Remove the containers.

Figure 19

Connector

Tube

Extension Tube

Rubber Latch

Figure 20

Handle

Cover

Frame Tubes

Containers

Caution

to rear

Window

MAINTENANCE

F–010900L

HOW TO CLEAN THE GRASS BAGGER

WARNING: Before you clean the grass bagger, stop

the engine and disconnect the wire to the spark plug.

For good performance, frequently clean the grass bagger as

follows.

1. Disconnect the rubber latch from the extension tube

(Figure 21).

2. Remove the connector tube from the extension tube.

3. Remove the elbow and connector tube from the cover.

4. Clean the connector tube, the extension tube, and the

elbow with soap and water.

5. Raise the cover.

6. Clean the window with soap and water.

Figure 21

Cover

Window

Extension Tube

Rubber Latch

Connector Tube

Elbow

15F–010900L

REPAIR PARTSMODEL 502.249274

F–010900L

GRASS BAGGER

36 36

152

51 52 53

11 10

20 21

43 42 25

REPAIR PARTSMODEL 502.249274

F–010900L

GRASS BAGGER

Key

No. Description Part No. Mfg. No.

1 Window 54575

2 Cover 54577

3 Screw STD512505 4x24

4 Locknut STD541425 15x66

5 Tube, “U”54410E701

6 Pin, Hair STD624003 31x6

7 Pin, Hinge 54407Z

8 Tube, Center 54412E701

9 Bolt, Special 6x93Z

10 Lockwasher STD551131 18x15

11 Nut, Hex STD541131 15x32

12 Channel Assembly 54422E701

13 Pin, Channel 54408Z

14 Bolt, Hex STD523107 1x91

15 Hitch Assembly 54499E701

17 Cap, End 24862

18 Elbow 54415

20 Handle, Connector Tube 54416E701

21 Locknut, Flange STD541425 15x89

22 Latch, Rubber 54695

23 Wingnut STD541631 14x83

24 Tube, Chute Extension 54519

25 Locknut STD541431 15x76

26 Pin, Latch 54563

27 Bolt, Carriage STD532507 2x39

29 Tube, Connector 54555

30 Screw STD512510 4x71

31 Hinge, Cover 54398E701

36 Fastener, Plastic * 193x1

37 Containers (Quantity 2) 54727SE

41 Bolt, Carriage STD533107 2x64

42 Shell, Front Weight 55442

43 Plug, Front Weight 24863

45 Bracket, Front Weight 54551E701

47 Bracket, Support 54562E701

48 Screw 26x239

51 Handle, Plastic 54537

52 Screw STD511007 4x21

53 Nut, Hex STD541410 15x81

54 Blade, High–Lift 56246E701

–Owner’s Manual F–010900L

* Included with Key No. 37.

F–010900L

CONTENIDO

GARANTÍA18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CARACTERÍSTICAS DEL RECOLECTOR DE HIERBA 18. . . . . . .

RESPONSABILIDADES DEL PROPIETARIO 18. . . . . . .

REGLAS DE SEGURIDAD 19. . . . . . . . . . . . . . . . . . . . . . .

ENSAMBLAJE 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CÓMO MONTAR EL BASTIDOR 23. . . . . . . . . . . . . . . . .

CÓMO MONTAR LA CUBIERTA 24. . . . . . . . . . . . . . . . .

CÓMO MONTAR EL TUBO DE EXTENSIÓN25. . . . . .

CÓMO MONTAR EL TUBO CONECTOR 26. . . . . . . . .

CÓMO ENSAMBLAR LOS RECIPIENTES 27. . . . . . . .

CÓMO CONECTAR LOS RECIPIENTES 28. . . . . . . . . .

CÓMO INSTALAR EL PESO DELANTERO 28. . . . . . .

OPERACIÓN29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CÓMO USAR EL RECOLECTOR DE HIERBA 29. . . . .

MANTENIMIENTO 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CÓMO LIMPIAR EL RECOLECTOR DE HIERBA 30. .

GUIA DE INCLINACION 31. . . . . . . . . . . . . . . . . . . . . . . . .

GARANTÍA LIMITADA DE UN AÑO

PARA ADITAMENTOS

Durante un (1) año a partir de la fecha de compra, Sears reparará sin cargo alguno, cualquier defecto en el material o mano

de obra de este aditamento.

Esta garantía no cubre lo siguiente:

●Elementos de desgaste normal, tales como cuchilla y adaptadores de cuchilla.

●Reparaciones necesarias debido al abuso o negligencia del operador, incluyendo almacenamiento inadecuado o

accidentes, o a la falta de mantenimiento de la unidad de acuerdo a las instrucciones presentadas en el manual del

propietario.

