CLS Mika ColourFlow & Tunable White Owner's manual

Brand
CLS
Model
Mika ColourFlow & Tunable White
Type
Owner's manual
www.cls-led.com www.cls-led.com
h
Ceiling 350º 58º 23 cm 18 cm 1325 gr 50.000 h 22º 47º 67º IP20
Max.
30 Watt
ø
1800-4000KRGBW
2700-5700K
DRIVER
INCLUDED
DRIVER
EXTERNAL
RGBA
DMX
512
CLS
DYNAMIC
COLOUR
COB
100 - 240
VAC
2
CLS MIKA COLOUR FLOW SERIESCLS MIKA COLOUR FLOW SERIES
Manual V1.0 - May 2020
INDEX
Index 2
Safety information 2
Content 2
Technical 3
Specifications 3
Accessories 3
Installation 4
CONTENT
SAFETY INFORMATION
Always switch o mains power
of the driver before connecting
or maintaining any fixtures!
Qualified
technician
Ambiance
Max. 40º
Do not stare
into the LED
Block access
below the work
area when
maintaining
the unit
Use a source
of AC power
that complies to
local electrical
codes
Make sure all
connectors are
connected
properly
Don’t install in
a flammable
or explosive
area
Warning!
Some surfaces
can be hot
Don’t modify
or install
genuine parts
on this product
Wiring on the LDC-407 driver 4
Programming 5
Factory setting table 5
Programming table 6
Reflector replacement 7
List of symbols 8
h
Ceiling 350º 58º 23 cm 18 cm 1325 gr 50.000 h 22º 47º 67º IP20
Max.
30 Watt
ø
1800-4000KRGBW
2700-5700K
DRIVER
INCLUDED
DRIVER
EXTERNAL
RGBA
DMX
512
CLS
DYNAMIC
COLOUR
COB
100 - 240
VAC
www.cls-led.com www.cls-led.com
3 4
TECHNICAL
+43°
ø 200 mm
-15°
ø 180 mm
cut-out size
173 mm
Tools
ø 18 cm
SPECIFICATIONS
LED: Dynamic Colour Chip
Available colours: RGBW & RGBA
Tunable White: 1800K-4000K & 2700-5700K
Beam angle: 22º, 47º or 67º
Power supply: 100-240 VAC
Power consumption: Max. 30 Watt
Housing: Black, or white coated aluminium,
Black PC (PC-ABS V0)
Weight: 1325 gram
IP value: IP20
Measurements: 173 x 200 mm (hxø)
Ambient temperature: -10º C till +40º C
LDC-407 DMX LED driverMika series
35 mm
222 mm
50 mm
Magnet point
INSTALLATION
min. 23 cm ø 18 cm
Suspended
ceiling:
23 cm space
is required for
ventilation
Cut-outsize
WIRING OF THE LDC-407 DRIVER
www.cls-led.com www.cls-led.com
65
PROGRAMMINGTABLE
DMX
Function
Data
Parameters
Description
CH1
Setaddress
001to255
0
0=nochange
UsethisDMXchanneltosetaddressfrom001to
255.TheconfiguredDMXaddressiscalled“n”
1…255
DMXaddress=1…255
CH2
Setaddress
256to508
0
nochange
UsethisDMXchanneltosetaddressfrom256to
508.TheconfiguredDMXaddressiscalled“n”
1…255
DMXaddress=256…508
CH3 Static
behavior
0
nochange
IfnoDMXispresentthefixturewillrespondlike
setinthisfunction.
1
lastDMXvalue
2
outputoff
3
loadstaticvalues
CH4 Softdim
0
nochange
SoftdimwillinterpolatebetweentheDMX
values.Thisfunctionmakesthedimcurve
smoother
1
off
2
on
CH5 Master
control
0
nochange
Ifmasterisfirstchannelisselectedthechannel
willbeDMXchannel“n”.Ifmasterislastchannel
isselectedthechannelwillbe“n+x”
(“x”iscalculatedintheoutputpatch).
1
nomasterused
2
masterisfirstchannel
3
masterislastchannel
CH6 Output1
patch
0
nochange
Eachoutputchannelcanbepatchedtorespond
tothedesiredDMXchannel.Thisenablesthe
usertomixupthecoloursaccordingtothe
controllerthatisused.
Example:alloutputsarepatchedas1
AlloutputswillbecontrolledbyDMXchannel
“n”.IfmasterisusedtotalDMXchannelswillbe2
otherwiseituses1channel(“x”=1).
Example:output1&2arepatchedas1and3&4
arepatchedas2
Output1&2willbecontrolledbyDMXchannel
“n”.
Output3&4willbecontrolledbyDMXchannel
“n+1”.