●Equipo que ha sido utilizado con fines comerciales o de arrendamiento.

EL SERVICIO DE GARANTÍA ESTÁ DISPONIBLE LLEVANDO EL ADITAMENTO AL CENTRO/DEPARTAMENTO DE

SERVICIO SEARS MÁS CERCANO, EN LOS ESTADOS UNIDOS.

Esta garantía le proporciona derechos legales específicos, y es posible que tenga otros derechos los cuales varían de estado

a estado.

Sears, Roebuck and Co., D/871WA, Hoffman Estates, Illinois 60684.

CARACTERÍSTICAS DEL RECOLECTOR DE HIERBA

Ventanilla: Le indica cuando los recipientes están llenos.

Recipientes de gran capacidad: Estos recipientes se pueden

desmontar y vaciar rápida y fácilmente.

Recolector de hierba

En el espacio indicado a continuación anote el número de

serie y la fecha de compra de la unidad.

El número de modelo y el número de serie se encuentran

en la calcomanía ubicada en la parte trasera del bastidor.

Número de Modelo: 502.249274 ________

Número de Serie:

Fecha de Compra:

Guarde estos números para referencias futuras.

Felicitaciones por su compra de un aditamento recolector de

hierba Craftsman para su cortacésped. Este recolector de hierba

ha sido diseñado, adaptado y fabricado con el propósito de

ofrecerle la mayor seguridad y rendimiento posibles.

Si tiene cualquier problema técnico que no pueda solucionar

fácilmente, por favor visite su Departamento de Servicio Sears

más cercano. Tenemos técnicos competentes y bien entrenados

que cuentan con las herramientas apropiadas para revisar y

reparar esta unidad.

Por favor lea y guarde este manual. Las instrucciones en este

manual le permitirán ensamblar y mantener su unidad

adecuadamente. Tenga siempre en cuenta las “Reglas de

Seguridad”.

RESPONSABILIDADES DEL PROPIETARIO

SLea y siga cuidadosamente las reglas de seguridad para una

operación segura. Inspeccione la unidad.

SSiga todas las instrucciones de ensamblaje. Ajuste la

unidad cuidadosamente.

SAprenda a operar bien todo el equipo estándar y accesorio

de la unidad. Asegúrese de que el operador pueda operar la

unidad correctamente.

SOpere la unidad sólo con los dispositivos de seguridad, los

protectores y otros elementos de seguridad en su lugar y

funcionando correctamente.

SComplete todos los pasos de mantenimiento para la unidad.

Utilice sólo piezas de repuesto autorizadas o aprobadas.

ENSAMBLAJE

F–010900L

REGLAS DE SEGURIDAD

Prácticas de operación segura para vehículos autoportados

Basadas en las recomendaciones del Instituto de Estándares Nacionales de Estados Unidos de América

PRECAUCION: Esta máquina cortadora es capaz de amputar manos y pies y de lanzar objetos con mucha fuerza. No

respetar las instrucciones de seguridad a continuación podría resultar en lesiones graves o la muerte del operador o

de espectadores.

OPERACIÓN GENERAL:

1. Antes de comenzar el trabajo, lea, entienda y siga todas las

instrucciones que aparecen en el Manual de Instrucciones,

en la máquina, en el motor y en cualquiera de los aditamen-

tos.

2. Sólo permita que adultos responsables, familiarizados con

las instrucciones, utilicen la máquina.

3. Despeje el área de objetos tales como piedras, juguetes,

cables, etc., que podrían ser lanzados con fuerza por la cu-

chilla.

4. Antes de comenzar a cortar el césped, asegúrese de que no

haya ninguna persona en el área. Si alguien entra en el

área, pare de inmediato la máquina.

5. Nunca lleve pasajeros.

6. Antes de retroceder, desconecte la alimentación al cortacés-

ped o a cualquier aditamento que tenga instalado. No corte

el césped en reversa a menos que esto sea absolutamente

necesario. Siempre mire hacia abajo y hacia atrás antes de

retroceder y mientras retrocede.

7. Esté atento a la dirección de descarga de la hierba cortada.

No dirija la descarga hacia personas o hacia lugares donde

pudiera haber gente. No opere la unidad sin tener instalado

el recolector de hierba o el dispositivo de seguridad.

8. Aminore la velocidad antes de dar la vuelta.

9. Nunca deje una máquina desatendida mientras el motor está

en marcha. Siempre desembrague la cuchilla(s), enganche

el freno de mano, pare el motor y retire la llave antes de ba-

jarse.

10. Desconecte la alimentación a los aditamentos cuando no los

esté utilizando o cuando transporte la unidad. Desembrague

la cuchilla(s) cuando no esté cortando el césped.

11. Pare el motor antes de desmontar el recolector de hierba o

para desobtruir el conducto de descarga.

12. Corte el césped a la luz del día o con buena luz artificial.

13. No opere la máquina si está bajo los efectos del alcohol o de

drogas, o si está muy cansado.

14. Esté atento al tráfico cuando opere la máquina cerca de ca-

minos o si debe cruzarlos.

15. Si usa un remolque o camioneta para transportar la unidad,

tenga mucho cuidado al cargar o descargar la unidad del

vehículo.

16. Desenganche todos los embragues de los aditamentos y

coloque la palanca de cambios en la posición neutro antes

de arrancar el motor.

17. Siempre use gafas de protección u algún tipo de protector

para los ojos cuando utilice la unidad, de esta manera prote-

gerá sus ojos de objetos que pudieran ser lanzados por la

máquina. Este tipo de protección ocular también debe usar-

lo cuando necesite hacer ajustes o reparaciones a la máqui-

na.

18. Tenga mucho cuidado cuando deba remolcar cargas o cuan-

do utilice equipos pesados.

a. Utilice únicamente barras de enganche con puntos de

remolque aprobados.

b. Limite las cargas a aquellas que usted pueda controlar

con seguridad.

c. No gire el volante bruscamente. Tenga cuidado al retro-

ceder.

d. Utilice contrapesos o pesos en las ruedas cuando esto

sea recomendado en el Manual de Instrucciones.

19. No opere esta máquina si está tomando drogas u otras me-

dicinas que pudieran causar somnolencia o que pudieran

afectar su habilidad para operar esta máquina.

20. No opere esta máquina si su estado emocional o físico no le

permite operarla con seguridad.

21. Los datos recopilados indican que los operadores de 60

años o más, sufren un mayor número de accidentes y lesio-

nes relacionados con el manejo de máquinas cortacésped.

Estos operadores deben evaluar sus habilidades para mane-

jar de manera segura un tractor cortacésped y evitar así le-

siones graves que pudieran sufrir ellos u otras personas que

se encuentren presentes.

OPERACIÓN EN CUESTAS:

Las cuestas y los terrenos accidentados son factores princi-

pales que se relacionan a accidentes causados por pérdidas

de control o por vuelcos de la unidad y que pueden resultar

en lesiones graves o muerte. TODAS las cuestas requieren

que se tomen precauciones adicionales. Si no puede subir

la cuesta usando el cambio de marcha atrás, o si se siente

incómodo en la cuesta, no la corte. Consulte la “Guía de

evaluación de cuestas”. Para obtener mayor información al

respecto, consulte esta guía que aparece al final de este ma-

nual.

RECOMENDACIONES

1. En las cuestas, corte el césped verticalmente (hacia arriba y

hacia abajo), y no en línea perpendicular (de lado a lado).

2. Quite todo obstáculo tal como piedras, ramas, etc.

3. Tenga cuidado con los hoyos, baches o resaltos. El terreno

disparejo puede hacer que la máquina se vuelque. “La hier-

ba muy alta puede esconder obstáculos”.

4. Maneje la unidad a baja velocidad. Seleccione una veloci-

dad suficientemente baja para que no tenga que parar o

cambiar de velocidad mientras está en la cuesta.

5. Respete y siga las recomendaciones del fabricante acerca

de pesos para las ruedas o contrapesos para mejorar la es-

tabilidad.

6. Tenga mucho cuidado cuando utilice el recolector de hierba

u otros aditamentos, estos afectan la estabilidad de la má-

quina.

ENSAMBLAJE

F–010900L

7. Procure que todos los movimientos en las cuestas sean len-

tos y graduales. No haga cambios bruscos de velocidad o

de dirección.

8. Evite tener que arrancar el motor o pararlo en una cuesta.

Si los neumáticos pierden tracción, desembrague la cuchi-

lla(s) y continúe despacio directamente hacia el pie de la

cuesta.

PRECAUCIONES

1. No gire en las cuestas a menos que sea absolutamente ne-

cesario, si debe hacerlo, gire lenta y gradualmente cuesta

abajo, si es posible.

2. No corte el césped cerca de precipicios, zanjas o terraple-

nes. Una rueda sobre un borde o el desprendimiento de un

borde podría causar un vuelco inesperado provocando lesio-

nes o la muerte.

3. No corte el césped si está mojado. La reducida tracción

puede hacer que la máquina resbale.

4. No trate de estabilizar la máquina bajando su pie al suelo.

5. No utilice el recolector de hierba ni otro accesorio de remol-

que en cuestas empinadas (de más de 10 grados).

NIÑOS:

Pueden ocurrir accidentes trágicos si el operador no está

alerta a la presencia de niños. A muchos niños les atraen

las cortadoras autoportadas. NUNCA suponga que los ni-

ños permanecerán en el último lugar donde los vió.

1. Mantenga a los niños fuera del área de trabajo y bajo el cui-

dado de un adulto que no sea el operador.

2. Manténgase alerta y pare el motor si entran niños al área.

3. Antes y mientras retrocede, mire hacia atrás y hacia abajo

por si hay niños.

4. Nunca permita que niños u otras personas vayan como “pa-

sajeros” en el cortacésped. Ellos pueden caerse , lesionarse

gravemente o pueden interferir con la operación segura de la

máquina.

5. Nunca permita que niños operen la máquina. Enséñeles a

los niños los peligros de la máquina.

6. Tenga mucho cuidado cuando se aproxime a esquinas cie-

gas, arbustos, árboles u otros objetos que le impidan una

buena visibilidad.

SERVICIO:

1. Tenga mucho cuando manipule gasolina y otros combusti-

bles. Los combustibles son inflamables y los vapores son

explosivos.

a. Utilice únicamente un recipiente aprobado.

b. Nunca quite la tapa del tanque de gasolina ni añada com-

bustible cuando el motor esté en marcha. Deje que el motor

se enfríe durante varios minutos antes de llenar el tanque.

No fume cuando llene el tanque.

c. Nunca agregue combustible cuando la unidad se encuen-

tra en un recinto cerrado.

d. Nunca guarde el cortacésped con combustible en el tan-

que, o el recipiente de combustible en un recinto donde haya

alguna llama expuesta, tal como el piloto de un calentador

de agua.

2. Nunca arranque el motor ni lo deje en marcha dentro de un

recinto cerrado.

3. Mantenga todas las tuercas y pernos apretados, especial-

mente las tuercas de montaje de la cuchilla(s). Revise con

frecuencia la cuchilla(s) para ver si está gastada o si tiene

algún daño tal como grietas o abolladuras. Una cuchilla tor-

cida o dañada debe ser reemplazada inmediatamente por

una cuchilla de repuesto original la cual puede obtener en un

centro de servicio autorizado. Para mayor seguridad, reem-

place la cuchilla cada dos años. Mantenga el equipo en

buenas condiciones.

4. Nunca trate de modificar los dispositivos de seguridad. Re-

víselos con frecuencia para cerciorarse de que trabajan

bien.

5. Para reducir los riesgos de incendio, mantenga la máquina

libre de acumulaciones de hierba, hojas u otros desechos.

Limpie derrames de aceite o de combustible. Deje que la

máquina se enfríe antes de guardarla.

6. Pare e inspeccione el equipo si choca contra algún objeto.

Si es necesario, repare el equipo antes de hacerlo arrancar

de nuevo.

7. Nunca realice ajustes o reparaciones con el motor en mar-

cha. El carburador puede ser ajustado mientras el motor

está en marcha. No cambie los ajustes del regulador del

motor ni sobrepase la velocidad de régimen del motor.

8. Los componentes del recolector de hierba están sujetos a

desgaste, daño y deterioro, factores que pueden exponer las

partes móviles o permitir que objetos sean lanzados por la

máquina. Al guardar la unidad, asegúrese siempre de que el

recolector de hierba esté vacío. Revise los componentes

periódicamente, y cuando sea necesario, reemplácelos con

piezas de repuesto recomendadas por el fabricante.

9. La cuchilla(s) de la cortadora es afilada y puede cortarle.

Envuelva la cuchilla(s) o utilice guantes y tome precauciones

cuando tenga que revisarla o revisar el área del alojamiento

de la cuchilla.

10. Examine los frenos frecuentemente. Ajústelos y revíselos

según sea necesario.

11. Antes de comenzar a revisar cualquier parte de la unidad,

espere a que todo movimiento se detenga.

Fíjese en este símbolo, éste le indica precauciones de seguri-

dad importantes. Este símbolo significa: “Atención! Esté

alerta! Su seguridad está en peligro”.

Page is loading ...

Simplicity GRASS BAGGER User manual

Brand: Simplicity

Model: GRASS BAGGER

Category: Lawnmowers

Type: User manual

Download PDF

report

in other languages

español: Simplicity GRASS BAGGER Manual de usuario

Simplicity GRASS BAGGER User manual

Simplicity GRASS BAGGER User manual

in other languages

Related papers

Other documents