IfmasterisusedtotalDMXchannelswillbe3
otherwiseituses2channels(“x”=2).
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH7Output2
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH8 Output3
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH9Output4
patch
0
nochange
1
DMXchanneln
2
DMXchanneln+1
3
DMXchanneln+2
4
DMXchanneln+3
CH10Staticoutput
1
0
nochange
Eachoutputchannelcanbesettoanstatic
intensity.
IfnoDMXispresentandStaticbehaviorissetto
“loadstaticvalues”.Theoutputswillbesettothe
configuredintensityvalues.
1
outputoff
2…255
intensity2…255
CH11Staticoutput
2
0
nochange
1
outputoff
2…255
intensity2…255
CH12Staticoutput
3
0
nochange
1
outputoff
2…255
intensity2…255
CH13Staticoutput
4
0
nochange
1
outputoff
2…255
intensity2…255
CH14Loaddefault
settings
0
nochange
ThisfunctionresetsallsettingstotheFactory
setting.CheckFactorysettingtable.
X
LoadFactorysettings.Xisrow
numberfactorysettingtable.
PROGRAMMING TABLE
FACTORY SETTING TABLE
PROGRAMMING
123
* If the LEDs ashes 10 times, something went wrong. Please try again. If the problem continues to occur, please contact your local sales distributor.
Place magnet
at the bottom
of the LDC-407.
The LED of the
Mika will
light up
After 2 seconds
the LED will ash
3 times
conrming
storage*
All settings can be configured via DMX. Settings can be configured at once or separately. When one or a couple settings needs to be
changed just leave all other setting values zero. This keeps those settings unchanged. Please check the table for more information.
Always use a DMX controller with digital interface. If not available, you can purchase the CLS D-ta DMX addresser unit (
#122200
).
First make sure to set the DATA on the DMX controller. To program the setting into the LED fixture follow the next steps.
2020 CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all aliated companies disclaim
liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to
use or reliance on the information contained in this manual. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from CLS-LED BV. Other legal information can be found in our General conditions, found on the back of
your CLS-LED BV invoice, inside the CLS catalogue or on our website www.cls-led.com/General-Terms.pdf
www.cls-led.com www.cls-led.com
7 8
REFLECTOR REPLACEMENT
4Assemble
1
5
2
3
6
Align
LIST OF SYMBOLS
Multiple connection
Daisychain connectivity
Installation depth
In centimeters
Swivel
Fixture is horizontally rotatable,
indicated in degrees
Swivel
Fixture is vertically rotatable,
indicated in degrees
Installation size
In centimeters
Application area
Indoor or outdoor
Application area
Floor, wall or ceiling
Protection class
One, two or three
Cable length
Maximum cable attached
to the fixture in centimeters
Lifespan
Of the light source in hours
Driver
Inclusive or exclusive
Internal or external
Pressure
Maximum pressure on the
fixture in kg/cm2
Weight
In grams/kilograms
Curve
Minimal bending curve
in centimeters
LED pitch
Pitch between the LEDs
in millimeters
Power supply
In VDC, VAC or milliAmpere
Power consumption
In VA or Watt
IP value
Ingress Protection classifies the
degrees of protection provided against
the intrusion of the product
Cutting length
Indicated by the cutting
marks
LEDs
Kind of LED used in the
fixture
Lenses
Availble lenses,
indicated in degrees
Performance Zoom
Adjustable beam angle
Plug & play
Easy connection using the
SmartConnect system
White colour temperature
In dierent Kelvin values;
Cold white, neutral white, warm
white or extra warm white
Colour
Available colours;
Amber, blue, red or green
Colour changing
RGB, RGB-W, RGB-A,
AWB or Tunable White
DMX input
Fixture works on DMX512
protocol or Wireless DMX
Magno dimming
Accurate dimming from
100 - 1% by using a magnet
Dynamic Control
Dynamic Power Control or
Dynamic Temperature Control
Combined product
Compose your own fixture
Warranty
3 or 5 years warranty on
the product
Energy label
Conformité Européenne
CE marking for free marketability
of industrial goods within the EU
r
h
ø w d
Dimmable
1-10 Volt, Phase, individual,
DMX dimmable or DALI
DRIVER
INCLUDED
DRIVER
EXTERNAL
Retail & Food LED modules
Clothing, furniture, kitchens, jewellery,
shoes, bread, meat, fish and
vegetables & fruit.
Lightsource
Equipped with a CLS, Citizen or a Xicato
LED module
Bluetooth controlled
By Casambi
PWM dimming
Traditional PWM dimming, DMX analog
or DMX Hybrid dim
CLS
DYNAMIC
COLOUR
COB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CLS Mika ColourFlow & Tunable White Owner's manual

Brand
CLS
Model
Mika ColourFlow & Tunable White
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents